Search

In the process of long-term water flooding in the Gaoqian Southern Area with an average porosity of 30% and an average permeability of 1333.5 × 10 − 3 μm2, the fluid-solid interaction among oil, water, and rock has a great influence on the pore structure. It has resulted in changes in reservoir parameters with the extension of time. This paper used electron microscopy scanning, mercury injection, X-ray diffraction, physical properties, and oil-water relative permeability curves to study the variation of clay mineral content, pore throat structure, porosity, permeability, and relative permeability curves of high-permeability sandstone after high-pressure water flooding. The results showed that clay minerals such as montmorillonite and kaolinite were dissolved, hydrated, and migrated after long-term water flooding, which resulted in the decrease of clay mineral content in fine sandstone and medium sandstone, the increase of pore throat radius, and the decrease of displacement pressure, median pressure, and separation coefficient. The saturation of the isotonic point of the oil-water relative permeability curve was obviously shifted to the right, the hydrophilicity was significantly enhanced, and the porosity and permeability were effectively improved, but there was a blockage of the throat less than 2 μm in the fine sandstone. In addition, this paper established the equations of water injection, permeability, irreducible water saturation, residual oil saturation, and oil-water relative permeability curve coefficient and establishes the initial permeability model with the well data before water flooding. The logging interpretation results of development wells in the process of water flooding as verification data were used, and the relative error of permeability far lower than the general requirement of permeability error within an order of magnitude was less than 30%, which verified the rationality of the method. [ABSTRACT FROM AUTHOR]

The axial deployment force is an indispensable parameter of a lanyard-deployed coilable mast, which reflects its load capacity in practical applications. However, research on the axial deployment force in the literature is very limited, and there are no mature numerical methods to determine this parameter in the design stage of coilable masts. In this paper, a numerical method for determining the axial deployment force of a lanyard-deployed coilable mast in the local coil mode is presented. Through this method, the designer can quickly obtain the estimated value of the axial deployment force in the design stage, which is convenient for the quantitative design of parameters. To verify the correctness of the proposed method, a dynamic simulation of the coilable mast is carried out, and a microgravity test is performed. The comparison results show that the error between the numerical method and the simulation and experimental results is less than 5%, which proves the correctness of the proposed method. In addition, the coilable mast studied in this paper has been verified by an actual microsatellite deployment in orbit. [ABSTRACT FROM AUTHOR]

This paper examines the dynamic behavior of a particular category of discrete predator-prey system that feature both fear effect and refuge, using both analytical and numerical methods. The critical coefficients and properties of bifurcating periodic solutions for Flip and Hopf bifurcations are computed using the center manifold theorem and bifurcation theory. Additionally, numerical simulations are employed to illustrate the bifurcation phenomenon and chaos characteristics. The results demonstrate that period-doubling and Hopf bifurcations are two typical routes to generate chaos, as evidenced by the calculation of the maximum Lyapunov exponents near the critical bifurcation points. Finally, a feedback control method is suggested, utilizing feedback of system states and perturbation of feedback parameters, to efficiently manage the bifurcations and chaotic attractors of the discrete predator-prey model. [ABSTRACT FROM AUTHOR]

In this paper, the limit cycles and local bifurcation of critical periods for a class of switching Z 2 equivariant quartic system with two symmetric singularities are investigated. First, through the computation of Lyapunov constants, the conditions of the two singularities to become the centers are determined. Then, we prove that there are at most 18 limit cycles with a distribution pattern of 9-9 around the two symmetric singular points of the system. Numerical simulation is conducted to validate the obtained results. Furthermore, by calculating the period constants, we determine the conditions for the critical point to be a weak center of finite order. Finally, the number of local critical periods that bifurcate from the equilibrium point under the center conditions is discussed. This study presents the first example of a quartic switching smooth system with 18 limit cycles and 4 local critical periods bifurcating from two symmetric singular points. [ABSTRACT FROM AUTHOR]

Multiple hypersonic gliding vehicles' (HGVs') formation control problems with obstacle and collision avoidance are investigated in this paper, which is addressed in the stage of entry gliding. The originality of this paper stems from the formation control algorithm where constraints of dynamic pressure, heating rate, total aerodynamic load, control inputs, collision avoidance, obstacle avoidance, and the terminal states are considered simultaneously. The algorithm implements a control framework designed to be of two terms: distributed virtual controller and actual control input solver. The distributed virtual controller is based on distributed model predictive control with synchronous update strategy, where the virtual control signals are derived by the optimization simultaneously at each time step for each HGV under directed communication topology. Subsequently, according to the virtual control signals obtained, a coupled nonlinear equation set is solved to get actual control signals: each HGV's bank angle together with the angle of attack. The actual control input solver adopts a feasible solution process to calculate the actual control signals while dealing with constraints. Finally, extensive numerical simulations are implemented to unveil the proposed algorithm's performance and superiority. [ABSTRACT FROM AUTHOR]

In this paper, finite element simulation of asymmetric rolling in relief rolls of C11000 copper alloy in order to analyze the effectiveness of possible roll profiles and technological schemes of deformation was performed. The scientific innovation of this work lies in determining the patterns of development of stress-strain state parameters for various configurations of rolls, as well as determining the effectiveness of metal processing using various technological schemes. It was found that the use of trapezoidal relief makes it possible to increase the level of metal processing by almost 5 times compared with the use of radial relief. Comparison of technological schemes of deformation showed that deformation with 180° workpiece turning between passes significantly reduces the influence of the asymmetry factor. Deformation without changing the workpiece position between the passes has the opposite effect, and such a scheme significantly increases the influence of the asymmetry factor. Deformation with a transverse workpiece shift for the relief period between passes has the effect of a "golden mean." The conducted laboratory experiment for lead billet showed that the shape change of lead billet during computer simulation has a high level of convergence with real conditions. At each stage of deformation, the difference in the geometric parameters of the workpiece between the model and the experiment did not exceed 3-5%. When deforming a copper billet, the maximum difference level was 8%, which is the result of the low rigidity of the rolling cage with smooth rolls. [ABSTRACT FROM AUTHOR]

Background. The deterministic fiber tracking method has the advantage of high computational efficiency and good repeatability, making it suitable for the noninvasive estimation of brain structural connectivity in clinical fields. To address the issue of the current classical deterministic method tending to deviate in the tracking direction in the region of crossing fiber region, in this paper, we propose an adaptive correction-based deterministic white matter fiber tracking method, named FTACTD. Methods. The proposed FTACTD method can accurately track white matter fibers by adaptively adjusting the deflection direction strategy based on the tensor matrix and the input fiber direction of adjacent voxels. The degree of correction direction changes adaptively according to the shape of the diffusion tensor, mimicking the actual tracking deflection angle and direction. Furthermore, both forward and reverse tracking techniques are employed to track the entire fiber. The effectiveness of the proposed method is validated and quantified using both simulated and real brain datasets. Various indicators such as invalid bundles (IB), valid bundles (VB), invalid connections (IC), no connections (NC), and valid connections (VC) are utilized to assess the performance of the proposed method on simulated data and real diffusion-weighted imaging (DWI) data. Results. The experimental results of the simulated data show that the FTACTD method tracks outperform existing methods, achieving the highest number of VB with a total of 13 bundles. Additionally, it identifies the least number of incorrect fiber bundles, with only 32 bundles identified as wrong. Compared to the FACT method, the FTACTD method reduces the number of NC by 36.38%. In terms of VC, the FTACTD method surpasses even the best performing SD_Stream method among deterministic methods by 1.64%. Extensive in vivo experiments demonstrate the superiority of the proposed method in terms of tracking more accurate and complete fiber paths, resulting in improved continuity. Conclusion. The FTACTD method proposed in this study indicates superior tracking results and provides a methodological basis for the investigating, diagnosis, and treatment of brain disorders associated with white matter fiber deficits and abnormalities. [ABSTRACT FROM AUTHOR]

This paper aims to study the law of pressure behavior and the characteristics of mutual influence in the process of steeply inclined coal seam mining. Based on the geological and engineering conditions of the B8 coal seam in Nanshan coal mine, this paper explores the law of mine pressure behavior in the process of steeply inclined coal seam mining by means of theoretical analysis and FLAC3D numerical simulation. Based on this, this paper also examines the influence of the interaction range between coal seams, the reasonable setting size of the section coal pillar, and the mining distance of the working face on the return air roadway. The results suggest as follows: (1) With an increase in the coal seam dip angle, the difference in the abutment pressure plastic zone between upper and lower coal pillars increases, and when mining in steeply inclined coal seams, the stress concentration in the lower and upper part of the working face deviates to the roof and floor respectively, which is obviously different from that of gently inclined coal seams. (2) The vertical stress above the section coal pillar changes in three stages with an increase in the width of the coal pillar, and the width of the coal pillar in the second stage can be taken as the reasonable size of the width of the coal pillar. The numerical simulation results are consistent with the theoretical calculation results, which indicate the high reliability of this method in determining the reasonable coal pillar size. (3) With an increase in the mining distance in steeply inclined coal seams, the maximum pressure around the working face and above the return air roadway has gone through three stages. When the distance between the working face and the adjacent return air roadway is close, the pressure above the return air roadway increases sharply, and disturbance is stronger. [ABSTRACT FROM AUTHOR]

Space close-range inspection can be used to carry out close-range observation and monitoring of targets for identifying the target's types and working states, which is of great significance for space missions such as in-orbit services. The effectiveness evaluation of space inspection tasks will significantly affect the studies on the trajectory design, orbit motion control, and task termination conditions. However, the evaluation models in previous studies are too simple such as that they are usually without considering dynamic changes in the satellite orbit relative motion. Besides, these studies fail to build a comprehensive evaluation model for the whole inspection task process. In this paper, taking the most commonly used optical inspection as an example, the novel multifactor inspection task effectiveness evaluation models were investigated, including the constraint models of observation, the relative distance evaluation model, the effective observation time evaluation model, and the target observation angle evaluation model. These models solve the effectiveness evaluation problem for the complete process of an inspection task, which can support the design of inspection strategies and trajectories better by using the evaluation results. In addition, numerical simulations and 20 semiphysical experiments were carried out to validate the proposed evaluation models. [ABSTRACT FROM AUTHOR]

As one of the main hydrogen production devices, the performance of the proton exchange membrane electrolytic cell (PEMEC) is directly related to the geometric design of the flow channel. In this paper, a new orthogonally sinusoidal channel with periodic fluctuations in both horizontal and vertical planes is proposed. The effects of amplitude and angular frequency in two orthogonally sinusoidal channels with the same or opposite frequency on PEMEC performance are studied by numerical simulation. The results show that the spatial amplitude and angular frequency effectively improve the electrochemical performance and mass transfer performance of PEMEC. Compared with Case 1-1, the polarization performance of Case 7-2 is increased by 16.39% because of the largest spatial amplitude. The oxygen content at 40 mm away from the inlet in the diffusion layer is also decreased by 42.63%. The horizontal angular frequency can increase the hydrogen content by 11.07% at most in Case 5-2. However, the increase in vertical angle frequency will inhibit the oxygen removal on the anode side. The sinusoidal flow channel in orthogonal spaces will provide a particular reference for the design of PEMEC in the future. [ABSTRACT FROM AUTHOR]

This paper studies the distribution characteristics of acoustic emission (AE) events in supporting roadways under different dynamic load conditions through numerical simulation and theoretical analysis. According to the principle of AE numerical simulation, the roadway model is established by FLAC3D software, and the supporting structure of the bolt cable is established by editing the Fish function. According to the model dynamic load application criterion, the relationship between the peak velocity of the particle, the distance from the source center to the dynamic impact damage point, and the dynamic load intensity is introduced. The velocity-distance-energy relationship is deduced from the relationship to determine the magnitude of the dynamic load energy. The simulation results show that the intensity of the dynamic load source and the distance of the dynamic load source directly impact the AE events. The larger the dynamic load intensity and the closer to the dynamic load source, the more concentrated the AE events. The roadway has a blocking effect on the transmission of the dynamic load stress waves. According to this characteristic, the roadway can be protected by a high-pressure relief roadway. Rock lithology greatly influences the transmission of dynamic load stress waves and the number of AE events. When the dynamic load stress wave passes through the rock strata of different lithologies, the attenuation of the dynamic load energy and the number of AE events are large. However, when the dynamic load stress wave passes through the rock strata of the same lithology, the attenuation of the dynamic load energy and AE events is small. The surrounding rock structure in the bottom corner area of the roadway is susceptible to disturbance from dynamic load sources above the roadway. The results are greatly significant for studying the AE characteristics of support roadways with disturbance-typeimpact failure. [ABSTRACT FROM AUTHOR]

This paper presents synchronization of mixed continuous-discrete complex network via impulse-quantizing approach. A delay-partitioning group strategy is proposed and impulse-quantizing control is designed to derive theoretical criteria ensuring scale-type synchronization of complex networks. Our results show that synchronization of mixed continuous-discrete complex networks can be realized by controlling delay-partitioning subgroup nodes with impulsive quantization. The theoretical results give scale-limited sufficient conditions for quantized synchronization relying on control gains, impulsive intervals, and delays. A numerical simulation is given to demonstrate the effectiveness of the theoretical results. [ABSTRACT FROM AUTHOR]

The large-scale space structure during on-orbit assembly is a time-varying system. The dynamic modeling problem of such incrementally increasing space structure is investigated, and a modular dynamic modeling approach is proposed in this paper. The dynamic model of each substructure is first established, and then, a database is designed to store substructure models, which is used for subsequent dynamic modeling in the assembly process. The fixed connection relationship between adjacent substructures is described by constraint conditions, which lead to the coefficient matrices of adjacent substructures being decoupled. The substructures are assembled in a given sequence, and then, the dynamic modeling, to describe the large-scale space structure on-orbit assembly, is gradually completed via using the proposed modeling approach. The numerical simulation is finally presented. The results demonstrate that the extra calculation resulting from the coefficient matrices coupling of adjacent substructures is avoided. Moreover, the proposed dynamic model can accurately describe the dynamic characteristics of the large-scale space structure during on-orbit assembly. [ABSTRACT FROM AUTHOR]

Offshore wind turbines (OWTs) are considered vital to the promotion of the development of renewable energy. Especially, floating OWTs can be deployed over a larger area than bottom-fixed OWTs. The floating OWTs, however, are vulnerable to vibration induced by disturbances and require a backup power supply in the case of power outage. On the one hand, various kinds of inerter-based devices have been proposed especially for vibration suppression of civil structures subjected to earthquake loadings. Recently, combined with electromagnetic devices, the inerter technologies have also been applied in the field of vibration energy harvesting such as point absorber wave energy converters. Thus, this paper proposes a novel floating OWT consisting of two bodies combined with inerter-based power take-off (PTO) devices which accomplishes vibration suppression and wave energy conversion at the same time. To investigate the vibration suppression and energy conversion capabilities of the proposed floating OWT with a variety of inerter-based PTO devices for ocean waves, numerical simulation studies employing WEC-Sim are conducted, and the performance of each system is compared for regular and irregular waves. Results show that the proposed floating OWT with the appropriately designed inerter-based PTO devices for the incident wave period has great potential for both vibration suppression and wave energy conversion in a specific frequency range. [ABSTRACT FROM AUTHOR]

In order to study the influence of bedding structure on the mechanical properties of rock mass structure, this paper takes the layered carbonaceous slate in the Muzhailing tunnel as the research object, and studies the mechanical properties of layered slate under uniaxial compression and Brazilian splitting. In the numerical simulation, the discrete element software MUSEN (bonded particle model, BPM) is used to simulate the failure behavior of layered rock mass in the process of quasi-static compression. The main research contents of this paper are as follows: (1) the relationship between the microscopic Young's modulus and the macroscopic Young's modulus. (2) Influence of tangential shear strength and normal tensile strength on particle model. (3) The influence of different particle distributions on the simulation results. (4) The particle model with different bedding inclinations was simulated numerically. Through the comparative analysis of simulation and experiment, the results show that the mechanical response and failure mode have good consistency, and the splitting evolution process of layered slate with different bedding inclination angles is reproduced. [ABSTRACT FROM AUTHOR]

In recent years, due to the increase in the incidence of traffic accidents, the number of people with limb injuries has also increased. At the same time, among the aging population, neurological diseases or cardiovascular and cerebrovascular diseases have caused many people to have limb hemiplegia. It has been clinically proven that the use of rehabilitation equipment can help patients with limb injuries to restore limb motor function. This paper takes wearable lower limb rehabilitation exoskeleton as the research object, and its main contents are mechanical structure design, kinematics analysis, gait planning, virtual prototype simulation, and experimental verification and analysis. Based on the physiological characteristics of human body and the principle of comfortable and reliable wearing, this paper designs wearable exoskeleton for lower limb rehabilitation. Firstly, the physiological structure characteristics and movement mechanism of human lower limbs were studied and analyzed. By referring to the rotation range and height and size of each joint of human lower limbs, the overall scheme of wearable lower limb rehabilitation exoskeleton was designed and the degree of freedom was allocated. At the same time, Solidworks was used to establish a three-dimensional model. On the basis of a 3D model, a kinematics model was established, and the forward kinematics solution was obtained by using homogeneous coordinate transformation. Since the inverse kinematics solution was relatively complicated, the inverse kinematics solution was conducted in this paper according to the geometric relations of the joints of the lower limbs. Kinematics analysis of the exoskeleton structure of wearable lower limb rehabilitation was carried out to lay a theoretical foundation for gait planning. The off-line gait planning was carried out by using the method based on ZMP stability criterion, and the gait planning was divided into five stages: squat, start, middle step, stop and rise, and the motion trajectory of the center of mass and ankle joint was planned. Based on the inverse kinematics formula, the function of the change of joint angle with time in walking process is derived. The virtual prototype is established in ADAMS, and the simulation of virtual prototype is carried out by using the function of gait planning's joint angle and time. The correctness of structural design and gait planning was verified by measuring the trajectories of the centroid and ankle joints in each gait stage and the functional relationship between the rotation angle of each joint and time. Then, using a 3D dynamic capture system to capture the human lower limb motion trajectory of each joint, each joint trajectory data output, using the MATLAB software to output data, gets the joint trajectory change over time function curve and is used to verify feasibility and applicability of human gait planning. Through the research and analysis of the joints of the lower limbs of the human body, it can be concluded that the hip joint and the knee joint have 3 degrees of freedom, respectively, and the knee joint has 1 degree of freedom. [ABSTRACT FROM AUTHOR]

This paper focuses on simulating the collision breakage process between the agglomerate and hammer in a hammer crusher by the discrete element method (DEM) as the interaction between particles. This enables us to consider the energy change in the collision breakage process of the hammer. The agglomerate model is built by using the EDEM 2.7 software according to the principle of closest packing in crystallography, while the hammer model is modeled into an assembly of different sizes of spherical particles to make the collision breakage process between the agglomerate and hammer as the one of interrelation of particles. With these models, we mainly investigated collision force, collision impulse, energy breaking agglomerate, and the relationship between the specific breakage energy and agglomerate damage ratio. The collision force is represented as Gaussian function, the collision impulse is represented by the function of the mass ratio of agglomerate to hammer and the product of agglomerate mass and collision velocity, and the relationship between the specific breakage energy and agglomerate damage ratio is represented by exponential function. Finally, it can be seen from this study that, when crushing the agglomerate by hammer impact, it is necessary to increase the specific breakage energy by 1.75 times in order to increase the agglomerate damage ratio from 85% to 90% but 2.13 times in order to increase 95%. The proposed method can be used for the further development and design of the various types of crusher. [ABSTRACT FROM AUTHOR]

Focusing on the phenomenon of the crack on the autoclave flange, a three-dimensional model of the autoclave was established based on the Ansys Workbench platform. A new finite element analysis flow for optimizing the design of autoclave teeth was established using the Fluent, Static Structure, and Direct Optimization modules. The paper analyzed and discussed the maximum stress and minimum fatigue life at the corresponding position. The variation trend of stress and fatigue life at the corresponding position after fillet optimization was also discussed. The results showed that the equivalent stress of autoclave teeth without fillet optimization reached the maximum under different fillet sizes. The equivalent stress and fatigue life of the autoclave tooth were the same as the rounded corner size obtained by the optimization design. The optimal global solution could be obtained through the optimization design process. [ABSTRACT FROM AUTHOR]

As the underground space is relatively closed compared to other buildings, the space is hardly connected to the outside world through entrances and exits, which makes it difficult to ventilate and exchange heat with the outside. In this case, it is easy to cause a large number of casualties when a fire breaks out. When the fire happens smoke will be discharged merely by the mechanical exhaust, and air system should work simultaneously to replenish the oxygen inside. By setting four-group models, the paper analyzes the strategies for smoke extraction and air makeup in the underground construction. The paper points out that when the fire happens in a smoke bay, the neighborhood smoke extraction fan should be opened and the air makeup system should not be located at the top to disturb the smoke layer. By comparing and analyzing the performance of the smoke extraction and air conditioning system, the casualties caused by the high temperature toxic smoke from the fire can be reduced as far as possible. [ABSTRACT FROM AUTHOR]

This paper analyzes the modeling of a computer-aided piano music automatic notation algorithm, combines the influence of music on psychological detachment, and designs the piano music automatic notation algorithm in psychological detachment model construction. This paper investigates the multiresolution time-frequency representation constant Q-transform (CQT), which is common in music signal analysis, and finds that although CQT has higher frequency resolution at low frequencies, it also leads to lower temporal resolution. The variable Q-transform is introduced as a tool for multibasic frequency estimation of the time-frequency representation of music signals, which has better temporal resolution than CQT at the exact frequency resolution and efficient coefficient calculation. The short-time Fourier transform and constant Q-transform time-frequency analysis methods are implemented, respectively, and note onset detection and multibasic tone detection are implemented based on CNN models. The network structure, training method, and postprocessing method of CNN are optimized. This paper proposes a temporal structure model for maintaining music coherence to avoid manual input and ensure interdependence between tracks in music generation. This paper also investigates and implements a method for generating discrete music events based on multiple channels, including a multitrack correlation model and a discretization process. In this paper, the automatic piano music notation algorithm can play an influential role in significantly enhancing the actual effect of psychological detoxification. [ABSTRACT FROM AUTHOR]

In order to study the die wear law of rotary fine blanking helical cylindrical gear, a three-dimensional rigid plastic finite element model of rotary fine blanking helical cylindrical gear is established on the Deform-3D software platform. Based on the Archard wear model, this paper analyzes the die wear in the fine blanking process, obtains the wear distribution of each point on the working surface of the die, determines the maximum wear area, and makes a comparative analysis with the fine blanking die wear of spur gear. Through the single factor variable method, this paper studies the effects of reverse jacking force, blank holder force, blanking speed, punch and die clearance, die fillet radius, and die initial hardness on die wear. The test results show that when the punch reduction is the same, the wear of the female die of fine blanking helical cylindrical gear is greater than that of fine blanking spur cylindrical gear. When the counter jacking force increases from 100 kN to 200 kN, the maximum wear of the die gradually increases from 6.91 × 10–6 mm to 9.38 × 10–6 mm; when the blank holder force increases to 3/4 of the blanking force, the die wear decreases with the increase of blank holder force; it is ideal when the blanking clearance is 0.5% t (0.02 mm). Conclusion. The wear model can accurately predict the relationship between main process parameters and wear in the process of rotary fine blanking, and the measures to reduce die wear are put forward from the aspect of process design. [ABSTRACT FROM AUTHOR]

This paper presents the dispersal effect on a prey-predator model with three-patch states incorporating a strong Allee effect on the first two prey populations. The prey species are considered to be mutable to exhibit a balanced dispersal between the patches. The dispersal among patches is directed through lower fit patches to higher fit patches. This paper derives a new approach for dispersal and Allee's effect with the specific condition on the stability on a three-patch of a three-species prey-predator anticipated system. The persistence of the system is observed because of the dispersal effect on the three-patch prey-predator system. The numerical simulations of analytical findings are presented using hypothetical parameter values to relate real-world prey-predator situations for balancing ecology. [ABSTRACT FROM AUTHOR]

As a supplement to traditional teaching methods, computer-assisted teaching methods can reflect modern educational concepts, such as creating student-led, teacher-led environments. The goal of college English education is to enable them to communicate effectively in English in their future academic, work, and social interactions, while also developing students' self-learning skills. Chinese society improves overall cultural competence and adapts to the needs of international communication. Self-directed learning is not static and will increase or decrease with time, discipline, and conditions and is an evolving process. Understanding learning, taking responsibility for one's own learning, and learning how to learn are all beneficial. Students abound in school life and even throughout their lives. In this paper, we try to propose a computer-based method for constructing an independent English learning model based on a practical study of computer network technology for the development of self-learning ability of non-English majors in a university. This paper uses comparative analysis techniques to compare traditional paper-and-pencil examinations and computer-based online evaluations and analyzes the effects of each. The survey showed that 81% of the students preferred the computer-based assessment. Therefore, the focus of this research is to strengthen the oral English training in college and create an authentic English learning environment for students to really feel the standard English pronunciation, intonation, and knowledge of grammar, listening, reading, writing, and translation. [ABSTRACT FROM AUTHOR]

Previous studies mainly used statistical methods to analyze the impact of traffic composition on saturation flow rate from the mesolevel, and there is insufficient research on how traffic composition affects driving behavior. Thus, the purpose of this paper is to establish a more accurate car-following model, establish the relationship between microbehavior and mesostatistical regularity, and explain the influence of vehicle composition on saturation headway. In this paper, an improved full velocity difference (FVD) model is proposed, which abstracts the driver characteristics of a heterogeneous flow into four scenarios: car-car, car-bus, bus-car, and bus-bus. The measured data are used to calibrate and verify the basic FVD and the improved FVD models. The performance of the improved model is significantly improved. The RMSE and RMSPE are reduced by 15.29% and 22.32%, respectively. Finally, through numerical simulation experiments, the variation of saturation headway with different proportions of buses is analyzed. The saturation headway increases with the increase of the proportion of heavy vehicles. Moreover, another important finding is that the saturation headway is not significantly influenced by the position of the buses but only by the proportion of the buses. The research results could provide theoretical support for the control and management of fleets composed of different vehicles at intersections. [ABSTRACT FROM AUTHOR]

In the process of Earth-Moon transfer orbit, many parameters are involved and the degree of influence varies among the parameters. How to accurately distinguish the influence relationship between different parameters is of great significance to engineering missions. Based on Sobol sequence sampling method and Sobol global sensitivity analysis method, a calculation process of global sensitivity analysis is proposed in this paper for high-fidelity Earth-Moon transfer orbit. A numerical simulation method is used to verify that the Sobol sequence sampling method has better convergence and higher precision than other sampling methods and has better adaptability in global sensitivity analysis. The effects of different state parameters and the combination of different parameters on the perilune parameters of Earth-Moon transfer orbit are given by simulation examples, which verifies the effectiveness and feasibility of the calculation process proposed in this paper. Simulation results show that the radial position and tangential velocity at the trans-lunar injection point are the main sensitivity parameters, and the other parameters have little effect on the results. The sensitivity of the orbital elements at the trans-lunar injection point to the perilune parameters is different and needs to be determined according to the specific parameters. The results of this study can provide important reference for future Earth-Moon transfer orbit design and related engineering missions. [ABSTRACT FROM AUTHOR]

In order to deal with the bottleneck of poor plasticity and low formability of magnesium alloys at room temperature, a numerical simulation and a die process optimization method based on hot stamping of AZ series magnesium alloys were proposed. Firstly, based on the PAM-STAMP finite element analysis platform, the thermomechanical coupling numerical simulation is carried out for the cross cup-shaped deep drawing, and the changes in the stress and temperature field during the forming process are analyzed. Aiming at the influence of various process parameters on the plastic formability of magnesium alloys, the effects of sheet metal shape, die fillet size, friction factor, and blank holder force on the forming quality were analyzed through experiments. The experimental results show that under the same conditions such as temperature and blank holder force, the numerical simulation method and the mold process optimized in this paper can be used to form parts that are 25% deeper than the traditional process, and the sheet material can be thinned to the maximum at this time. The amount is 0.152 mm, which verifies the correctness and superiority of the method and process in this paper. [ABSTRACT FROM AUTHOR]

Loess landslides are a major geological disaster in the southeastern Qinghai Province, causing huge economic losses and casualties. The particularity of loess determines the disaster initiation mechanism, disaster mode, genetic mechanism, and complexity of the evolution process. This paper studies the deformation and stability analysis of the Quwajiasa large-scale multislip loess landslide in the Yellow River Basin from the perspective of field investigation, Interferometric Synthetic Aperture Radar (InSAR) monitoring, and numerical simulation. This study determines the deformation characteristics and genetic mechanism of the landslide through on-site field investigation, then quantitatively evaluates the overall deformation of the landslide using InSAR monitoring, locates the strong deformation area, and finally determines the control relationship between the two sliding surfaces on the landslide deformation using FLAC3D numerical simulation, obtaining the stability coefficient of the two sliding surfaces. The landslide is divided into seven engineering geological zones. The deformation history of the landslide is studied using InSAR technology. Results show that the landslide can be divided into significant deformation areas and no significant deformation areas. Two strong deformation areas are found. The FLAC3D numerical simulation results show that the deformation and stability of the right side of landslide are controlled by sliding surface 1, and the deformation and stability of the left side are controlled by sliding surface 2. The landslide is in an unstable state overall. The research done in this paper proposes a basis for the treatment of the Quwajiasa landslide. [ABSTRACT FROM AUTHOR]

This paper studies the aircraft air circulation system and proposes a new architecture of the aircraft air circulation system. Combined with the neural network algorithm, the numerical simulation results of turbine, compressor, and heat exchanger are fitted and predicted, and the accuracy of the simulation model is verified by comparing with the experimental results. Comparing and analyzing the booster, F-15, F-35, and the newly proposed air circulation system, the engine bleed air volume consumed by the system under different flight conditions is obtained. The results show that the newly proposed air circulation system can save up to 71.4% of the engine bleed air compared with the simple boost and 29.8% of the engine bleed air compared with the F-35. The new air circulation system proposed in this paper can effectively improve the energy utilization rate of the system and reduce the consumption of engine bleed air. [ABSTRACT FROM AUTHOR]

After a shale gas reservoir is fractured, hydraulic fractures interweave with natural fractures to form a fracture network. Numerical simulation based on the continuous fracture network model is a relatively economical and convenient method to predict fracture network morphology and size in the field application. However, some important factors, such as fracture height variation and filtration loss, have not been considered in the past continuous fracture network models. Therefore, this paper is aimed at establishing a novel continuous fracture network model to improve simulation accuracy. Firstly, this paper established a method to judge whether natural fractures develop or not. Then, a novel continuous fracture network model considering fracture height variation and asymmetry, filtration loss, fluid flow, and other key factors was established, and the forward algorithm and inverse algorithm of the model were proposed. At last, this model was applied in a field case to verify accuracy, and the average accuracy is more than 90%. Compared with the traditional Meyer software, the average error of prediction was reduced by 7.86%. [ABSTRACT FROM AUTHOR]

The application and economic efficiency evaluation mode of traditional composition in the field of modern music cannot meet the needs of various types of music in China, especially Guqin music. Based on this, this paper studies the big data simulation model of Guqin sound synthesis and plucking based on computer composition technology. The computer composition technology uses the discrete dynamic modeling technology of complex system to complete the computer simulation of Guqin sound through the analysis of the correlation between Guqin music data and realizes the storage and analysis of the generated Guqin sound data. In addition, the technology can analyze the data information of composition mode in the piano sound plucking simulation model with the classical Guqin music data stored in the cloud system over the years and then feed it back to relevant professionals for verification. The experimental results show that the Guqin sound simulation model can efficiently compare and analyze the melody and other data of classical Guqin sound with the simulated Guqin sound and can realize secondary data mining. This paper studies the application of computer composition method based on discrete dynamic modeling technology in Guqin sound simulation, which has certain reference significance for improving the cloud data in China's modern music field and the intelligent construction of Guqin sound data cloud storage system. [ABSTRACT FROM AUTHOR]

In this paper, a series of studies are carried out on the hidden karst encountered in the excavation of Baziling tunnel. In this paper, the safe thickness of the water-resisting layer in a hidden karst cave and tunnel is studied by means of engineering geological investigation, numerical simulation, and neural network. The numerical calculation model is established through the geological survey. Innovate to use BP neural network and differentiation algorithm to inverse the rock mechanical parameters. By analyzing the influence of different thicknesses of the water-resisting layer on the deformation and failure of surrounding rock, the final thickness of the water-resisting layer is obtained. At the same time, the influence of water pressure on the thickness of the water-resisting layer is studied, and the treatment scheme under different water pressure is finally determined. [ABSTRACT FROM AUTHOR]

The interval section of the Liuyang River flood control levee project of the Changsha Metro Line 6 is used as the engineering background of this study. A three-dimensional finite element numerical model of a tunnel shield containing complex interfaces is established by using the multifield coupling software COMSOL. The paper studied the deformation of flood control levees under shield tunnel excavation working conditions. The results show that when the left line shield machine is excavated below the Liuyang River flood control levee, the deformation of the flood control levee and the surrounding rock of the tunnel is biased towards the built right line tunnel. And it has an impact on the bridge pile near the tunnel. When the shield of the left line crosses the flood control levee, it can easily cause a large deformation and displacement of the levee above the area between the two shields. To ensure the controlled deformation of the levee, the construction should ensure the spacing between the two tunnel palm faces as far as possible and should be far away from other structures on the levee. When the shield crosses the levee, the deformation that occurs at the base of the levee is significantly higher than the deformations that occur at other locations of the levee. Displacement monitoring and secondary reinforcement at the base of the flood control levee appear to be necessary. The numerical simulation results validate the feasibility of using the multifield coupling software COMSOL to study the construction modeling of shield tunnels through rivers and its advantages. This method provides a practical framework for similar tunnel performance engineering or displacement monitoring in future projects. [ABSTRACT FROM AUTHOR]

The ice crystal supercooled droplet mixed phase icing problem is an important research direction in aircraft icing and has received more attention in recent years. The thermodynamic process of the water film after the ice crystals impact on the surface determines the final ice shape, which is an important part of the accurate prediction of aircraft icing. In this paper, a thermodynamic model of ice crystal supercooled droplet mixed phase icing is proposed based on the extended Messinger model, according to the results of flow field and particle trajectory calculations. In this model, the mass and energy conservation equations of ice crystals, supercooled droplets, and liquid water are considered. The equations take the process of ice crystal adhesion and erosion into account, and the solution method of the equations is given. Ice shapes are calculated under various ice crystal supercooled droplet mixed phase conditions and compared with experimental results to demonstrate the validity of the numerical method. The effects of ice crystal erosion rate, melting ratio, and adhesion coefficient on the calculation results are analyzed by a numerical method. The results show that the ice crystal erosion rate has little effect on the ice shape, while a larger melting ratio and adhesion coefficient lead to more ice accretion. [ABSTRACT FROM AUTHOR]

The squeezed multiple-branch pile is a variable section pile that was built by adding a bearing branch cavity to a constant section pile using expansion and extrusion equipment. It is widely used in engineering practice for its high bearing capacity, small settlement deformation, high economic benefits, strong adaptability, and simple pile forming process. In this paper, a new type of squeezed multiple-branch pile is proposed and its forming tool is invented. The forming tool of the pile has applied for an invention patent and is authorized by the China National Intellectual Property Administration. Multiple groups of comparison models of the new squeezed multiple-branch piles are established by using FLAC3D numerical simulation software to investigate the influence of the number and spacing of branches on the bearing mechanism in response to uplift load. The results indicated that the number and spacing of branches have a significant effect on the uplift bearing capacity, load–displacement curves, side friction resistance, and stress distribution law in the new pile and soil around the pile. The suitable number and spacing of branches maximize the uplift bearing capacity and minimize the settlement of a single pile. [ABSTRACT FROM AUTHOR]

In this paper, we consider a general time-space discrete host-parasitoid model with the periodic boundary conditions. We analyzed and obtained some usual conditions, such as Turing instability occurrence, Flip bifurcation occurrence, and Neimark-Sacker bifurcation occurrence. We also find several multiple bifurcation phenomena, such as 1 : 2 Resonance, Neimark-Sacker-Flip bifurcation, Neimark-Sacker-Neimark-Sacker bifurcation, Neimark-Sacker-Flip-Flip bifurcation, induced by diffusion. In a modified Nicholson-Bailey model, employing the mutual interference and diffusive interaction as bifurcation parameters, there appear route from standing Turing instability to multiple bifurcations by changing diffusive parameters. Some numerical simulations of the modified Nicholson-Bailey model support these corollaries. [ABSTRACT FROM AUTHOR]

It is of great significance to identify structural state-parameters and the unknown seismic inputs using partial measurements of structural acceleration responses for the rapid evaluation of structures after unknown seismic excitations. However, unknown seismic inputs do not directly appear in the observation equations of measured absolute floor accelerations of building structures, i.e., there is no direct feedthrough of unknown seismic inputs in the observation equations. Current methods for the identification of joint structural systems and unknown inputs are either inapplicable or greatly influenced by measurement noises. In this paper, a method so-called smoothing extended Kalman filter with unknown input without direct feedthrough (smoothing EKF-UI-WDF) is proposed. The identification algorithm is derived in the framework of minimum-variance unbiased estimation (MVUE), and the smoothing technique is adopted to introduce subsequent observation steps in the current identification step. Then, structural states, parameters, and unknown seismic excitations without direct feedthrough are simultaneously identified recursively with only a few steps delay, and the identification results are tolerant to measurement noises. The proposed method is verified by a numerical simulation model and a practical engineering case study. Both identification results validate the effectiveness of the proposed method for the simultaneous identification of structural systems and seismic inputs without direct feedthrough. [ABSTRACT FROM AUTHOR]

A guidance approach with obstacle avoidance is proposed for maneuvering target interception. Firstly, by decomposing the constrained optimal guidance problem into two associated subproblems, the overall scheme of guidance is presented. Secondly, to improve the guidance accuracy against the maneuvering target, an MPC controller with disturbance estimation is designed, which transforms the global optimization problem into a finite-horizon optimal control problem. An auxiliary controller is also developed to ensure the system's stability. Then, to achieve obstacle avoidance without affecting the guidance accuracy, a unified function is built to assess the threats from obstacles of different shapes, based on which the optimal guidance-obstacle avoidance model is established. Finally, to solve the above optimization problems, a hybrid solver is developed based on the adaptive moment estimation (Adam) algorithm, whose output will serve as the real-time guidance command. The numerical simulation results show that the guidance approach presented in this paper can achieve precise guidance and obstacle avoidance in various scenarios, and the Monte Carlo experiment further demonstrates the robustness and computation efficiency of the approach. [ABSTRACT FROM AUTHOR]

This paper studies Lyapunov stability at a point and its application in the Cournot duopoly game. We first explore the relationship between Lyapunov stability at a point, nonsensitivity and non-Devaney chaos and find that a dynamical system is nonsensitive and non-Devaney chaotic if there is a point in this system such that it is Lyapunov stable at that point. We next prove a group of equivalent characterizations of Lyapunov stability at a point to deduce the composite theorems and product theorems of Lyapunov stability at a point, and then we prove three equivalent characterizations of the Cournot duopoly system to demonstrate that this system is Lyapunov stable at its unique nonzero fixed point (Cournot equilibrium point) when the unit costs of the Cournot double oligarchies satisfy certain conditions. Therefore, we conclude that the Cournot duopoly system is safe relative to both sensitivity and Devaney chaos. The robustness of our results are also verified by conducting numerical simulations in the Cournot duopoly game. [ABSTRACT FROM AUTHOR]

In this paper, a novel Kenics static mixer applied in a direct-contact heat exchanger (DCHE) was proposed in order to enhance the heat transfer efficiency. The computational fluid dynamics (CFD) simulation method was adopted to investigate the effect of the continuous phase and dispersed phase on direct-contact heat transfer (DCHT) in the Kenics static mixer. The perforation index (PI) was introduced to depict the performance of the Kenics static mixer, and the effect of different numbers of openings at three initial heat transfer temperature differences (at the inlet of the continuous and dispersed phases) was studied. The simulation results showed that under the same working conditions, a larger initial temperature difference would result in greater differences in the fluid uniformity index (UI), turbulence intensity, and time evolution of a gaseous working substance. The increase of hole numbers and decrease of hole diameters can optimize the DCHT. Under three initial temperature differences, the heat transfer efficiency for the 6-hole and 9-hole Kenics DCHEs was about 20% higher than the Kenics DCHE without holes. [ABSTRACT FROM AUTHOR]

Considering the stringent requirement of the pointing accuracy up to 2.5″ of the world's largest full steerable radio telescope, this paper studies the welding experiment of the azimuth track of the antenna. First, the opposite deformation jig and welding process were designed for the QTT's azimuth track. Then, the welding process was numerically simulated using a finite element model. The simulation results show that a better welding effect will be obtained by appropriately reducing the opposite force on the basis of the original. The three deformation processes of the track are regulated by the opposite deformation jig. The results show that the opposite deformation jig designed for QTT's azimuth track can make the amount of deformation and flatness meet the design requirements. Finally, nondestructive testing was carried out to check the welding quality of the track surface and interior. The results show that there are no obvious defects in the welds of the azimuth track. The constraint jig and welding processes designed for QTT are effective and feasible. [ABSTRACT FROM AUTHOR]

In this paper, considering the mooring system can be taut-slack in the motion, the dynamic equations of the mooring system are derived by using the theory of large deformation. The nonlinear dynamic response of semitensioned mooring line is numerically simulated. Assuming the platform motion is known, the effect of platform on mooring line is simplified as an end-point excitation. Directly using the finite difference method for numerically solving partial differential equations of mooring line, the dynamic responses can be obtained. Then, the causes about the nonlinear state are analyzed, and the location where the taut-slack phenomenon occurs can be located by calculating the tension of mooring. The results show that the mooring line is more likely to be taut-slack under tangential excitation with the tension change, while the mooring remains taut under normal excitation. The taut-slack state of the mooring line is concentrated near the anchor point. Through the amplitude-frequency curve and bifurcation point set, it is found that the taut-slack region is accompanied by multiperiod motion. And the taut-slack phenomenon will lead to the unstable motion. [ABSTRACT FROM AUTHOR]

In this paper, a saltwater intrusion model, in view to study the dynamics of the interface between the saltwater and the freshwater in a coastal aquifer, is established. This dynamic is caused by an injection of saltwater and a freshwater pumping through a well located in a given position. From the flow model in each phase, we defined an appropriate hypothesis to obtain our global model based only on the height of the interface. The numerical simulation of our model led us to study the effect of the parameters and obtain some empirical laws of the pollution time versus the distance well-injection area and pollution time versus the pumping flow. [ABSTRACT FROM AUTHOR]

In this paper, a saltwater intrusion model, in view to study the dynamics of the interface between the saltwater and the freshwater in a coastal aquifer, is established. This dynamic is caused by an injection of saltwater and a freshwater pumping through a well located in a given position. From the flow model in each phase, we defined an appropriate hypothesis to obtain our global model based only on the height of the interface. The numerical simulation of our model led us to study the effect of the parameters and obtain some empirical laws of the pollution time versus the distance well-injection area and pollution time versus the pumping flow. [ABSTRACT FROM AUTHOR]

This work presents two versions of landing gear drives numerically simulated. We follow to obtain the right driving sequence of the legs and doors and the estimation of the landing gear deploy and retract time. Although the studies in this paper do not exhaust all the aspects concerning landing gear hydraulic system functioning, these are useful in the design phase of the aircraft hydraulic systems. Regarding the landing gear hydraulic system, we highlight one version of the drive stall phenomenon. When the hydraulic feeding pressure decreases, it is possible that the forces developed by the hydraulic cylinders are enough to retract completely the legs. The landing gear remains in an intermediate position, and the aircraft cannot accomplish its mission safely. For a second version, logic command functions are synthesized using Karnaugh diagrams, and after that, the numerical simulation is accomplished to validate the solution. We used the AMESim software to perform numerical simulations. [ABSTRACT FROM AUTHOR]

In this paper, the general framework for calculating the stability of equilibria, Hopf bifurcation of a delayed prey-predator system with an SI type of disease in the prey population, is investigated. The impact of the incubation period delay on disease transmission utilizing a nonlinear incidence rate was taken into account. For the purpose of explaining the predation process, a modified Holling type II functional response was used. First, the existence, uniform boundedness, and positivity of the solutions of the considered model system, along with the behavior of equilibria and the existence of Hopf bifurcation, are studied. The critical values of the delay parameter for which stability switches and the nature of the Hopf bifurcation by using normal form theory and center manifold theorem are identified. Additionally, using numerical simulations and a hypothetical dataset, various dynamic characteristics are discovered, including stability switches, chaos, and Hopf bifurcation scenarios. [ABSTRACT FROM AUTHOR]

This paper describes recent advances in the effect of soil creep on the time-dependent deformation of deep braced excavation. The effect of soil creep is generally investigated using the observational method and the plain-strain numerical simulation method. The observational method is more applicable for deep braced excavations in soft clays constructed using the top-down method. The plain-strain numerical simulation method can be conveniently used for parametric analysis, but it is unable to capture the spatial characteristics of soil creep effect on lateral wall deflections and ground movements. The additional lateral wall deflections and ground movements that are generated due to the soil creep effect can account for as large as 30% of the total displacements, which highlights the importance of considering the effect of soil creep in deep braced excavations through soft clays. The magnitude of the displacements due to soil creep depends on various factors, such as excavation depth, elapsed period, unsupported length, and strut stiffness. Parametric analyses have indicated several effective measures that can be taken in practice to mitigate the detrimental effect of soil creep on the deformation of deep braced excavation. Based on the literature review, potential directions of the related future research work are discussed. This paper should be beneficial for both researchers and engineers focusing on mitigating the adverse effect of soil creep on the stability of deep braced excavations. [ABSTRACT FROM AUTHOR]

A submerged floating tunnel (SFT) is considered an innovative alternative to conventional bridges and underground or immersed tunnels for passing through deep water. Assessment of hydrodynamic performance of SFT under regular wave loading is one of the important factors in the design of SFT structure. In this paper, a theoretical hydrodynamic model is developed to describe the coupled dynamic response of an SFT and mooring lines under regular waves. In this model, wave-induced hydrodynamic loads are estimated by the Morison equation for a moving object, and the simplified governing differential equation of the tunnel with mooring cables is solved using the fourth-order Runge–Kutta and Adams numerical method. The numerical results are successfully validated by direct comparison against published experimental data. On this basis, the effects of the parameters such as the cable length, buoyancy-weight ratio, wave period, wave steepness, and water/submergence depth on the dynamic response of the SFT under wave loading are studied. The results show that tunnel motions and cable tensions grow with wave height and period and decrease with submergence depth. The resonance of the tunnel will be triggered when the wave period is close to its natural vibration period, and the estimation formula of wave period corresponding to tunnel resonance is proposed in this paper. [ABSTRACT FROM AUTHOR]

Hydraulic fracturing is a necessary measurement to realize the commercial exploitation of oil and gas, but its application in multilayered thin tight sandstone gas reservoirs is still not perfect, which usually have thin gas layers mixed with complex intervals, and shows a dramatic variation in geological and geomechanical properties in the vertical direction. When conventional hydraulic fracturing methods are applied to this kind of reservoir, it is hard to get proper fracture propagation, especially for fracture height control. Facing this situation, this paper proposes a numerical study of the hydraulic fracturing mechanism and analyzes its influencing factors in the multilayered thin tight sandstone gas reservoir. Relying on a real reservoir in the Ordos Basin in China, relevant geological and geomechanical parameters of major gas layers and interlayers are obtained. According to these parameters, the hydraulic fracturing simulation in the multilayered thin tight gas reservoir model is carried out, based on which, the sensitivity analysis of different geological and fracturing parameters which affect the fracture propagation is performed. Furthermore, a real low-production well after fracturing in this kind of reservoir is selected as an example, and based on the analysis, an optimized fracturing scheme is proposed to adapt to the characteristics of the reservoir. According to the comparison of fracturing and production simulations, the optimized fracturing scheme can prevent hydraulic fractures from breaking through thin interlayers, control the fracture height, and prevent fractures from communicating strata with a high water-bearing layer. At the same time, with the same amount of proppant and fracturing fluid, longer fracture length and better fracture conductivity are created, so that the productivity of the optimized fracture has been greatly improved. [ABSTRACT FROM AUTHOR]

Intraventricular conduction disturbances (IVCD) are currently generally accepted as ECG diagnostic categories. They are characterized by defined QRS complex patterns that reflect the abnormalities in the intraventricular sequence of activation that can be caused by pathology in the His-Purkinje conduction system (HP) or ventricular myocardium. However, the current understanding of the IVCD's underlying mechanism is mostly attributed to HP structural or functional alterations. The involvement of the working ventricular myocardium is only marginally mentioned or not considered. This opinion paper is focused on the alterations of the ventricular working myocardium leading to the most frequent IVCD pattern—the left bundle branch block pattern (LBBB). Recognizing the underlying mechanisms of the LBBB patterns and the involvement of the ventricular working myocardium is of utmost clinical importance, considering a patient's prognosis and indication for cardiac resynchronization therapy. [ABSTRACT FROM AUTHOR]

Intraventricular conduction disturbances (IVCD) are currently generally accepted as ECG diagnostic categories. They are characterized by defined QRS complex patterns that reflect the abnormalities in the intraventricular sequence of activation that can be caused by pathology in the His-Purkinje conduction system (HP) or ventricular myocardium. However, the current understanding of the IVCD's underlying mechanism is mostly attributed to HP structural or functional alterations. The involvement of the working ventricular myocardium is only marginally mentioned or not considered. This opinion paper is focused on the alterations of the ventricular working myocardium leading to the most frequent IVCD pattern—the left bundle branch block pattern (LBBB). Recognizing the underlying mechanisms of the LBBB patterns and the involvement of the ventricular working myocardium is of utmost clinical importance, considering a patient's prognosis and indication for cardiac resynchronization therapy. [ABSTRACT FROM AUTHOR]