Search

The generation of abrasive particles is an unavoidable consequence of sliding electrical contact wear in conductive slip rings (SRs). The adhesion of abrasive particles to the insulators may lead to a decrease in flashover voltage, posing a risk to satellite power transmission. In this paper, the effect of abrasive particles on flashover is first studied. Surface abrasive particles can distort the surface electric field of the dielectric, absorb scattered electrons, and then re-emit them, thereby accelerating the development and formation of secondary electron avalanches. Flashover test results indicate that surface abrasive particles lead to a significant reduction in flashover voltage. To mitigate the impact of particle adhesion on flashover, a method of constructing particle traps on the surface of insulators is proposed. The location and structural parameters of the particle trap are further optimized and determined. The flashover test results using planar dielectric samples and SR insulator samples both demonstrate that the optimized particle trap can significantly improve the flashover voltage. The dielectric maintains high electrical strength even when particles are trapped in particle traps. The physical details of the impact of particles on flashover and the effect of particle traps are analyzed utilizing an electron movement simulation, corroborating the experiment from a microscopic aspect. [ABSTRACT FROM AUTHOR]

• Extraction of distant and soft defect time–frequency distribution surrounded by interference. • Instantaneous filtering may help detect extremely weak impedance discontinuities. • The proposed method has better location accuracy compared with traditional Wigner-Ville distribution methods. Time-frequency domain reflectometry is a highly sensitive method to locate cable defect. However, locating a potential defect far from the cable head may be less accurate because of the signal amplitude attenuation and the interference parts. To solve the problem, this paper proposes an accuracy improvement method based on instantaneous filtering in time-frequency domain. The method extracts the frequency spectrum of the time-frequency signal, and then filters the spectrum and reconstructs the signal based on the difference between the signal and interference spectra, which can eliminate the interference and improve the location accuracy. In simulation, the location error of this method improves from 5.47 % to 0.57 %. In experiment, the proposed method reduces the location errors and magnifies the location peaks of the breakage defect, thermal aging defect, and ground faults. For the defects studied in this paper, the method improves the defect location accuracy and defect amplitude detectability of TFDR. [ABSTRACT FROM AUTHOR]

• Novel rapid moisture test for oil-paper insulation. • Microstrip ring resonator analyzes dielectrics properties. • Precise moisture level distinction found. • New model assesses the moisture content accurately. Moisture ingress significantly accelerates the aging of oil-paper insulated equipment, making accurate assessment of moisture content critical for the operation and maintenance of oil-immersed insulated power equipment. In this paper, a novel method for rapid moisture content evaluation is proposed based on a microstrip ring resonator (MRR) designed with a fundamental frequency of 1.16 GHz. A calculation model for the dielectric response analysis using MRR is established to characterize dielectric properties of the material layered on the substrate. ANSYS HFSS electromagnetic simulation software was used to study the impact of dielectric material thickness and the substrate on the MRR test results. Experimental measurement demonstrated that the maximum deviation in resonance frequency was merely 0.542 %. The dielectric properties of uniformly and non-uniformly damp insulating pressboard were analyzed across the frequency band from 1 to 6 GHz. The MRR test results were compared with those of the standard resonant cavity method and frequency domain dielectric spectroscopy (FDS) test. Using the regression algorithm and curve analysis, moisture assessment models for both uniformly and non-uniformly damp oil-paper insulation were established. The experimental results show that the MRR test can clearly distinguish between the pressboard samples with varying moisture levels under uniform conditions, with a maximum moisture evaluation error of 8.19 %. The results demonstrate that the MRR test method, requiring only 56 s, can quickly and effectively evaluate the moisture content of insulating pressboard. [ABSTRACT FROM AUTHOR]

Cellulose material is a dielectric with intricate microscopic relaxation processes due to its complex structure. However, conventional models and curve fitting methods used for tracing and analyzing these processes often fail to capture crucial dielectric information. This paper aimed to extract the Distribution of Relaxation Time (DRT), the most fundamental and effective dielectric information providing the time scale and relative contribution of all microscopic relaxation processes. First, a distributed extended Debye model with infinite branches was constructed based on the microscopic nature of dielectric relaxation. Then, an implicit equation of the DRT function was established, inspired by the mathematical principles of infinite subdivision and summation. To obtain the numeral solution of the DRT function, a regularization method was proposed and validated. Finally, the approach was applied to cellulose insulating paper with varying degradation degrees. The relaxation process with a long time constant played a significant role, and variations during the degradation process were attributed to reduced activation energy. With clear physical interpretation and robust mathematical foundation, our method sheds light on the intricate dielectric relaxation processes in cellulose. This not only enhances the theoretical understanding and practical application of cellulose materials but also provides valuable insights for the analysis and application of other materials. [Display omitted] [ABSTRACT FROM AUTHOR]