Search

Organic light-emitting electrochemical cells (LEC) are promising for lighting applications but in many cases these devices suffer from unbalanced electrochemical doping, which cause instability and degradation of the cells. A predominant p-doping over n-doping causes an off-centered emissive p–n junction, which leads to poor power-conversion efficiency. Here, we report a half-gate LEC transistor (HG-LECT), in which an ion-conductive gate made from poly(3,4-ethylenedioxythiophene)-poly-(styrenesulfonate) is employed to combat this instability problem. The gate material, covering half of the channel, is used to enhance the n-doping process in this part by employing an appropriate operation protocol. We demonstrate a centered light emission zone, closely following the geometry of the gate configuration. The HG-LECT with centered emission profile is shown to be more efficient than the corresponding LEC without the gate electrode, and its n-doping level is measured to be 15%. [ABSTRACT FROM AUTHOR]

Abstract The conductive polymer poly(3,4-ethylenedioxythiphene):poly(styrenesulfonate) (PEDOT:PSS) is widely used in organic electronics and printed electronics due to its excellent electronic and ionic conductivity. PEDOT:PSS films exhibit anisotropic conductivities originating from the interplay of film deposition processes and chemical structure. The previous studies found that high boiling point solvent treated PEDOT:PSS exhibits an anisotropy of 3–4 orders magnitude. Even though both the in-plane and out-of-plane conductivities are important for the device performance, the out-of-plane conductivity is rarely studied due to the complexity with the experiment procedure. Cellulose-based paper or films can also exhibit anisotropic behavior due to the combination of their intrinsic fibric structure and film formation process. We have previously developed a conductive paper based on PEDOT:PSS and cellulose which could be used as the electrodes in energy storage devices. In this work we developed a novel measurement set-up for studying the anisotropy of the charge transport in such composite materials. A tool with two parallel plates mounted with spring loaded probes was constructed enabling probing both lateral and vertical directions and resistances from in-plane and out-of-plane directions to be obtained. The measurement results were then input and analyzed with a model based on a transformation method developed by Montgomery, and thus the in-plane and out-of-plane conductivities could be detangled and derived. We also investigated how the conductivity anisotropy depends on the microstructure of the cellulose template onto which the conductive polymer self-organizes. We show that there is a relatively small difference between the in-plane and out-of-plane conductivities which is attributed to the unique 3D-structure of the composites. This new knowledge gives a better understanding of the possibilities and limitations for using the material in electronic and electrochemical devices. Graphical abstract Image 1 Highlights • Developed a simple to use generic tool for measuring 3-D resistances of thick conducting self-standing films. • The in-plane and out-of-plane conductivities were deduced by a method developed by Montgomery. • Both CNF-PEDOT:PSS and pulp-PEDOT:PSS films exhibit anisotropic conductivity. • CNF-PEDOT:PSS films show thickness independent anisotropic conductivity. • Pulp-PEDOT:PSS became less anisotropic with increasing thicknesses. [ABSTRACT FROM AUTHOR]

Advances in organic electronics necessitates, ultrathin and miniaturized implantable energy storage modules. Here, an approach for the fabrication of on-chip, ultraflexible electrochemical capacitors is demonstrated. Two different electroactive conjugated polymers are utilized in a fabrication route that allows the patterning of finger electrodes for an ultraflexible energy storage technology. A strategy is demonstrated to realize supercapacitors with a total device thickness of 4 μm, including substrate, polymer electrode, and electrolyte. Interdigitated 20-finger electrodes from either Poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) or polythiophene functionalized with tetraethylene glycol side chains P(g42T-T), with 50 μm or 90 μm electrode spacings, are fabricated using a parylene peel off method, followed by electrolyte deposition. The miniaturized devices show 0.77 mF/cm2 areal capacitance for PEDOT:PSS and 0.06 mF/cm2 for P(g42T-T). Furthermore, the devices exhibit excellent mechanical durability, showing robust operational performance at a bending radius of 6.5 mm. [Display omitted] • Scalable fabrication route for polymer IDE structures using parylene peel off method. • PEDOT:PSS and P(g42T-T) microsupercapacitors with more than 0.6 mF/cm2 capacitance. • Ultrathin organic electronics device technology with total thickness of 4 μm. • Excellent mechanical durability, showing robust operational performance at a bending radius of 6.5 mm. [ABSTRACT FROM AUTHOR]

Ion selective membranes are at the heart of energy conversion and harvesting, water treatment, and biotechnologies. The currently available membranes are mostly based on expensive and non-biodegradable polymers. Here, we report a cation-selective and low-cost membrane prepared from renewable nanocellulose and 1,2,3,4-butanetetracarboxylic acid which simultaneously serves as crosslinker and source of anionic surface groups. Charge density and structure of the membranes are studied. By using different degrees of crosslinking, simultaneous control over both the nanochannel structure and surface charge concentration is achieved, which in turn determines the resulting ion transport properties. Increasing negative charge concentration via higher crosslinker content, the obtained ion conductivity reaches up to 8 mS/cm (0.1 M KCl). Optimal ion selectivity, also influenced by the solution pH, is achieved at 20 wt% crosslinker addition (with ion conductivity of 1.6 mS/cm). As regular ~1.4 nm nanochannels were formed at this composition, nanofluidic contribution to ion transport is likely. • A renewable, low cost crosslinked nanocellulose membrane was reported. • The crosslinked membranes show excellent ion conductivity and selectivity. • A higher amount of crosslinker results in a greater ion conductivity. • An optimal ionic selectivity obtained at an addition of the crosslinker of 20 wt%. • This nanocellulose membrane is promising for ionic devices and upscaled applications. [ABSTRACT FROM AUTHOR]