Search

• The flow and heat transfer characteristics of single and multiple-synthetic jet impingement cooling is presented. • The equivalent Reynolds and Nusselt numbers were determined for the purpose of describing multiple orifice configuration. • The merging jet process is presented and the merging point is determined. In this paper, the comparison between synthetic jet actuator with single axisymmetric orifice and multiple axisymmetric orifices is presented. The aim of this paper is to compare the flow and heat transfer characteristics of single and multiple synthetic jet impingements cooling. The multiple orifice configurations had a central orifice and a satellite orifices placed in the pitch circle. The synthetic jet actuator had central orifice with 0, 3, 4, 5 and 6 orifices placed in the diameters of the relative pitch circle p / d = 2.5, 3 and 4. A total of 13 various geometric configurations were tested experimentally. In the multiple orifice configurations, the total cross-section area was approximately equal to the cross-section area of the single orifice configuration. The input power delivered to the synthetic jet actuator was maintained constant and equal to 3.00 W. The synthetic jet actuator energetic efficiency, Reynolds number, equivalent Reynolds number, radial and axial distributions of pressure coefficient, and heat transfer characteristic were presented. The synthetic jet issuing from multiple orifice plate merged at some axial distance, creating a single axisymmetric jet. The merging jet axial distances were determined for all investigated configurations. In the present paper, the integral quantities averaged over all orifices cross section area, or over impingement plate much larger than total orifices area, were analyzed for the purpose of objective comparison. From all various investigated parameters obtained from five different and independent experimental methods, the following conclusion may be made: if the total orifice cross section area in the case of single and multiple orifice synthetic jet is similar and real power deliver to the SJA is maintained at the same level the resulting equivalent Reynolds number and equivalent dimensionless stroke length achieved similar values and the impinging jet equivalent Nusselt number also achieved comparable values and distributions. [ABSTRACT FROM AUTHOR]

Jet impingement cooling is usually used in zones with extremely high thermal loads. The major factor that limits impingement heat transfer uniformity is the crossflow. The impingement cooling with return hole is applied to reduce the negative effect of crossflow on the target surface heat transfer in present paper. The influences of jet-to-plate spacing (H / D), impingement target surface curvature (α), temperature ratio (TR) and Reynolds number on flow field and heat transfer performance are investigated in detail. The results indicate that the correlation between the overall area average Nusselt number of target surface and H / D , the overall area average Nusselt number decreases by approximately 5.76% with H / D increases by one unit. Increasing the impingement target surface curvature is beneficial to expand the spanwise heat transfer. The overall area average Nusselt number increases by 295.5% for Reynolds number varying from 10,000 to 50,000 at TR = 0.910, and the overall area average Nusselt number increases by 8.68% for the TR varying from 0.668 to 0.910 at Re = 30,000. The results indicate that impingement cooling with return hole can achieve high heat transfer coefficient and uniform heat transfer distribution. [ABSTRACT FROM AUTHOR]

• New correlation between stagnation point nu and local re numbers during synthetic jet impingement heat transfer has been proposed. • The axial distribution of flow parameters under free and impinging synthetic jet reaches maximum at x / d ≈ 2. • The real (unmodified) axial distribution of stagnation nu number has been estimated. The paper presents the results of experimental investigations of heat transfer coefficients, velocity and pressure distributions of synthetic jets for two cases: constant Reynolds number and variable Stokes number and vice versa. Measurements were made for synthetic jet Reynolds number in the range of Re =5440–11,475, dimensionless stroke length L 0 =7.49–38.5 and dimensionless jet-to-plate spacing x / d = 0–20. The synthetic jet time-averaged and momentum velocity as well as the pressure for each case are presented. The centerline turbulence intensity and the Euler number are also reported. The centerline heat transfer coefficient distributions are compared with the distributions of the various velocity and pressure parameters. A new correlation between the local Nusselt number and the local Reynolds number is presented. Under synthetic jet impingement cooling the maximum of the stagnation point heat transfer coefficient appears mostly at axial distance of x / d ≈ 5. The location of the maximum Nusselt number at x / d ≈ 5 is caused by the modification of the heat transfer distribution due to the recirculation of hot air. With the decrease of the heat power released into the control volume by the impingement plate (heater) this modifying effects becomes less pronounced thus the maximum of the heat transfer coefficient shifts towards the location of about x / d = 2. The maxima of various flow parameters are generally observed at about x / d = 2 what was also reported by other independent researchers. Thus, it may be concluded that the purely mechanical phenomena does not full coincide with thermal ones in the case of synthetic jet impingement cooling. [ABSTRACT FROM AUTHOR]

• A combined experimental and numerical study for single and a row of threedimensional wall jets have been performed. • Four low Reynolds number turbulence closure models are accessed to select the suitable model that predicts the fluid flow and heat transfer characteristics of the three-dimensional wall jets accurately. • Measurement of flow characteristics like mean velocity profiles, growth of half jet widths, and velocity decay has also been performed. • For a fixed mass flow rate, at a given diameter, a smaller number of jets have higher heat transfer performance than that of the closely spaced jets. • Correlations are developed to predict local and average Nusselt numbers accurately. This paper reports the results of experimental and numerical studies to understand the heat transfer characteristics of three-dimensional wall jets exiting from a single and a row of circular jet openings over an unheated flat plate. Infrared thermography is employed to obtain the temperature distribution over the target surface, and the semi-infinite approximation methodology is used to estimate the heat transfer coefficients. Single wire constant temperature hot-wire anemometer is used to measure the flow characteristics. Additionally, computational studies have been performed to select a suitable low Reynolds number turbulence closure models among the following models, namely (i) Spalart Almaras (SA) (ii) Realizable k-ε with enhanced wall treatment (RKE-ewt) (iii) k- ω SST and (iv) Reynolds Stress Model with enhanced wall treatment (RSM-ewt) that predicts the experimentally obtained results for heat transfer characteristics accurately. Based on the investigations carried out, it is observed that RKE-ewt turbulence closure model is not only accurate but also faster in the prediction of heat transfer coefficient. Further, it is also seen that for a fixed mass flow rate, and at a given diameter of the jet opening, widely spaced jets show higher heat transfer coefficients. Furthermore, for a row of three-dimensional wall jets correlations based on the numerical results are developed for the Nusselt number for a Reynolds number range of 5000 to 15000. [ABSTRACT FROM AUTHOR]

The paper presents experimental studies on heat transfer phenomena which occurs during the impingement cooling with the use of synthetic jet. The synthetic jet was created by a special actuator consisting in a plexiglass cavity and a loudspeaker. An air was a working fluid. The effect of synthetic jet actuator geometry and supply parameters on heat transfer enhancement has been investigated. The experiment was performed with the use of classical thermal balance method. Heat transfer coefficients at a stagnation point have been obtained. Measurements were carried out in the range of excitation frequency f = 5 ÷ 600 Hz and of root mean square voltage E = 1, 2, 3, 4, 6 V. Changes of actuator geometry included: orifice diameters d = 9, 15, 24 mm, orifice thickness t = 3, 5, 20 mm and cavity depth H = 20, 40, 60 mm. On the basis of measurements results the correlations for the stagnation point Nusselt number of an axisymmetric impinging synthetic jet characterized by large Reynolds numbers have been obtained. Nusselt number has been determined in the function on scaling parameters: Reynolds number, jet-to-surface spacing x/d and the dimensionless stroke length L 0. Reynolds numbers were ranging from 3600 to 22950, x/d = 1 ÷ 20 and L 0 = 0.84 ÷ 170.5. The scaling parameters have significantly extended the range of research so far. The obtained Nusselt number correlations provide heat transfer calculations at large Reynolds numbers and are expected to have practical applications. [ABSTRACT FROM AUTHOR]