Search

This paper proposes a new high-efficiency photovoltaic (PV) converter for grid connection through a high-leg delta transformer. The converter is composed of a symmetrically connected boost converter and three half-bridge inverters. One of the three half-bridge inverters is connected to the boost converter, and the others are directly connected to the PV terminals. As a result, this circuit configuration enables to reduce the power losses in both boost converter and inverters. This paper also proposes a new cooperative control method between the symmetrically connected boost converter and inverter. The control method can reduce the average switching frequency to 75% of that in a conventional one, resulting in a great reduction in the switching power loss. Experimental results confirm that the proposed circuit configuration makes it possible to improve its European efficiency from 91.6% to 94.5%. Moreover, system performance is evaluated on the assumption of maximum power point tracking operation. [ABSTRACT FROM AUTHOR]

This paper presents a unified framework for the modeling, analysis, and design of load-independent Class E and Class EF inverters and rectifiers. These circuits are able to maintain zero-voltage switching and, hence, high efficiency for a wide load range without requiring tuning or use of a feedback loop, and to simultaneously achieve a constant amplitude ac voltage or current in inversion and a constant dc output voltage or current in rectification. As switching frequencies are gradually stepping into the megahertz (MHz) region with the use of wide-bandgap (WBG) devices such as GaN and SiC, switching loss, implementing fast control loops, and current sensing become a challenge, which load-independent operation is able to address, thus allowing exploitation of the high-frequency capability of WBG devices. The traditional Class E and EF topologies are first presented, and the conditions for load-independent operation are derived mathematically; then, a thorough analytical characterization of the circuit performance is carried out in terms of voltage and current stresses and the power-output capability. From this, design contours and tables are presented to enable the rapid implementation of these converters given particular power and load requirements. Three different design examples are used to showcase the capability of these converters in typical MHz power conversion applications using the design equations and methods presented in this paper. The design examples are chosen toward enabling efficient and high-power-density MHz converters for wireless power transfer (WPT) applications and dc/dc conversion. Specifically, a 150-W 13.56-MHz Class EF inverter for WPT, a 150-W 10-MHz miniature Class E boost converter, and a lightweight wirelessly powered drone using a 20-W 13.56-MHz Class E synchronous rectifier have been designed and are presented here. [ABSTRACT FROM AUTHOR]

To support the development of high-frequency ac microgrids in terms of compact design, high-voltage gain and low total harmonic distortion (THD), a buck–boost dual-leg-integrated step-up inverter is proposed in this paper. The inverter is formed by integrating a buck–boost converter into a conventional single-phase full-bridge inverter by sharing the upper switch and the body diode of the lower switch in both bridge-legs. Consequently, the component count is significantly reduced over the step-up inverter counterparts. In addition, to address the drawbacks of hybrid modulation methods adopted by existing dual-leg-integrated inverters, such as double-variable control, and high THD of output voltage/current at high input voltage and heavy load conditions, unipolar frequency doubling sinusoidal pulse width modulation scheme is adopted in this inverter. As a result, the modulation ratio M becomes the only control variable to regulate the output voltage/current and the control is simplified. The THD of the proposed inverter output can remain low throughout the entire input voltage range and load power range. This paper presents the topology derivation procedure, operation principle, and steady-state characteristics of the proposed inverter. To validate the effectiveness of theory, experimental results of a 400 W hardware prototype, where the output voltage frequency is at 500 Hz, are reported. [ABSTRACT FROM PUBLISHER]

This paper introduces a new configuration of bidirectional multilevel converter in electric vehicle (EV) applications. It has multilevel dc–dc converter with a dc link capacitor voltage balance feature. The multilevel dc–dc converter operates in a bidirectional manner, which is a fundamental requirement in EVs. Compared to the conventional configurations, the proposed one only implements two extra power switches and a capacitor to balance the voltage of the T-type multilevel inverter (MLI) capacitor over a complete drive cycle or at fault conditions. Therefore, no extra isolated sensor, control loops, and/or special switching pattern are required. Moreover, the proposed configuration due to the high-frequency cycle-by-cycle voltage balance between ${C_N}$ and ${C_P}$ , the bulky electrolytic capacitors used in T-type MLI, are replaced with more reliable longer life film capacitors. This will result in a size and weight reduction of the converter by 20%. This allows more real estate for the EV battery in the chassis’ space envelope to increase its capacity. The proposed configuration is tested and validated using a matlab/Simulink simulation model. A laboratory prototype of 1 kW is built to provide the proof of concept results as well. [ABSTRACT FROM AUTHOR]

This paper proposes a switching strategy for the Z-source inverter (ZSI), which has unequal short-through intervals to reduce the current ripple in the inductor of its impedance source. A size reduction of the inductor of the ZSI is one of the important issues in improving the power density of the ZSI, and the inductor current ripple reduction is required to achieve it. The proposed method can reduce the inductor current ripple by 27.8% compared with the conventional method that has equal short-through intervals without increasing the number of inverter switching. The proposed operation and ripple reduction were confirmed in experiments with a 3-kW-class laboratory prototype. Its result agreed to the calculated results, and it was confirmed that there is no increase in circuit losses caused by the application of the proposed method. [ABSTRACT FROM AUTHOR]

An enhanced DC–DC converter is proposed in this paper, based on the combination of the Cuk and SEPIC converters, which is well-suited for solar photovoltaic (PV) applications. The converter uses only one switch (which is ground-referenced, so simple gate drive circuitry may be used), yet provides dual outputs in the form of a bipolar DC bus. The bipolar output from the DC–DC converter is able to send power to the grid via any inverter with a unipolar or bipolar DC input, and leakage currents can be eliminated if the latter type is used without using lossy DC capacitors in the load current loop. The proposed converter uses integrated magnetics cores to couple the input and output inductors, which significantly reduces the input current ripple and hence greatly improves the power extracted from the solar PV system. The design methodology along with simulation, experimental waveforms, and efficiency measurements of a 4-kW DC–DC converter are presented to prove the concept of the proposed converter. Furthermore, a 1-kW inverter is also developed to demonstrate the converter's grid-connection potential. [ABSTRACT FROM AUTHOR]

A 1-φ hybrid nine-level inverter (H9LI) topology has been proposed in this paper. The proposed H9LI topology uses a simple phase disposition pulsewidth modulation strategy to generate nine-voltage levels in the output. The main advantage of this topology is that it has a low switch count (ten switches) compared to the existing nine-level inverter topologies. To regulate the voltage across auxiliary capacitor, two innovative control techniques are proposed, which are integrated with the inverter modulation technique itself. Hence, it does not require any extra voltage balancing circuits to maintain the voltage across the auxiliary capacitor and input dc capacitors. A major advantage of these control techniques is that they eliminate the sensing of the coupled inductor current. Another significant advantage of H9LI is that loss distribution among all the power switches is more uniform compared to existing nine-level inverters. Due to low part count and absence of extra voltage balancing circuits, the H9LI achieves higher efficiency (η ≍ 94.5%) and lower cost. Furthermore, the requirement of filter size reduces due to the presence of coupled inductor in H9LI. The proposed 1-φ grid connected H9LI is verified through MATLAB/Simulink simulations and validated through experiments on a laboratory prototype of 400-VA rating. [ABSTRACT FROM AUTHOR]

In this paper, capacitor current sensorless control by using an observer is applied in a seamless transfer single-phase inverter. The proposed control system is a multiloop control system. The control loop is composed of a capacitor voltage outer control loop and capacitor current inner control loop for stand-alone mode. For on-grid mode, the grid current outer loop controller is combined with the stand-alone control structure to form a simple controller structure for mode switching. The capacitor current feedback signal is calculated using the observer in the discrete-time domain and thus sensors are not required. Use of the proposed observer for the inverter with capacitor current control has many advantages, such as sensorless capacitor current calculation, one-sample-ahead data prediction for sampling delay compensation, and an average capacitor current without ripple components. Verification of the theoretical analysis is presented through simulation and experiment. A 5-kW single-phase inverter prototype combined with a Li-ion battery is set up with a digital controller using a TI TMS320F28377D microcontroller unit to confirm the feasibility of the system. [ABSTRACT FROM AUTHOR]

In this paper, a three-level quasi-switched boost T-type inverter (3L qSBT2I) is proposed. A new pulse-width modulated (PWM) control method is presented to reduce the inductor current ripple of the qSBT2 I. In the introduced PWM technique, the shoot-through duty cycle is maintained constant to keep the modulation index as high as possible. Then, the only control parameters of the qSBT2I are the duty cycles of the two additional switches. By controlling the duty cycles of the two additional switches, the voltage gain of the proposed qSBT2 I can be improved to a value larger than that of the conventional 3L impedance source inverters. The steady-state analysis, operating principles, and comparisons with the impedance source-based 3L inverters are presented. A 1-kW prototype is constructed to verify the operating principle of the 3L qSBT2I. An indirect dc-link voltage regulator and a capacitor voltage-balance controller are applied to the proposed qSBT2I. Simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper presents a step in microlevel photovoltaic (PV) summation technology for combining unsymmetrical PV modules with differences in specification and age, relocation on nonfertile land, or multilocation mounting by designing an add-on modular hardware interface to a multi-input single-output (MISO) dc bus, using an MISO controller employing a suitable maximum power point (MPP) tracker under partial shading/long distance/mismatching PV module conditions along with a sensor-less PV vector control inverter (PV–VCI) driving a three-phase asynchronous squirrel cage induction motor dedicated to irrigation, with the facility of autoconfiguration/autotuning at the beginning. A PV source gets automatically added/removed in a ramp profile in proportion to the load in steps, thus keeping on only when required, enabling high efficiency, minimum heating, and prolonged life as that of a PV module. The contribution includes a reduced PV energy cost per watt by 24.10%, improved return on investment by 27.48%, improved water discharge yield by 11.06%, and improved MPP tracker impact by 14.59% with 90.88% MISO system efficiency compared to a normal scheme. [ABSTRACT FROM AUTHOR]

This paper investigates a multilevel inverter composed of series/parallel-connected H-bridges. The presented structure can be used for applications in which the use of semiconductor switches with low-voltage and low-current ratings is intended. A comprehensive system model, an overall control strategy to adjust the output voltage with constant magnitude and frequency, and a level-shifted PWM (LS-PWM) strategy based on a voltage vectors unidimensional analysis and a plane analysis are presented. The LS-PWM is capable of mitigating the low-frequency circulating current, thus generating multilevel voltage signals with low harmonic distortion, maximum number of levels, and low dv/dt. In addition, considering a wide range of values of voltages and currents and various power levels, the total converter losses are reduced compared with the conventional multilevel converters. Two multilevel conventional inverters with the same number of semiconductor switches are used for comparison. Simulation and experimental results demonstrate the feasibility of the studied converter. [ABSTRACT FROM AUTHOR]

Impedance-source converters, an emerging technology in electric energy conversion, overcome limitations of conventional solutions by the use of specific impedance-source networks. Focus of this paper is on the topologies of galvanically isolated impedance-source dc–dc converters. These converters are particularly appropriate for distributed generation systems with renewable or alternative energy sources, which require input voltage and load regulation in a wide range. We review here the basic topologies for researchers and engineers, and classify all the topologies of the impedance-source galvanically isolated dc–dc converters according to the element that transfers energy from the input to the output: a transformer, a coupled inductor, or their combination. This classification reveals advantages and disadvantages, as well as a wide space for further research. This paper also outlines the most promising research directions in this field. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel bidirectional inverter, named series ac-link inverter. This three-phase inverter belongs to a new class of partial resonant ac-link converters in which the link is formed by a series ac inductor/capacitor (LC) pair having low reactive ratings. The input and output of this converter can be either dc, ac, single-phase, or multiphase. Therefore, they can appear as dc–dc, dc–ac, ac–dc, and ac–ac configurations. In all of these configurations, the ac capacitor is the main energy-storage element, and the inductor is merely added to facilitate the zero-current turnoff of the switches and their soft turn-on. Due to the zero-current turnoff of the switches in the proposed converter, the use of SCRs with natural commutation is possible as well. Since the current and voltage of the link are both alternating, no bulky dc-electrolytic capacitors are required in this converter. This paper mainly focuses on bidirectional dc to three-phase ac conversion. This single-stage inverter can step up or step down the voltage in a wide range. If galvanic isolation is required a single-phase high-frequency transformer can be added to the link. In the proposed inverter, the power can flow in both directions, and therefore, it is an excellent candidate for battery-utility interface and electric vehicle applications. In this paper, the principles of the operation of the proposed inverter, along with its design and analysis, are studied. Moreover, the performance of the proposed configuration is evaluated in this paper. Both simulation and experimental results are included. [ABSTRACT FROM AUTHOR]

Connecting legs in parallel in a voltage source inverter is a way to increase the output current and, thus, its rated power. The connection can be made using either coupled or uncoupled inductors, and achieving an even contribution to the output current from all the legs is a crucial issue. Circulating currents produce additional losses and stress to the power devices of the converter. Therefore, they should be controlled and minimized. An efficient technique to attain such balance when coupled inductors are used is presented in this paper. The proposed technique can also be used when the inductors are uncoupled, since it is a particular case where the coupling coefficients are zero. This technique does not include proportional–integral controllers and does not require any parameter tuning either. The exact control action needed to reach current balance is straightforwardly calculated and applied. Experimental results are shown in this paper to verify the efficiency of the proposed balancing method. [ABSTRACT FROM PUBLISHER]

This paper proposes a new circuit configuration and a control scheme for a single-phase current-source inverter with a power decoupling circuit which is called as the active buffer. The proposed inverter achieves a low-dc-input voltage ripple and also provides a sinusoidal current that can achieve unity power factor, without large passive components in the dc bus such as smoothing inductors and electrolytic capacitors. These components are conventionally required in order to decouple the power pulsation caused by the single-phase power source. In this paper, the fundamental operations of the proposed inverter are demonstrated experimentally. From the experimental results, the input voltage ripple is 8.87%, and the output current total harmonic distortion is 4.24%. In addition, an output power factor of 99% and a maximum efficiency of 94.9% are obtained. Finally, it is confirmed that the maximum power densities of the conventional circuit and the proposed circuit are 2.75 kW/L at the switching frequency of 70 kHz and 4.86 kW/L at the switching frequency of 80 kHz, respectively. [ABSTRACT FROM AUTHOR]

This paper proposes the combination of a novel modified quasi-Z-source (MqZS) inverter with a single-phase symmetrical hybrid three-level inverter in order to boost the inverter three-level output voltage. The proposed single-phase MqZS hybrid three-level inverter provides a higher boost ability and reduces the number of inductors in the source impedance, compared with both the single-phase three-level neural-point clamped quasi-Z-source inverter and the single-phase quasi-Z-source cascaded multilevel inverter. Additionally, it can be extended to obtain the nine-level output voltage by cascading two three-level pulse width modulation switching cells with a separate MqZS and a dc source, which herein is called a single-phase MqZS cascaded hybrid five-level inverter (MqZS-CHI). A modified modulation technique based on an alternative phase opposition disposition scheme is suggested to effectively control the shoot-through state for boosting the dc-link voltage and balancing the two series capacitor voltages of the MqZS. The performances of both the proposed MqZS-CHI and the modulation techniques are verified through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

This paper introduces series work of common-mode (CM) voltage reduction for the paralleled inverters. The paralleled inverters’ phase-legs are connected through coupling inductors and the combined three-phase currents are provided to the load. Interleaving is an approach to reduce the CM voltage for the paralleled inverters but it cannot eliminate CM voltage. A novel pulse-width-modulation (PWM) method for paralleled inverters which can theoretically achieve zero CM voltage is developed. Considering the basic voltage vectors in each inverter, novel paralleled voltage vectors which have zero CM voltage are proposed to combine the reference voltage vector. The action time's distribution and voltage vectors’ sending sequence for each inverter are also introduced. The proposed PWM method can make sure the voltage of the two inverters are balanced in each switching cycle and limits the circulating current through small coupling inductors. Similar to interleaving space vector PWM, the proposed zero CM PWM also has the ability to reduce the output current ripple and electromagnetic interference (EMI). Simulation and experimental results are provided to show the advantage of paralleled inverters in CM voltage reduction and validate the proposed method has good performance to reduce CM current and CM EMI noise. [ABSTRACT FROM PUBLISHER]

This paper presents a variable switching point predictive current control (VSP $^2$CC) for the quasi-Z-source inverter (qZSI). The proposed VSP $^2$CC aims to remove the output current error on the ac side, as well as the inductor current and capacitor voltage errors of the quasi-Z-source network on the dc side of the converter. Unlike the previously presented direct model predictive control (MPC) strategies for the qZSI, the proposed control scheme can directly apply the switching signals not only at the discrete time instants, but at any time instant within the sampling interval. Consequently, the shoot-through state can be applied for a shorter time than the sampling interval, resulting in lower output and inductor currents ripples. Experimental results based on field programmable gate array are provided to verify the effectiveness of the introduced control method. As it is shown, the proposed method leads to lower inductor current ripples and less output current total harmonic distortion when compared with the conventional direct MPC. [ABSTRACT FROM AUTHOR]

In this paper, a new nonisolated high-voltage-gain boost converter is proposed. The proposed converter is constructed by adding an additional inductor to a conventional three-level-boost (TLB) converter. When compared with the conventional boost and TLB converters, the proposed converter can achieve higher voltage conversion ratio with reduced voltage and current stresses in the switches. In particular, the proposed converter can reduce the losses of active devices by reducing the current of the switch compared to conventional converters, thus, can achieve high efficiency. In addition, the proposed converter automatically balances the output voltages for an unbalanced load without the need for any additional control strategy or auxiliary circuit. A 2-kW prototype converter was built and tested to verify performances of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, a dc to ac converter with the ability of voltage increasing is presented. This inverter is designed in a way that just one dc source is used. Also, by using power storage technique and with combining charged capacitors and dc source in series form, output voltage levels can be increased. This inverter is in a modular structure and has the ability of capacitor's voltage self-balancing. H-bridge inverter was not used at the end of the proposed converter and all elements tolerate a voltage stress equal to the amount of input dc source. This leads to remarkable decrease of total standing voltage and peak inverse voltage. Other advantage of the proposed inverter is its potentiality of performance in high-frequency applications. The modular form of the proposed inverter provides the potentiality of extension to higher voltage levels and eases the maintenance. Moreover, considering to the fact that the stress of all components of the suggested inverter is equal to the input source, the performance in high voltage is added to the characteristics of the proposed inverter. The nine-level structure of the proposed inverter is simulated and laboratory test is carried out for the verification of its performance. [ABSTRACT FROM PUBLISHER]

The quasi-Z-source inverter (qZSI) has attracted much attention for motor drives and renewable energy applications due to its capability to boost or buck in a single converter stage. However, this capability is associated with different challenges related to the closed-loop control of currents, control the dc capacitor voltage, produce three-phase ac output current with high dynamic performance, and obtain continuous and low ripple input current. This paper presents a predictive control strategy for a three-phase qZSI that fulfills these requirements without adding any additional layers of control loops. The proposed controller implements a discrete-time model of the qZSI to predict the future behavior of the circuit variables for each switching state, along with a set of multiobjective control variables all in one cost function. The quasi-impedance network and the ac load are considered together when designing the controller in order to obtain stability of the impedance network with a step change in the output reference. A detailed comparative investigation between the proposed controller and the conventional proportional-integral (PI) controller is presented to prove the superiority of the proposed method over the conventional control method. Simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper identifies the characteristics of a current source inverter operating in discontinuous conduction mode, and proposes a new multiobjective pulse-width modulation (PWM) method to mitigate voltage boosting and harmonic distortion effects. The method takes into account load impedance effects. Controls are also developed to enable transition between the multiobjective PWM method and conventional PWM as the current source inverter operates in discontinuous and continuous modes of operation. The concept is verified experimentally on a 3 kW test bed. [ABSTRACT FROM AUTHOR]

A family of isolated buck–boost dc/dc converter for wide input-voltage range is proposed in this paper, and the full-bridge (FB) boost converter, being one of the typical topologies, is analyzed. Due to the existence of the resonant inductor (including the leakage inductor), the FB-boost converter can only adopt the two-edge-modulation (TEM) scheme with the FB cell being leading-edge modulated and the boost cell being trailing-edge modulated to minimize the inductor current ripple over the input-voltage range, and a phase-shift-control-scheme-based TEM with the use of the market available controller IC such as UC3895 is proposed, which realizes phase-shifted control for the FB cell to achieve zero-voltage switching. In order to improve the reliability and efficiency of the FB-boost converter, a three-mode dual-frequency control scheme is proposed, in which the FB-boost converter operates in boost, FB-boost and FB modes in low, medium and high input voltage regions, respectively, and for which the expression of the inductor current ripple is derived in this paper. As the input voltage in the FB-boost mode is close to the output voltage, the inductor current ripple in this mode is much smaller than that in the other modes, and the switching frequency of the boost cell in this mode can be lowered to one-(2N+1)th of the preset switching frequency to reduce the switching loss, and hence, to improve the efficiency. A 250–500 V input, 360 V output, and 6 kW rated power prototype is fabricated to verify the effectiveness of the design and control method. The average efficiency over the input-voltage range is 96.5%, and the highest efficiency attained is 97.2%. [ABSTRACT FROM AUTHOR]

In many modern energy conversion systems, a dc voltage, which is provided from a sustainable energy source or energy storage device, must be boosted and converted to an ac voltage with a fixed amplitude and frequency. In this paper, a switching pattern based on the concept of the conventional space-vector pulsewidth-modulated (SVPWM) technique is developed for single-stage, three-phase boost-inverters using the topology of current-source inverters. The six main switching states, and two zeros, with three switches conducting at any given instant in conventional SVPWM techniques are modified herein into three-charging states and six discharging states with only two switches conducting at any given instant. The charging states are necessary in order to boost the dc input voltage. The developed switching pattern was experimentally verified through a laboratory-scaled three-phase 500-W boost inverter and the results are presented in this paper. [ABSTRACT FROM AUTHOR]

The conventional current-source inverter has two major problems: unidirectional power flow and voltage boost operation, which make it impossible to be used in many applications, such as hybrid electric vehicles and general-purpose variable-speed motor drives. Z-source inverters (ZSIs) can solve both problems. Quasi-ZSIs (qZSIs) were recently proposed as an important improvement to traditional ZSIs. Besides the advantages inherited from ZSIs, qZSIs also have several of their own merits. This paper presents a comprehensive study on the new features of current-fed qZSI, including the advantageous buck–boost function, improved reliability, reduced passive component ratings, and unique regeneration capability. The current-fed qZSIs are bidirectional with an additional diode, unlike the voltage-fed ZSI that needs a switch to achieve bidirectional power flow. A modified space vector pulse-width-modulation method is proposed, and the available operating regions for motoring and regeneration operation are analyzed in this paper. Since the current-fed qZSI has the same operation as the current-fed ZSI, many results of this paper are also applicable to the current-fed ZSI. A reverse-blocking insulated-gate bipolar-transistor-based current-fed qZSI prototype was developed in the laboratory. Simulation and experimental results are shown to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper presents design and implementation of a 5-kW single-phase bidirectional inverter with wide inductance variation. For dc-microgrid applications, the bidirectional inverter has to fulfill grid connection and rectification with power factor correction to regulate the dc bus to a certain range of voltages. In the inverter operation, inductor current can vary from 0 to 32 A in one line cycle. This will result in wide inductance variation, around seven times for an inductor constructed with a molybdenum permalloy powder core, and thus, high current ripple and fluctuation. In this paper, we take into account this variation while designing controller and selecting key components to ensure inverter normal operation. Additionally, to adopt a cost-effective microcontroller for the inverter, the sensitivities of the control to various parameters are investigated and presented in this paper. Experimental results measured from a 5-kW single-phase prototype have verified the feasibility of the designed inverter. [ABSTRACT FROM PUBLISHER]

Parabolic current control is an attractive current control method with fast transient response and constant switching frequency. Due to the good dynamics of the parabolic current control, it can be employed in voltage source inverters to improve the system performance such as minimizing the distortion of current waveforms or voltage waveforms. To implement the parabolic current control, a current sensor is required, associated with the current conditioning circuit and parabolic carrier generators. Since the parabolic current control is based on the real-time information of the inductor current, any phase delay or propagation delay of the sensor itself and the conditioning circuitry, or limited resolution of parabolic carrier generators, could impact the current control performance. Since the parabolic current control compares analog signals to generate the required control signals, noise from the control board impacts the control precision as well. This paper will explore solutions to these problems. First, the inductor current of the voltage source inverter is analyzed and the parabolic current control strategy is studied, then a sensorless parabolic current control method is proposed. The new sensorless parabolic control method utilizes a current emulator to rebuild the inductor current on a microcontroller. To avoid a dc offset on the ac-side output voltage caused by the current emulator, an additional control loop in the current emulator is added. The effectiveness of the proposed methods is experimentally verified by the use of an H-bridge voltage source inverter. [ABSTRACT FROM AUTHOR]

In this paper, a novel grid-connected high step-up inverter is proposed. The topology is composed of two stages. The first stage is a single-switch high step-up dc–dc converter with bipolar outputs, and the second stage is a conventional half-bridge dc–ac grid-connected inverter. Negative grounding of the photovoltaic (PV) module has resulted in elimination of unwanted ground leakage currents in the PV system. Simple structure, employing few semiconductor switches, simple control, and high efficiency are the features of the proposed topology. Theoretical analysis and principal operation of the circuit are discussed. An experimental prototype is implemented to verify the performance of the proposed inverter. The experimental results confirm the aforementioned features and the theoretical analysis of the converter operation. [ABSTRACT FROM PUBLISHER]

Carrier-based pulsewidth-modulation (CBPWM) techniques are popular due to their simplicity, and have been widely researched for various three-phase inverter configurations. In this paper, two CBPWM techniques are proposed to reduce the common-mode (CM) voltage generated by the five-phase inverter. The five-phase inverters have more flexibility in reducing the CM voltage than their three-phase counterparts because they have more phase legs, hence finer control over the star-point voltage of the load. Two methods are proposed for the conventional two-level five-phase inverter to reduce the CM voltage; one utilizing adjacent modulating waveforms and the other utilizing nonadjacent modulating waveforms. The coupled inductor inverter (CII) uses coupled inductors to generate multilevel outputs. As the volt-second balance must be maintained across each coupled inductor, direct application of the proposed methods on the CII inverter will result in overcurrents in the coupled inductors. Hence, the proposed methods are further improved to ensure the volt-second integral over each switching period is zero. Moreover, the two proposed methods are designed to reduce switching events and prevent unexpected states occurring during the switching transitions. The performance and the switching strategy of both methods are verified by both simulations and experiments on a prototype of five-phase CII. [ABSTRACT FROM AUTHOR]

This paper proposes a novel 3 $\phi$ stand-alone solar photovoltaic (PV) system configuration that uses high-gain high-efficiency $(\approx\! 96\%)$ dc–dc converters both in the forward power stage and the bidirectional battery interface. The high-voltage-gain converters enable the use of low-voltage PV and battery sources. This results in minimization of partial shading and parasitic capacitance effects on the PV source. Series connection of a large number of battery modules is obviated, preventing the overcharging and deep discharging issues that reduce the battery life. In addition, the proposed configuration facilitates “required power tracking (RPT)” of the PV source as per the load requirements, eliminating the use of expensive and “difficult to manage” dump loads. High-performance inverter operation is achieved through $abc$ to $dq$ reference frame transformation, which helps in generating precise information about the load's active power component for RPT, regulation of ac output voltage, and minimization of control complexity. Inverter output voltage is regulated by controlling the modulation index of sinusoidal pulsewidth modulation, resulting in a stable and reliable system operation. The active power demand is controlled by regulating the dc link voltage. All the analytical, simulation, and experimental results of this work are presented. [ABSTRACT FROM PUBLISHER]

In this paper, the two-input buck converter is proposed as the dc/dc stage for photovoltaic (PV) cascaded converters. This converter is attractive for this application because it is cost effective and reliable and can achieve dual maximum power point tracking (MPPT) with only one power transistor. However, due to the simplified and integrated structure, the nonlinear characteristics of the converter and the two PV arrays complicate the control. By means of a small-signal modeling, the control theme of the two PV voltages is formulated, and the effect of the nonlinearities is presented. It is shown that, while fast voltage dynamics are achieved for the first input, the second-input voltage response depends on the second-stage converter control. Simulation and experimental results are reported to validate the theoretical analysis, showing the dual MPPT capability. [ABSTRACT FROM PUBLISHER]

This paper proposes a novel multiple-input bidirectional dc–dc power converter to interface more than two dc sources of different voltage levels. This finds applications in hybrid electric/fuel cell vehicles (FCVs), where different dc sources of unequal voltage levels need to be connected with bidirectional power flow capability. The converter can be used to operate in both the buck and boost modes with bidirectional power control. It is also possible to independently control power flow between any two sources when more than two sources are actively transferring power in either directions. The operation, analysis, and design of the converter are presented with different modes of power transfer. The proposed converter is demonstrated for FCV application using real-time hardware-in-the-loop system. Experimental results for a 5-kW system are presented, validating the theoretical analysis. [ABSTRACT FROM PUBLISHER]

The quasi-Z-source cascaded multilevel inverter (qZS-CMI) presented many advantages over conventional CMI when applied in photovoltaic (PV) power systems. For example, qZS-CMI provides the balanced dc-link voltage and voltage boost ability, saves one-third modules, etc. However, current research studies only disclosed control of single-phase qZS-CMI-based PV power systems, and there was no literature related to control of three-phase qZS-CMI-based PV power systems. In this paper, for the first time, three-phase qZS-CMI's control is proposed and demonstrated for application to PV power systems. The models of PV-panel-fed qZS H-bridge module and qZS-CMI-based PV power system are built to accurately design control algorithms for each module and the whole system. The proposed control method includes the distributed maximum power point tracking for each module, dc-link peak voltage balance control for all modules, and grid-tie control for the whole system; moreover, a new multilevel space vector modulation method is proposed for the three-phase qZS-CMI. Simulation and experimental results on a test bench with a three-phase seven-level qZS-CMI-based PV power system verify the proposed control and modulation methods. [ABSTRACT FROM PUBLISHER]

This paper proposes the modeling and controller design of an autonomous PV module (APVM) which is composed of a PV panel and a four-switch buck-boost converter (FSBBC) for series-connected distributed maximum power point tracking (DMPPT) PV system applications. The FSBBC can operate in buck, boost, and buck-boost modes with less passive component counts and noninverted output voltage polarity. The switching strategy of the FSBBC with smooth transition during mode change is explained. The parameter design criteria and the small-signal ac model of the APVM are developed. Moreover, the design of controller based on the developed small-signal ac model and the stability analysis of the APVM are presented. Computer simulation and hardware experiment results are used to verify the accuracy of the small-signal model and the controller performance of the APVM. [ABSTRACT FROM AUTHOR]

The distributed generation (DG) should supply continuous power to the local critical load, even in the condition of utility outage. And many efforts have been made for the three-phase inverter in the DG to transfer between the islanding mode and the grid-tied mode seamlessly. This paper proposes a transfer strategy based on indirect current control for the three-phase inverter in the DG, which is composed mainly of two cascaded feedback loops, i.e., capacitor voltage loop and external grid current loop, in synchronous reference frame. In the grid-tied mode, the grid current is controlled by regulating the capacitor voltage. When islanding happens, the reference of the voltage loop is fixed by the limiter. As the local load is located in parallel with the filter capacitor in the proposed strategy, the load voltage is always controlled by the capacitor voltage loop directly, and the quality of the load voltage can be guaranteed. Besides, the performance of the capacitor voltage loop is further improved by introducing an inner capacitor current loop. Moreover, the steady state and transient state of the system, including the output of the limiter, are comprehensively analyzed, and then the compensators and limiters are designed. Finally, the proposed control strategy is verified by the simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes the pulsewidth modulation (PWM) strategy of Z-source inverters (ZSIs) with minimum inductor current ripple. In existing PWM strategy with single-phase shoot-through, the shoot-through time interval is divided into six equal parts, therefore the three phase legs bear the equal shoot-through time interval. In this manner, the allotment and arrangement of the shoot-through state is easy to realize, but the inductor current ripple is not optimized. This causes to use relatively large inductors. In the proposed PWM strategy, the shoot-through time intervals of three phase legs are calculated and rearranged according to the active state and zero state time intervals to achieve the minimum current ripple across the Z-source inductor, while maintaining the same total shoot-through time interval. The principle of the proposed PWM strategy is analyzed in detail, and the comparison of current ripple under the traditional and proposed PWM strategy is given. Simulation and experimental results on the series ZSI are shown to verify the analysis. [ABSTRACT FROM PUBLISHER]

This paper presents a detailed operation analysis, controller design, and realization of a high-power, bidirectional quasi-Z-source inverter (BQ-ZSI) for electric vehicle applications. The circuit analysis shows that with a bidirectional switch in the quasi-Z-source network, the performance of the inverter under small inductance and low power factor can be improved. Based on the circuit analysis, a small signal model of the BQ-ZSI is derived, which indicates that the circuit is prone to oscillate when there is disturbance on the dc input voltage. Therefore, a dedicated voltage controller with feed-forward compensation is designed to reject the disturbance and stabilize the dc-link voltage during a non-shoot-through state. An 85-kW prototype has been built. Both simulation and experimental results are presented to prove the functionality of the circuit and the effectiveness of the proposed control strategy. [ABSTRACT FROM AUTHOR]

In this paper, an improved pulse width modulation (PWM) method for chopper-cell (or half-bridge)based modular multilevel converters (MMCs) is proposed. This method can generate an output voltage with maximally 2N+1 (where N is the number of submodules in the upper or lower arm of MMC) levels, which is as great as that of the carrier-phase-shifted PWM (CPSPWM) method. However, no phase-shifted carrier is needed. Compared with the existing submodule unified pulse width modulated (SUPWM) method, the level number of the output voltage is almost doubled and the height of the step in the staircase voltage is reduced by 50%. Meanwhile, the equivalent switching frequency in the output voltage is twice that of the conventional SUPWM method. All these features lead to much reduced harmonic content in the output voltage. What is more, the voltages of the submodule capacitors can be well balanced without any close-loop voltage balancing controllers which are mandatory in the CPSPWM schemes. Simulation and experimental results on a MMC-based inverter show validity of the proposed method. [ABSTRACT FROM AUTHOR]

This paper proposes an indirect current control algorithm for seamless transfer of three-phase utility-interactive voltage source inverters. With the proposed method the inverter is able to provide critical loads with a stable and seamless voltage during the whole transition period including both clearing time and control mode change. The LCL filter design which is suitable for the indirect current control is also proposed to meet the harmonic limits. The proposed control method is validated through simulation and experiment. [ABSTRACT FROM AUTHOR]

This paper presents a resonant single-ended-primary-inductor-converter (SEPIC) converter and control method suitable for high frequency (HF) and very high frequency (VHF) dc-dc power conversion. The proposed design provides high efficiency over a wide input and output voltage range, up-and-down voltage conversion, small size, and excellent transient performance. In addition, a resonant gate drive scheme is presented that provides rapid startup and low-loss at HF and VHF frequencies. The converter regulates the output using an ON-OFF control scheme modulating at a fixed frequency (170 kHz). This control method enables fast transient response and efficient light-load operation while providing controlled spectral characteristics of the input and output waveforms. A hysteretic override technique is also introduced which enables the converter to reject load disturbances with a bandwidth much greater than the modulation frequency, limiting output voltage disturbances to within a fixed value. An experimental prototype has been built and evaluated. The prototype converter, built with two commercial vertical MOSFETs, operates at a fixed switching frequency of 20 MHz, with an input voltage range of 3.6-7.2 V, an output voltage range of 3-9 V, and an output power rating of up to 3 W. The converter achieves higher than 80% efficiency across the entire input voltage range at nominal output voltage and maintains good efficiency across the whole operating range. [ABSTRACT FROM AUTHOR]

This paper extends the impedance-source (Z-source) inverters concept to the transformer-based Z-source (trans-Z-source) inverters. The original Z-source inverter (ZSI) employs an impedance network of two inductors and two capacitors connected in a special arrangement to interface the dc source and the inverter bridge. It has buck and boost function that cannot be achieved by traditional voltage-source inverters and current-source inverters. In the proposed four trans-Z-source inverters, all the impedance networks consist of a transformer and one capacitor. While maintaining the main features of the previously presented Z-source network, the new networks exhibit some unique advantages, such as the increased voltage gain and reduced voltage stress in the voltage-fed trans-ZSIs and the expanded motoring operation range in the current-fed trans-ZSIs, when the turns ratio of the transformer windings is over 1. Simulation and experimental results of the voltage-fed and the current-fed trans-ZSIs are provided to verify the analysis. [ABSTRACT FROM AUTHOR]

This paper proposes a new high step-up dc–dc converter designed especially for regulating the dc interface between various microsources and a dc–ac inverter to electricity grid. The figuration of the proposed converter is a quadratic boost converter with the coupled inductor in the second boost converter. The converter achieves high step-up voltage gain with appropriate duty ratio and low voltage stress on the power switch. Additionally, the energy stored in the leakage inductor of the coupled inductor can be recycled to the output capacitor. The operating principles and steady-state analyses of continuous-conduction mode and boundary-conduction mode are discussed in detail. To verify the performance of the proposed converter, a 280-W prototype sample is implemented with an input voltage range of 20–40 V and an output voltage of up to 400 V. The upmost efficiency of 93.3% is reached with high-line input; on the other hand, the full-load efficiency remains at 89.3% during low-line input. [ABSTRACT FROM AUTHOR]