Search

Under coupled bending-shear-torsion (B-S-T) loading combinations, the ultimate bearing capacity of concrete filled steel tube (CFST) short columns has not been studied. In this paper, the test on eight CFST short columns was carried out. The load-deformation relations and failure modes of CFST short columns were obtained and analyzed. Based on experimental results, the failure mechanism of CFST short columns were obviously affected by the ratio of bending moment to torque, and CFST short columns under coupled B-S-T loading combinations had good ductility. The ultimate bending-shear bearing capacity of CFST short columns was significantly decreased by increasing torsion moment. Moreover, nonlinear finite element analysis was performed, which generated an accurate prediction of the ultimate capacity of concrete filled steel tube short columns under coupled B-S-T. As a conclusion, a simplified design equation for calculating the coupled B-S-T bearing capacity of CFST short columns was proposed according the regression results of the finite element parametric analysis. [ABSTRACT FROM AUTHOR]

Under gravity and the horizontal earthquake load, the eccentric compression and torsion combined action will be produced in the piers of curved girder bridges and the main arch of arch bridge. In order to study the torsion behavior of concrete filled steel tube columns subjected to eccentric compression, tests were carried out on eight specimens of concrete filled steel tube column subjected to static pure torsion, cyclic pure torsion and eccentric compression-torsion cyclic load. The results of tests have indicated that, the hysteresis curve of concrete filled steel tube column subjected to torsion cyclic load was plump; no pinch phenomenon can be found; the damage and degradation degree of the strength and stiffness of specimens is lower; and high energy dissipation capacity can be achieved. The stiffness degradation of the specimens with square section subjected to eccentric compression-torsion cyclic load is more obvious. The eccentric compression has led to weaken of the energy dissipation capacity of the square section concrete filled steel tube column. Under the ultimate state, the wave angle of steel tube was affected by the eccentric compression. [ABSTRACT FROM AUTHOR]

Recent developments in the high-output wind turbine have heightened the need for CFDST support towers. Tapered Concrete-Filled Double Skin Steel Tubular columns with Large Hollow Ratios (TLHR-CFDSTs) are the typical members in the wind turbine towers, which are usually subjected to torsion during the life cycle. It is necessary to pay more attention to these members under torsion due to their tapered shapes and thin-walled cross sections. This paper thus presents an experimental study on the torsional behaviour of the TLHR-CFDST column. Specimens with different tapered angles, hollow ratios, tubes' thicknesses and axial compression ratios were tested under pure torsion and compression–torsion. The typical failure modes, torque versus deformation relations, strain distributions and the influence of important parameters are revealed. Based on the experimental results, the mechanism of TLHR-CFDST columns under torsion is discussed. The applicability of existing torsional capacity calculation methods is evaluated and finally a simplified method for predicting the torsional capacity of TLHR-CFDST columns is proposed. • Tests on TLHR-CFDST columns under pure torsion and compression–torsion​ are reported. • Behaviour and parametric effects of TLHR-CFDST columns under torsion are revealed. • Torsional mechanism of TLHR-CFDST columns is discussed. • Theoretical method for predicting the torsional capacity of TLHR-CFDST columns is proposed. [ABSTRACT FROM AUTHOR]

This paper presents a pseudo-static test investigation and finite element analysis on the behavior of circular concrete-filled double skin steel tube (CFDST) members under axial compression and torsion. The hollow ratio (χ) and axial compression ratio (n) are considered in the test study. The ductility, hysteretic behavior, failure modes, and compression–torsion correlation of circular CFDST members are discussed. The comparison results show that the validated finite element model is capable to capture the behavior of circular CFDST members under compression and torsion. The effect of loading paths and various parameters on the compression–torsion correlation of circular CFDST members are analyzed. Parametric analyses are carried out to investigate the effect of key parameters, such as material properties, nominal steel ratio, the wall thickness of inner steel tube, and hollow ratio on the compression–torsion correlation of circular CFDST members. It can be seen that the circular CFDST members under compression and torsion possess good load-bearing capacity, energy dissipation, and ductility properties. The loading paths, yield strength of inner and outer steel tubes, nominal steel ratio, and the wall thickness of inner steel tubes have little effect on the compression–torsion correlation of the composite members. When the axial compression ratio is less than 0.2, the axial compression load can slightly improve the torque capacity of circular CFDST members. Finally, the compression–torsion correlation equation of these members was proposed by regression analysis, and design formulas with good accuracy for predicting the torque capacity of circular CFDST members under compression and torsion were proposed. • Test investigation and numerical analysis were conducted to study behavior of CFDST members under compression and torsion. • Parametric analyses and regression analysis were conducted to propose the Axial compression and torsion correlation equation of CFDST members. • Parametric analyses have been conducted considering key parameters. • The axial compression and torsion correlation equation of CFDST members were proposed via regression analysis. • Formulas with good accuracy for predicting the torque capacity of CFDST members under compression and torsion were proposed. [ABSTRACT FROM AUTHOR]