Search

This paper presents an approach for dealing with the control of five-level, diode-clamped rectifiers. The control of such converters is challenging, as voltage balancing among capacitors is not a trivial task. Some of the existing approaches that cope with this problem use specific modifications of one of the traditional modulation techniques, such as using redundant vectors in space vector modulation (SVM). The main feature of the proposed technique is that part of the modulation is considered in the system equations and, in this way, the voltage balance can be solved designing a specific controller for this problem. As a result, several levels are used within a switching period. Furthermore, it is shown that the proposed approach hardly affects the control of active and reactive powers and total dc-link voltage in such a way that the well-known direct power control can be applied. As a consequence, the resultant modulation stage is simpler than other techniques based on, e.g., SVM. The effectiveness and good performance of the system under the proposed control approach are validated by both simulation and experimental results. [ABSTRACT FROM AUTHOR]

The hybrid modular multilevel converter with cascaded full bridges (HMMC-CFB) is a recently proposed dc fault tolerant converter topology for high-power applications. It has a director part (DP) consisting of a series of connected half-bridge submodules, and a wave-shaping part (WSP) composed of a series of connected full-bridge submodules (FBSMs). The submodules in DP avoid high voltage stresses and improve synchronization between DP and WSP by slowing down the change rate of DP output voltage. This slowdown is achieved by using a trapezoidal reference signal for DP. The WSP attenuates the voltage harmonics produced by DP. However, the energy exchanged by WSP changes with modulation index, which may cause improper voltage regulation of the submodule capacitors. This paper proposes a new control technique to regulate the energy exchanged by WSP, which uses a variable slope trapezoidal reference signal of DP. To obtain this slope, the feedforward and feedback controllers are used. The feedforward controller gives the value of slope depending on the modulation index (mv) to keep the energy exchanged by WSP nearly equal to zero, whereas the losses and nonideality of the converter are taken care of by the feedback controller. This technique guarantees proper voltage regulation of the submodule capacitors for all modulation indices. The efficacy of the proposed technique is confirmed using simulations and experimentations. This paper also presents a circulating current suppressing controller for HMMC-CFB. The proposed control schemes and dc fault tolerant capability of HMMC-CFB are tested on a grid-connected model built in PSCAD. [ABSTRACT FROM AUTHOR]

This paper proposes a new fault-tolerant strategy for the purpose of revamping the performance of three-phase multilevel (ML) converters with faulty switches. The proposed fault-tolerant strategy is based on an adaptation of the modified space vector modulation (SVM) technique to the fundamental phase-shift compensation method. The proposed fault-tolerant strategy generates balanced line-to-line voltages with increased voltage levels in the faulty condition. In this paper, first a brief background about cascaded H-bridge (CHB) ML converters and SVM technique is provided. Then the proposed fault-tolerant strategy and the modified SVM technique are presented. Finally, several experimental results are provided to validate operation of the proposed strategy. [ABSTRACT FROM AUTHOR]

This paper presents a modular multilevel series/parallel converter (MMSPC) with intermodule switched-inductor power transfer. The switched-inductor voltage conversion feature allows controllable and efficient transfer of energy between modules with nonnegligible voltage difference, providing both step-down and step-up functionalities. Thus, this converter can accurately control and rapidly adjust the voltage of each module to generate an ac output voltage waveform with a controllable number of levels, increasing the quality of the output. Moreover, the intrinsic dc–dc conversion feature can generate a dc controllable output voltage and enable new applications. In this text, we specifically demonstrate how the flexibility of obtaining both ac and dc output with the same setup renders the topology promising for battery energy storage systems and dc microgrid applications. Experimental results validate the topology and concept of an MMSPC with intrinsic switched-inductor conversion. [ABSTRACT FROM AUTHOR]

Conventional two-level as well as multilevel voltage-source-inverter topologies with a hexagonal voltage-space vector structure generate low-order harmonics in the machine terminal voltages when operated beyond the linear modulation range in variable speed drive application. Progressing from hexagonal to a higher sided polygonal voltage-space-vector structure (VSVS) suppresses significant low-order harmonics throughout the modulation range. In addition, the linear modulation range will also be enhanced very near to the base speed. In this paper, for the first time, the generation of a multilevel 24-sided VSVS using a single dc source for induction-motor drives is proposed. A cascaded topology with a dc-source-fed flying-capacitor inverter and two low-voltage capacitor-fed H-bridge cells forms the power circuit. The features and advantages of the proposed scheme are validated through experimental results and discussions. [ABSTRACT FROM AUTHOR]

Owing to low cost, small size, and low weight, transformerless inverters became prominent in single-phase grid connected photovoltaic (PV) systems. Key issues pertaining to these inverters include suppression of common mode (CM) leakage current and improvement of conversion efficiency. Achieving higher efficiency in single-phase grid-connected photovoltaic systems depends on the number of stages involved in feeding power to the grid, predominantly, if the PV array voltage is less than the peak value of the grid voltage. In this paper, an integrated dc–dc converter based grid-connected transformerless PV inverter is proposed which is aimed at maintaining high efficiency, even if the PV array voltage falls below the peak value of grid voltage (efficient operation at an extended input voltage range). A modulation strategy is discussed in order to minimize the flow of CM leakage current. Further, the efficiencies of certain transformerless inverter topologies are analyzed and compared with that of the proposed topology. Detailed simulation studies are carried out in MATLAB/Simulink environment to verify the analysis. Experimental results for a scaled down laboratory prototype are included as a proof-of-concept to validate the claims. [ABSTRACT FROM AUTHOR]

This paper proposes a new multilevel converter based on the cascade connection of double flying capacitor multicell (DFCM) converters, as multilevel modules, to decrease the voltage diversity of the flying capacitors. Furthermore, a new switching pattern based on the phase-shifted pulse-width modulation technique is proposed to reduce the voltage ripple across the flying capacitors. Moreover, the proposed modulation technique reduces the rms value of the current flowing through flying capacitors. This results in an increase in the life time of flying capacitors and a decrease in the capacitance of the flying capacitors, to keep the same amount of the ripple, meaning a reduction in the physical size of the converter. In addition, this paper presents an analytical approach to calculate the average and rms currents of the insulated gate bipolar transistors (IGBTs)/diodes in the DFCM converter in a closed-form expression. The derived closed-form equations to calculate the average and rms currents of the IGBTs/diodes are utilized to investigate the conduction power losses in a DFCM converter and the proposed multilevel converter. Numerical results of the derived closed-form equations match the simulation results well, which validates the derived equations. Furthermore, simulation results and experimental measurements of the proposed multilevel power converter, configured by cascading two two-cell five-level DFCM converters, are presented to validate the performance of the proposed converter as well as the suggested modulation technique. [ABSTRACT FROM AUTHOR]

This paper presents a dual modular multilevel converter (MMC) topology that utilizes energy exchange between adjacent-arm submodules (SMs), operating with out-of-phase modulation. The proposed configuration is applicable to medium-voltage high-power variable-speed drives incorporating open-end stator winding machines. A novel concept of power decoupling between adjacent-arm SMs in the dual MMC topology is realized through high-frequency transformer-based dc–dc converter modules. This concept offers a significant reduction in the sizing requirement of the SM capacitance and the stored energy in the MMC system, while avoiding the problem of wide voltage fluctuations of SM capacitors, especially at low operating frequencies. The proposed configuration can produce dc voltage; therefore, a machine speed range from zero speed to the rated speed is possible under the rated torque operating condition. The operating principles of the proposed dual MMC configuration are elaborated and necessary mathematical analysis is derived. Simulation and experimental results verify the concept of the proposed drive configuration. [ABSTRACT FROM AUTHOR]

This paper presents an optimized topology of 3-$\phi$ , multilevel inverter (MLI) configuration for five or higher level operation with reduced switch count. The proposed solution consists of two basic units (BUs) of multilevel converter and a T-structured 3-level inverter (3-LI). Both BUs are equally shared by the three phases maintaining symmetry among the phases. Moreover, for a higher level operation of the proposed MLI, the modifications required are at two BUs only and not at three legs of the inverter. It further helps in reducing the requirement of extra components for higher level operation compared to the conventional solutions. Furthermore, the topology also has the benefits of reduced switching and conduction loss. An algorithm is also devised to generate the switching pulses for the BUs and the 3-LI, using a carrier-based space vector modulation technique. Presented topology is compared with other existing topologies to prove its advantage. All the details regarding the operating modes and pulse width modulation techniques employed for the proposed system are given and supported by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

Adding the auxiliary switches to the conventional H-bridge inverter is an effective way to eliminate the leakage current for transformerless PV systems, such as H5, H6, etc. Inspired by the newly developed embedded-switch H6 topology, a novel embedded-switch inverter (ESI) is proposed in this paper for three-phase transformerless PV systems. First, the operation principle and characteristics of the proposed ESI are analyzed. Second, the common-mode model of the three-phase ESI is established, based on which the main factors that affect the leakage current are discussed. The finding reveals that the switching states with conventional modulation strategy result in high-frequency common-mode voltage, which is the source of leakage current. In order to solve the problem, a new modulation strategy is presented for ESI to eliminate the high-frequency leakage current. Finally, the time-domain simulation and the experimental tests are carried out. The results verify the effectiveness of the proposed solution. [ABSTRACT FROM AUTHOR]

Grid-connected power conversion systems for renewable energy sources must fulfill several requirements, e.g., the high efficiency, the reduced cost and complexity, and, quite often, the boost capabilities that is usually achieved using a front-end dc–dc boost converter before the inversion stage, leading to a two-stage architecture. Meanwhile, single-stage power conversion systems, which perform the boosting operation within the inversion one, offer some potential advantages, in terms of reducing the complexity and the volume of the whole system. Among several proposed options, the split-source inverter (SSI) has been recently proposed by Abdelhakim et al. as an alternative option with some interesting features to the commonly used Z-source inverter. Taking into account that the SSI is controlled by a single parameter, i.e., its dc and ac sides are controlled by the modulation index, it is of paramount importance to investigate its control scheme in grid-connected mode, which has never been studied yet. Hence, this paper models the SSI dc side and proposes a modified modulation scheme combined with the commonly used synchronous reference frame control technique to achieve a decoupled control scheme of the SSI in grid-connected mode, i.e., the dc and the ac sides of the SSI can be controlled independently, which is convenient for many applications. The introduced control scheme is analyzed and simulated using a MATLAB/Simulink model, where a reduced scale 1-kVA grid-connected SSI is designed and simulated for the sake of experimental validation. Finally, the designed system is implemented experimentally to validate and verify the reported analysis and simulations. [ABSTRACT FROM PUBLISHER]

This paper presents a matrix-based nonisolated three-phase ac–dc converter with a current-doubler rectifier (CDR) circuit. Buck-type rectifiers are normally used for step-down ac-to-dc conversion. However, for three-phase buck rectifiers, the lower bound of rectified dc voltage is limited as the converter is severely underutilized by operating at lower modulation index. Moreover, at lower modulation index, the rms values of current increases contributing to higher conduction losses. However, by using a matrix (3 × 1) topology followed by a CDR, the desired dc output voltage can be reduced by half. The matrix topology directly converts three-phase line frequency ac voltages into intermediate high-frequency ac voltage which is subsequently, rectified using a CDR to obtain the required output dc voltage. A modified space vector modulation based modulation scheme especially suited for the proposed converter is presented for superior input power quality with reduced power loss. Comprehensive analysis and design of the proposed converter is carried out followed by simulation and laboratory-based experimental tests. Subsequently, the loss analysis of the proposed converter is carried out and a comparative evaluation of the proposed converter with the traditional six-switch buck rectifier is provided to demonstrate the suitability of the proposed converter for large step-down voltage gain. Digital implementation of the proposed modulation scheme is carried out at 40-kHz switching frequency. A hardware prototype of 500 W is developed to validate the theoretical and simulation results. [ABSTRACT FROM AUTHOR]

Hybrid multilevel converters combine features of conventional multilevel topologies to provide an acceptable tradeoff between the advantages and disadvantages of these converters. For many industrial applications, common dc link is a requirement that limits the choice of topologies to neutral point clamped (NPC) and flying capacitor multicell (FCM) hybrid types. This paper investigates the operation of a hybrid five-level topology and proposes a modulation method that takes the advantage of the combined features of NPC and FCM. The dual flying capacitor (FC) active-neutral-point-clamped (DFC-ANPC) converter provides certain advantages such as natural soft switching of line frequency switches, elimination of the transient voltage balancing snubbers, and a more even loss distribution. Simulation results and experimental verification of the five-level DFC-ANPC converter are presented to validate the performance of the converter as well as the applied modulation technique. [ABSTRACT FROM AUTHOR]

This paper proposes a voltage balancing method for stacked multicell converters (SMCs) based on phase-disposition pulse-width modulation (PD-PWM). In order to reduce the switching transitions of the power devices, only optimal transitions between consecutive voltage levels are used. Selection of the optimal transition sequence is performed by evaluating a cost function. Significant reductions in the switching transitions and power losses of the power devices are achieved as compared to the optimal-state voltage balancing method where nonoptimal transitions are allowed. Simulation and experimental results from a seven-level $3\times 2$ SMC verifies that the proposed PD-PWM voltage balancing method is robust under linear/nonlinear loads and transients. [ABSTRACT FROM AUTHOR]

Three-level topologies are widely used in back-to-back converters of wind turbine generation (WTG) systems. In comparison with a conventional two-level topology, three-level topologies have more advantages, particularly for the high power. Neutral-point clamped (NPC) and T-type are typical three-level topologies. An open-switch fault of a three-level rectifier that is connected to a permanent-magnet synchronous generator (PMSG) leads to the current distortion and torque vibration in WTG systems. Furthermore, WTG systems can break down in the worst case. Therefore, a tolerance control for open-switch faults is required to improve the reliability of WTG systems. WTG systems by applying the tolerance control can be stopped safely and prevent additional problems. Depending on the situation, it can keep the operation of WTG systems under open-switch fault. The effects of outer open-switch faults of three-level rectifiers are analyzed by considering PMSG specifications in this paper. Moreover, a tolerance control for outer open-switch faults of the NPC and T-type three-level rectifiers are proposed with existing tolerance controls for inner open-switch faults. The proposed tolerance control is to inject the exact $d$-axis current value to eliminate current distortion. The simulation and experiment are conducted to prove the feasibility of the proposed tolerance control and to identify its performance. [ABSTRACT FROM PUBLISHER]

Efficient power conversion technologies are strategic to the advancement of fuel cell vehicles (FCVs). This paper presents an overview of power conditioning system (PCS) architectures for an FCV propulsion system. Two new power conversion topologies to obtain variable ac from the fuel cell system are proposed. The switching of the power devices are based on the proposed hybrid modulation technique that minimizes the switching losses in the inverter. The proposed converters do not use the dc-link filter capacitors. Elimination of the dc-link capacitor not only reduces the size and volume but also helps in retaining the sine wave modulated information at the input of a three-phase inverter. Bidirectional converter topologies are proposed for interfacing low-voltage battery and fuel cell dc bus. Experimental results are presented for the proposed topologies. [ABSTRACT FROM AUTHOR]

This paper proposes a multiple-input versatile matrix converter (VMC) for integrating hybrid ac/dc energy resources and storages to the power grid. The VMC is developed from the traditional indirect matrix converter but operates in the reverse-boost mode rather than in the forward-buck mode. The reverse-boost mode is more relevant here since most renewable sources and energy storages have lower voltages than the grid. The eventual VMC developed uses an alternative nine-switch converter, rather than usual six-switch voltage-source converter, for providing six input terminals in total. One three-phase ac source and three dc sources, or other source combinations, can therefore be connected to the VMC. Powers from these sources are channeled to the three-phase utility grid through the VMC's current-source inverter. Their proper dispatches are guaranteed by the proposed control and modulation schemes, which also help maintain near-sinusoidal input and output current waveforms. Mathematical proofs, simulation, and experimental results have shown that the VMC can indeed operate as intended. [ABSTRACT FROM PUBLISHER]

A new scheme for nine-level voltage space-vector generation for medium-voltage induction motor (IM) drives with open-end stator winding is presented in this paper. The proposed nine-level power converter topology consists of two conventional three-phase two-level voltage source inverters powered by isolated dc sources and six floating-capacitor-connected H-bridges. The H-bridge capacitor voltages are effectively maintained at the required asymmetrical levels by employing a space vector modulation (SVPWM) based control strategy. An interesting feature of this topology is its ability to function in five- or three-level mode, in the entire modulation range, at full-power rating, in the event of any failure in the H -bridges. This feature significantly improves the reliability of the proposed drive system. Each leg of the three-phase two-level inverters used in this topology switches only for a half cycle of the reference voltage waveform. Hence, the effective switching frequency is reduced by half, resulting in switching loss reduction in high-voltage devices. The transient as well as the steady-state performance of the proposed nine-level inverter-fed IM drive system is experimentally verified in the entire modulation range including the overmodulation region. [ABSTRACT FROM PUBLISHER]

Combining concepts of traditional multilevel converter and matrix converter (MC), the multimodular MCs (MMMCs) have reached the medium-voltage high-power level. These topologies possess features such as elimination of dc components and are able to output high-quality multilevel waveforms. Due to the MMMC's particular topological structure, modulation strategies for the conventional converters cannot be directly adopted. This necessitates the design of specially tailored modulation schemes for them to generate sinusoidal input/output waveforms. In this paper, indirect space-vector-based modulation techniques are proposed for the MMMCs. The study begins by establishing an indirect circuit model for the three-module MMMC topology, before using space vector calculations to derive duty ratios for the model's rectification and inversion stages. As the inversion stage can be viewed as multiple sets of three-phase outputs, its switching states and duty ratios are then converted and combined with those from the rectification stage. Finally, the gating signals are produced according to two switching patterns. As demonstrated by simulation and experimental results, the presented modulation techniques can generate sinusoidal waveforms with variable frequency and magnitude, as well as adjustable angle and power factor. The superiority of the second switching pattern is also proved by the obtained results. [ABSTRACT FROM PUBLISHER]

The Z-source inverter is a relatively recent converter topology that exhibits both voltage-buck and voltage-boost capability. The Z-source concept can be applied to all dc-to-ac, ac-to-dc, ac-to-ac, and dc-to-dc power conversion whether two-level or multilevel. However, multilevel converters offer many benefits for higher power applications. Previous publications have shown the control of a Z-source neutral point clamped inverter using the carrier-based modulation technique. This paper presents the control of a Z-source neutral point clamped inverter using the space vector modulation technique. This gives a number of benefits, both in terms of implementation and harmonic performance. The adopted approach enables the operation of the Z-source arrangement to be optimized and implemented digitally without introducing any extra commutations. The proposed techniques are demonstrated both in simulation and through experimental results from a prototype converter. [ABSTRACT FROM AUTHOR]