Search

Voltage-controlled three-phase three-leg inverters are widely applied in various occasions. The inverters are generally switched to the current-controlled mode to limit the fault currents when short-circuit faults happen. Under symmetrical fault, the inverter can be controlled as a symmetrical, three-phase current source. However, the voltage limiting will happen under asymmetrical fault. As a result, the fault phase currents will be distorted and cannot be completely controlled. Considering that the voltage limiting is mainly caused by large load impedance of healthy phase under asymmetrical fault, the voltage limiting is avoided by paralleling the virtual impedance with the output filter capacitor in this paper. As a result, the current limiting loop is not broken and the fault phase currents can be effectively controlled. The implementation of virtual impedance in control system and the influence of virtual impedance on the stability of system are also analyzed in detail in this paper. The theoretical results are validated by experiments. [ABSTRACT FROM AUTHOR]

In photovoltaic systems, common-mode voltage (CMV) generates leakage current, which shortens the insulation lifespan and causes safety problems. As for neutral-point-clamped (NPC) inverters, zero CMV PWM (ZCMV PWM) can be implemented to eliminate leakage current, but unable to balance neutral-point (NP) voltage in dc side. This article presents a novel modulation technique for NPC PV inverter. The strategy contains ZCMV PWM and another two modulation modes which keeps CMV constant in one switching period, so as to eliminate leakage current. In order to balance NP voltage, NP current is adjusted by selection of optimal modulation mode and the leakage current is still well eliminated during the process of balancing NP voltage. Compared with conventional ZCMV PWM, the proposed scheme can remove both leakage current and NP voltage deviation. The output performance and limitations of the proposed method are also introduced in the paper. Experiments are provided to verify the validity of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a different Finite Control Set – Model Predictive Control (FCS-MPC) for grid-connected three-phase bidirectional power inverters. These are typically used in dc or ac renewable-based microgrids (MGs), where bidirectional operation and fast dynamic response is required. The bidirectional grid-connected inverters are an essential part of MG, which inject energy into the ac grid or demand energy from it. The dynamic behavior of the system is a major concern since the current can suddenly change depending on the hierarchical controller. This paper proposes a different cost function using sliding mode theory, which offers a good dynamic response, reduced computational burden, and a parameter-free control model. The operation principle of the proposed controller is given and evaluated using a Hardware-In-the-Loop (HIL) system, but also experimentally with a 1kW laboratory prototype. The final results demonstrate the advantages of using this approach in grid-connected three-phase bidirectional power inverters in terms of dynamic response and reduced computational burden, making this solution technically attractive and viable. [ABSTRACT FROM AUTHOR]

Conventional model predictive control (MPC) for three-level active neutral point clamped converter (ANPC) utilizes weighting factors to achieve the optimal control of multiple control objectives in a single cost function. However, the selection of these weighting factors has an impact on the performance of the controlled objectives significantly. Tuning of weighting factors is usually tedious and lacks theoretical background. Moreover, the predictive and evaluation process for multiple objectives optimization have to be carried out by enumerating all admissible switching states within one loop. To simplify the complexity of this process and eliminate the effect of weighting factors, this paper proposes a cascaded predictive control scheme for a 3L-ANPC inverter fed induction machine (IM) drive. With the proposed approach, three separate cost functions for three control objectives, stator flux vector, neutral point voltage and device loss distribution are evaluated in a cascaded way, so that the optimization of these control objectives is performed independently. A 3L-ANPC inverter driven IM drive is studied in this paper to verify the effectiveness of the proposed algorithm. Experimental results in different operating conditions confirm that the proposed method achieves satisfactory steady-state and transient performances comparable to the conventional predictive control approach. The weighting factors used in the conventional method are eliminated and the computational effort is reduced by 68% compared to the conventional method without any sacrifice in the drive performance. [ABSTRACT FROM AUTHOR]

The safety of converters is key to the stable operation of AC/DC hybrid power grids after AC faults. Thyristor valve current is a direct manifestation of the converter observability, but there are no measuring elements inside the converter, so the thyristor valve current can be reflected only indirectly through external electrical quantities. This paper proposes a virtual measurement scheme based on the temporal features of the converter terminal current. First, under the action of the trigger pulse, the polarity characteristics of the AC current and temporal features between the valves are utilized to predictive estimate the valve state. Then, when commutation failures occur and the bypass paths form, the conduction state of valve is constructed based on the relationship between AC and DC current. Last, when the valve is to be shut-off in the bypass path, the blocking state of the valve is corrected based on the unidirectional conductance characteristics of the valve. According to the above analysis, combined with the topological current equation of the converter, the valve current can be calculated in the whole process. Through the simulation of the different valve states and bypass paths and analysis of the field record data, the results show that the valve current can still be accurately calculated based on the virtual measurement scheme. [ABSTRACT FROM AUTHOR]

Most microgrid protection schemes found in published literature suffer from a lack of generality in that they work well for the assumed topology, including type and placement of sources. Other generic protection schemes tend to be too complicated, too expensive, or both. To overcome these drawbacks, a topology-agnostic, scalable, and cost-aware protection based on fundamental principles that work in the presence of high penetration of inverter-based resources (IBRs) is developed and tested in this paper. The protection system also implements stable automatic reconfiguration of the healthy sections of the system after clearance of fault, thus increasing resilience by self-healing. To achieve this ambitious goal, stable inverter models are developed that operate in unbalanced networks in grid-connected and islanded modes, even with 100% IBRs, share power without conflicting controls, and can ride through faults while limiting fault currents. The scheme is tested for primary and backup protection and reconfiguration on the IEEE 123-node feeder in grid-connected and islanded modes with 15 IBRs connected to the system. [ABSTRACT FROM AUTHOR]

This paper proposes a new passive Islanding detection approach for the Inverter Interfaced Distributed Generators (IIDGs) operating under different control modes. First, a novel index is formulated using Root Mean Square (RMS) value of the voltage and the frequency information, acquired at the Point of Common Coupling (PCC) of the target DG. The index is then post-processed by estimating the number of peaks and valleys $(N_{p_{k}-v})$ in a cycle using the sliding window concept, which indicates the occurrence of an event. Finally, the nature of the event, i.e., Islanding or non-Islanding, is decided by exploiting the two statistical features viz., Square of RMS $(S_{RMS})$ of $N_{p_{k}-v}$ and Average Crest Factor $(ACF^{m})$ of the proposed index. The performance of the proposed method (P-IDM) is demonstrated through comprehensive studies in PSCAD/EMTDC for the single-bus and IEEE 34-bus Active Distribution System (ADS). Also, the real-time validation is performed for the IEEE 34-bus using Controller Hardware-in-the-Loop (CHIL) setup comprising of Real-Time Digital Simulator (RTDS) and dSPACE1104. The simulation and hardware results for different test systems indicate that the proposed scheme, being generic in nature, sustains its efficacy under various interface controls of IIDGs. Finally, a comparative assessment with the other existing Signal Processing (SP) based passive methodologies shows the supremacy of the proposed method in terms of accuracy and faster detection. [ABSTRACT FROM AUTHOR]

Line-commutated converters are extensively used as the interface between ac grids and classic HVDC systems. At the inverter side, commutation failure of switches is one of the most common faults that can pose threats to the system operation. Practical and reliable study of such phenomena relies on accurate and efficient converter models for simulations. Recently, a parametric average-value model (PAVM) has been presented for ac–dc rectifiers, which considers the internal faults of the converter. In this paper, the PAVM methodology is extended to the dc–ac inverter systems, including the commutation failure of switches. The proposed PAVM also augments an automatic fault detection technique to determine the faulty switches. Using comprehensive simulation studies, the developed model is verified to accurately predict the commutation failure of switches and reconstruct the waveforms consistent with the detailed switching models of inverters while being computationally more efficient. The proposed PAVM is envisioned to be an efficient and accurate asset for simulation of HVDC systems and inevitable when faults of switches need to be considered. [ABSTRACT FROM AUTHOR]

Miniaturization and low cost contribute to the development and popularization of wireless power transfer (WPT). Reducing the number of power conversion stages can reduce the volume and cost of the WPT converter, and even make it possible to improve the efficiency. A single-stage WPT converter with constant current (CC) and constant voltage (CV) output and its asymmetric modulation method are proposed in this paper. A direct AC-AC converter is applied to the primary side of the WPT converter to directly convert line-frequency AC to high-frequency AC. The applied direct AC-AC converter that can replace the commonly used multi-stage primary converter reduces the number of circuit devices, thereby reducing the volume and cost of primary converter. The proposed WPT converter can realize zero voltage switching (ZVS) and power factor correction (PFC). In order to achieve CC and CV output, a switchable hybrid compensation topology is applied to the proposed WPT converter. A 720-W experimental prototype was manufactured to verify the rationality of the proposed WPT converter and the correctness of the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents a dual-hysteresis band control method for multi-drive systems based on a nine-switch inverter. The drive system contains two independent three-phase induction motors fed by a nine-switch inverter. Independent control of torque, speed, and stator current of two load stages is achieved. The proposed strategy offers a reliable control operation of both induction machines under individual load profiles. Instead of using independent sets of three-phase voltage source converters, the nine-switch inverter is used to drive separate machines. Thus, the volume and size of the power stage are noticeably reduced due to the use of fewer semiconductors. The theoretical concept and design steps of the proposed method are presented. The performance of the closed-loop independent motor control scheme is experimentally validated using a 3.2 kW lab-scaled nine-switch inverter prototype and Altera Cyclone IV Field-programmable gate array. [ABSTRACT FROM AUTHOR]

This paper proposes a novel polygonal voltage space vector structure (SVS) having 30 sides, for a star-connected induction motor drive. The SVS eliminates the presence of harmonics up to 25th order from motor phase voltage throughout the entire modulation range, providing a torque profile devoid of lower order pulsations. Linear modulation is extended till 99.63% of base speed without exceeding the motor phase voltage rating. Topology consists of a dc-link fed primary inverter and two equal low voltage modular capacitor fed secondary inverters. Here the harmonics generated by the primary inverter is canceled by the secondary inverter which acts as a switched capacitive filter. Detailed description of the SVS generation and timing calculations are provided in this paper. Effectiveness of the proposed scheme is validated using experimental results, inverter loss calculations, and harmonic analysis. [ABSTRACT FROM AUTHOR]

Four-level hybrid-clamped inverter is a newly proposed topology that can operate under a wide voltage range without switches connected in series. However, when it is applied in medium voltage high power conversions, the flying capacitors in each phase will occupy a huge volume and a high switching frequency is required to restrain the voltage ripples. In order to overcome this drawback, a four-level active neutral-point clamped inverter is discussed in this paper, which consists of only six switches and no diodes or flying capacitors are required. In order to balance the neutral-point voltages under the full power factor and modulation index range, a capacitor voltage balance method based on carrier-overlapped pulsewidth modulation is proposed in this paper. The upper and lower dc-link capacitor voltages are balanced by zero-sequence voltage injection and the central dc-link capacitor voltage is balanced by adjusting the duty cycles of switching signals slightly. Simulation and experimental results are presented to confirm the validity of this method. [ABSTRACT FROM AUTHOR]

This paper presents an optimization method for selective harmonic elimination in a cascaded multilevel inverter using teaching–learning-based optimization (TLBO). The main objective in selective harmonic elimination (SHE) strategy is to eliminate low-order harmonics by solving nonlinear equations and reaching optimal solution, while the fundamental component is satisfied. In this paper, in one side, the influence of optimal dc sources is investigated to reach the SHE goal, and in another side, comparing optimization methods is considered. In this paper, the TLBO as a recently emerged nature-inspired algorithm is presented to provide better results for the SHE in comparison with genetic algorithm, artificial bee colony, imperialistic competitive algorithm, harmony search, ant colony optimization, particle swarm optimization, and differential evolution. For better comparison of those methods and influence of optimal dc sources, 5-, 9-, and 15-level inverters are chosen and MATLAB software is used for optimization. Simulation results show the superiority of TLBO, higher precision and probability of convergence than other mentioned algorithms. Finally, to validate the influence of optimal dc sources and the accuracy of TLBO results, the experimental setup is conducted for a 5-level cascaded H-bridge inverter with optimal dc sources. [ABSTRACT FROM AUTHOR]

This paper presents a 5-level inverter topology for open-end induction motor drives by using a single dc source. The open stator windings of the drive are supplied with a 3-level flying capacitor inverter from one end and capacitor-fed 2-level inverter from another end. The voltage ratio of the dc link to the capacitor in 2-level inverter is maintained at 4:1 ratio to generate five-level voltage output. The capacitor in 2-level inverter is balanced by the switching redundant vector combinations from both the inverters while the floating capacitors in the 3-level inverter are balanced by using redundant switching states. The proposed topology gives 5-level operation with less number of floating capacitors and power semiconductor switches compared to other existing topologies. Also, the balancing of the capacitors is independent of load power factor and modulation index. Further, the generalization of the proposed dual inverter scheme for any n-level inverter is also included in this paper. The experimental results and required analysis are also presented to validate the inverter scheme. [ABSTRACT FROM AUTHOR]

This paper presents the development of a Class-D full-bridge zero-voltage switching (ZVS) inverter, applicable to wireless power transfer (WPT) systems, operating at 13.56 MHz switching frequency with dynamic dead-time control (DDTC). Resonant-coupled WPT systems are being designed at ultrahigh switching frequencies to reduce the size of the wireless link and the passive components. Maintaining ZVS while controlling the output power delivered to a fixed or variable load is one of the major challenges of designing inverters at multi-MHz switching frequencies. DDTC is the approach deployed in this paper to sustain soft switching of a Class-D full-bridge inverter over the full range of output power while regulating the input dc bus voltage. Simulation results are presented to show that dynamically controlling the dead-time during input dc bus voltage variations reduces switch-node voltage overshoot, prevents large current spikes in the switching devices, and reduces associated high switching loss. Practical results obtained show that DDTC reduces switch-node voltage overshoot, increases the inverter efficiency, and reduces the steady-state temperature of the inverter during output power regulation. [ABSTRACT FROM AUTHOR]

First harmonic analysis (FHA) is arguably the most widely used analytical technique for wireless power transfer (WPT) circuits due to its simplicity. Although FHA can provide closed-form solutions, the existence of rectifier diode forward voltage drop and higher order harmonics, especially the second and third harmonics at variable duty cycle operation, can significantly deteriorate its accuracy. This paper presents an accurate and efficient method called enhanced multiple harmonic analysis (eMHA) for the optimal design and optimal control of WPT systems. The eMHA method considers the nature of nonlinear rectification networks under nonsinusoidal current and reexamines the concept of the equivalent load. As a result, the rectified WPT system is transformed into a series of linear systems with complex load impedances. The steady-state electric quantities can be then explicitly calculated. This enables eMHA to seamlessly work with numerical optimization algorithms to facilitate the automated design and optimization of WPT systems. An example of optimal design and optimal control of a 10 W WPT system is demonstrated. The results obtained by eMHA and FHA are also compared. A prototype of the designed circuit was constructed. The accuracy and effectiveness of eMHA are verified by experimental measurements. This paper is accompanied by a MATLAB-based analytical tool with a graphical user interface demonstrating the effects of circuit variables on electrical quantities and waveforms. [ABSTRACT FROM AUTHOR]

In this paper, a new modular and active snubber cell, easily applicable, and attractive for converters, especially have many switches proposed. This snubber cell is implemented on the single phase of a grid-connected three-phase T-type three-level inverter (T-3LI). In this new converter, the main switches turn-on under zero-voltage transition and turn-off under zero-voltage switching (ZVS). Also, auxiliary switches turn-on under zero-current switching and turn-off under ZVS. All snubber diodes operate under soft switching (SS). There are no additional current and voltage stresses on the main switches. During an SS operation, the switching energies are transferred to a dc voltage source. Then, these energies are processed to input with an independent dc–dc converter. Thus, all switching energies are recycled. In this paper, the principle operation and steady-state analysis of the modular and active snubber cell for a single-phase T-3LI are presented and experimental results, rated 1 kW and 100 kHz, are provided to verify theoretical analysis. [ABSTRACT FROM AUTHOR]

The paper confirms that removing antiparallel silicon carbide (SiC) Schottky barrier diodes (SBDs) from SiC-based inverters offers positive effects without critical impact on inverter loss and electromagnetic interference (EMI) issues, moreover, the removal of SBDs reduces the inverter losses in many cases and noise emissions. This conclusion leads to the possibility to improve the power densities by removing SBDs. However, the removal of SBDs may cause some disadvantages such as an increase of the reverse conduction loss and influence of the body diode recovery phenomenon. Therefore, a comprehensive investigation of these advantages and disadvantages is necessary. In this paper, design criteria are proposed to clarify the conditions in which SiC-based inverters without SBDs have advantages over those with SBDs from the viewpoint of losses. On the other hand, to achieve the removal of SBDs, it is also necessary to confirm that removing SBDs does not cause severe EMI issues. The paper confirms that switching noises are reduced by the removal of SBDs; this is due to the larger damping effect of the SiC mosfets without SBDs than that of SiC mosfets with SBDs. The validity of the theoretical analyses and design criteria is confirmed with comprehensive experimental results. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

A space vector modulation (SVM) technique of a dual-inverter system for an open-end winding motor drive is described in this paper, where one inverter has a battery power source and the other has an only capacitor across the dc bus. The SVM must be achieved to operate the motor with field-oriented control and simultaneously to control the capacitor voltage at a constant value by using redundant switching states of the dual-inverter system. The control of the capacitor voltage is carried out by selecting a charging or a discharging mode in each redundant switching state, taking the instantaneous motor power factor into account. In addition, it is also required to reduce the error voltage pulses, which are generated in output multilevel voltage waveforms during the dead time. The compensation method of the existing dead-time scheme and the improved SVM sequence to reduce the error voltage vectors are proposed in this paper. The proposed methods are examined through several experimental tests and are confirmed to generate superior output voltage waveforms from the viewpoint of the measured total harmonic distortion and dv/dt. [ABSTRACT FROM AUTHOR]

The main drawbacks of conventional direct torque control (DTC) drives are erratic switching frequency and high torque ripples. The multilevel inverter fed DTC drives are proved to be an alternative for eliminating these drawbacks. Apart from the commonly used three-level inverter fed drives, this paper presents an even-level inverter fed DTC drive. In this paper, a space vector modulated DTC algorithm for a four-level DTC drive is proposed and is implemented by feeding both ends of an open-end-winding induction motor with two-level inverters. The space vector modulation (SVM) algorithm uses a fractal based design for switching voltage vector generation and allied computations are performed in 60 degree co-ordinate system. Representation of vectors as integer values in 60 degree co-ordinate planes avoids fractional arithmetic, which simplifies the algorithmic computations. Detailed analyses of the drive performance under dissimilar operating modes are presented. The loading performance of the drive is experimentally verified on a 5-HP induction motor with a strain gauge type mechanical loading system. No-load experimental results were obtained from a laboratory model 2-HP induction motor drive operated in closed loop mode. [ABSTRACT FROM AUTHOR]

This paper proposes a resonant switching cell model to analyze and design the single-ended resonant dc–dc converters. The single-ended zero-voltage switching (ZVS) converters such as the Class E converter are efficient for megahertz switching because they feature low turn-on and turn-off switching losses. Also, they use only a ground-referenced switch, allowing a simple gate drive circuit. In this paper, we investigate the single-ended resonant converter with the small input inductance, whereas the conventional Class E converter has a large input inductance. The main contribution of this paper is to propose the resonant switching cell as an analytic model that simplifies the analysis and the design of the resonant dc–dc converters. Furthermore, this paper presents the design method of the resonant switching cell model for minimizing the resonant current magnitude and conduction loss while the converter maintains ZVS property. The experimental results from a 10-MHz GaN-based prototype demonstrate the feasibility and effectiveness of the analysis and design based on the proposed resonant switching cell model. [ABSTRACT FROM AUTHOR]

Multilevel inverters (MLIs) are playing a pivotal role in the power sector with potential applications, such as interfacing renewable energy sources with the grid and several industrial drive applications. MLIs with a smaller number of switching devices are more promising due to their compact size, reduced cost, and higher efficiency compared with their traditional counterparts. This paper, therefore, presents a new three-phase seven-level inverter. This topology is a combination of two cascade-connected two-level voltage-source inverters (VSIs) and H-bridge cells with flying capacitors (FCs). This paper presents the operating principle and the balancing technique for the dc-link capacitors and FCs. The generation of various output voltage levels and the limitation of the sinusoidal pulsewidth modulation control for FC voltage balancing is also presented. The number of components in the proposed circuit configuration and their voltage ratings are considerably lower compared with the recently proposed topologies. The behavior of the proposed circuit configuration is first assessed with simulation studies and is then tested with a laboratory prototype. The simulation and experimental results validate the effectiveness of the proposed topology and the voltage balancing technique. [ABSTRACT FROM AUTHOR]

In this paper, an overload and short-circuit protection method is proposed for voltage source inverter-based uninterruptible power supply (UPS) system. In order to achieve high reliability and availability of the UPS, short circuit and overload protection scheme are necessary. When overload or short circuit happens, using the proposed control method, the amplitude of the output current can be limited to a constant value, which can be set by the customer to avoid the destruction of the power converter, and to obtain a faster recovery performance as well. The detailed principle of the proposed protection method is discussed in this paper. It mainly contains three parts in the control diagram for current limit, first is the anti-windup in the voltage and current controllers, then the feedforward of the capacitor voltage to the current control loop, the last is the fast reset of the resonant part of the current controller when overcurrent happens. The procedure of developing the control method is also presented in the paper. Experimental results on a commercial UPS system are presented to verify the effectiveness of the control method. [ABSTRACT FROM AUTHOR]

This paper presents a novel seven-level inverter topology for medium-voltage high-power applications. It consists of eight active switches and two inner flying capacitor (FC) units forming a similar structure as in a conventional active neutral-point-clamped (ANPC) inverter. This unique arrangement reduces the number of active and passive components. A simple modulation technique reduces cost and complexity in the control system design without compromising reactive power capability. In addition, compared to major conventional seven-level inverter topologies, such as the neutral point clamped, FC, cascaded H-bridge, and ANPC topologies, the new topology reduces the dc-link voltage requirement by 50%. This recued dc-link voltage makes the new topology appealing for various industrial applications. Experimental results from a 2.2-kVA prototype are presented to support the theoretical analysis presented in this paper. The prototype demonstrates a conversion efficiency of around 97.2% ± 1% for a wide load range. [ABSTRACT FROM AUTHOR]

Multilevel inverters (MLIs) are being used in wide range of power electronic applications. These converters have attracted a lot of attention during recent years and exist in different topologies with similar basic concepts. This paper presents five main submodules (SMs) to be used as the basic structures of MLIs. The paper reviews the common MLI topologies from the structural point of view. The topologies are divided into the different SMs to show conventional MLI configurations and future topologies that can be created from the main SMs. A comparative study between different topologies is performed in detail. The MLIs are categorized and investigated with from different perspectives such as the number of components, the ability to create inherent negative voltage, working in regeneration mode and using single dc source. [ABSTRACT FROM AUTHOR]

Reduced switch active phase converters (APC) are cost-effective solutions for running three-phase loads from single-phase grids. This paper proposes a novel auxiliary-capacitor-based APC (AC-APC) for this application. The combination of the topological location of the auxiliary capacitor and the control of the AC-APC reduces current stress on the semiconductor devices. In this paper, a selection criterion for the optimal auxiliary capacitor value is formulated to reduce the device currents in such a way that the overall efficiency is enhanced. This paper presents a comparative analysis of converter volt-ampere (VA) rating and device power loss for conventional H-bridge active front-end and inverter-based topology, APC, and AC-APC. To evaluate the efficacy of the proposed AC-APC, an experimental study is conducted on the APC and the AC-APC feeding a 3-hp three-phase induction motor. At a full load of $\text{2.5}\,\text{kW}$ and $\text{0.8 } \text{power factor}$ , the measured maximum efficiency of the AC-APC is $2\%$ higher than that of the APC. Analytical evaluation of converter currents and device power loss are in close agreement with experimental observations. [ABSTRACT FROM AUTHOR]

The supply-side current of an inverter-fed induction motor (IM) is easily accessible and less affected by noises than the motor stator current. This paper proposes a novel sensorless speed estimation method for an IM using the spectrum of the supply-side current. However, due to the influence of fundamental supply frequency, it is difficult to carry out the speed detection straight from the supply-side current signal. In this paper, an analytic model for characterizing the supply-side current of an inverter-fed IM using the modulation theory and the switching function concept is developed. Then, the Hilbert transform is applied to extract the speed harmonic component from the supply-side current. Finally, an interpolated Goertzel algorithm is put forward to enhance the estimation precision of IM speed. The performance of the proposed sensorless speed estimation method is proved by the speed estimation results obtained from hardware experiments of an IM fed by an inverter under different load conditions. [ABSTRACT FROM AUTHOR]

In low-power applications of photovoltaic (PV) systems, the transformerless grid-connected inverters have been preferred to increase the efficiency and reduce the cost, size, and power losses when they are compared to the ones with the transformer. A transformerless single-phase inverter topology with a single dc-link capacitor for the grid-connected PV systems is proposed in this paper. The proposed inverter has been simulated by using a cooperation process of the MATLAB and SPICE package programs and it has been implemented for experimental verification. The proposed inverter reduces the high-frequency common-mode leakage current caused by parasitic capacitances of PV panels, whereas it is controlled with the unipolar sinusoidal pulsewidth modulation. Also, the results show that the common-mode voltage remains constant. The efficiency of the proposed inverter has been compared to that of the most common topologies having the dc-link decoupling during the zero voltage states. This paper is accompanied by a video file demonstrating the power loss distribution in the inverter. [ABSTRACT FROM AUTHOR]

This paper describes a dc-link voltage control method of a single-phase back-to-back cascaded H-bridge inverter (SBCI) for a medium-voltage motor drive system. The main advantage of the SBCI topology over the conventional regenerative cascaded H-bridge topology with a three-phase active front-end (AFE) is a simple system structure, which is composed of an input transformer, a power cell, a current sensor, etc. However, the challenging points of the SBCI are larger voltage ripple in the dc-link capacitor and imbalance of dc-link voltages of each phase. The asymmetric dc-link voltage of each power cells could cause unstable operation such as over-modulation due to the lack of the dc-link voltage of a particular phase and result in over-voltage or under-voltage faults. In this paper, the control strategy of the dc-link voltage for the SBCI that uses the negative-sequence voltage of the converter is described. The proposed control method is verified with a computer simulation whose target is a 6.6-kV–1.25-MW medium-voltage drive system. Also, through the experimental setup with the prototype SBCI whose power rating is 16.2 kVA, the dc-link voltage of each AFE has been controlled within a 0.5% error of its reference value at the full load. [ABSTRACT FROM AUTHOR]

This paper presents a new single-source three-phase seven-level inverter with an inherent three-time voltage boosting capability for medium-voltage applications. The proposed topology is comprised of series connection of two switched-capacitor (SC) networks with an added half-bridge module per phase. Each of such integrated SC networks requires a single capacitor associated with three active power switches. The three-time voltage boosting feature of the proposed topology can reduce the dc-link voltage requirements by 50% in comparison to the traditional neutral point clamped (NPC), flying capacitors, active NPC (ANPC), hybrid clamped ANPC, and cascaded H-bridge topologies, and 75% to advanced ANPC topologies. It can also reduce the number of required switches and capacitors as well as their voltage stresses compared to those state-of-the-art topologies reported in the literature. By integrating “n” number of added SC networks in the proposed seven-level basic topology, the number of output voltage levels can be extended to 2n+3 per phase. A finite control set model predictive control algorithm is also derived to control the converter in both the active and reactive power exchanges modes without distorting the generated grid current quality. The capacitor voltage balancing is inherent in the proposed topology, and thus, there is no need for any additional voltage balancing circuit, which further reduces the control complexity. The performance of the proposed topology and its control algorithm are validated by several measurement results. [ABSTRACT FROM AUTHOR]

In a line-commutated converter based high-voltage direct-current (LCC-HVDC) system, the inverter control system usually includes constant extinction angle (CEA) controller, constant current (CC) controller, current error controller (CEC), and voltage-dependent current order limiter (VDCOL). However, the interaction influence of multiple controllers may cause repetitive commutation failure (CF). For this purpose, this paper deeply investigates the mechanism and the influencing factors of repetitive CF caused by controller interaction. It is found that the lower limit value of CEA controller can affect the control switching process and thus the probability of repetitive CF. Besides, the minimum gamma measurement (MGM) unit prevents the system from acquiring the real extinction angle in time, which results in the DC current fluctuation during the recovery process. Moreover, the probability of control-induced repetitive CF is much higher when the HVDC inverter is connected to a weak AC system or the AC fault is not serious but not cleared in time. Based on the above analyses, an improved control method is proposed for recovery performance improvement, which is mainly realized by modifying the lower and upper limits of the CEA controller during recovery. Finally, the simulation and experimental results verify the theoretical analyses and the proposed control method. [ABSTRACT FROM AUTHOR]

Motors and inverters are increasingly being used in vehicles. As more vehicle components are being adopted, requirement for safety and installation space are increasing. Growing attention is being paid to the use of six-phase permanent magnet synchronous motors (PMSMs) and their parallel control by two inverters, because of their reduced size and enhanced safety. This paper proposes a pulsewidth modulation (PWM) control algorithm for a six-phase PMSM. In low-voltage vehicle components such as electric power steering, the current is usually acquired with resistors placed under the low-side switching devices. In the proposed control algorithm, the neutral voltage of the two inverters is shifted to either a lower or higher voltage within a certain range to allow for the signal conditioning time delay after the switching device turns on or off, and the time taken for the phase current to rise or settle. The paper proposes a novel PWM control algorithm that ensures that the on-time of the low-side switching devices satisfies the restriction on current sensing with resistors and reduces the current in the capacitor at the same time. The work contributes to reducing the current in a practical configuration involving low-voltage vehicle components. [ABSTRACT FROM AUTHOR]

The huge untapped energy from ocean waves is one of the ideal solutions for world energy crisis. This paper proposes a linear-generator-based direct power conversion plant model to generate the electrical energy from ocean waves. The linear generator output is of variable magnitude and variable frequency in nature. In this paper, this variable output is converted to fixed dc voltage by using a diode bridge rectifier and a dc-link capacitor. The linear generator along with a diode bridge and a capacitor forms a wave power unit. These wave power units can be connected in series and parallel to meet the power ratings. A reliable multilevel inverter is fed from the wave power units to ensure uninterrupted tapping of power from this abundant renewable energy source. The reliable inverter operation is analyzed under open- and short-circuit faults in switches by reconfiguring the carrier waves of sine pulsewidth modulation during fault conditions. A fault detection algorithm using a single sensor at the output is also proposed to detect the faults in the switches of the proposed reliable inverter. The proposed plant model with a linear generator and a reliable inverter is simulated using ANSYS MAXWELL and MATLAB/Simulink. The plant model is tested using a programmable ac source for emulating the linear generator and the developed prototype of the diode bridge rectifier and the reliable multilevel inverter. [ABSTRACT FROM AUTHOR]

The planned China fusion engineering test reactor (CFETR) needs one or more negative-ion-based neutral beam injectors (N-NBIs) with a beam energy of 500 or even 1000 keV. In order to prepare for CFETR, a prototype of CFETR N-NBI is being designed. The prototype needs an acceleration grid power supply (AGPS) rated at 200 kV/25 A with a maximum pulselength reaches to 3600 s. The AGPS adopted a single-stage inverter-type high-voltage power supply (HVPS). The output voltage ripple is an important specification of the AGPS, which can affect the efficiency and stability of N-NBI system by influencing the beam divergence. However, the conventional methods cannot be used to limit the output voltage ripple of the inverter-type HVPS used as AGPS of CFETR N-NBI prototype. This paper simplified the AGPS to an insulated three-phase three-level (TPTL) dc–dc converter connected with a dual dc link. The working process of the TPTL dc–dc converter with duty-cycle modulation has been analyzed, and two main continuous conduction modes are described. The influence of key parameters such as duty cycle of inverter, leakage inductance of transformer, and output current on output voltage ripple is analyzed. Based on the analysis results, a so-called combined control strategy was proposed to keep the output voltage ripple at a level. The proposed strategy is suitable for the cases where the object output voltage is below 175 kV. Some simulations were carried out by using MATLAB/Simulink. The results showed that the analysis in this paper is reliable and the proposed control strategy has a good performance. [ABSTRACT FROM AUTHOR]

Enhancement of dc bus voltage utilization for a five-level inverter with single dc source and capacitor-fed H-bridge (CHB) units is investigated in this paper. A carrier-based modulation technique is used for boosting the dc bus utilization, which is established by providing detailed mathematical analysis. The five-level inverter used here is realized by cascading a CHB unit to each phase of a three-level neutral point clamped inverter. The increase in dc bus voltage utilization owes to the pole voltage redundancies offered by CHB units. The floating capacitors of H-bridge units are balanced within a quarter fundamental cycle using the switching state redundancies of pole voltage levels. The aforementioned modulation technique allows the inverter to enhance the dc bus utilization from 0.577 $\text{V}_{\text{dc}}$ to 0.63 $\text{V}_{\text{dc}}$ under unity power factor. This enhancement is obtained in the linear modulation range without increasing the dc bus voltage, and thus, the inverter can operate without the presence of low-order harmonics in its phase voltages. The strength of this paper lies in its detailed mathematical analysis for finding out the limiting modulation index and power factor condition in the light of floating capacitor voltage balancing issue. Simulation as well as experimental verification of the modulation scheme is carried out on an induction motor drive under various operating conditions. It is shown that this carrier-based modulation technique is suitable for any single source inverter topology with one CHB unit per phase. [ABSTRACT FROM AUTHOR]

This paper proposes a novel method for instantaneous balancing of neutral-point (NP) voltages with stacked multilevel inverters (MLIs) for variable-speed drives. The stacked MLI uses series-connected dc sources and NPs (connecting points of dc sources) to obtain the desired levels. The balancing of NP voltages are obtained by using a low-voltage-capacitor-fed cascaded H-bridge (CHB) per phase of a symmetrical six-phase induction machine (IM), which ensures zero current drawn from NPs (at any given instant). Since no current is drawn from NPs, the single dc-link operation with stacked capacitors is also possible. The scheme is suitable for applications, where low-voltage dc sources and batteries are stacked to form a dc link. A variable-speed operation is done using a seven-level inverter scheme for a symmetrical six-phase IM, which is formed by three dc-link stacked capacitors cascaded with two low-voltage-capacitor-fed CHBs per phase. Furthermore, the method is extended for an open-end IM to obtain a seven-level common-mode eliminated space vector structure using a single dc link. The generalization of this method for any stacked $n$ -level inverter without NP voltage deviation is also presented in this paper. The experimental results and analysis are included to validate the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a novel single-stage soft-switched high-frequency-link three-phase dc–ac converter topology. The topology supports unidirectional dc to ac power flow and is targeted for applications like grid integration of photovoltaic sources, fuel cell, etc. The high frequency magnetic isolation results in reduction of system volume, weight, and cost. Sine-wave pulsewidth modulation is implemented in dc-side converter. Though high-frequency switched, dc-side converter is soft switched for most part of the line cycle. The ac-side converter active switches are line frequency switched incurring negligible switching loss. The line frequency switching of ac-side converter facilitates use of high voltage blocking inherently slow semiconductor devices to generate high voltage ac output. In addition, a cascaded multilevel structure is presented in this paper for direct medium-voltage ac grid integration. A detailed circuit analysis considering nonidealities like transformer leakage and switch capacitances, is presented in this paper. A 6-kW three-phase laboratory prototype is built. The presented simulation and experimental results verify the operation of the proposed topologies. [ABSTRACT FROM AUTHOR]

Soft magnetic powder cores with their high saturation flux density and low core loss are excellent alternatives for filter inductors in inverter-based applications. However, their nonlinear current-dependent inductance characteristics pose a challenge for control of grid-connected inverter with LCL filter. In this paper, the variable inductance conundrum is discussed and a modified direct digital control method based on a variable-structure inductance estimation model that takes into consideration wide nonlinear variation in both inverter- and grid-side inductances is proposed. The proposed method is shown to have better grid-voltage harmonic rejection and improved stability margins. However, investigation of stability which is conventionally based on nominal values of filter inductors cannot predict instabilities over the entire range of inductance variation. Hence, a parametric approach to conventional stability methods with a parameter space defined by variation in actual and estimated inductance is explored in this paper. The effect of line impedance on stability is also investigated with impedance-based stability criterion by considering line inductance as an additional dimension in the parameter space. A pattern in stability margins is observed due to inductance variation, with inductance at its minimum being most vulnerable to instability. Experimental results measured from a 5 kW single-phase grid-connected inverter with various LCL filters have verified the feasibility of the proposed control method. The experimental results also match the analytical results with reasonable accuracy. [ABSTRACT FROM AUTHOR]

This paper proposes a new dc–ac converter with a reduced number of semiconductor switches and gate drive and control circuit components. A salient feature of this inverter is its pure sinusoidal line-to-line voltages with no need for output filter. Also, the proposed inverter improves the voltage utilization factor of the input dc supply compared to the four-switch three-phase inverter (first best topology in the literature from the number of switches point of view) and standard six-switch inverter with sine pulsewidth modulation. The proposed inverter is capable of operating with a wide range of output voltages from zero to the full value of the dc input voltage by appropriately altering the instantaneous duty cycle. A three-phase universal inverter with only three power switch has been proposed in this paper for the first time ever, to our knowledge. For the purpose of providing a good compromise between fast transient response and stability, a model predictive controller is proposed. All the design expressions have been derived. A comparison with other dc–ac converters is given to show the merits of the proposed converter. Finally, satisfactory circuit operation is confirmed by experimental results from a laboratory prototype. [ABSTRACT FROM AUTHOR]

This paper proposes a high-efficiency single-phase T-type boundary conduction mode (BCM) microinverter. The conventional full-bridge BCM microinverter has achieved zero voltage switching (ZVS) and thereby improved the efficiency, but it suffers from high switching losses under light load conditions. The proposed T-type BCM microinverter reserves ZVS and uses a multilevel technique to further decrease the switching losses. The BCM operation with multilevel technique will have too low switching frequency when the grid voltage approaches half of the dc link voltage. To solve this problem, this paper adopts a third operation mode for the T-type switching leg to maintain the switching frequency above a minimum value. The corresponding mode transitions are also detailed to ensure a smooth operation. Because of the turn-offdelay of the freewheeling transistor, the actual lower current boundary deviates from the programmed one, which will distort output current. To address this issue, this paper also proposes a boundary compensation method. A prototype has been built for performance verification, which can test both full-bridge and T-type topology. Compared with the full-bridge BCM microinverter, the proposed T-type BCM microinverter has a higher efficiency over the whole load range. [ABSTRACT FROM AUTHOR]

This paper presents the digital implementation of a boundary controller with unipolar switching characteristic for single-phase voltage source full-bridge inverters. This paper expands the application of a second-order switching surface-based control method to unipolar switching of single-phase voltage source inverters (VSIs) using a finite-state machine. The finite-state machine has been formulated considering four different states of the inverter; positive,zero1, negative, andzero2. The second-order boundary control governs the current state of the system and provides proper switching action to keep the system within the desired reference. The control law is implemented digitally in F28m35x digital control card. A full-bridge inverter topology is used to achieve the three-level voltage switching. Various simulations and experiments were performed in a 550 VA, 120 V, 60 Hz VSI with a digitally implemented controller to verify the theoretical predictions. A high-quality voltage output was obtained for various loading conditions. The transient performance of the controller was investigated using a reference and load changes. A comparison of the implementation was made with the existing classical controllers to verify the fast-dynamic response of the system. [ABSTRACT FROM AUTHOR]

Soft-switching techniques of transformerless photovoltaic grid-connected inverters (TLIs) can significantly reduce switching losses, as well as soften switching processes. Conventional dc–ac soft-switching configurations proposed by Dr. Deepakraj M. Divan are invalid in TLIs because of the leakage current problem. In order to develop soft-switching techniques in TLIs, this paper proposes a new soft-switching configuration and a procedure to guide the invention of soft-switching TLIs. First, this paper proposes two basic resonance tanks related to dc bus polarities, and then, uses these basic tanks to elevate four popular full-bridge-type TLIs according to the proposed guideline. As a result, four soft-switching TLIs are gained. Second, this paper picks obtained soft-switching highly efficient and reliable inverter concept (HERIC) as example to analyze its soft-switching operation principle and performance. As a consequence, all active switches of the gained soft-switching HERIC circuit are switched under both of zero-current turn-on and turn-off conditions; the reverse recovery problem of freewheeling diodes is alleviated owing to the zero-current turn-off of diodes; meanwhile, the common-mode voltage at the switching frequency scale is still constant. Finally, some experimental results from a 3-kW universal prototype at 50-kHz switching frequency are provided to verify the effectiveness of the main contributions of this paper. [ABSTRACT FROM AUTHOR]

This paper proposes a novel discontinuous pulse-width modulation (DPWM) method to reduce the current harmonics and improve the system efficiency for a single-phase three-level neutral-point clamped inverter. In single-phase inverters, the unipolar pulse-width modulation (UP-PWM) method is commonly used. However, this method has the disadvantage of power losses due to numerous switching operations. Conventional DPWM methods reduce the power losses and improve efficiency but increase the current total harmonic distortion (THD). To overcome these weaknesses, this paper proposes a hybrid DPWM switching method combining two PWM methods: the UP-PWM method and the conventional DPWM method called one-pole clamped PWM method. Since the proposed DPWM method offers all the advantages of both PWM methods, the optimal performance—with regard to the power losses and current THD—is obtained. The combination of two PWM methods is investigated by analyzing the power losses and current THD. Based on the analysis, the process determining the optimal operating condition is introduced. The effectiveness of the proposed DPWM method is demonstrated through simulations and experiments. [ABSTRACT FROM AUTHOR]

This paper proposes a new high-efficiency photovoltaic (PV) converter for grid connection through a high-leg delta transformer. The converter is composed of a symmetrically connected boost converter and three half-bridge inverters. One of the three half-bridge inverters is connected to the boost converter, and the others are directly connected to the PV terminals. As a result, this circuit configuration enables to reduce the power losses in both boost converter and inverters. This paper also proposes a new cooperative control method between the symmetrically connected boost converter and inverter. The control method can reduce the average switching frequency to 75% of that in a conventional one, resulting in a great reduction in the switching power loss. Experimental results confirm that the proposed circuit configuration makes it possible to improve its European efficiency from 91.6% to 94.5%. Moreover, system performance is evaluated on the assumption of maximum power point tracking operation. [ABSTRACT FROM AUTHOR]

This paper presents a unified framework for the modeling, analysis, and design of load-independent Class E and Class EF inverters and rectifiers. These circuits are able to maintain zero-voltage switching and, hence, high efficiency for a wide load range without requiring tuning or use of a feedback loop, and to simultaneously achieve a constant amplitude ac voltage or current in inversion and a constant dc output voltage or current in rectification. As switching frequencies are gradually stepping into the megahertz (MHz) region with the use of wide-bandgap (WBG) devices such as GaN and SiC, switching loss, implementing fast control loops, and current sensing become a challenge, which load-independent operation is able to address, thus allowing exploitation of the high-frequency capability of WBG devices. The traditional Class E and EF topologies are first presented, and the conditions for load-independent operation are derived mathematically; then, a thorough analytical characterization of the circuit performance is carried out in terms of voltage and current stresses and the power-output capability. From this, design contours and tables are presented to enable the rapid implementation of these converters given particular power and load requirements. Three different design examples are used to showcase the capability of these converters in typical MHz power conversion applications using the design equations and methods presented in this paper. The design examples are chosen toward enabling efficient and high-power-density MHz converters for wireless power transfer (WPT) applications and dc/dc conversion. Specifically, a 150-W 13.56-MHz Class EF inverter for WPT, a 150-W 10-MHz miniature Class E boost converter, and a lightweight wirelessly powered drone using a 20-W 13.56-MHz Class E synchronous rectifier have been designed and are presented here. [ABSTRACT FROM AUTHOR]