Search

This paper presents a unified framework for the modeling, analysis, and design of load-independent Class E and Class EF inverters and rectifiers. These circuits are able to maintain zero-voltage switching and, hence, high efficiency for a wide load range without requiring tuning or use of a feedback loop, and to simultaneously achieve a constant amplitude ac voltage or current in inversion and a constant dc output voltage or current in rectification. As switching frequencies are gradually stepping into the megahertz (MHz) region with the use of wide-bandgap (WBG) devices such as GaN and SiC, switching loss, implementing fast control loops, and current sensing become a challenge, which load-independent operation is able to address, thus allowing exploitation of the high-frequency capability of WBG devices. The traditional Class E and EF topologies are first presented, and the conditions for load-independent operation are derived mathematically; then, a thorough analytical characterization of the circuit performance is carried out in terms of voltage and current stresses and the power-output capability. From this, design contours and tables are presented to enable the rapid implementation of these converters given particular power and load requirements. Three different design examples are used to showcase the capability of these converters in typical MHz power conversion applications using the design equations and methods presented in this paper. The design examples are chosen toward enabling efficient and high-power-density MHz converters for wireless power transfer (WPT) applications and dc/dc conversion. Specifically, a 150-W 13.56-MHz Class EF inverter for WPT, a 150-W 10-MHz miniature Class E boost converter, and a lightweight wirelessly powered drone using a 20-W 13.56-MHz Class E synchronous rectifier have been designed and are presented here. [ABSTRACT FROM AUTHOR]

In this paper, direct torque control (DTC) of five-phase induction motor (FPIM) is implemented using three-level neutral point clamped (TL-NPC) inverter. One of the advantages of three-level inverter over two-level one for DTC operation is the low torque ripple. Also TL-NPC inverter through space vector modulation technique gives low $ dv/dt$ transition with better voltage waveform. By applying conventional lookup table for DTC, the TL-NPC inverter does not ensures lower $dv/dt$ transition. In this paper, a novel switching scheme for DTC of FPIM using TL-NPC inverter is proposed that ensures the low $ dv/dt$ transition and balancing of dc-link capacitor voltages of TL-NPC inverter. To form the lookup table for DTC operation, instead of using voltage vectors directly, virtual vectors (VVs) are utilized. Two switching states are used in one sample time to generate a VV in $\alpha \beta$ plane, which gives zero resultant voltage in $ xy$ plane. The switching strategy ensures low number of transitions to reduce the switching losses. The switching state redundancies are used in a novel way to balance the dc-link capacitor voltages without using any additional hardware. The proposed technique to balance the dc-link capacitor voltage gives lower switching frequency. The MATLAB/Simulink environment is used for the simulation and the results are validated through experiments. [ABSTRACT FROM AUTHOR]

In this paper, a fixed switching frequency model predictive current controller is designed and implemented on a sensorless five-level packed U-cell (PUC5) inverter interfacing the utility. The predictive control methodology is based on a voltage vector generation technique for the cost function optimization by nullifying its derivative. The aim of the controller is to allow a fixed-frequency operation with no iterations while operating as a utility line current regulator. A pulsewidth modulator based on employing PUC5 redundant switching states fixes the PUC5 auxiliary dc bus capacitor voltage to its desired level with no necessity of a regulator; the overall technique reduces system complexity with less sensors and no loops in the predictive algorithm making it suitable for industrial applications. System discrete model is developed and experimental results verify the performance of the designed controller in making a fast response in regulating the grid current and balancing the capacitor voltage. [ABSTRACT FROM AUTHOR]

A 1-φ hybrid nine-level inverter (H9LI) topology has been proposed in this paper. The proposed H9LI topology uses a simple phase disposition pulsewidth modulation strategy to generate nine-voltage levels in the output. The main advantage of this topology is that it has a low switch count (ten switches) compared to the existing nine-level inverter topologies. To regulate the voltage across auxiliary capacitor, two innovative control techniques are proposed, which are integrated with the inverter modulation technique itself. Hence, it does not require any extra voltage balancing circuits to maintain the voltage across the auxiliary capacitor and input dc capacitors. A major advantage of these control techniques is that they eliminate the sensing of the coupled inductor current. Another significant advantage of H9LI is that loss distribution among all the power switches is more uniform compared to existing nine-level inverters. Due to low part count and absence of extra voltage balancing circuits, the H9LI achieves higher efficiency (η ≍ 94.5%) and lower cost. Furthermore, the requirement of filter size reduces due to the presence of coupled inductor in H9LI. The proposed 1-φ grid connected H9LI is verified through MATLAB/Simulink simulations and validated through experiments on a laboratory prototype of 400-VA rating. [ABSTRACT FROM AUTHOR]

Cascaded H-bridge (CHB) multilevel inverters (MLIs) have been widely used for power electronics systems. While high-voltage blocking across power switches is not a constraint for low voltage applications, the research trend has been oriented to the design of more compact module topologies as an alternative for CHB. Despite the generation of more voltage levels with reduced switch count, the existing module topologies in recent literature take no account of the freewheeling current path during dead-time, thus, inducing multistep jumps in voltage levels and giving rise to undesirable voltage spikes. Addressing this concern, this paper proposes two symmetrical compact-module topologies for cascaded MLI, where freewheeling current path during dead-time is provided for smooth transition between voltage levels to prevent voltage spikes. The proposed 7-level and 13-level compact-modules demonstrated low number of conducting switches for all voltage levels. Comprehensive analysis and comparison with the latest module topologies are conducted. To validate the operation of the proposed compact-module topologies, simulation and experimental results are presented. [ABSTRACT FROM PUBLISHER]

This paper presents a novel soft-switching galvanically isolated buck-boost dc–dc converter as a module-integrated converter for photovoltaic (PV) applications. It features three major operating modes: boost, normal, and buck mode. Their proper distribution over the input voltage range enables wide voltage regulation capabilities, i.e., close to those of nonisolated power optimizers. The proposed control algorithm requires only one buck-boost switching stage that performs voltage regulation by means of the switching stage reconfiguration with smooth transition between the modes. The design guidelines and the digital control system for PV applications are provided. The module-integrated converter was verified experimentally with a solar array simulator. The converter showed good maximum power point tracking performance and a peak efficiency of nearly 97%. [ABSTRACT FROM PUBLISHER]

In this paper, a new cascaded nonlinear controller has been designed and implemented on the packed U-cell (PUC) seven-level inverter. The proposed controller has been designed based on a simplified model of PUC inverter and consists of a voltage controller as an outer loop and a current controller as an inner loop. The outer loop regulates the PUC inverter capacitor voltage as the second dc bus. The inner loop is in charge of controlling the flowing current, which is also used to charge and discharge that capacitor. The main goal of the whole system is to keep the dc capacitor voltage at a certain level results in generating a smooth and quasi-sine-wave seven-level voltage waveform at the output of the inverter with low switching frequency. The proposed controller performance is verified through experimental tests. Practical results prove the good dynamic performance of the controller in fixing the PUC capacitor voltage for various and variable load conditions and yet generating low-harmonic seven-level voltage waveform to deliver power to the loads. Operation as an uninterruptible power supply (UPS) or ac loads interface for photovoltaic energy conversion applications is targeted. [ABSTRACT FROM AUTHOR]

A capacitor voltage-balancing method for a nested neutral point clamped (NNPC) inverter is proposed in this paper. The NNPC inverter is a newly developed four-level voltage-source inverter for medium-voltage applications with properties such as operating over a wide range of voltages (2.4–7.2 kV) without the need for connecting power semiconductor in series and high-quality output voltage. The NNPC topology has two flying capacitors in each leg. In order to ensure that the inverter can operate normally and all switching devices share identical voltage stress, the voltage across each capacitor should be controlled and maintained at one-third of dc bus voltage. The proposed capacitor voltage-balancing method takes advantage of redundancy in phase switching states to control and balance flying capacitor voltages. Simple and effective logic tables are developed for the balancing control. The proposed method is easy to implement and needs very few computations. Moreover, the method is suitable for and easy to integrate with different pulse width modulation schemes. The effectiveness and feasibility of the proposed method is verified by simulation and experiment. [ABSTRACT FROM PUBLISHER]

Hybrid cascade multilevel inverters combine semiconductor devices of different voltage ratings and technologies, which theoretically allow high efficiency to be achieved. The bottlenecks of these topologies are, however, the need for isolated supplies for the cells and the lack of modularity. This paper focuses on the design and control of high-resolution, high-efficiency multilevel inverters with simplified dc power supplies. It introduces several rules for systematically designing the dc voltages of the cells, for which all unsupplied capacitor voltages can be regulated. Six classes of inverters are obtained covering single- and three-phase, staircase and pulsewidth-modulated (PWM) inverters. New configurations of hybrid cascade multilevel inverters are obtained for each class. A double modulation strategy with two different frequencies is proposed that allows switching losses of PWM inverters to be reduced. Decoupled mechanisms are proposed for the total and internal energy balances. It is shown how to make the design robust by taking into account conversion losses and large dc-voltage imbalances in the design and control. An analysis of the maximum voltage utilization and efficiency of the resulting configurations is carried out. The effectiveness of the novel concepts is validated experimentally for two of the proposed topologies. [ABSTRACT FROM PUBLISHER]

AC test power sources are essential for testing electric equipment that is ac-mains connected. Typically, linear power amplifiers (LPAs) are mainly employed as ac test sources because of their high fidelity and excellent dynamic behavior. However, these LPAs have very high losses in their output stages, which make the systems bulky and expensive due to the large heatsinks that are required. In recent years, two approaches have attracted popular interest to improve the efficiency of ac power sources. These are hybrid operation, i.e., combination of linear and switch mode, and multilevel switch-mode inverters. In this paper, three types of multilevel power amplifiers, based on hybrid or switching technology, are presented, namely: hybrid multicell amplifier (H-MCA), amplitude-modulated (AM) + pulsewidth-modulated (PWM) MCA (AP-MCA), and PWM MCA (P-MCA). For each of these topologies, the operating principle and control scheme are introduced. Finally, a 1-kVA laboratory prototype, which can realize all the three topologies, is built, and the measured performance based on this universal prototype are compared. [ABSTRACT FROM PUBLISHER]