Search

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

Unipolar-pulsewidth modulation (UP-PWM) inverter takes advantages of high power efficiency and small output chokes which is widely used in the industry. However, UP-PWM inverters cannot be used in parallel operation due to a current unbalance problem. This paper studies the current unbalance problem of paralleled UP-PWM inverters with common dc bus and ac bus. First, the problem of unbalanced inductor current is defined and analyzed. Second, a technique to eliminate unbalanced currents is proposed. The proposed current balancing technique only requires one more current sensor in an inverter module rather than changing converter topology or modulation method, which makes it possible to apply UP-PWM inverters in parallel-operation while keeping the advantages of unipolar switching. The proposed current balancing method is verified by both simulation and hardware experiment. Experimental verification is performed on two 1 kW, 400 V input, and 120 V/60 Hz output prototypes, which shows a good agreement to the analytical study. [ABSTRACT FROM AUTHOR]

In several electrical dc–ac power conversions, the ac output voltage is higher than the input voltage. If a voltage-source inverter (VSI) is used, then an additional dc–dc boosting stage is required to overcome the step-down VSI limitations. Recently, several impedance source converters are gaining higher attentions [1], [2], as they are able to provide buck-boost capability in a single conversion stage. This paper proposes the merging of the boost stage and the VSI stage in a single stage dc–ac power conversion, denoted as split-source inverter (SSI). The proposed topology requires the same number of active switches of the VSI, three additional diodes, and the same eight states of a conventional space-vector modulation. It also shows some merits compared to Z-source inverters, especially in terms of reduced switch voltage stress for voltage gains higher than 1.15. This paper presents the analysis of the SSI and compares different modulation schemes. Moreover, it presents a modified modulation scheme to eliminate the low frequency ripple in the input current and the voltage across the inverter bridge. The proposed analysis has been verified by simulation and experimental results on a 2.0-kW prototype. [ABSTRACT FROM PUBLISHER]

This paper investigates a multilevel inverter composed of series/parallel-connected H-bridges. The presented structure can be used for applications in which the use of semiconductor switches with low-voltage and low-current ratings is intended. A comprehensive system model, an overall control strategy to adjust the output voltage with constant magnitude and frequency, and a level-shifted PWM (LS-PWM) strategy based on a voltage vectors unidimensional analysis and a plane analysis are presented. The LS-PWM is capable of mitigating the low-frequency circulating current, thus generating multilevel voltage signals with low harmonic distortion, maximum number of levels, and low dv/dt. In addition, considering a wide range of values of voltages and currents and various power levels, the total converter losses are reduced compared with the conventional multilevel converters. Two multilevel conventional inverters with the same number of semiconductor switches are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

This paper proposes a single-phase, single-stage buck–boost inverter for photovoltaic (PV) systems. The presented topology has one common terminal in input and output ports which eliminates common mode leakage current problem in the grid-connected PV applications. Although it uses four switches, its operation is bimodal and only two switches receive high-frequency pulse width modulation signals in each mode. Its principle of operation is described in detail with the help of equivalent circuits. Its dynamic model is presented, based on which a bimodal controller is designed. Experimental results, in stand-alone and grid-connected mode, obtained with a 300-W laboratory prototype are presented to validate its performance. [ABSTRACT FROM AUTHOR]

A new single-phase \uppi-\texttype 5-level inverter using 3-terminal switch-network (3TSN) is proposed in this paper. The topology is considered as a variant of T-type 3-level structure or dual-buck inverter with coupled inductors. This new inverter is suitable for multilevel power inversion with low dc-bus voltage. The merit of the proposed topology is to apply only four active power switches to achieve 5-level operation. Other benefits include double frequency operation of output inductor and equal division of the current that flows through power switches and filter inductor. Hence, it leads to high efficiency and low harmonics. These characteristics allow improvement of losses distribution and volume reduction of output filter inductor. The operation scenario with sinusoidal pulsewidth modulation (SPWM) is described in details. Meanwhile, the magnetic analysis and design are studied and discussed. Finally, a prototype is built to verify the theoretical analysis and demonstrate the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

Carrier-based pulsewidth-modulation (CBPWM) techniques are popular due to their simplicity, and have been widely researched for various three-phase inverter configurations. In this paper, two CBPWM techniques are proposed to reduce the common-mode (CM) voltage generated by the five-phase inverter. The five-phase inverters have more flexibility in reducing the CM voltage than their three-phase counterparts because they have more phase legs, hence finer control over the star-point voltage of the load. Two methods are proposed for the conventional two-level five-phase inverter to reduce the CM voltage; one utilizing adjacent modulating waveforms and the other utilizing nonadjacent modulating waveforms. The coupled inductor inverter (CII) uses coupled inductors to generate multilevel outputs. As the volt-second balance must be maintained across each coupled inductor, direct application of the proposed methods on the CII inverter will result in overcurrents in the coupled inductors. Hence, the proposed methods are further improved to ensure the volt-second integral over each switching period is zero. Moreover, the two proposed methods are designed to reduce switching events and prevent unexpected states occurring during the switching transitions. The performance and the switching strategy of both methods are verified by both simulations and experiments on a prototype of five-phase CII. [ABSTRACT FROM AUTHOR]

This paper proposes the pulsewidth modulation (PWM) strategy of Z-source inverters (ZSIs) with minimum inductor current ripple. In existing PWM strategy with single-phase shoot-through, the shoot-through time interval is divided into six equal parts, therefore the three phase legs bear the equal shoot-through time interval. In this manner, the allotment and arrangement of the shoot-through state is easy to realize, but the inductor current ripple is not optimized. This causes to use relatively large inductors. In the proposed PWM strategy, the shoot-through time intervals of three phase legs are calculated and rearranged according to the active state and zero state time intervals to achieve the minimum current ripple across the Z-source inductor, while maintaining the same total shoot-through time interval. The principle of the proposed PWM strategy is analyzed in detail, and the comparison of current ripple under the traditional and proposed PWM strategy is given. Simulation and experimental results on the series ZSI are shown to verify the analysis. [ABSTRACT FROM PUBLISHER]

In this paper, a novel single-phase five-level inverter is proposed using coupled inductors. This inverter can output five-level voltage with only one dc source. No split of the dc voltage capacitor is needed, totally avoiding the voltage balancing problem in conventional multilevel inverters. The level of the output voltage is only half of the dc-link voltage in all conditions, leading to much reduced dv/dt . This inverter is based on the widely used three-arm power module and the voltage stresses on all the power switches are the same, making it very easy to construct. Operation mechanism of this inverter is analyzed and the possible switching patterns are investigated. Based on these analyses, a novel optimized modulation scheme is presented. With this modulation method, no dc components exist in the inductor currents, which is very helpful for minimization of the inductors. Simulation and experimental results show the validity of the proposed inverter together with the optimized modulation scheme. [ABSTRACT FROM AUTHOR]