Search

Toxicity monitoring is essential for the protection of public health and ecological safety. Microbial fuel cell (MFC) sensors demonstrated good potential in toxicity monitoring, but current MFC sensors can only be used for anaerobic water monitoring. In this study, a novel gas diffusion (GD)-biocathode sensing element was fabricated using a simple method. The GD-biocathode MFC sensor can directly be used for formaldehyde detection (from 0.0005% to 0.005%) in both aerobic and anaerobic water bodies. Electrochemical analysis indicated that the response by the sensor was caused by the toxic inhibition to the microbial activity for the oxygen reduction reaction (ORR). This study for the first time demonstrated that the GD-biocathode MFC sensor has a detection limit of 20 ppm for formaldehyde and can be used to monitor air pollution. Selective sensitivity to formaldehyde was not achieved as the result of using a mixed-culture, which confirms that it can serve as a generic biosensor for monitoring gaseous pollutants. This study expands the realm of knowledge for MFC sensor applications. [ABSTRACT FROM AUTHOR]

The development of real-time online warning system for toxicity materials is important to ensure the safety of water supply. This study for the first time constructs luminescent bacteria (Vibrio fischeri) biofilm to deliver both electrical and optical real-time response for Cu(II) toxic shock in a bioelectrochemical system (BES) sensor. Compared to biocathode, bioanode was more suitable as sensitive elements. With three tested concentrations of Cu(II), i.e., 1 mg/L, 3 mg/L and 6 mg/L, electrical signals were raised. But optical signal failed to respond to the lowest concentration, suggesting that electrical signal then was produced by chemical reaction of Cu(II) on the electrode surface. For 3 mg/L and 6 mg/L Cu(II) shock, more rapid optical signals were observed than electrical signal, indicating that both the biofilm's surface and inner was affected. In addition, high concentration of Cu(II) toxic as 6 mg/L caused irreversible damage in the biosensor as there were great fluctuation in the recovery curve and large recovery ratio up to -10.39% for optical signal. These results provided a comparison between optical and electrical signals simultaneously produced by a biosensor and visual evidences for better understanding of the toxicity process in the biosensor. Image 1 • Luminescent bacteria biofilm was constructed as a sensing element. • Simultaneously production of photons and electrons by Vibrio fischeri biofilm. • Compatible Vibrio fischeri biofilm as bioanode rather than biocathode with biosensor. • Both optical and electrical signals respond to Cu2+ shock. [ABSTRACT FROM AUTHOR]

Researchers believe that adding conductive mediums in electrochemically active biofilms (EABs) would improve the sensitivity of EAB-based biosensor for real-time water quality early-warning through facilitating the extracellular electron transfer (EET), which has been hardly evidenced mostly because naturally formed EABs employed in previous biosensor studies were recognized distinct and incapable of delivering comparable electrical signals. By preparing artificial EABs where Shewanella oneidensis MR-1 was encapsulated in sodium alginate (SA), this study solved how polypyrrole (PPy) as conductive medium would affect the sensitivity of EAB-based biosensor, as well as mass transfer of toxicant during this process. Different mass ratios (0.125:1, 0.25:1 and 1:1) of PPy over SA were tested, and the sensitivity promoted by 20%, 15% and 6%, respectively. Results indicated that a small amount of PPy addition (PPy: SA = 0.125: 1 in mass ratio) was more effective to increase the biosensor's sensitivity compared to larger amount of PPy employed in EAB. This was when improved conductivity introduced by PPy would dominate in affecting the sensitivity over contrarily weakened mass transfer in the meantime. • Artificial electroactive biofilms containing polypyrrole were prepared. • Polypyrrole increases conductivity as well as decreases mass transfer. • Small amount of polypyrrole better increased biosensor's sensitivity. [ABSTRACT FROM AUTHOR]

Besides serving in wastewater treatment and energy generation fields, electroactive biofilm (EAB) has been employed as a sensitive bio-elements in a biosensor to monitor water quality by delivering electrical signals without additional mediators. Increasing studies have applied EAB-based biosensor in specific pollutant detection, typically biochemical oxygen demand (BOD) detection, as well as in early-warning of composite pollutants. Based on a comprehensive review of literatures, this study reveals how EAB outputs electrical signal, how we can evaluate and improve this performance, and what information we can expect from EAB-based biosensor. Since BOD detection and early-warning are normally confusing, this study manages to differentiate these two applications through distinguished purposes and metrics. Based on the introductions of progresses and applications of EAB-based biosensors so far, several novel strategies toward the future development of EAB-based biosensors are proposed. • Electroactive biofilm (EAB) can serve as sensitive element in biosensor. • Applications of EAB-based biosensor contain BOD detection and early-warning. • Accuracy of BOD detection is improved by eliminating interferences. • Sensitive and accurate early-warning is of great concern. • Better reproducibility of EAB-based biosensor contributes to standardization. [ABSTRACT FROM AUTHOR]

• Summary of cutting-edge researches on microbial electrochemical sensor. • Discussion versatility and limitations of the traditional bioanode sensing element. • Highlight to explore spatial structure and interfacial electrochemical characteristics. • Suggestions for improving the bioavailability of toxic agents. • Potential challenges in field test for water biotoxicity monitoring. The development of low cost, convenient, and efficient biosensors is critical for water biotoxicity monitoring. Microbial electrochemical sensors employ electrode-biofilm as the sensing element, and detect biotoxicity by tracking the electron transfer between electroactive microorganisms and electrodes under toxic stress. Use of such biosensors in the aquatic environment can provide an early warning for the presence of various toxicants. In this paper, cutting-edge studies on strategies to create high performance microbial electrochemical biosensors are reviewed, which have mainly focused on different sensing elements. Bioanode sensing element-based microbial electrochemical sensors have been successfully applied in the laboratory to detect various toxicants, and to diagnose typical anaerobic wastewater treatment processes. The abiotic cathode sensing element is also included, which is mainly based on the electrochemical reduction of target analytes or its inhibition of the oxygen reduction reaction (ORR). The biocathode sensing element successfully solves the problems of low sensitivity and high false-negative rate, and recent advances and future perspectives in this field are highlighted. The limitations and potential solutions associated with the practical application of microbial electrochemical sensors for water biotoxicity monitoring are discussed. [ABSTRACT FROM AUTHOR]