Search

The intrinsic properties of nanomaterials offer promise for technological revolutions in many fields, including transportation, soft robotics, and energy. Unfortunately, the exploitation of such properties in polymer nanocomposites is extremely challenging due to the lack of viable dispersion routes when the filler content is high. We usually face a dichotomy between the degree of nanofiller loading and the degree of dispersion (and, thus, performance) because dispersion quality decreases with loading. Here, we demonstrate a potentially scalable pressing-and-folding method (P & F), inspired by the art of croissant-making, to efficiently disperse ultrahigh loadings of nanofillers in polymer matrices. A desired nanofiller dispersion can be achieved simply by selecting a sufficient number of P & F cycles. Because of the fine microstructural control enabled by P & F, mechanical reinforcements close to the theoretical maximum and independent of nanofiller loading (up to 74 vol %) were obtained. We propose a universal model for the P & F dispersion process that is parametrized on an experimentally quantifiable “Dfactor”. The model represents a general guideline for the optimization of nanocomposites with enhanced functionalities including sensing, heat management, and energy storage.

ABSTRACTThe ZrN–SiAlON composite refractory powder was successfully synthesised from zircon and bauxite minerals by the carbothermal reduction nitridation or the aluminothermic reduction nitridation method with three typical reducers, including carbon coke, carbon black and aluminium powder. The effect of reaction temperatures on phase composition and microstructure was investigated using X-ray diffraction and a scanning electron microscopy (SEM), respectively. The thermodynamics equilibrium relationships of the condensed phases were analysed as well. The results showed that carbon coke was the most optimum reducer and when it was used as the reducer, the main final products were granular ZrN with a little β-SiAlON. Nevertheless, ZrO2was produced during reduction at 1600°C when the reducer was carbon black, because the activity of carbon black was the poorest. Additionally, more byproducts were produced in the case of Al powder used as reducer at 1600°C, such as AlN polytype and Al2O3.

The ZrN–SiAlON composite refractory powder was successfully synthesised from zircon and bauxite minerals by the carbothermal reduction nitridation or the aluminothermic reduction nitridation method with three typical reducers, including carbon coke, carbon black and aluminium powder. The effect of reaction temperatures on phase composition and microstructure was investigated using X-ray diffraction and a scanning electron microscopy (SEM), respectively. The thermodynamics equilibrium relationships of the condensed phases were analysed as well. The results showed that carbon coke was the most optimum reducer and when it was used as the reducer, the main final products were granular ZrN with a little ß-SiAlON. Nevertheless, ZrO2was produced during reduction at 1600°C when the reducer was carbon black, because the activity of carbon black was the poorest. Additionally, more byproducts were produced in the case of Al powder used as reducer at 1600°C, such as AlN polytype and Al2O3.

Any industrial application aiming at exploiting the exceptional properties of graphene in composites or coatings is currently limited by finding viable production methods for large volumes of good quality and high aspect ratio graphene, few layer graphene (FLG) or graphite nanoplatelets (GNP). Final properties of the resulting composites are inherently related to those of the initial graphitic nanoparticles, which typically depend on time-consuming, resource-demanding and/or low yield liquid exfoliation processes. In addition, efficient dispersion of these nanofillers in polymer matrices, and their interaction, is of paramount importance. Here we show that it is possible to produce graphene/epoxy nanocomposites in situ and with high conversion of graphite to FLG/GNP through the process of three-roll milling (TRM), without the need of any additives, solvents, compatibilisers or chemical treatments. This readily scalable production method allows for more than 5 wt % of natural graphite (NG) to be directly exfoliated into FLG/GNP and dispersed in an epoxy resin. The in situ exfoliated graphitic nanoplatelets, with average aspect ratios of 300–1000 and thicknesses of 5–17 nm, were demonstrated to conferee exceptional enhancements in mechanical and electrical properties to the epoxy resin. The above conclusions are discussed and interpreted in terms of simple analytical models.

AbstractThis paper investigates the trade-off between low percolation threshold and large positive temperature coefficient (PTC) intensity in conductive polymer composites (CPCs). Conductive particles with low aspect ratios and large dimensions have been demonstrated to induce large PTC intensity in CPCs. Conversely high aspect ratio conductive (nano)particles like carbon nanotubes (CNTs) are desirable because of their extremely low percolation threshold (typically well below 1 wt.%), providing benefits in terms of reduced density, brittleness, costs and improved processability. Herein we report on combinations of different conductive fillers to explore the possibility to obtain both low percolation threshold and high PTC intensity. For the first time we use model systems in which at least one of the two conductive fillers is of relatively homogenous size and shape to facilitate unraveling some of the complicated inter-relationships between (mixed) conductive fillers and the PTC effect.

We have prepared composites of polyvinyl acetate (PVAc) reinforced with solution exfoliated graphene. We observe a 50% increase in stiffness and a 100% increase in tensile strength on addition of 0.1 vol % graphene compared to the pristine polymer. As PVAc is commonly used commercially as a glue, we have tested such composites as adhesives. The adhesive strength and toughness of the composites were up to 4 and 7 times higher, respectively, than the pristine polymer.

A novel class of ultra-thin fibres, which affect microbial growth, were explored. The microbial properties of poly(methyl methacrylate) fibres containing 2, 4 and 8 wt% of graphene nanoplatelets (GNPs) were studied. GNPs were dispersed in a polymeric solution and processed using pressurized gyration. Electron microscopy was used to characterize GNP and fibre morphology. Scanning electron microscopy revealed the formation of beaded porous fibres. GNP concentration was found to dictate fibre morphology. As the GNP concentration increased, the average fibre diameter increased from 0.75 to 2.71 µm, while fibre porosity decreased. Gram-negative bacteria Escherichia coliand Pseudomonas aeruginosawere used to investigate the properties of 2, 4 and 8 wt% GNP-loaded fibres. GNP-loaded fibres (0 wt%) were used as the negative control. The fibres were incubated for 24 h with the bacteria; bacterial colony-forming units were enumerated by adopting the colony-counting method. The presence of 2 and 4 wt% GNP-loaded fibres promoted microbial growth, while 8 wt% GNP-loaded fibres showed antimicrobial activity. These results indicate that the minimum inhibitory concentration of GNPs required within a fibre is 8 wt%.