Search

Inefficient extracellular electron transfer within bioanode leads to low current production by microbial fuel cell (MFC). In this study, magnetite was sprinkled in electroactive biofilm with the aid of magnet field. Magnetite located inside biofilm (interior-doped biofilm) facilitated the electron delivery of electroactive bacteria far away from electrode surface. Electron transfer efficiency was improved by 12% and 37% compared with that of biofilms with magnetite located at the interface of biofilm/electrode (surface-doped biofilm) and that without any magnetite (control biofilm) respectively. The output power density of MFC with interior-doped biofilm (764 ± 32 mW m −2 ) was greatly increased compared with that of MFCs with surface-doped biofilm (604 ± 22 mW m −2 ) and control biofilm (475 ± 12 mW m −2 ). SEM images showed that magnetite evenly distributed inside the interior-doped biofilm and penetrated the electroactive biofilm, which would facilitate extracellular electron transfer across electroactive biofilms and thus improving the bioelectricity production. [ABSTRACT FROM AUTHOR]

Membrane biofouling in membrane bioreactor (MBR), resulted from microbes and their associated extracellular polymeric substances (EPS), is a primary challenge for wide application of MBR. However, the dynamic change of microbes attached on membrane remains little understood. In the study, a pilot MBR was constructed to estimate the effects of online chemical cleaning on membrane biofouling and meanwhile to study the microbial compositions and dynamic change before and after online chemical cleaning. Results showed that the trans-membrane pressure (TMP) increased with running time and online chemical cleaning temporarily eased TMP. Using the scanning electron microscopy, it was clearly observed that the microbes adhered into the EPS and formed biofilm before online chemical cleaning, and the biofilm was disrupted and most microbes on the membrane surface were removed after online chemical cleaning. EPS assay results showed that online chemical cleaning removed most protein and humic substances, but only a little part of polysaccharide. Microbial phylogenetic cluster displayed that some microbes attached on the membrane were clustered together and obviously separated from those in the mixed liquor sludge, indicating the special property of the microbes on the membrane. The microbial community dynamic analysis demonstrated that the dominant group on the membrane was changed from Burkholderiaceae to Flavobacteriaceae and Saprospiraceae after online chemical cleaning. Furthermore, some microbes such as Acinetobacter , Xanthomonas , Cloacibacterium and Flavobacterium were found to repeatedly cause the membrane fouling. The results might be helpful for developing biological-based cleaning method and antifouling strategies in the future. [ABSTRACT FROM AUTHOR]

As serious water ecological pollution caused by toxicant leakage occurs frequently, early-warning for toxicity presented in water environment attracts increasing attentions as it saves time to retain water safety and human health. Electrochemically active biofilm (EAB) sensor is a promising device for in situ real-time water toxicity early-warning. To improve the sensitivity of EAB sensor particularly for low-concentration toxicity warning, this study employed titanium mesh (TiM) as the anode to construct an EAB sensor. Compared to traditional EAB sensor with carbon felt (CF) anode, the sensitivity of the TiM sensor was increased up to 37.4 times. The effects of mesh size (TiM50, TiM100, TiM150) and operation mode (flow-by and flow-through) on the sensitivity of TiM sensors were further investigated. Results showed the sensor with TiM100 anode had the highest inhibition rate (IR) in flow-by mode, attributed to low charge transfer resistance (R ct) and fast mass transfer. Flow-through operation could further enhance TiM100 sensor's sensitivity from flow-by operation and succeeded to signal as low as 0.0025% formaldehyde, the lowest so far tested in EAB sensor with sensing anode. Multiple toxicity shocks on flow-through TiM100 sensor revealed its good recoverability towards all tested formaldehyde concentration from 0.01% to 0.0025%, during which electrochemical activity degradation and biomass accumulation partially impaired the repeatability. This work highlights the great improvement of EAB sensors by utilizing titanium mesh as EAB carrier and provides a reference for the practical application of metallic materials for EAB sensors. [ABSTRACT FROM AUTHOR]

Researchers believe that adding conductive mediums in electrochemically active biofilms (EABs) would improve the sensitivity of EAB-based biosensor for real-time water quality early-warning through facilitating the extracellular electron transfer (EET), which has been hardly evidenced mostly because naturally formed EABs employed in previous biosensor studies were recognized distinct and incapable of delivering comparable electrical signals. By preparing artificial EABs where Shewanella oneidensis MR-1 was encapsulated in sodium alginate (SA), this study solved how polypyrrole (PPy) as conductive medium would affect the sensitivity of EAB-based biosensor, as well as mass transfer of toxicant during this process. Different mass ratios (0.125:1, 0.25:1 and 1:1) of PPy over SA were tested, and the sensitivity promoted by 20%, 15% and 6%, respectively. Results indicated that a small amount of PPy addition (PPy: SA = 0.125: 1 in mass ratio) was more effective to increase the biosensor's sensitivity compared to larger amount of PPy employed in EAB. This was when improved conductivity introduced by PPy would dominate in affecting the sensitivity over contrarily weakened mass transfer in the meantime. • Artificial electroactive biofilms containing polypyrrole were prepared. • Polypyrrole increases conductivity as well as decreases mass transfer. • Small amount of polypyrrole better increased biosensor's sensitivity. [ABSTRACT FROM AUTHOR]

Revealing the pathways of electron transport within electrochemically active biofilms (EABs) is of great importance. Here, mixed-culture EABs are grown on three interdigitated microelectrode arrays (IDAs) with different gap widths of 10 μm, 20 μm and 50 μm and their conductances are determined. The maximum conductive current increases with the decrease of the gap width and charge transfer resistance obtained for the biofilm attaching on the electrode is 3–11 fold less than that for biofilm bridging gaps, suggesting high conductance of biofilm closer to the electrode surface. Results from Raman analysis show high abundance of multi-heme cytochromes in biofilm bridging 10 μm gap, leading to small resistance of biofilm growing on the IDA with 10 μm gap. In addition, the maximum conductive current of biofilm bridging gaps at the potential of −0.40 V vs. Ag/AgCl suggests that electron transfer in biofilm growing on IDAs is redox driven. All these results indicate the spatial heterogeneity of electron transport processes acting within biofilm. Biofilm conductance decreased with the increase of gap's width. Small resistance was found for biofilm adjacent to the electrode surface. Biofilm conductance was depended the abundance of multi-heme cytochrome. The process of electron transfer with EABs was spatial heterogeneous. Panpan Liu: Conducting a research and investigation process, writing the initial draft [ABSTRACT FROM AUTHOR]