Search

High-frequency (HF) oil-immersed transformers with small size and light weight have been paid wide attention by researchers. Its oil–paper insulation frequently withstands HF over-voltages at frequencies of several kilohertz and above, resulting in the too early failure of oil–paper insulation. In order to investigate the effect of HF on oil–paper insulation, this article investigates the partial discharge (PD) characteristics of oil–paper insulation under HF stress. The experimental results show that a frequency-induced inflection point is existed near 10 kHz and the PD parameters of HF voltages is much higher than that ac voltages. Besides, the theoretical mechanism is expounded to interpret and understand the formation process of frequency-induced inflection points more easily. It can be found that the change in frequency causes the change in the charge decay time constant and the residual charge on the insulating surface, resulting in the formation of the frequency-induced inflection point at HF. These results might contribute to determine the characteristics of PDs between HF voltages and ac voltages. It can provide references for the research and production of HF transformers. [ABSTRACT FROM AUTHOR]

Although the circulating flow of insulating oil can enhance heat dissipation in converter transformers, it can also influence the space charge distribution in oil–paper composite insulation. In this article, the oil–paper composite insulation between flat electrodes was used as the experimental model. Based on the pulsed electroacoustic (PEA) method, we investigated the effect of uncharged flowing oil on the space charge distribution in composite insulation under a dc electric field and polarity reversal. Under a dc electric field, as the oil flow velocity increased, the amount of interface charge between the oil and paper first increased and then decreased. During the polarity reversal process, the field distortion was aggravated at slower oil flows. These experimental results were explained in terms of the effect of oil flow on ionized charges in the oil. [ABSTRACT FROM AUTHOR]

It is known that 1,2,3 benzotriazole (BTA) can effectively limit the oil flow electrification in oil–paper insulation used in HVAC transformers, but it is still unclear whether BTA is applicable to converter transformers. Thus, the effects of BTA on interface charge behaviors and charge migration in oil–paper system under dc stress are investigated in this article. The experimental results show that BTA reduces the interface barrier between oil and oil-immersed paper by altering the charge distribution of the electric double layer (EDL) at the oil–paper interface, which is beneficial to the operation stability of converter transformers in the condition of polarity inversion. However, it is also found that the BTA additive promotes the charge accumulation at oil–paper interface and enhances the local electric field by increasing the carrier mobility of oil–paper insulation. The experimental results in this article provide references for the selection of insulating oil additives for converter transformers. [ABSTRACT FROM AUTHOR]

Voltage rise caused by high levels of distributed generation is manifesting as voltage regulation challenges for many electricity network service providers. In this environment it would be ideal to reduce supply voltage magnitudes, however, many network operators are hesitant to do so due to concerns related to consumer appliance performance at reduced supply voltage magnitudes. Voltage regulation requirements are defined by network standards and network service providers must ensure voltages remain within specified limits. Through an evaluation of domestic appliance performance when supplied at various voltage magnitudes, this paper examines the impact of varying voltage levels on residential appliances. Equipment energy demand, operation and actuation were monitored for each applied voltage magnitude. While no equipment failures were recorded, appliance behaviour varied significantly with applied voltage magnitude. Individual appliance conservation voltage reduction (CVR) factors have also been established. The results highlight the importance of good voltage regulation and provide substantiated appliance performance figures for future studies. The outcomes of this paper allow electricity network service providers to understand the implications of supply voltage magnitude on domestic appliance performance, whether it be understating of the impact of higher voltage magnitudes caused by distributed generation or implications of reducing voltage magnitudes to provide headroom for distributed generation integration. [ABSTRACT FROM AUTHOR]

The phenolic adhesive and casein adhesive are two kinds of adhesives used in pressboard block production. The partial discharge characteristics of pressboard block containing the two types of adhesives under AC, DC and AC/DC composite voltage are researched in this paper. Using the block samples with phenolic adhesive or casein adhesive, the partial discharge characteristics, flashover characteristics and the influence of the adhesive layer orientations were obtained. The results show that the use of adhesive may introduce a weak zone of insulation performance and reduce the insulation strength of the pressboard block. There exist polar effects on partial discharge and flashover characteristics under DC voltage, and there is no significant difference in the partial discharge characteristics and flashover voltages between the pressboard blocks with casein and phenolic adhesive. The phenomena are analyzed in terms of molecular characteristics of adhesives and cellulose pressboard. The research results of this paper provide significant theoretical and practical reference for the optimization of transformer insulation materials. [ABSTRACT FROM AUTHOR]

Single horizontal and vertical grounding electrodes are often used for an earth connection of the lightning protection system. However, there are many practical situations when such electrodes have to be enhanced for better efficiency and replaced by multiple horizontal, vertical and/or inclined electrodes. This paper presents a systematic approach to evaluating and comparing the lightning performance of such grounding arrangements based on simple formulas. The contributions of this paper are: It is shown that impulse impedance Z may be derived from known formulas for low-frequency grounding resistance R; a new definition of effective length is introduced that allows for such a derivation; a collection of accurate formulas for R of all considered grounding electrode arrangements is presented; and a new concept of “effective volume” is described that enables a simple procedure to increase electrodes’ effective length. The new formulas for R, Z, and effective length of the different electrode arrangements allow an analysis that might help search for a choice of cost-effective configuration and dimensions of the grounding systems in the early design stage. [ABSTRACT FROM AUTHOR]

This paper proposes a systematic method for the identification of the load circuit parameters (say the $\boldsymbol{R}$ , $\boldsymbol{L}$ , and $\boldsymbol{C}$ elements) based only on the information of the instantaneous voltage and current measured at the point of common coupling (pcc). Geometric Algebra (GA) and concepts of differential geometry are used to produce a rigorous mathematical framework. The identification is formulated as a multidimensional geometrical problem that is solved conveniently by means of GA. Once the passive elements of the load have been identified, the active and reactive powers can be computed from first electromagnetic principles (Maxwell Equations). The theory is general and is verified with linear and nonlinear circuits. The paper shows single-phase circuits but the theory can be extended to three-phase circuits. The method is easy to program and has shown to be very robust for all tested cases. Because of its generality, the method presented will find applications beyond electric circuits. [ABSTRACT FROM AUTHOR]

As the inverter-based generation replaces the conventional synchronous generators, it may also need to fill in the missing ancillary service support. One of these ancillary services is dynamic reactive power provision and voltage control. This paper analyzes optimal strategy of reactive and active fault-current support of the inverter-based generation leading to fast voltage recovery of the system. For the purpose of the analysis, new ramping active current controller able to emulate different behavior of active current injection is proposed. By optimizing its parameters for different case studies of the system, the conclusions about optimal behavior of the inverter based generation with respect to system parameters and operating conditions are drawn. It is observed that the optimal combination of active and reactive fault-current is the most sensitive to the dynamic load component penetration levels in the system. With the increasing penetration levels, the significance of active fault-current injection increases. The results show that with higher penetration levels of dynamic load component in the heavy load areas, the ramping down of the inverter-based generation active fault-current results in slower voltage recovery of the system. Following this conclusion, a recommendation on update of current European grid codes is proposed. [ABSTRACT FROM AUTHOR]

It is well known that for high voltage transmission lines in the range of 245 kV–525 kV, particularly in regions of high ground resistivity, lightning back flashover problems could be a major concern. Line arresters have been used successfully to address the problem. Underbuilt ground wires have been proposed as a viable alternative. The present paper shows that the full potential of additional ground wires could be achieved by optimizing their position on the tower. Such optimization often results in a preferred position at the level, or higher than the attachment height of the lower phase conductors; therefore the designation Embedded Ground Conductor. An essential requirement is that such positioning does not infringe in any way on the dielectric integrity of the electrical clearances and, under the influence of induced charge, does not become a source of positive streamers that may lead to additional radio or audible noise. It is found that a streamer- inhibited conductor, when properly placed, fully satisfies the above requirements. It is determined that for 245 kV, 345 kV and 420 kV lines, a streamer-inhibited embedded conductor could improve the back flashover rate by a factor of 10 or more [ABSTRACT FROM AUTHOR]

Fast and accurate power-flow methods are of great importance, especially in near real-time optimal operation of power systems. This importance will be even more highlighted in the presence of more repetitions of power-flow calculations, which cause more computational complexities in optimization problems. As a solution, in this paper, a novel fast and accurate approach of linear power-flow formulation is proposed. Principles of the proposed approach are based on dividing power-flow calculations into base and variable parts. To this aim, at first, system modeling of base and variable parts are presented. For the base-part modeling, utilizing a nonlinear power-flow, an accurate base power-flow (BPF) is extracted. Afterwards, by linearizing the power system around the BPF, variable-part model which is the result of a linear fitting process, is obtained. Then, it is shown that the variable-part of the operating point is always a function of the obtained base-part and variable-part models. In this paper, by focusing on the stochastic application of the proposed approach, different uncertainties in a distribution system are considered. Finally, numerical results carried out in the Matlab environment, for a IEEE 34-bus standard distribution system and then a 1486-bus case study, verify the performance of the proposed approach. [ABSTRACT FROM AUTHOR]

This paper presents the three-phase impulse overvoltage measured at the terminal of a 10 kV distribution line when the impulse current was injected into the phase conductor of the distribution line. The overvoltage observation station was installed at the terminal of the line to record the three-phase overvoltage waveforms. It is shown that the struck phase overvoltage consists of three components including the negative pulse, the stage of residual voltage maintenance and the overshoot oscillation part. The observed negative peak values of the struck phase overvoltage range from −85.4 kV to −96.0 kV in three different injected impulse levels at 90,120,150 kV charging voltage. The duration of residual voltage depends on the duration time of injected current. Furthermore, there is a strong positive relationship between the oscillation amplitude of the struck phase overvoltage and the injected current amplitude. The peak amplitudes of three-phase overvoltage always have the following magnitude relationship: struck phase C > induced phase B > induced phase A. The voltage coupling coefficients of induced phases will not exceed 0.4. The test method proposed in this paper will be helpful to the research on the lightning overvoltage response characteristics of the distribution line and the protection analysis of arresters. [ABSTRACT FROM AUTHOR]

The converter transformers are reported to fail generally on the thyristor-valve side, where complex alternating voltage waveforms superimposed with dc voltages would occur. The effect of these waveforms on the failure and endurance of the valve side winding insulation of the transformers is not yet understood, which is investigated here. In this paper, the voltage waveforms occurring in a converter transformer are obtained through PSCAD/EMTDC for a typical double pole ±500 kV, 1000 MW DC-link HVDC transmission system based on the CIGRE benchmark system. The waveforms are then amplified using a High Voltage amplifier for experimental breakdown investigations. Stepped-stress damage equalization method has been used for obtaining the lifetime characteristics from failure data. A comparison with life curve under pure sinusoidal and actual alternating voltages with superimposed dc and harmonic voltage has been made to understand why the converter transformers generally failed on the valve side. The results first time give fundamental reasons for the possible failure of the converter transformers and put forth important design considerations. [ABSTRACT FROM AUTHOR]

E-beam voltage contrast inspection is a very common method for in-line detection of many key defect types for rapid yield learning during technology development. Generally, the wafer surface is charged positive, but sometimes charging the wafer surface negative makes more sense. This paper reviews four advantages that negative charging may provide. Switching from positive to negative charging is typically achieved using landing energy and/or extraction voltage. A third control knob is introduced and demonstrated using three common inspection layers, contact chemical mechanical polish (CMP), 3D NAND wordline shorts and 3D NAND wordline opens. [ABSTRACT FROM AUTHOR]

The recent progress in III-nitride tunnel junction (TJ) contacts for optoelectronic devices is summarized in this review paper. Due to the rapid developments of various III-nitride based optoelectronic devices for different emerging applications, TJs are of interest for these devices to achieve more efficient device performance. This review paper first briefly describes the working principles of TJs and the advantages of employing TJs in optoelectronic devices. The significant advancements in III-nitride TJs realized by metalorganic chemical vapor deposition (MOCVD) and molecular beam epitaxy (MBE) are addressed, as well as their TJ device performances. Lastly, the critical challenges for employing III-nitride TJs in wide bandgap ultraviolet (UV) light emitters are discussed for future investigations. [ABSTRACT FROM AUTHOR]

In renewable energy micro-source applications, a wide range of voltage conversion of the step-up converter is an essential part to equalize the typical low voltage of micro-source with DC-bus voltage of Inverter or motor drives. In order to meet this purpose, an ultra-voltage gain step-up DC-DC converter is proposed in this paper. The proposed converter has made an arrangement of the regenerative-boost fed switched inductor and capacitor configurations. Thereby, due to such an organization of structure, the proposed converter can develop an extremely high voltage-gain even at lower duty ratios. In addition, it has the advantage of lower switching stress across all power semi-conductive diodes. Furthermore, this paper describes the steady-state analysis and comparative features of the converter with existing recent literature. Finally, to validate theoretical analysis and test the feasibility and suitability of the proposed ultra-gain converter, the experimental results were observed by a 500 W fabricated prototype. [ABSTRACT FROM AUTHOR]

The Rogowski coil transducer's integrator will amplify the transmission error, which may lead to mal-operation of the relay. In this paper, a novel method of line relay based on the differential output of Rogowski coil is proposed. Besides, an improved fast distance relay based on the differential output of Rogowski coil is presented. Based on the equal transfer process of transmission lines(ETPTL), the voltage signal should be processed by the virtual Rogowski coil to solve the inconsistent transfer problem between voltage and current. Furthermore, this paper also presents the reconstruction method of voltage at the fault point and the least-square algorithm to solve the R-L differential equation, so as to improve the algorithm accuracy. Furthermore, the equal transfer process error of the virtual Rogowski coil is analyzed in the paper, and the design principle of low pass filter is also proposed. Simulation results and experiment results demonstrate that the improved fast distance relay scheme has high operation speed, which is signed prior to other distance relay schemes. The proposed method also provides a valuable reference for other types of transmission line relay based on Rogowski coil transducer. [ABSTRACT FROM AUTHOR]

This paper establishes an instantaneous voltage model to illustrate the dynamic characteristics of grid voltage in electromagnetic time scale affected by power-electronic interfaced voltage regulatory devices with two typical categories of control systems, i.e., power-current cascading control and power synchronization control, exemplified by the STATCOM and virtual synchronous condenser (VSCON) respectively. In this paper, a linearized instantaneous voltage model is firstly established to analyze the impact paths of control loops in the STATCOM and VSCON. Based on the model, the dynamic process of grid voltage is divided into three stages. Various factors on the dynamic process of grid voltage are analyzed, especially cascading control loops prior to the functioning of AC voltage control. Moreover, stiffness characteristic is proposed to evaluate the effects of power electronic interfaced voltage regulatory devices with different control structures. In addition, the effectiveness of the stiffness compensation based on the VSCON is validated by the study cases. [ABSTRACT FROM AUTHOR]

Protection of microgrids at the Point of Interconnection (POI) is a challenging task. Particularly, single-line-to-ground (SLG) faults on interconnection lines are difficult to detect using the fault current detection relays if the microgrid is ungrounded at utility side of its interconnection transformer; such microgrid contributes very low fault current, which disappears once the utility feeder breaker opens. Other common schemes for protection of microgrid interconnection line against SLG faults include Direct Transfer Trip (DTT) and over-voltage relay (59G). The main challenges associated with these methods are installation and maintenance costs of high-speed communication system, sensitivity of relay settings, and delayed fault clearing time due to selectivity requirements. To address such concerns, this paper proposes the use of a distance relay at the microgrid/LV side of the interconnection transformer to provide protection against SLG faults on the interconnection line at the utility/HV side. The designed distance relay executes an enhanced apparent impedance calculation using residual voltage compensation to correctly detect the fault, properly measure the fault location, and timely isolate the fault. In this paper, various scenarios are analyzed using ASPEN and PSCAD simulation tools to demonstrate the effectiveness of the proposed method for protecting the microgrid interconnection line under different fault scenarios. [ABSTRACT FROM AUTHOR]

The inrush current generated by power transformer energization (TE) causes voltage sag of the nearby bus, the typical residual voltage of the voltage sag caused by transformer energization (VSTE) is about 0.7 p.u.--0.9 p.u. and lasts for a longer duration, which may lead to the sensitive equipment trips. This paper proposes an estimation method of voltage sag frequency considering VSTE. Firstly, based on the maximum entropy method, the residual flux distribution is calculated by considering the relationship between the residual flux and closing angle at the moment of TE. The voltage sag waveform caused by TE is calculated based on the estimation of the probability distribution of residual flux, to evaluate VSTE objectively and comprehensively. Secondly, this paper proposes a non-rectangular voltage sag equivalent frequency statistical method based on multiple magnitude-duration (MMD) function, to avoid the overestimation of voltage sag frequency by the traditional methods. Furthermore, this paper proposes an assessment algorithm of voltage sag frequency. Finally, the simulation of IEEE-30 test system verifies the necessity and correctness of the proposed method. [ABSTRACT FROM AUTHOR]

Autonomous power systems with a single power station and a high-voltage (HV) network may be susceptible to overvoltage instability, especially during light-load conditions. Moreover, in low inertia systems, considerable frequency excursions may be observed after disturbances. To deal with voltage and frequency stability problems in such isolated power systems, several measures should be taken, such as rules for adequate automatic voltage control of the synchronous generators and load-tap-changers (LTCs), and/or adequate design of actions applied during emergency system conditions such as reactors switching, and redesigning underfrequency load shedding taking into account overvoltage problems. The effectiveness of the proposed countermeasures against overvoltage instability in autonomous power systems is illustrated in this paper. In 2016, the autonomous power system of the Greek island of Rhodes experienced similar voltage/frequency problems leading to a blackout. This event has been accurately reconstructed in this paper. The application of the suggested countermeasures during the simulation of the 2016 blackout event in Rhodes, further highlighted the effectiveness of these measures, providing a guideline for similar cases. [ABSTRACT FROM AUTHOR]

Electrical equipment of the floating nuclear power plant operates in a long-term vibration environment. Ground faults occur frequently and are often accompanied by arc, a reliable arc suppression algorithm for the generator stator winding is necessary. In this paper, an active arc suppression method is proposed by connecting a controllable voltage source to the generator neutral point. Through regulating the neutral point voltage to be equal in amplitude and opposite in phase to the fault potential, the fault point voltage can be clamped to a low level to achieve arc suppression. Since the generator's phase potential contains certain harmonic components, the controllable voltage source includes fundamental and third-order harmonic components. To accurately calculate the output voltage, online calculation methods for the fault location, fault potential and grounding capacitance are proposed. The accuracy of the fault location method is verified by simulation and dynamic test. And simulation results based on PSCAD/EMTDC software show that the proposed method can achieve effective arc suppression at different ground fault conditions. [ABSTRACT FROM AUTHOR]

The Ultra High Voltage (UHV) converter transformer may generate serious inrush current during closing. It will cause commutation voltage distortion and easily result in commutation failure of converters on the same commutation bus. Due to the change of flux amplitude and phase caused by closing resistance in the Ultra High Voltage Direct Current (UHVDC) system, it is difficult to determine the closing time of the converter transformer when considering the influence of residual flux. Therefore, this paper first analyses the existing closing resistance strategy, and constructs the magnetic bias function according to the influence characteristics of closing resistance on the flux and phase. Then an inrush current suppression strategy based on magnetic bias simulation is proposed for star connection and delta connection of UHV converter transformers, which can accurately calculate the ideal closing time of mutual cancellation between the residual flux and bias flux during closing. Finally, the no-load closing model of the UHV converter transformer is established by PSCAD/EMTDC for simulation analysis of the feasibility, real-time verification is carried out using the RTDS closed-loop experimental platform. The results show that the proposed inrush current suppression strategy can effectively suppress the inrush current under different residual flux conditions. [ABSTRACT FROM AUTHOR]

In actual line-commutated converter based high- voltage direct-current (LCC-HVDC) projects, multiple HVDC transmission lines are usually installed on the same tower to save transmission corridors and reduce construction costs. However, electromagnetic coupling effect between adjacent lines can cause commutation failure (CF) in the non-fault poles when a line or pole fails. Hence, this paper deeply investigates the mechanism and the prevention strategy of CFs caused by line coupling effect in single- and double-circuit HVDC systems. The influencing factors of line coupling effect and the coupling characteristics under fault conditions are analyzed first based on the modeling of parallel transmission lines and the traveling wave theory. Then the mechanism of CF caused by line coupling effect is investigated with the consideration of different fault conditions, different line structures, and different system operation modes. Based on the above analyses, prevention strategies for CFs of non-fault poles in single- and double-circuit systems are proposed. Finally, the simulation results verify the correctness of the theoretical analyses and the effectiveness of the proposed control strategies. [ABSTRACT FROM AUTHOR]

The increasing penetration of distributed renewable energy sources drastically alters the dynamic characteristics of distribution networks (DNs). Therefore, several equivalent models have been recently proposed, to analyze more accurately the complex behavior of modern DNs. However, relatively simple models are still commonly used in practice for dynamic power system studies. In addition, dynamic equivalent models for DNs are sensitive to different operating conditions and there is lack of systematic understanding of their performance. Scope of this paper is to propose a methodology for identifying the applicability range in terms of accuracy and generalization capability of several conventional and newly developed equivalent models for the dynamic analysis of modern DNs. A set of metrics is used for the modelling accuracy assessment and a sensitivity analysis framework is introduced to fully quantify the generalization capabilities of DN equivalent models. Based on the above, guidelines and recommendations for the development of robust equivalent models for DN analysis are proposed. [ABSTRACT FROM AUTHOR]

Multilevel converters (MLCs) are pioneers in the field of electrical energy conversion. From the classification of MLCs, modular multilevel converter (MMC) is top-rated due to its attractive structure and performance. The modular nature and no need for isolated DC resources are two significant advantages of this converter. However, the need for many sensors to control its performance is a considerable drawback. In addition, the internal circulating current in the MMC causes losses, decreases efficiency, and increases the voltage ripple of capacitors. This paper proposes combining a new capacitor voltage sorting method and an open-loop controller based on arms energy estimation to control the MMC using two voltage sensors in the arms and one current sensor at the output. The proposed method ensures continuous voltage balancing of the capacitors and removes multiple voltage sensors from sub-modules (SMs). The simulation and experimental results verify the accuracy and effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

Negative-sequence current is required to be intentionally injected to support the power grid or compensate the imbalanced load in asymmetrical faults utilizing STATCOM. However, the extreme compensation range of negative-sequence current injection becomes complicated when grid voltage becomes asymmetrical. This article presents a novel off-line strategy for negative-sequence current compensation under two typical kinds of asymmetrical grid faults — single-phase voltage drop and double-phase voltage drop, with the following two benefits simultaneously: maximizing negative current compensation capacity; avoiding iterations and reducing computation burdens. In this paper, the mechanism of DC voltage balancing among three phases in STATCOM is analyzed and a new identification method of negative-sequence current compensation range is explored out. To simplify the calculation, this paper takes the ratio of negative-sequence reactive (Iq-) and active (Id-) current as a variable (s). In this way, the relationship between the extreme compensation range, asymmetrical voltage sag depth of power grid h is drawn with MATLAB. Different from the previous iterative method, the off-line identification method is applied to avoid huge iterations. By fitting the curve, the precise ranges of negative-sequence current compensation under different asymmetrical grid faults are approximated as simple polynomials, thus significantly reducing the computation burdens. Simulation and experimental results verify the practicability of the proposed compensation method. [ABSTRACT FROM AUTHOR]

The ever-increasing integration of non-dispatchable distributed generation, i.e., renewable energy sources (RES), arises new challenges in the field of power system's reliability. Distribution network reconfiguration (DNR) is a cost-effective approach for the distribution system operator (DSO) that wishes to enhance system's reliability without infrastructure upgrades. This paper introduces a novel path-based mixed-integer second-order cone programming model to optimally solve the reliability-oriented DNR problem. The DSO's objectives that are optimized are: a) improvement of distribution system's reliability indices and b) minimization of power losses. The proposed model is enriched with a scenario-based stochastic programming formulation that considers multiple levels of load and RES production. The standard 33-nodes distribution system and a real-world 83-nodes distribution system are employed to prove the efficiency and applicability of the model. Firstly, the multi-objective nature of the reliability-oriented DNR problem is investigated by conducting a sensitivity analysis, which reveals a trade-off region between reliability indices and power losses. Moreover, the obtained results show different global optimal solutions when the variability of load and RES production is considered. This highlights the importance of considering a scenario-based approach for load and RES production when solving the reliability-oriented DNR problem. [ABSTRACT FROM AUTHOR]

This paper widens the application of a testing protocol for overhead line insulators introduced by TERNA. Testing results relevant to three groups of Room Temperature Vulcanized pre-coated cap-and-pin insulators removed from High Voltage Alternate Current and Extra-High Voltage Alternate Current Italian lines after different years of service are reported and statistically processed; the third group is treated here for the first time and new results for the other two groups are included. Among the various tests prescribed in the protocol, focus is on the Quick Flashover test, with the aim to examine and compare the flashover voltages of all three groups as a function of service time. The dependence of flashover voltage on electric field is also analyzed and a model correlating flashover voltage with field and time is proposed for the first time. It is confirmed that the flashover voltages provided by the Quick Flashover test can be considered as a diagnostic property of Room Temperature Vulcanized insulators, as they drop with the ageing time and the electric field. [ABSTRACT FROM AUTHOR]

Battery energy storage system (BESS) plays an important role in solving problems in which the intermittency has to be considered while operating distribution network (DN) penetrated with renewable energy. Aiming at this problem, this paper proposes a global centralized dispatch model that applies BESS technology to DN with renewable energy source (RES). The method proposed in this paper aims to minimize the power purchase cost considering network active loss cost as well as voltage deviation penalty cost. Later, second-order cone programming (SOCP) method as well as big M method are applied to make the problem tractable. Last, the method illustrated in this paper is applied and validated on a modified IEEE 33-bus benchmark system to verify the effectiveness of the proposed scheduling model. [ABSTRACT FROM AUTHOR]

Although Switched Reluctnace Motors have many advantages, vibration is known as their most severe drawback acting as an impediment limiting their widespread use in industrial and domestic applications. Through electromechanical relationships, it is shown that the first-order time derivative of applied phase voltage and second-order time derivative of radial force directly affect the amplitude of generated vibration, especially at the beginning of demagnetization instance. Therefore, a set of criteria is stated in this paper meeting which ensures having low vibration intensity. In this paper, three types of demagnetization voltages are proposed which comprehensively meet the stated criteria. These voltages share the same characteristics contributing to the vibration reduction in Switched Reluctance Motor. Two vital parameters of Synchronous Counter and Coefficient are included in the proposed demagnetization voltages which must be meticulously chosen in order to be effective. Noticeable contribution of the proposed methods to the vibration alleviation is validated through simulation and experimental tests conducted under different working conditions. [ABSTRACT FROM AUTHOR]

In this paper, an electro-thermal based surface charge accumulation model is established. Heat conduction, heat convection and heat radiation are included. The gas flow is coupled with fluid equations to describe the motion of charge carriers, and gas current density is also corrected by the gas velocity. In terms of it, the surface charge and electric field on a basin-type insulator in vertical laid DC gas insulated switchgear (GIS) and gas insulated transmission line (GIL) under different temperatures and pressures are studied. The results show that a temperature gradient is formed in the gas from top to bottom in the vertical direction, and the increase in pressure leads to a higher temperature of the lower surface. The surface charge density and tangential electric field increase with the temperature and decrease with the pressure. As a comparison, the surface charge and tangential electric field are calculated without considering temperature and without considering heat convection. The former leads to a lower tangential electric field than this model, while the latter brings about a higher electric field. This paper provides a more accurate reference for the design of DC GIS/GIL through a more comprehensive model. [ABSTRACT FROM AUTHOR]

Ensuring long-term voltage stability is critical for reliable operations of power grids. High share of distributed energy resources (DERs) can create complicated system operation modes that may invalidate the traditional long-term voltage stability analysis based on typical operation modes. To address this challenge, this paper investigates how to compute the shortest path to the voltage stability boundary in the DER aggregated load space with large dispersion. Instead of working in the Euclidean space, we establish the analysis and computations on the algebraic power flow manifold to better capture the curvature change of the shortest path along the direction of losing stability. A modified optimal control framework is presented for obtaining the ground-truth of the smooth shortest path on the manifold. To efficiently and accurately solve for the shortest path, we further leverage the geometric features of the power flow manifold and propose a tri-sectional approximation model that is scalable for large-scale systems. Several numerical examples, up to the 1354-bus system, with different DER penetration levels and high dimensional renewable power injection variations are evaluated. The simulation results demonstrate that the tri-sectional approximation achieves high accuracy and efficiency to approximate the shortest path to the voltage stability boundary. [ABSTRACT FROM AUTHOR]

The loss of small signal stability under parameter variation (e.g., fluctuation of loads and wind powers) can be ascribed to local bifurcations, i.e., saddle-node, Hopf, singularity-induced, and limit-induced bifurcations. Classic bifurcation calculation methods like the direct method and continuation method can only provide a bifurcation point or two-parameter bifurcation curve. Based on Galerkin method and the implicit function theorem, this paper proposes accurate polynomial approximations of bifurcation hypersurfaces in the multi-dimensional parameter space of interest. The proposed method can ensure high accuracy in this parameter space, and thus is preferable to the existing Taylor expansion-based local approximation method, given the intrinsic large-variation characteristic of wind powers. Acquired bifurcation hypersurfaces are immediately used to construct the small signal stability region of the continuous system, and then compute the stability margin for the operating point subjected to uncertainty of wind generation. Besides, the validity scope of the proposed method is analyzed, and the handling of limit-triggered equation switching as well as its computational difficulty is discussed. Computational results on the two-parameter 11-bus two-area and six-parameter IEEE 145-bus test systems validate the high accuracy and effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

In this paper, a self-adaptive protection system is proposed for adjusting the time dial (TD) of reclosers found in electrical power distribution systems (EPDSs). The self-adjustment is carried out in both phase and ground protection. The methodology considers the fuses along the feeder to obtain the fuse-saving philosophy. This feature allows less interference on the protection system already implemented by the electrical power distribution utilities. This methodology also allows using other frameworks, such as the estimation of the fault distance. The software used for computer modeling and simulation was PSCAD™/EMTDC™. The flexibility provided by the method, which allows the incorporation of new logic and changes in decision-making, resulted in an adaptive method with a good performance against different locations, types, and fault impedance. It also resulted in better coordination between the protection devices (PDs). The results compared with well-coordinated conventional protection have shown significant performance gain with the adaptive system. [ABSTRACT FROM AUTHOR]