Search

In order to achieve the purpose of extending the speed range and reducing power electronics devices for the permanent-magnet linear motor drive system, a half-centralized open-end winding (OEW) topology is studied for rail transit applications in this paper. In this topology, compared with the traditional OEW topology, the number of voltage-source-inverters (VSIs) can be reduced from four to three to drive two OEW movers and all these VSIs share a common dc bus voltage. In order to improve the steady-state performances, a four-vector phase model predictive voltage control (FV-PMPVC) is proposed in this paper. Due to the spatial distribution of phase voltage vector (PVV), an orthometric synthesis principle (OSP) is proposed to calculated the duration time for the vector synthesis, which reduces the computation burden and enhances the robustness. Comparing the existing control method, FV-PMPVC can get similar dynamic performances but better steady-state performances. Additionally, the half-centralized topology using FV-PMPVC can have same speed range while less VSIs are required. The effectiveness of FV-PMPVC is verified by experimental results. [ABSTRACT FROM AUTHOR]

In renewable energy micro-source applications, a wide range of voltage conversion of the step-up converter is an essential part to equalize the typical low voltage of micro-source with DC-bus voltage of Inverter or motor drives. In order to meet this purpose, an ultra-voltage gain step-up DC-DC converter is proposed in this paper. The proposed converter has made an arrangement of the regenerative-boost fed switched inductor and capacitor configurations. Thereby, due to such an organization of structure, the proposed converter can develop an extremely high voltage-gain even at lower duty ratios. In addition, it has the advantage of lower switching stress across all power semi-conductive diodes. Furthermore, this paper describes the steady-state analysis and comparative features of the converter with existing recent literature. Finally, to validate theoretical analysis and test the feasibility and suitability of the proposed ultra-gain converter, the experimental results were observed by a 500 W fabricated prototype. [ABSTRACT FROM AUTHOR]

This paper presents an optimization framework for sequential reconfiguration using an assortment of switching devices and repair process in distribution system restoration. Compared to existing studies, this paper considers types, capabilities and operational limits of different switching devices, making it applicable in practice. We develop a novel multi-phase method to find the optimal sequential operation of various switching devices and repair faulted areas. We consider circuit breakers, reclosers, sectionalizers, load breaker switches, and fuses. The switching operation problem is decomposed into two mixed-integer linear programming (MILP) subproblems. The first subproblem determines the optimal network topology and estimates the number of steps to reach that topology, while the second subproblem generates a sequence of switching operations to coordinate the switches. For repairing the faults, we design an MILP model that dispatches repair crews to clear faults and replace melted fuses. After clearing a fault, we update the topology of the network by generating a new sequence of switching operations, and the process continues until all faults are cleared. To improve the computational efficiency, a network reduction algorithm is developed to group line sections, such that only switchable sections are present in the reduced network. The proposed method is validated on the IEEE 123-bus and 8500-bus systems. [ABSTRACT FROM AUTHOR]

The dc-dc converters with high step-up DC-voltage gain play a vital role in integrating low voltage DC sources. Though several converter topologies are reported in the recent past, attempts have been made to reduce the components, especially the switching devices, passive elements, converter losses, etc., of the converter. A novel DC-DC converter topology, viz., single switched impedance network (SSIN)-based converter with n-stage is proposed in this paper. The operation of the SSIN based converter in continuous and discontinuous conduction modes are discussed. The effect of parasitic elements on DC-voltage gain and efficiency of the SSIN is carried out. The small-signal model of the SSIN converter is derived. The performance of the SSIN converter is compared with the similar converter topologies. The 500 W prototypes of the SSIN with n = 1 and n = 2 are fabricated, and the experimental results are presented in this paper. To improve the converter performance, SiC-based semiconductor devices are used. The SSIN converter with two-stage has low switch loss at 500 W load, improved efficiency during high power and high output voltage operation, the switch stress of Vo/2, etc. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC), owing to the presence of a large number of submodules (SMs) and energy storing elements, requires a large footprint and initial investment. To address these issues, this paper proposes the switched modular multilevel converter (SMMC). It consists of two major elements; the chain-links (CLs), consisting of cascade connection of SMs as in MMC, and the single-pole-triple-throw (SPTT) switches, which can be realized using either the T-type or NPC-type switch strings. The SMMC works on the principle of connecting all the phase-legs in series and their respective positions are mutually interchanged. It offers a compact structure as the SMs count is reduced to 33% of MMC, which results in a much lower energy storage requirement. Furthermore, it does not have inter-phase circulating current problem and hence the CL inductors can also be avoided. The SMMC structure, operating principles, control, and modulation schemes are explained in detail. A detailed comparison of SMMC with the other major existing converters is carried out to highlight the important features of SMMC. The efficacy of SMMC is validated using PSCAD simulation studies with a 19-level grid-connected SMMC model. A 3-phase 19-level SMMC laboratory prototype is developed to further validate its feasibility. [ABSTRACT FROM AUTHOR]

The safety of converters is key to the stable operation of AC/DC hybrid power grids after AC faults. Thyristor valve current is a direct manifestation of the converter observability, but there are no measuring elements inside the converter, so the thyristor valve current can be reflected only indirectly through external electrical quantities. This paper proposes a virtual measurement scheme based on the temporal features of the converter terminal current. First, under the action of the trigger pulse, the polarity characteristics of the AC current and temporal features between the valves are utilized to predictive estimate the valve state. Then, when commutation failures occur and the bypass paths form, the conduction state of valve is constructed based on the relationship between AC and DC current. Last, when the valve is to be shut-off in the bypass path, the blocking state of the valve is corrected based on the unidirectional conductance characteristics of the valve. According to the above analysis, combined with the topological current equation of the converter, the valve current can be calculated in the whole process. Through the simulation of the different valve states and bypass paths and analysis of the field record data, the results show that the valve current can still be accurately calculated based on the virtual measurement scheme. [ABSTRACT FROM AUTHOR]

In this paper, we address the finite-time and fixed-time synchronization of a general class of switched neural networks (SNNs) with time delays subject to stochastic disturbances. Considering two types of switching in this class of SNNs: 1) intra-SNN state-dependent switching and 2) inter-SNN Markovian switching, we develop three control laws and derive three sets of sufficient conditions for both finite-time and fixed-time synchronization of SNNs subject to stochastic disturbances. We make two remarks on the effects of control-law parameters on synchronization settling time. Moreover, we derive several upper bounds of synchronization settling time and evaluate their pros and cons. Finally, we elaborate on two numerical examples to illustrate the viability of the theoretical results. [ABSTRACT FROM AUTHOR]

This paper focuses on the issue of network connectedness (NC) in security-constrained optimal transmission switching problems, which is complicated by branch contingencies and corrective line switching. Two criteria are firstly proposed with the principle of preserving NC as much as possible within reasonable limits. By extending the electrical flow based NC constraints, a proposition is derived to associate different cases of NC with the optimum of a linear program, yielding the mathematical formulation of the NC criteria. By Karush-Kuhn-Tucker conditions, this formulation is further transformed into a tractable version which can be incorporated with existing SCOTS models without affecting the applicability of original solution approaches. Finally, case studies on various networks and SCOTS models demonstrate the efficacy of the proposed approach. [ABSTRACT FROM AUTHOR]

Differential power processing (DPP) converters have been developed for photovoltaic (PV) panels to preclude energy yield reduction due to partial shading. In large-scale PV systems comprising numerous series-connected panels, DPP converters with good modularity are preferable because the number of series-connected panels varies depending on applications. This paper proposes a switched capacitor converter (SCC)-based modular DPP architecture for large-scale PV systems. Four panels are grouped as a module, each having a panel-level DPP converter, and modules are connected in series to form a string. The design of the panel-level DPP converter is fixed while the system can be arbitrarily extended by stacking modules, achieving good modularity. Adjacent panel-level DPP converters are dc-coupled, by which modules can be connected using long cables, mitigating installation limitations. The experimental results of the laboratory and field testing demonstrated the energy yield enhancement by 10%–20%, depending on shading conditions. [ABSTRACT FROM AUTHOR]

The paper develops two computationally efficient models, namely a detailed equivalent model and an average-value model, with provisions for representation of the critical state of converter blocking, for modular multilevel converters with embedded storage. These models are indispensable in the simulation of dc faults. The developed detailed equivalent model provides accuracy that matches electromagnetic transient (EMT) simulations, with much reduced computational burden; the developed average-value model represents the averaged behavior of the converter by neglecting switching transients. Both models are extensively evaluated in the context of an HVDC system against benchmark results form a detailed switching model developed in PSCAD/EMTDC. The results confirm the validity and accuracy of the models for steady state, transient, and faulted operating conditions including when the converter is blocked in response to a dc fault. [ABSTRACT FROM AUTHOR]

This paper proposes a novel dual input nine-level inverter (DINLI) topology which requires only seven controllable devices. The dual inputs are un-identical DC voltage sources in the ratio 1:3. A simple control scheme is derived by appropriately modifying the phase disposition pulse width modulation technique to generate high-quality 9-level output from the DINLI topology. At any given instant, a maximum of four switches conduct out of which only a maximum of two switches operate at high frequency, bringing down the switching and conduction losses significantly and improving the overall system efficiency. The bidirectional DINLI (BDINLI) topology with reactive power capability can be realized by replacing the unidirectional devices with the controlled switches (i.e., total nine switches). In addition, the proposed DINLI topology does not require extra voltage balancing circuits which further improves the efficiency. The DINLI operation is verified through MATLAB simulations for grid-connected applications and its extension to an n-level, 3-phase application is also investigated. Experiments performed on a 1KVA laboratory prototype to validate the theoretical claims. [ABSTRACT FROM AUTHOR]

Most microgrid protection schemes found in published literature suffer from a lack of generality in that they work well for the assumed topology, including type and placement of sources. Other generic protection schemes tend to be too complicated, too expensive, or both. To overcome these drawbacks, a topology-agnostic, scalable, and cost-aware protection based on fundamental principles that work in the presence of high penetration of inverter-based resources (IBRs) is developed and tested in this paper. The protection system also implements stable automatic reconfiguration of the healthy sections of the system after clearance of fault, thus increasing resilience by self-healing. To achieve this ambitious goal, stable inverter models are developed that operate in unbalanced networks in grid-connected and islanded modes, even with 100% IBRs, share power without conflicting controls, and can ride through faults while limiting fault currents. The scheme is tested for primary and backup protection and reconfiguration on the IEEE 123-node feeder in grid-connected and islanded modes with 15 IBRs connected to the system. [ABSTRACT FROM AUTHOR]

Miniaturization and low cost contribute to the development and popularization of wireless power transfer (WPT). Reducing the number of power conversion stages can reduce the volume and cost of the WPT converter, and even make it possible to improve the efficiency. A single-stage WPT converter with constant current (CC) and constant voltage (CV) output and its asymmetric modulation method are proposed in this paper. A direct AC-AC converter is applied to the primary side of the WPT converter to directly convert line-frequency AC to high-frequency AC. The applied direct AC-AC converter that can replace the commonly used multi-stage primary converter reduces the number of circuit devices, thereby reducing the volume and cost of primary converter. The proposed WPT converter can realize zero voltage switching (ZVS) and power factor correction (PFC). In order to achieve CC and CV output, a switchable hybrid compensation topology is applied to the proposed WPT converter. A 720-W experimental prototype was manufactured to verify the rationality of the proposed WPT converter and the correctness of the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper investigates the robust containment control problem of multiagent systems with heterogeneous uncertainty and nonlinearity while the nonlinear parts have to satisfy the Lipschitz condition. In this paper, both input time-delay and data transmission time-delay between the agents are considered simultaneously and communication topology of the multiagent systems may switch in the steady-state condition. Under the mentioned conditions, the objective of this paper is to make all the followers’ states converge to the convex hull shaped by the leaders’ states with an expected exponential rate. To this end, an appropriate smooth protocol is proposed. Then, a Lyapunov–Krasovskii functional composed of five terms is proposed and the stability condition is denoted by two linear matrix inequalities (LMIs). In addition to the stability assurance, solving the LMIs would obtain the suitable gains for the protocol. Finally, some numerical simulations are given to verify the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a novel data driven framework for detecting topology transitions in a distribution network. The framework analyzes data from phasor measurement units (PMUs) and relies on the fact that changes in network topology results in changes in the structure and admittance of the network. Using voltage and current phasors recorded by PMUs, the proposed method approximates network parameters using an ensemble-based deep learning model and thus, it does not require any knowledge of network parameters and load models. Using the prediction error of the proposed model, a connectivity matrix which shows the status of switches is constructed. In contrast to other methods, this proposed framework does not require a library of voltage and current transients associated with possible network transitions. It can also detect simultaneous switching actions and is robust to noise and load variations. The model yields a lower error detection rate, and its performance is validated using a modified version of the IEEE 33 bus network and a real feeder located in Queensland, Australia, under full and partial observability conditions. The proposed model has also been compared with another data driven method in terms of inference time and error detection rates. [ABSTRACT FROM AUTHOR]

The missing capability of DC fault current limitation is an inherent disadvantage in the typical half-bridge modular multilevel converter (MMC), which restricts its application in long-distance high voltage direct current (HVDC) systems. The full-bridge submodule (FBSM) and clamped double submodule (CDSM) topologies allow for fault current self-clearing, but also suffer from additional hardware cost and power losses. In this paper, an improved submodule topology utilizing the new reverse-blocking insulated gate bipolar transistor (RB-IGBT) is proposed to improve system economy without compromising its performance. The operating principles and DC fault characteristics of the proposed topology are analyzed in details, including comparison with various topologies in terms of cost, losses, fault current clearing speed and thermal. Compared with the traditional CDSM topology, the proposed RBSM can clear DC faults faster with reduced cost of switching devices. A DC fault protection strategy for MMC-HVDC system is also presented. Simulation results under normal operating, permanent and transient fault conditions are carried out to verify the effectiveness of the proposed topology. [ABSTRACT FROM AUTHOR]

The reliable operation of a power distribution system relies on a good prior knowledge of its topology and its system state. Although crucial, due to the lack of direct monitoring devices on the switch statuses, the topology information is often unavailable or outdated for the distribution system operators for real-time applications. Apart from the limited observability of the power distribution system, other challenges are the nonlinearity of the model, the complicated, unbalanced structure of the distribution system, and the scale of the system. To overcome the above challenges, this paper proposes a Bayesian-inference framework that allows us to simultaneously estimate the topology and the state of a three-phase, unbalanced power distribution system. Specifically, by using the very limited number of measurements available that are associated with the forecast load data, we efficiently recover the full Bayesian posterior distributions of the system topology under both normal and outage operation conditions. This is performed through an adaptive importance sampling procedure that greatly alleviates the computational burden of the traditional Monte-Carlo (MC)-sampling-based approach while maintaining a good estimation accuracy. The simulations conducted on the IEEE 123-bus test system and an unbalanced 1282-bus system reveal the excellent performances of the proposed method. [ABSTRACT FROM AUTHOR]

A multi-level boost topology based on a flying capacitor is compared in this work with the hybrid, multi-level, partial power processing topology already presented in the literature for use as a highly efficient and compact dc/dc stage in 1500-V, two-stage, grid-connected PV systems. Different variations of the resonant stage of the hybrid topology are analyzed and compared in terms of losses, volume and complexity. Full multivariable optimization is conducted for the multi-level boost topology with different number of levels and for all the analyzed variations of the resonant stage of the hybrid topology. Appropriately rated new classes of 650-V and 900-V WBG devices are included in the optimization algorithm. It is concluded that due to the dominant conduction losses and gap in the voltage rating of the commercially available WBG devices between 650V and 200V, increase of the number of levels over 4 leads to the deteriorated loss and volume performances. All the analysis related to the resonant stage of the hybrid topology is confirmed by detailed and comprehensive measurements of two prototypes of 4kW of nominal and 7kW of maximal power. Additionally, all the loss models applied in the optimization algorithms presented in this paper are confirmed by detailed measurements, thermal calibration and finite element thermal simulations of the wide bandgap devices and inductor designs employed in this work. [ABSTRACT FROM AUTHOR]

This paper presents a robust event-triggered model predictive control (MPC) strategy for multiple high-speed trains (MHSTs) with random switching topologies. Due to the complicated operation environment of high-speed railways, the communication topology of MHSTs system is time-varying and changes among a set of directed graphs, which can be characterized as a Markov chain. By adopting the concept of MPC, this paper studies the distributed cooperative leader-following consensus control for MHSTs, in which a novel event-triggered strategy is introduced to determine when information exchange among neighboring trains and control update are executed. Firstly, the leader-following consensus problem of MHSTs system is transformed to the stabilization of a Markov jump system and a sufficient condition for leader-following consensus is derived with stability analysis of the Markov jump system based on the robust event-triggered MPC scheme. Then, the robust event-triggered MPC algorithm which minimizes the objective function is proposed. By optimizing the objective function, the deviation of states and amplitude of the control force are optimized. The effectiveness of the proposed robust event-triggered MPC method on cooperative cruise control of MHSTs is illustrated by numerical examples. [ABSTRACT FROM AUTHOR]

The randomly switching communication topologies are of particular interest for researchers in the field of consensus control since the communication connection among multiple agents can randomly change with time and space. Following this pattern, this paper models the communication topology with the Markovian randomly switching graphs, since the Markovian chain process is usually used to model the network with Rayleigh fading channel. In this stochastic framework, this paper focuses on the consensus control and performance improvement problems of grouped agents with linear or linearized nominal dynamics. To solve this problem, a class of state-feedback controllers is proposed under the assumption that all the state measurements are available. These controllers are intrinsically distributed since they solely require the relative information between neighboring agents. Moreover, the notion of $\mathcal {H}_{\infty }$ ($\mathcal {H}_2$) stochastic consensus region integrated with transient performance is defined to measure the robustness of the proposed controllers with respect to the communication topologies. This paper theoretically shows that these controllers yield unbounded consensus region, which implies that they are well-designed. Furthermore, these controllers can improve the $\mathcal {H}_{\infty }$ , $\mathcal {H}_2$ consensus, and transient performances of agents subject to external and initial-state disturbances. At the end of this paper, numerical simulations and experiments are performed to verify the theoretical results. [ABSTRACT FROM AUTHOR]

This paper proposes a novel polygonal voltage space vector structure (SVS) having 30 sides, for a star-connected induction motor drive. The SVS eliminates the presence of harmonics up to 25th order from motor phase voltage throughout the entire modulation range, providing a torque profile devoid of lower order pulsations. Linear modulation is extended till 99.63% of base speed without exceeding the motor phase voltage rating. Topology consists of a dc-link fed primary inverter and two equal low voltage modular capacitor fed secondary inverters. Here the harmonics generated by the primary inverter is canceled by the secondary inverter which acts as a switched capacitive filter. Detailed description of the SVS generation and timing calculations are provided in this paper. Effectiveness of the proposed scheme is validated using experimental results, inverter loss calculations, and harmonic analysis. [ABSTRACT FROM AUTHOR]

Four-level hybrid-clamped inverter is a newly proposed topology that can operate under a wide voltage range without switches connected in series. However, when it is applied in medium voltage high power conversions, the flying capacitors in each phase will occupy a huge volume and a high switching frequency is required to restrain the voltage ripples. In order to overcome this drawback, a four-level active neutral-point clamped inverter is discussed in this paper, which consists of only six switches and no diodes or flying capacitors are required. In order to balance the neutral-point voltages under the full power factor and modulation index range, a capacitor voltage balance method based on carrier-overlapped pulsewidth modulation is proposed in this paper. The upper and lower dc-link capacitor voltages are balanced by zero-sequence voltage injection and the central dc-link capacitor voltage is balanced by adjusting the duty cycles of switching signals slightly. Simulation and experimental results are presented to confirm the validity of this method. [ABSTRACT FROM AUTHOR]

The development of wide band-gap semiconductor devices is rapidly promoting the development of power electronics technology, especially in high frequency (HF) power converter region. A category of HF power converter is switch-mode power amplifier (PA). This paper focuses on the implementation of a multiphase dc–dc PA with high bandwidth and high power rate. When naturally sampled phase-shifted carrier modulation is implemented in the practical digital control system to control this HF power converter, the pulsewidth error problem caused by limited domain frequency of control chip becomes much severer. As a result, dc voltage component of each phase becomes different under several conditions, leading to current imbalance among phase inductors. This paper analyzes this problem and proposes a sensorless control method to solve it, based on the injection of random sequence in reference wave. A four-phase prototype employing GaN devices is fabricated, switching at 1 MHz. Current imbalance and effectiveness of the proposed control method are verified by experimental results. The prototype is capable of uniformly amplifying sine signal within 200 kHz and a 350 kHz bandwidth random signal, with peak output power up to 810 W. [ABSTRACT FROM AUTHOR]

Satellite dc–dc power converters are required to have electromagnetic interference (EMI) compatibility as well as high reliability. The requirement of high reliability limits the complexity of the structure as well as the number of low-reliability components. In this paper, a conventional active-clamp-forward (ACF) topology is examined for a satellite converter owing to its relatively simple structure, small number of components, and good clamping capability regarding its switch voltage stress. However, it has a pulsating input current shape, a high di/dt level, and high switch voltage stress, which are disadvantageous with regard to the EMI filter size and high-input-voltage converter applications. To overcome these drawbacks, a new ACF topology with a continuous input current waveform is proposed. In the proposed waveform, the voltage stresses on the main switches are relieved, which is crucial to ensure the reliability of satellite FET switches, by utilizing a two-series connected structure. These features allow the proposed converter to serve as a high-input-voltage, high power-density satellite converter. In this paper, 100 W prototype converters with 50 V inputs operating at 300 kHz are built with a high power density of 47.9 W/in3. Experiments on these prototype converters are carried out to verify the features. [ABSTRACT FROM AUTHOR]

This paper presents a 5-level inverter topology for open-end induction motor drives by using a single dc source. The open stator windings of the drive are supplied with a 3-level flying capacitor inverter from one end and capacitor-fed 2-level inverter from another end. The voltage ratio of the dc link to the capacitor in 2-level inverter is maintained at 4:1 ratio to generate five-level voltage output. The capacitor in 2-level inverter is balanced by the switching redundant vector combinations from both the inverters while the floating capacitors in the 3-level inverter are balanced by using redundant switching states. The proposed topology gives 5-level operation with less number of floating capacitors and power semiconductor switches compared to other existing topologies. Also, the balancing of the capacitors is independent of load power factor and modulation index. Further, the generalization of the proposed dual inverter scheme for any n-level inverter is also included in this paper. The experimental results and required analysis are also presented to validate the inverter scheme. [ABSTRACT FROM AUTHOR]

Active magnetic bearing is a core technology for high-speed rotational machines. Power electronics converter as the active magnetic bearing drive is the actuation unit and its topology highly impacts the performance of the bearing system. This paper introduces the progress of topology of active magnetic bearing drive. The initial topology of an H-bridge does not sufficiently utilize the power electronics devices. The topology with half-bridge and shared phase-leg has been proposed as the fundamental topology. In this paper, two approaches of novel magnetic bearing drive topology modification have been developed on the basis of the fundamental topology. In the first approach, central phase-leg for multiaxis magnetic bearing drive can be further shared and the power electronic devices can be globally optimized in the whole system. Further, a topology with current in the reverse direction can reduce the central phase-leg current rating and power losses. In the second approach, fault-tolerant magnetic bearing drive topology has been developed on the basis of the fundamental topology, too. It can ride-through the open-circuit fault of power electronics switch-in operation and keep levitation for the magnetic bearing. The series work of novel topologies can improve the performance of an active magnetic bearing system in application. [ABSTRACT FROM AUTHOR]

Compared with the conventional two-level dual-active-bridge (DAB) dc–dc converter, the three-level DAB converter could operate with lower voltage rated switching devices and provide more control degrees of freedom, which enhances the control flexibility. This paper proposes a modulation strategy with five control degrees of freedom. In the previous work with multiple control degrees, the optimization strategies for efficiency or inductor current minimization are investigated; however, these strategies all need detailed mode analysis and complex mathematical optimization tools to obtain the optimal duty cycles. In this paper, an optimization strategy for the root-mean-square value of the inductor current is proposed. This method extracts the fundamental and third-harmonic components from the high-frequency voltages on both sides and adjusts the amplitude of the bridge voltages by the vector diagram to obtain the optimal duty cycles. The inductor current can be reduced significantly at light loads with the proposed strategy, so the efficiency of the converter can be improved. Moreover, the optimization process does not need the detailed operation analysis of the converter, nor does it require the complex mathematical optimization tools. Finally, the performance of the three-level DAB and the optimization strategy are verified by the experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a unified second-stage LC filter applied in the three-state switching cell buck–boost converter, which provides current and voltage with low ripple and low noise. The unified second-stage filter promotes a reduction in the number of devices while maintaining the filtering performance of the converter, with second-stage LC filters at the input and at the output. Moreover, the unified filter, when associated with a three-state switching cell buck–boost converter, allows a size reduction of filter devices, especially for designs with duty cycle range around 1/2. Furthermore, the unified filter arrangement provides nondissipative clamping of switching devices and reduce the system order when compared to the converter with second-stage LC filters. In this paper, the static and dynamic characteristics of the proposed converter in continuous conduction mode (CCM) are reported. Experimental data were obtained from a laboratory prototype with an input range of 32 $\sim$ 72 V, constant output of 48 V, a load of 150 W, and switching frequency of 45 kHz. The measured efficiency for the rated load was 97% for maximum input voltage. A comparison of the size and performance of the proposed filter with the topology that uses second-stage LC filters at the input and at the output is also presented. [ABSTRACT FROM AUTHOR]

In this paper, a new bidirectional dc-dc converter that is based on the quadratic and switched-capacitor structures is proposed for Electric Vehicle applications. The proposed converter has high voltage conversion ratios, low voltage stress on the semiconductor devices, constant potential difference between the grounds of its low voltage and high voltage ports, and continuous current at its low voltage port. Synchronous rectification is utilized to enhance the efficiency of the converter. In addition, an extended version of the proposed converter is discussed in this paper. Finally, the experimental results obtained from a 2-kW/800-V scaled-down prototype validate the feasibility of the proposed topology and the correctness of its theoretical analysis. [ABSTRACT FROM AUTHOR]

In order to increase the efficiency of modern microprocessor power supplies used in data centers, 380-V dc power distribution systems have been attracting attention due to their high efficiency and high reliability. This paper presents an innovative single-stage approach for 380-V voltage regulator modules (VRMs) based on a quasi-resonant multilevel topology constant on-time operation. The proposed topology inherently integrates the multiphase approach, providing fast phase shedding and flat high-efficiency curves even at light-load conditions. This is a unique advantage, which is not possible to establish in the two-stage approach, which is very important in server architectures, and where high efficiency is required even at light-load conditions. This paper analyzes the circuit topology and proposes a control architecture for fast transient response, including current-sharing capabilities. The digital controller has been implemented in 0.16- $\mu$ m lithography together with a digital pulsewidth modulation with a 195-ps resolution and a 40-MS/s 7-bit analog-to-digital converter. Experimental results show an efficiency of 93% for a 120-A 380–1.8-V VRM power supply. [ABSTRACT FROM AUTHOR]

This paper proposes a fifth-order resonant immittance network based dual-active-bridge (DAB) converter and an optimal modulation method that will ensure high-efficiency operation of the converter under wide-range variations in voltage ratio and output power level. The proposed modulation method is based on the concept of total power loss minimization, where a loss model is developed and an optimization algorithm is formulated to compute the optimal set of internal and external phase shift parameters that will lead to the maximum efficiency for a given set of operating parameters including voltage ratio and output power level. It is found that to maintain high-efficiency operation under wide-range variations in voltage ratio and output power level, the DAB converter is required to switch between different operation modes and neither soft-switching operation nor unity-power-factor operation is able to achieve wide-range high efficiency performance when used alone. The importance of $reconfigurability$ of operation mode for achieving wide-range high efficiency performance is clearly illustrated in this paper. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

The emergence of applications which require high-voltage switches has created a tendency to use semiconductor device series stacks. These series stacks permit operation at blocking voltages above semiconductor elements’ nominal voltage. Insulated-gate bipolar transistors (IGBT) are currently utilized for controllability and switching speed, when these topologies are employed. The main challenge therewith is guaranteeing voltage balance between IGBTs, both when blocked and when switching transistors. Most of the methods which have been proposed to mitigate static and dynamic voltage unbalances increase transistor losses. The series stack loss-less high voltage switch (LHVS) which mitigates voltage unbalances, thus reducing switching losses, is presented in this paper. LHVS consists of a circuit, which ensures soft IGBT switching, an energy recovery circuit, and a gate delay compensation circuit. Additionally, the insulation voltage level is guaranteed to be equal between control circuit and high-voltage side of each IGBT. The operating principle of the LHVS is detailed in this paper, as is experimental validation which has been performed for three series stack modules. Static unbalances are reduced to 1%, while the differences between collector–emitter voltage curves in switching “on” do not surpass 8 ns, and switching losses are reduced by 41%, as compared to the hard-switching topology. [ABSTRACT FROM AUTHOR]

Multilevel inverters (MLIs) are playing a pivotal role in the power sector with potential applications, such as interfacing renewable energy sources with the grid and several industrial drive applications. MLIs with a smaller number of switching devices are more promising due to their compact size, reduced cost, and higher efficiency compared with their traditional counterparts. This paper, therefore, presents a new three-phase seven-level inverter. This topology is a combination of two cascade-connected two-level voltage-source inverters (VSIs) and H-bridge cells with flying capacitors (FCs). This paper presents the operating principle and the balancing technique for the dc-link capacitors and FCs. The generation of various output voltage levels and the limitation of the sinusoidal pulsewidth modulation control for FC voltage balancing is also presented. The number of components in the proposed circuit configuration and their voltage ratings are considerably lower compared with the recently proposed topologies. The behavior of the proposed circuit configuration is first assessed with simulation studies and is then tested with a laboratory prototype. The simulation and experimental results validate the effectiveness of the proposed topology and the voltage balancing technique. [ABSTRACT FROM AUTHOR]

This paper deals with a multilevel ac–ac double conversion system that uses the intercell transformer (ICT) for applications which include generating systems and the interfacing of renewable energy sources with the utility grids. Each phase of the proposed configuration is formed through the ICT interleaving operation of two multilevel 5-level E-type legs to achieve the 3-phase 5-level back-to-back E-type converter (3Φ5L BTB E-type converter). The analytical procedure to select the inductance and capacitance values of both the input and output filters is described in the paper. Furthermore, the design and implementation of the input/output ICTs and inductors is discussed. The simulation and the experimental results on the 20-kVA interleaved 3Φ5L BTB E-type converter prototype are presented to validate the proposed analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a soft-switched modulation technique with synchronous rectification for an isolated single-stage single-phase matrix-type dc–ac converter. The dc side consists of a full bridge inverter, and the ac side is a 2×2 matrix converter-based cycloconverter. The proposed unipolar modulation strategy provides zero current switching/zero voltage switching (ZVS) for the ac side devices and ZVS-on for the dc side devices. It also allows natural commutation of the current flowing through the secondary side leakage inductor of the isolation transformer and the grid inductor during unity power factor (UPF) condition, thus eliminates the requirement of snubber circuit. An improved soft-switched flyback-based regenerative snubber circuit is also presented for non-UPF operation. Proposed snubber circuit recycles the energy stored in the snubber capacitors in every switching cycle. A guideline to design snubber circuit along with a comparative study is discussed in this paper. Performance of the proposed hybrid modulation technique is evaluated in an SiC mosfet based 1.2-kW dc–ac converter prototype. A detailed analysis of the converter performance has been presented in this paper considering the circuit non-idealities. [ABSTRACT FROM AUTHOR]

Fault tolerance in wind turbines is considered crucial to increase their reliability and availability levels. This paper presents a fault-tolerant direct-drive permanent magnet synchronous generator (PMSG) using new direct control techniques, with the ability to handle power semiconductor open-circuit faults in the full-scale back-to-back converter. The fault-tolerant topology consists of a five-leg converter, with a shared leg connected to a generator phase and to its corresponding grid phase, through a triode for alternating current (TRIAC). The main contribution of this paper consists of the development of an alternative direct torque control and direct power control schemes for both machine-side converter and grid-side converter, respectively. Moreover, a reliable fault diagnostics algorithm without requiring additional sensors is also integrated, providing the information required to instantaneously trigger fault-tolerant remedial strategies. Simulation and experimental results are presented to validate the effectiveness of the proposed fault-tolerant PMSG drive. [ABSTRACT FROM AUTHOR]

This paper presents a novel seven-level inverter topology for medium-voltage high-power applications. It consists of eight active switches and two inner flying capacitor (FC) units forming a similar structure as in a conventional active neutral-point-clamped (ANPC) inverter. This unique arrangement reduces the number of active and passive components. A simple modulation technique reduces cost and complexity in the control system design without compromising reactive power capability. In addition, compared to major conventional seven-level inverter topologies, such as the neutral point clamped, FC, cascaded H-bridge, and ANPC topologies, the new topology reduces the dc-link voltage requirement by 50%. This recued dc-link voltage makes the new topology appealing for various industrial applications. Experimental results from a 2.2-kVA prototype are presented to support the theoretical analysis presented in this paper. The prototype demonstrates a conversion efficiency of around 97.2% ± 1% for a wide load range. [ABSTRACT FROM AUTHOR]

This paper presents bidirectional grid-connected modular multilevel converters (MMC) with direct digital control and division-summation processes to achieve power-injection and rectification functions. A direct digital control is developed to track current references, regulate dc-bus voltage and cell voltage, and balance the upper and lower dc-bus voltages. It can accommodate wide filter-inductance variation and take care of source voltage harmonics to achieve tight current tracking and low distortion output current. Based on the power-balance principle, the commands of arm currents can be determined directly. In this paper, the MMC configuration is introduced first, and then the control laws for current tracking and voltage regulation are derived in detail. Experimental and simulated results obtained from two 50 kW MMCs operated in power-injection and rectification modes have verified the analysis and discussion. [ABSTRACT FROM AUTHOR]

This paper presents an interleaved boost converter with a bifold Dickson voltage multiplier suitable for interfacing low-voltage renewable energy sources to high-voltage distribution buses and other applications that require a high-voltage-gain conversion ratio. The proposed converter was constructed from two stages: an interleaved boost stage, which contains two inductors operated by two low-side active switches, and a voltage multiplier cell (VMC) stage, which mainly consists of diodes and capacitors to increase the overall voltage gain. The proposed converter offers a high-voltage-gain ratio with low voltage stress on the semiconductor switches as well as the passive components. This allows the selection of efficient and compact components. Moreover, the required inductance that ensures operation in the continuous conduction mode (CCM) is lower than the one in the conventional interleaved boost converter. The distinction of the proposed converter is that the inductors’ currents are equal, regardless of the number of VMCs. Equal sharing of interleaved boost-stage currents reduces the conduction loss in the active switches as well as the inductors and thus improves the overall efficiency, as the conduction power loss is a quadratic function. In this paper, the theory of operation and steady-state analysis of the proposed converter are illustrated and verified by simulation results. A $\text{200-W}$ hardware prototype was implemented to convert a $\text{20-V}$ input source to a $\text{400-V}$ dc load and validate both the theory and the simulation. [ABSTRACT FROM AUTHOR]

Multilevel inverters (MLIs) are being used in wide range of power electronic applications. These converters have attracted a lot of attention during recent years and exist in different topologies with similar basic concepts. This paper presents five main submodules (SMs) to be used as the basic structures of MLIs. The paper reviews the common MLI topologies from the structural point of view. The topologies are divided into the different SMs to show conventional MLI configurations and future topologies that can be created from the main SMs. A comparative study between different topologies is performed in detail. The MLIs are categorized and investigated with from different perspectives such as the number of components, the ability to create inherent negative voltage, working in regeneration mode and using single dc source. [ABSTRACT FROM AUTHOR]