Search

Previous concepts for solar power satellites have used conventional-technology photovoltaic arrays feeding a power collection and transmission system connected to microwave tubes used in a phased array antenna. This paper proposes using thin-film photovoltaics with an integrated solid-state phased-array to design an ultra-lightweight solar power satellite. The enabling technologies, conceptual designs, possible applications, and development steps are discussed. As these technologies evolve, their use results in a potential reduction in weight by a factor of ten to a hundred over conventional concepts for solar power satellites, and increases the utility by allowing service to smaller receivers at multiple receiving sites.

A study to determine the feasibility of providing long-term electrical power to the moon's surface by beaming power from satellites is reported. The model used to develop the reference designs are described, and the major system tradeoffs and reference design characteristics are discussed. The beam power masses and the lunar surface power system masses are compared. In some cases, the beam power system have a quarter of the mass of surface power systems, but the beam power satellites have large space structures that may present complex transportation, deployment, pointing, and control problems.

A material outgassing test consists of an effusion cell, mass spectrometer, and thermally controlled quartz crystal microbalance (TQCM). The material sample is placed in the effusion cell at a predetermined temperature, and the sample is outgassed in a vacuum of 0.000001 torr range. The total outgassing mass as a function of time is determined with the TQCM which is cooled to LN2 temperatures. Based on the view factor of the TQCM, the total outgassed mass can be determined. The technique can be verified by comparing the results to the actual mass loss of the sample which is determined by hanging the diffusion cell from the Cohn microbalance. The mass spectrometer can be used to determine if there are any low molecular weight components outgassing, such a nitrogen which does not condense on the TQCM. After the material outgasses to a point of saturation, the effusion cell is closed off, and the TQCM is slowly heated to allow the condensed film to be broken down into its components. As the temperature is increased, the components evaporate from the surface at a different rate and can be detected with the mass spectrometer. The relative amount of each component is found by the change in frequency of the TQCM as the component evaporates. Hence, from this test, not only is isothermal kinetic data obtained, but the primary components can also be identified in terms of their molecular weight.

At Stand-Alone Photovoltaic (SAPV) power systems increase in size and load diversity, the design and simulation of control subsystems takes on added importance. These SAPV systems represent 'mini utilities' with commensurate controls requirements, albeit with the added complexity of the energy source (sunlight received) being an uncontrollable variable. This paper briefly describes a stand-alone photovoltaic power/load system computerized simulation model. The model was tested against operational data from the Schuchuli stand-alone village photovoltaic system and has achieved acceptable levels of simulation accuracy. The model can be used to simulate system designs although with probable battery modification.

The present investigation is concerned with the formulation of energy management strategies for stand-alone photovoltaic (PV) systems, taking into account a basic control algorithm for a possible predictive, (and adaptive) controller. The control system controls the flow of energy in the system according to the amount of energy available, and predicts the appropriate control set-points based on the energy (insolation) available by using an appropriate system model. Aspects of adaptation to the conditions of the system are also considered. Attention is given to a statistical analysis technique, the analysis inputs, the analysis procedure, and details regarding the basic control algorithm.

The voltage current (V-I) characteristics of the photovoltaic array were studied under actual environmental conditions. A method of data acquisition was devised that uses a capacitor charge technique to obtain the V-I characteristic and a computerized data system to display, record and process the data. The capacitor charge technique uses an array shorting transistor and a capacitor bank to sweep the array operating voltage and current from short circuit to open circuit in a specified time (approximately 125 ms). The computerized data system is synchronized with this transition and repetitively samples the array voltage and current during the transition and records the ambient conditions. This data is then normalized by the computer to standard conditions (100 mW/sq cm, 28 C) and is available in tabular and graphic form for both the voltage current and voltage power characteristics. The capacitor charge technique is described.

NASA tests results from an 18 mo program of cleaning silicone-encapsulated and glass fronted solar cell panels in urban and desert environments to examine the effects of cleaning on module performance are reported. The panels were cleaned on weekly, monthly, quarterly, or semi-annual basis, while other panels of the same construction were not cleaned and served as controls. Commercially-available detergents and city water were employed for the tests, and the measurements were maintained of the modules' continuing short-circuit current output. The decay of the output was determined by least square regression analyses. Performance degradation was noticeably less in glass covered, rather than silicone-encapsulated modules which decayed faster in urban than in desert environments. Lower frequency cleanings are recommended where labor costs are high.

Progress is reported in formulating energy management strategies for stand-alone PV systems, developing an analytical tool that can be used to investigate these strategies, applying this tool to determine the proper control algorithms and control variables (controller inputs and outputs) for a range of applications, and quantifying the relative performance and economics when compared to systems that do not apply energy management. The analysis technique developed may be broadly applied to a variety of systems to determine the most appropriate energy management strategies, control variables and algorithms. The only inputs required are statistical distributions for stochastic energy inputs and outputs of the system and the system's device characteristics (efficiency and ratings). Although the formulation was originally driven by stand-alone PV system needs, the techniques are also applicable to hybrid and grid connected systems.

Stand-alone photovoltaic systems have been modeled and analyzed from sunlight in to consumer product out. By including the consumer product in the analysis, concepts such as 'product storage' (a storage tank for water or cold-plates for refrigeration) and loads controllable by the system controller have been added to the system analysis. From a controls analysis viewpoint, this adds state variables to the system. The result is that the system controller can make operating control decisions on the energy flow between these various system elements to optimize system performance and reduce system cost. The effects on system performance of various control schemes employing these concepts are presented. Analysis of water pumping and/or refrigeration systems show possible performance improvements of greater than 15% with the addition of controllable loads with product storage.

The facility was designed and built and is being operated as a national facility to serve the needs of the entire DOE National Photovoltaic Program. The object of the facility is to provide a place where photovoltaic systems may be assembled and electrically configured, without specific physical configuration, for operation and testing to evaluate their performance and characteristics. The facility as a breadboard system allows investigation of operational characteristics and checkout of components, subsystems and systems before they are mounted in field experiments or demonstrations. The facility as currently configured consist of 10 kW of solar arrays built from modules, two inverter test stations, a battery storage system, interface with local load and the utility grid, and instrumentation and control necessary to make a flexible operating facility. Expansion to 30 kW is planned for 1978. Test results and operating experience are summaried to show the variety of work that can be done with this facility.

The installation date, system and location, and solar arrays are tabulated.