Search

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

This paper proposes a dual-space vector control scheme for the open-end winding permanent magnet synchronous motor (OEW-PMSM) drive fed by the dual inverter with a single dc supply. Potential zero-sequence current in the open-end winding drive system has to be considered since it causes circulating current in the winding and leads to high current stress of power semiconductor devices and high losses. Zero-sequence current in open-end winding ac motor drives is usually caused by the zero-sequence voltage, and therefore switching combinations which do not produce zero-sequence voltage are used to synthesize the reference voltage in existing methods. But even so, the zero-sequence voltage can also be produced by the dead time of the inverter. In order to suppress zero-sequence current in the OEW-PMSM drive, a dual-space vector control scheme is proposed and a novel dual-inverter space vector pulse width modulation (PWM) with the zero-sequence voltage reference is employed to regulate system zero-sequence voltage in this paper. Compared with existing dual inverter PWM strategies, the novel algorithm build a regulation mechanism for the zero-sequence voltage. The proposed method is compared with the conventional vector control by simulations and experiments, and the results shown that the proposed scheme can suppress zero-sequence current effectively. [ABSTRACT FROM AUTHOR]

The increasing interest in multiphase drive systems has led to the extension of inverter topologies and pulse width modulation (PWM) methods from three-phase to multiphase occasions. Carrier-based PWM (CPWM) dominates space vector PWM when the phase number increases, because of its simple computation and modular implementation. Although intensive work has been done on modifying PWM methods to reduce the common-mode voltage (CMV), not enough work has been done on CPWM methods with CMV reduction for multiphase drives. This paper extends the phase-shifted sinusoidal PWM (PS-SPWM) method for five-phase and six-phase two-level voltage-source inverters (VSI) and employs the intersection-plotting method and Fourier analysis to reveal the nature of the CMV. Both experiment and simulation results comply with theoretical analysis that compared with the conventional SPWM, the PS-SPWM can effectively reduce the CMV in peak-to-peak value and RMS value, though it leads to a higher phase current distortion. In addition, the hardware realization of PS-SPWM for multiphase inverters by a distributed control system is presented in this paper. [ABSTRACT FROM AUTHOR]

An adaptive control of DPWM implementable in clamped-three-level inverters with two strings of photovoltaic (PV) panels in cascaded connection is proposed in this paper. The proposed modulation is developed based on the so-called circuit-level decoupling concept. It is able to provide balance line voltage even under unbalanced dc links. The unequal dc voltages appeared due to asymmetric maximum point of power trackings (MPPTs) are controlled by proper injection of zero-sequence voltage to the common mode voltage, while the total dc voltage is regulated based on the voltage commands generated by the MPPT of each string. Thus, both PV strings are able to be operated based on their MPPTs while there is almost no low-order harmonic distortion at the inverter output current. Compared with the previous methods, the high capability of the proposed method is evaluated by simulation study and experimental tests. [ABSTRACT FROM AUTHOR]

This paper investigates a multilevel inverter composed of series/parallel-connected H-bridges. The presented structure can be used for applications in which the use of semiconductor switches with low-voltage and low-current ratings is intended. A comprehensive system model, an overall control strategy to adjust the output voltage with constant magnitude and frequency, and a level-shifted PWM (LS-PWM) strategy based on a voltage vectors unidimensional analysis and a plane analysis are presented. The LS-PWM is capable of mitigating the low-frequency circulating current, thus generating multilevel voltage signals with low harmonic distortion, maximum number of levels, and low dv/dt. In addition, considering a wide range of values of voltages and currents and various power levels, the total converter losses are reduced compared with the conventional multilevel converters. Two multilevel conventional inverters with the same number of semiconductor switches are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

This paper presents a nine-level transformer-based inverter requiring only eight switches. The envisaged structure consists of two standard H-bridges fed from a single dc source. Besides, a single-phase transformer is employed to aid the process of intermediate voltage level generation. An ad-hoc pulsewidth modulation scheme based on boolean logic form equations is developed to derive the gating pulses. An effortless extension of the proposed inverter to a higher number of voltage levels is also achieved by generalizing the switching functions. Furthermore, the superior performance of the proposed topology is demonstrated through a comprehensive cost-based analysis. Finally, the validation of the proposed topology is accomplished through experiments on a down-scale prototype, and the measurement results are included. [ABSTRACT FROM AUTHOR]

A new pulsewidth modulation (PWM) strategy which is an alternative approach of the discontinuous PWM (DPWM) for a three-level neutral-point-clamped (NPC) inverter is proposed in this paper. A three-level NPC inverter is completely mature and very well-established topology in high-power applications. However, the three-level NPC inverter has an inheritance problem of the neutral-point voltage unbalancing due to the split dc-link capacitors. This structure can cause large neutral-point voltage ripple. Furthermore, output currents of the three-level NPC inverter are distorted by the neutral-point voltage ripple. Therefore, the neutral-point voltage must be controlled. In this paper, a new DPWM method using two different offsets for the neutral-point ripple reduction is proposed and the effectiveness of the proposed DPWM method is verified by using the simulation and the experimental results. [ABSTRACT FROM PUBLISHER]

A four-level five-phase open-end winding (OeW) drive topology is introduced in this paper. The drive comprises a five-phase induction machine with open-end stator windings, supplied using two two-level voltage-source inverters with isolated and unequal dc-link voltages, in the ratio 2 : 1. The topology offers the advantages of a modular structure with fewer semiconductor components and has a greater potential for fault tolerance, as compared with an equivalent single-sided four-level drive. Due to the large number of switching states, development of a suitable space vector pulsewidth-modulation (PWM) method can be challenging. Hence, this paper examines the implementation of two-level-shifted carrier-based PWM methods. The effect of dead time on the drive performance is discussed, and it is shown that simultaneous PWM switching of both inverters can lead to degraded output phase voltage waveforms. Detailed analysis of this phenomenon is presented, a solution is proposed, and the modified modulation techniques are incorporated in an experimental setup, at first in conjunction with $V/f$ control. Once the proof of concept has been provided, full field-oriented control is implemented in this OeW drive topology for the first time; detailed experimental testing is conducted, and results are reported. [ABSTRACT FROM AUTHOR]

This paper presents an optimized topology for a \text3-\phi three-level inverter with complete elimination of common-mode voltage (CMV). The proposed multilevel inverter (MLI) configuration is realized by modifying a T-structure \text3-\phi inverter. The proposed configuration is an optimized solution with respect to the pulse-width modulation strategy used for CMV elimination. The given three-level inverter structure uses only 16 power semiconductor switches, which is much lower than the existing configurations. A reduced number of power semiconductor devices results in a diminished number of driver circuits, less installation space, and low cost. Further, due to the complete elimination of CMV, the proposed MLI is free from issues such as electromagnetic interference and leakage current with a reduction in filter requirement. The presented topology is also compared with other existing topologies to prove its advantage. It is an optimized solution with respect to the dc bus voltage requirement and the total voltage rating of the devices or the components used in the system. Simulation and experimental results are presented to confirm the capability of the proposed MLI. [ABSTRACT FROM AUTHOR]

This paper proposes a single-phase, single-stage buck–boost inverter for photovoltaic (PV) systems. The presented topology has one common terminal in input and output ports which eliminates common mode leakage current problem in the grid-connected PV applications. Although it uses four switches, its operation is bimodal and only two switches receive high-frequency pulse width modulation signals in each mode. Its principle of operation is described in detail with the help of equivalent circuits. Its dynamic model is presented, based on which a bimodal controller is designed. Experimental results, in stand-alone and grid-connected mode, obtained with a 300-W laboratory prototype are presented to validate its performance. [ABSTRACT FROM AUTHOR]

This paper addresses the inverter nonlinearity of a three-level T-type inverter. The main causes of the nonlinearity are pulse shaping, pulse skipping due to narrow pulses for the dead time, and voltage drop of the switching devices. Although the same causes have existed in two-level inverters, the pulse skipping phenomenon and results are quite different in the case of the three-level T-type inverter. The effects of pulse shaping and skipping have been investigated and discussed. In addition, the voltage drop of the switching devices has been considered in conjunction with the conduction path of the T-type inverter. Compensation methods based on the pulse width modulation (PWM) of T-type inverter to alleviate the inverter nonlinearity have been proposed from research results. The proposed methods could be easily implemented by adding appropriate offset voltages to the voltage references of the inverter in PWM. Furthermore, a neutral voltage balancing method of a three-level T-type inverter has been proposed in conjunction with the proposed PWM methods using offset voltage. Through extensive experimental tests, the fifth- and seventh-harmonic components of the current are conspicuously reduced along with the even harmonics. The neutral voltage of the inverter can be balanced effectively with the proposed offset voltage adjustments as well. [ABSTRACT FROM AUTHOR]

By using a carrier-based pulse width modulation, this paper presents a developed phase-shift space vector modulation strategy for a nine-switch inverter to overcome one of major drawbacks, i.e., output voltage and current distortion. This is due to the crossover of modulating waves per phase based on the different phase-shift angle between dual terminals. The proposed strategy done by mathematical algorithms based on the critical operating point principle accomplishes in the wide range of phase-shift conditions that contribute in both common- and difference-frequency modes with its expediency of uncomplicated computation and handy implementation. Even more, the identical and nonidentical modulation index techniques are wholly brought up. The feasibility of the proposed strategy is confirmed by results of the simulation directly compared with the experiment, showing in good accordance with the theoretic analysis. [ABSTRACT FROM AUTHOR]

A new single-phase \uppi-\texttype 5-level inverter using 3-terminal switch-network (3TSN) is proposed in this paper. The topology is considered as a variant of T-type 3-level structure or dual-buck inverter with coupled inductors. This new inverter is suitable for multilevel power inversion with low dc-bus voltage. The merit of the proposed topology is to apply only four active power switches to achieve 5-level operation. Other benefits include double frequency operation of output inductor and equal division of the current that flows through power switches and filter inductor. Hence, it leads to high efficiency and low harmonics. These characteristics allow improvement of losses distribution and volume reduction of output filter inductor. The operation scenario with sinusoidal pulsewidth modulation (SPWM) is described in details. Meanwhile, the magnetic analysis and design are studied and discussed. Finally, a prototype is built to verify the theoretical analysis and demonstrate the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents a novel topology for a direct ac–ac power converter, called as the “three-to- k” phase matrix converter. The input to the proposed matrix converter configuration is a three-phase fixed voltage and a fixed frequency supply from the grid. The output is a variable voltage and variable frequency ac supply of any number of phases (k phase). However, the discussion is limited here for a k that is equal to odd number of phases. As an example, a “three-to-five” phase matrix converter is utilized for discussion and analysis. This paper also proposes two pulsewidth modulation (PWM) control techniques for the general topology of the “three-to- k” phase matrix converter. This is based on the so-called direct duty ratio PWM (DPWM). In one presented technique, the output voltage is limited to one half of the input voltage. For the other proposed scheme, the output voltage is enhanced to 78.86% of the input voltage. The proposed control algorithm is validated using simulation and an experimental approach. [ABSTRACT FROM AUTHOR]

In this paper, a new inverter topology is proposed for generating a multilevel dodecagonal voltage space vector structure for open-end winding induction motor (IM) using a single dc source. Dodecagonal voltage space vector structure eliminates fifth- and seventh-order harmonic voltages from phase voltage output and hence eliminates the fifth- and seventh-order harmonic currents through the motor leading to removal of the dominant sixth-order torque ripple generation in the motor over the entire modulation range. Multilevel space vector structure generates output voltage with better THD and low dv/dt. In the proposed topology, two three-level inverters drive an open-end winding IM, one inverter from each side. DC-link of primary inverter is from a dc source which delivers the entire active power, whereas the secondary inverter dc-link is maintained by a capacitor, which is self balanced during the inverter operation. The PWM scheme implemented ensures low switching frequency for primary inverter. Secondary inverter operates at a small dc-link voltage. Hence, switching losses are small for both primary and secondary inverters. Experimental results show the elimination of fifth- and seventh-order harmonic voltages over the entire modulation range, validating effectiveness of the proposed multilevel inverter scheme. [ABSTRACT FROM PUBLISHER]

A capacitor voltage-balancing method for a nested neutral point clamped (NNPC) inverter is proposed in this paper. The NNPC inverter is a newly developed four-level voltage-source inverter for medium-voltage applications with properties such as operating over a wide range of voltages (2.4–7.2 kV) without the need for connecting power semiconductor in series and high-quality output voltage. The NNPC topology has two flying capacitors in each leg. In order to ensure that the inverter can operate normally and all switching devices share identical voltage stress, the voltage across each capacitor should be controlled and maintained at one-third of dc bus voltage. The proposed capacitor voltage-balancing method takes advantage of redundancy in phase switching states to control and balance flying capacitor voltages. Simple and effective logic tables are developed for the balancing control. The proposed method is easy to implement and needs very few computations. Moreover, the method is suitable for and easy to integrate with different pulse width modulation schemes. The effectiveness and feasibility of the proposed method is verified by simulation and experiment. [ABSTRACT FROM PUBLISHER]

This paper investigates a dynamic voltage restorer (DVR) composed of two conventional three-phase inverters series cascaded through an open-end winding (OEW) transformer, denominated here DVR-OEW. The DVR-OEW operating with either equal or different dc-link voltages is examined. The proposed topology aims to regulate the voltage at the load side in the case of voltage sags/swells, distortion, or unbalance at the grid voltage. A suitable control strategy is developed, including space-vector analysis, level-shifted PWM and its equivalent optimized single-carrier PWM, as well as the operating principles and characteristics of the DVR. Comparisons among the DVR-OEW and conventional configurations, including a neutral-point clamped converter-based DVR, are furnished. The main advantages of the DVR-OEW compared to the conventional topologies lie on: 1) reduced harmonic distortion, 2) reduced converter losses, and 3) reduced voltage rating of the power switches. Simulated and experimental results are presented to validate the theoretical studies. [ABSTRACT FROM AUTHOR]

Dodecagonal (12-sided) space vector pulsewidth modulation (PWM) schemes are characterized by the complete absence of (6n ± 1)th-order harmonics (for odd n) in the phase voltages, within the linear modulation range and beyond, including overmodulation. This paper presents a new topology suitable for the realization of such multilevel inverter schemes for induction motor (IM) drives, by cascading two-level inverters with flying-capacitor-inverter fed floating H-bridge cells. Now, any standard IM may be used to get the dodecagonal operation which hitherto was possible only with open-end winding IM. To minimize the current total harmonic distortion (THD), a strategy for synchronous PWM is also proposed. It is shown that the proposed method is capable of obtaining better THD figures, compared to conventional dodecagonal schemes. The topology and the PWM strategy are validated through analysis and subsequently verified experimentally. [ABSTRACT FROM AUTHOR]

In this paper, a novel single-phase five-level inverter is proposed using coupled inductors. This inverter can output five-level voltage with only one dc source. No split of the dc voltage capacitor is needed, totally avoiding the voltage balancing problem in conventional multilevel inverters. The level of the output voltage is only half of the dc-link voltage in all conditions, leading to much reduced dv/dt . This inverter is based on the widely used three-arm power module and the voltage stresses on all the power switches are the same, making it very easy to construct. Operation mechanism of this inverter is analyzed and the possible switching patterns are investigated. Based on these analyses, a novel optimized modulation scheme is presented. With this modulation method, no dc components exist in the inductor currents, which is very helpful for minimization of the inductors. Simulation and experimental results show the validity of the proposed inverter together with the optimized modulation scheme. [ABSTRACT FROM AUTHOR]

The novel multilevel circuit topologies are proposed in this paper. They are called multilevel circuit topologies based on switched-capacitor and diode-clamped converters (MCT-BSD). The topology structure and the operation principle, including the working states’ transitions of the diode-clamped part, the voltages balancing mechanism of the dc link capacitors, and the pulse width modulated carrier control strategy are given. The switched-capacitor circuits contribute not only to balancing the voltages of capacitors but also to boosting the output voltage with a certain input dc voltage. The validity of the MCT-BSD is verified by simulations and experiments. The results show that balancing the voltages of capacitors, boosting the output voltages, and operating under the three-phase condition are all realized effectively in the MCT-BSD. The simulations also show the generalization of the MCT-BSD for n-level topologies. [ABSTRACT FROM AUTHOR]

Unipolar sinusoidal pulsewidth modulation (SPWM) full-bridge inverter brings high-frequency common-mode voltage, which restricts its application in transformerless photovoltaic grid-connected inverters. In order to solve this problem, an optimized full-bridge structure with two additional switches and a capacitor divider is proposed in this paper, which guarantees that a freewheeling path is clamped to half input voltage in the freewheeling period. Sequentially, the high-frequency common-mode voltage has been avoided in the unipolar SPWM full-bridge inverter, and the output current flows through only three switches in the power processing period. In addition, a clamping branch makes the voltage stress of the added switches be equal to half input voltage. The operation and clamping modes are analyzed, and the total losses of power device of several existing topologies and proposed topology are fairly calculated. Finally, the common-mode performance of these topologies is compared by a universal prototype inverter rated at 1 kW. [ABSTRACT FROM AUTHOR]