Search

Remaining useful life prediction is an important way to improve the durability and reduce the cost of the proton exchange membrane fuel cell. This paper presents a novel method to predict the remaining useful life of proton exchange membrane fuel cell under different load currents based on support vector regression and grey wolf optimizer algorithm. The proposed method considers the influence of 17 operating conditions and historical voltage. Firstly, the measured data are reconstructed through robust locally weighted smoothing method to reduce the calculation amount and filter disturbances. Then, support vector regression with fewer hyperparameters is used to establish the degradation model. Finally, the hyperparameters of support vector regression are optimized through grey wolf optimizer algorithm to improve the accuracy of degradation prediction. The proposed method is validated by two degradation experiments under different load currents. The test results show that grey wolf optimizer algorithm can effectively improve the accuracy of degradation prediction based on support vector regression. Compared with other methods, the proposed method has the highest accuracy. The proposed method can predict the fuel cell degradation with a mean absolute percentage error of less than 0.3%. The proposed method can predict the remaining useful life of 492 hours. [ABSTRACT FROM AUTHOR]

In this paper, we design and analyze Mc2g (Matrix Completion with 2 Graphs), an efficient algorithm that performs matrix completion in the presence of social and item similarity graphs. Mc2g runs in quasilinear time and is parameter free. It is based on spectral clustering and local refinement steps. For the matrix completion problem which possesses additional block structures in its rows and columns, we derive the expected number of sampled entries required for Mc2g to succeed, and further show that it matches an information-theoretic lower bound up to a constant factor for a wide range of parameters. We perform extensive experiments on both synthetic datasets and a semi-real dataset inspired by real graphs. The experimental results show that Mc2g outperforms other state-of-the-art matrix completion algorithms. [ABSTRACT FROM AUTHOR]

Power flow analysis is a key tool for planning, operation and control of power systems. With future hybrid Supergrids in mind, a wide variety of power flow algorithms for multi-terminal VSC AC/DC systems have been proposed. However, the nonlinear nature of these formulations represents a challenge for its use in real power systems. Whereas in the study of AC networks linear approximations are frequently utilized to speed up multi-scenario steady-state analysis, an equivalent tool has not been proposed for hybrid AC/DC grids. This paper fills that gap by formulating a linear MW-only power flow algorithm with losses for multi-terminal VSC AC/DC systems. The proposed algorithm provides a consistent estimation of converters' losses and allows modelling of all branches within the converter stations. Moreover, two novel schemes for the inclusion of DC network losses are proposed and a circuit-equivalent model of the linear power flow problem in multi-terminal VSC AC/DC systems is suggested. [ABSTRACT FROM AUTHOR]

In this paper, we study the formalism of unsupervised multi-class domain adaptation (multi-class UDA), which underlies a few recent algorithms whose learning objectives are only motivated empirically. Multi-Class Scoring Disagreement (MCSD) divergence is presented by aggregating the absolute margin violations in multi-class classification, and this proposed MCSD is able to fully characterize the relations between any pair of multi-class scoring hypotheses. By using MCSD as a measure of domain distance, we develop a new domain adaptation bound for multi-class UDA; its data-dependent, probably approximately correct bound is also developed that naturally suggests adversarial learning objectives to align conditional feature distributions across source and target domains. Consequently, an algorithmic framework of Multi-class Domain-adversarial learning Networks (McDalNets) is developed, and its different instantiations via surrogate learning objectives either coincide with or resemble a few recently popular methods, thus (partially) underscoring their practical effectiveness. Based on our identical theory for multi-class UDA, we also introduce a new algorithm of Domain-Symmetric Networks (SymmNets), which is featured by a novel adversarial strategy of domain confusion and discrimination. SymmNets affords simple extensions that work equally well under the problem settings of either closed set, partial, or open set UDA. We conduct careful empirical studies to compare different algorithms of McDalNets and our newly introduced SymmNets. Experiments verify our theoretical analysis and show the efficacy of our proposed SymmNets. In addition, we have made our implementation code publicly available. [ABSTRACT FROM AUTHOR]

This paper proposes an online multi-camera multi-object tracker that only requires monocular detector training, independent of the multi-camera configurations, allowing seamless extension/deletion of cameras without retraining effort. The proposed algorithm has a linear complexity in the total number of detections across the cameras, and hence scales gracefully with the number of cameras. It operates in the 3D world frame, and provides 3D trajectory estimates of the objects. The key innovation is a high fidelity yet tractable 3D occlusion model, amenable to optimal Bayesian multi-view multi-object filtering, which seamlessly integrates, into a single Bayesian recursion, the sub-tasks of track management, state estimation, clutter rejection, and occlusion/misdetection handling. The proposed algorithm is evaluated on the latest WILDTRACKS dataset, and demonstrated to work in very crowded scenes on a new dataset. [ABSTRACT FROM AUTHOR]

Edge federated learning (FL) is an emerging paradigm that trains a global parametric model from distributed datasets based on wireless communications. This paper proposes a unit-modulus over-the-air computation (UMAirComp) framework to facilitate efficient edge federated learning, which simultaneously uploads local model parameters and updates global model parameters via analog beamforming. The proposed framework avoids sophisticated baseband signal processing, leading to low communication delays and implementation costs. Training loss bounds of UMAirComp FL systems are derived and two low-complexity large-scale optimization algorithms, termed penalty alternating minimization (PAM) and accelerated gradient projection (AGP), are proposed to minimize the nonconvex nonsmooth loss bound. Simulation results show that the proposed UMAirComp framework with PAM algorithm achieves a smaller mean square error of model parameters’ estimation, training loss, and test error compared with other benchmark schemes. Moreover, the proposed UMAirComp framework with AGP algorithm achieves satisfactory performance while reduces the computational complexity by orders of magnitude compared with existing optimization algorithms. Finally, we demonstrate the implementation of UMAirComp in a vehicle-to-everything autonomous driving simulation platform. It is found that autonomous driving tasks are more sensitive to model parameter errors than other tasks since the neural networks for autonomous driving contain sparser model parameters. [ABSTRACT FROM AUTHOR]

We examine the problem of uncovering communities in complex real-world networks whose elements and their respective associations manifest as streams of data. Community detection is applied in emerging computational environments and concerns critical applications in diverse areas including social computing, web analysis, IoT and biology. Despite the already expended related research efforts, the task of revealing the community structure of massive and rapidly-evolving networks remains very challenging. More specifically, there is an emerging need for online approaches that ingest graph data as a stream. In this paper, we propose a streaming-graph community-detection algorithm that expands seed-sets of nodes to communities. We consider an online setting and process a stream of edges while aiming to form communities on-the-fly using partial knowledge of the graph structure. We use space-efficient structures to maintain very limited information regarding the nodes of the graph and the sought communities, so as to effectively process large scale networks. In addition to our novel streaming approach, we develop a technique that increases the accuracy of our algorithm considerably and additionally propose a new clustering algorithm that allows for automatically deriving the size of the communities we seek to detect. Using ground-truth communities for a wide range of large real-word and synthetic networks, our experimental evaluation shows that our approach does achieve accuracy comparable, and oftentimes better, to the state-of-the-art non-streaming community detection algorithms. More importantly, we attain significant improvements in both execution time and memory requirements. [ABSTRACT FROM AUTHOR]

Density Peak Clustering (DPC), a popular density-based clustering approach, has received considerable attention from the research community primarily due to its simplicity and fewer-parameter requirement. However, the resultant clusters obtained using DPC are influenced by the sensitive parameter $d_c$ d c , which depends on data distribution and requirements of different users. Besides, the original DPC algorithm requires visiting a large number of objects, making it slow. To this end, this paper investigates index-based solutions for DPC. Specifically, we propose two list-based index methods viz. (i) a simple List Index, and (ii) an advanced Cumulative Histogram Index. Efficient query algorithms are proposed for these indices which significantly avoids irrelevant comparisons at the cost of space. For memory-constrained systems, we further introduce an approximate solution to the above indices which allows substantial reduction in the space cost, provided that slight inaccuracies are admissible. Furthermore, owing to considerably lower memory requirements of existing tree-based index structures, we also present effective pruning techniques and efficient query algorithms to support DPC using the popular Quadtree Index and R-tree Index. Finally, we practically evaluate all the above indices and present the findings and results, obtained from a set of extensive experiments on six synthetic and real datasets. The experimental insights obtained can help to guide in selecting a befitting index. [ABSTRACT FROM AUTHOR]

Recent advances in noiseless non-adaptive group testing have led to a precise asymptotic characterization of the number of tests required for high-probability recovery in the sublinear regime $k = n^{\theta }$ (with $\theta \in (0,1)$), with $n$ individuals among which $k$ are infected. However, the required number of tests may increase substantially under real-world practical constraints, notably including bounds on the maximum number $\Delta $ of tests an individual can be placed in, or the maximum number $\Gamma $ of individuals in a given test. While previous works have given recovery guarantees for these settings, significant gaps remain between the achievability and converse bounds. In this paper, we substantially or completely close several of the most prominent gaps. In the case of $\Delta $ -divisible items, we show that the definite defectives (DD) algorithm coupled with a random regular design is asymptotically optimal in dense scaling regimes, and optimal to within a factor of e more generally; we establish this by strengthening both the best known achievability and converse bounds. In the case of $\Gamma $ -sized tests, we provide a comprehensive analysis of the regime $\Gamma = \Theta (1)$ , and again establish a precise threshold proving the asymptotic optimality of SCOMP (a slight refinement of DD) equipped with a tailored pooling scheme. Finally, for each of these two settings, we provide near-optimal adaptive algorithms based on sequential splitting, and provably demonstrate gaps between the performance of optimal adaptive and non-adaptive algorithms. [ABSTRACT FROM AUTHOR]

Cooperative Vehicle-Infrastructure System (CVIS) can provide innovative services for traffic management and enable trips to be safer, more coordinated, and smarter. In the CVIS, the vehicles upload crowd sensing data to the Vehicular Edge Computing (VEC) server for quick data fusion and informed decision-making. However, with the ever-increasing number of vehicles, the VEC server cannot undertake massive computation-intensive tasks due to the limited edge computing capabilities. In this paper, we propose a reverse offloading framework that can fully utilize the vehicular computation resource to relieve the burden of the VEC server and further reduce the system latency. Under the proposed offloading framework, the binary reverse offloading (BRO) and partial reverse offloading (PRO) strategies are designed for two types of tasks, i.e., non-partitioned tasks and partitioned tasks. We formulate the system latency minimization problem by optimizing reverse offloading decisions, and the communication and computation resources allocation. Due to the non-convex and existing variables coupling, the original problem is transformed into the equivalent weighted-sum optimization problem. Based on the alternative optimization, we decouple the weighted-sum optimization problems into the two subproblems, and the closed-form expressions of transmission power and computation frequency of vehicles and RSU are derived. Low complexity greedy based efficient searching (GES) algorithm and joint alternative optimization based bi-section searching (JAOBSS) algorithm are proposed for BRO and PRO strategies, respectively. The algorithm complexity and performance bounds are analyzed. Simulation results show that the proposed GES algorithm can achieve optimal performance with low complexity. Besides, the proposed GES and JAOBSS algorithms can significantly improve the performance compared with other baseline schemes by 6.14% and 13.46% at least. [ABSTRACT FROM AUTHOR]

When imaging through a semi-reflective medium such as glass, the reflection of another scene can often be found in the captured images. It degrades the quality of the images and affects their subsequent analyses. In this paper, a novel deep neural network approach for solving the reflection problem in imaging is presented. Traditional reflection removal methods not only require long computation time for solving different optimization functions, their performance is also not guaranteed. As array cameras are readily available in nowadays imaging devices, we first suggest in this paper a multiple-image based depth estimation method using a convolutional neural network (CNN). The proposed network avoids the depth ambiguity problem due to the reflection in the image, and directly estimates the depths along the image edges. They are then used to classify the edges as belonging to the background or reflection. Since edges having similar depth values are error prone in the classification, they are removed from the reflection removal process. We suggest a generative adversarial network (GAN) to regenerate the removed background edges. Finally, the estimated background edge map is fed to another auto-encoder network to assist the extraction of the background from the original image. Experimental results show that the proposed reflection removal algorithm achieves superior performance both quantitatively and qualitatively as compared to the state-of-the-art methods. The proposed algorithm also shows much faster speed compared to the existing approaches using the traditional optimization methods. [ABSTRACT FROM AUTHOR]

When dealing with complex nonlinear signals in intelligent system, by defining the inner product of two data vectors in the feature space, the kernel function can reflect the nonlinear mapping relationship between reproducing kernel Hilbert space (RKHS) and original data space. Therefore, by implementing classical linear adaptive filtering in RKHS space, the filtering operation can be expressed as a special relation of inner product with kernel function, which is referred to as “kernel trick.” As long as these algorithms can be expressed in the form of inner product, not only the convex least squares problem can be solved iteratively, but also the nonlinear adaptive filtering algorithms can be obtained, which have both general approximation characteristics and convexity. Therefore, the combination of kernel method and adaptive filtering algorithm is realized. On the other hand, since the Gram matrix is used, the dimension of kernel adaptive algorithm is determined by the number of data samples. When the number of observation sample point is increasing, the size of the state space increases exponentially with the growth of the dimension. Thereby, the kernel adaptive algorithm should solve the problem of online sparsification to avoid “curse of dimensionality.” As part II, based on online sparse kernel learning and the classical adaptive filtering algorithm, the kernel adaptive algorithms and online sparse algorithms are investigated in this paper. The main works of this paper have two aspects. First, combined with classical adaptive algorithm and kernel feature mapping, this paper investigates the basic concept of kernel adaptive algorithm and the realization mechanism of four kernel adaptive algorithm intensively: 1) kernel least mean squares; 2) kernel recursive least squares; 3) kernel affine projection algorithm; and 4) kernel principal component analysis. Second, in order to reduce the computational complexity, this paper studies some online sparse algorithms which include novel criterion, approximate linear dependency, sliding window, coherence criterion, surprise criterion, and so on. Finally, this paper summarizes the essence of existing conclusions of above algorithms and perspectives the future research direction. [ABSTRACT FROM AUTHOR]

For a class of stochastic nonlinear systems in pure-feedback form with dead-zone input and multiple time-varying delays, a novel neural network (NN)-based adaptive control approach is presented in this paper through the use of backstepping approach and dynamic surface technique. By choosing proper Lyapunov–Krasovskii functionals, utilizing the characteristic of hyperbolic tangent functions and adopting the function separation technique, difficulties of controller design that introduced by the time-varying delays can be dealt with properly. Moreover, all unknown nonlinear functions are lumped together and approximated by the NN. Additionally, any information over the boundedness of dead-zone parameters is not needed in the process of controller design. The control scheme proposed in this paper ensures the boundedness in probability of all signals in the closed-loop system, besides, excellent performance of arbitrarily small tracking error will be achieved by selecting control parameters appropriately. At last, two numerical simulation examples are provided to verify the validity of the designed algorithm. [ABSTRACT FROM AUTHOR]

The aim of this paper is to investigate the sensorless voltage control schemes for the promising wound-rotor brushless doubly-fed induction generator (BDFIG) in both the stand-alone and grid-connected systems. For sensorless target, a new rotor position observer using the space vector flux relations of BDFIG is suggested. The proposed sensorless algorithm does not require any additional observers for obtaining the generator speed by directly detecting the rotor position, which may reduce the cost of the overall control system. For the voltage control purpose, a direct voltage control (DVC) scheme is applied for the stand-alone systems. However, this control strategy did not handle the control of the generated-voltage phase angle and also did not consider the phase sequence issue which are very essential provisions for the smooth connection target in grid-connected applications. Hence, DVC strategy cannot guarantee all the intended provisions for a soft and smooth connection process with the grid side and therefore, an effective grid-synchronization algorithm is proposed. A comprehensive analysis to confirm the functionality of the proposed control strategies is discussed through both simulation and experimental results. The presented study in this paper verifies the efficacy of the proposed schemes for sensorless voltage control target of BDFIG in both the stand-alone and grid-connected applications with a good transient behavior. [ABSTRACT FROM AUTHOR]

This paper addresses the incorporation of transmission switching in the contingency-constrained unit commitment problem within the context of co-optimized electricity markets for energy and reserves. The proposed generation scheduling model differs from existing formulations due to the joint consideration of four major complicating factors. First, transmission switching actions are considered both in the pre- and post-contingency states, thereby requiring binary post-contingency variables. Secondly, generation scheduling and transmission switching actions are co-optimized. In addition, the time-coupled operation of generating units is precisely characterized. Finally, practical features of modern power systems, such as uncertain nodal net injections and the operation of energy storage, are also considered. The proposed model is cast as a challenging mixed-integer program for which the off-the-shelf software customarily used for simpler models may lead to intractability even for moderately-sized instances. In order to circumvent this computational issue, this paper presents an enhanced and novel application of an exact nested column-and-constraint generation algorithm featuring the inclusion of valid constraints to improve the overall computational performance. Numerical simulations based on the IEEE 118- and 300-bus systems demonstrate the effective performance of the proposed approach as well as its economic and operational advantages over existing models disregarding post-contingency transmission switching. [ABSTRACT FROM AUTHOR]

Determining contingency aware dispatch decisions by solving a security-constrained optimal power flow (SCOPF) is challenging for real-world power systems, as the high problem dimensionality often leads to impractical computational requirements. This problem becomes more severe when the SCOPF has to be solved not only for a single instance, but for multiple periods, e.g. in the context of electricity market analyses. This paper proposes an algorithm that identifies the minimal set of constraints that exactly define the space of feasible nodal injections for a given network and contingency scenarios. By internalizing the technical limits of the nodal injections and enforcing a minimal worst-case impact of contingencies to line flows, computational effort can be further improved. The case study applies and analyzes the methods on the IEEE 118 and A&M 2000 bus systems, as well as the German and European transmission systems. In all tested cases the proposed algorithm identifies at least 95% of the network and security constraints as redundant, leading to significant SCOPF solve time reductions. Scalability and practical implementation are explicitly discussed. The code and input data of the case study is published supplementary to the paper under an open-source license. [ABSTRACT FROM AUTHOR]

This paper concerns the deployment problem of wireless sensor networks (WSNs) with mobile robotic sensor nodes for spatiotemporal monitoring. The proposed approach, deep reinforced learning tree (DRLT), utilizes deep reinforcement learning (DRL) to improve the efficiency of searching the most informative sampling locations. The parameterized sampling locations in an infinite horizon space are modeled according to their spatiotemporal correlations and subject to various constraints, including field estimation error and information gain. And the model-based information gain can be calculated efficiently over an infinite horizon. In this manner, the effectiveness of the sampling locations is learned through DRLT during the exploration by the robotic sensors. Then DRLT can instruct the robotic sensors to avoid unnecessary sampling locations in future iterations. Also, it is proved in this paper that the proposed algorithm is capable of searching for the near-optimal sampling locations effectively and guaranteeing a minimum field estimation error. Simulation based on national oceanic and atmospheric administration (NOAA) datasets is presented, which demonstrates the significant enhancements made by the proposed algorithm. Compared with the traditional approaches, such as the information theory-based greedy approach or random sampling, the proposed method shows a superior performance with regard to both estimation error and planning efficiency. [ABSTRACT FROM AUTHOR]

This paper establishes an approximate optimal critic learning algorithm based on single neural network (NN) policy iteration (PI) aiming at solving for continuous-time (CT) 2-player zero-sum games (ZSGs). In fact, we have to face the problem that the errors will disturb the dynamics and in turn identifying dynamics will generate errors. In order to prevent the effect of errors, in this paper, a single NN-based online PI algorithm is developed for the CT system, which is disturbed nonlinear ZSG. With plenty of online data, the Hamilton–Jacobi–Isaacs equation can be solved without complete dynamics. Then by the least-squares method, we can obtain the NN weights. Moreover, in the process of dealing with the undisturbed system, we find the way that obtains NN weights in this paper is equal to the way that obtains the optimal solution by the Gauss–Newton method. Based on the convergence of the Gauss–Newton method, we can efficiently obtain the optimal controller for the undisturbed system by utilizing online data. After getting the controller of the undisturbed system, it is time to take disturbance into consideration, so that we design a robust control pair to overcome the disturbance. In order to demonstrate the effectiveness of this algorithm, we design a set of simulations. The results verify that we can solve the disturbed nonlinear ZSG by this algorithm. [ABSTRACT FROM AUTHOR]

Common spatial pattern (CSP) is a classic method commonly used in multichannel electroencephalogram (EEG) signal processing, which aims to extract effective features for binary classification by solving spatial filters that maximize the ratio of filtered dispersion between two classes. The aim of this paper is to improve the performance of the conventional CSP method, which will be badly influenced by noises. The recently proposed quantized minimum error entropy (QMEE) criterion is applied to structure a new objective function instead of the ${L} _{2}$ -norm in the conventional CSP. Quantization is utilized to reduce the computational complexity. The new objective function is optimized by a gradient-based iterative algorithm. The desirable performance of the QMEE-based CSP method, namely CSP-QMEE, is demonstrated with a toy example and two real EEG datasets, including Dataset IIb of the brain–computer interfaces (BCIs) Competition IV (three channels) and Dataset IIIa of the BCI Competition III (60 channels). The new method can achieve satisfactory performance compared to existing methods on all datasets. The promising results in this paper suggest that the CSP-QMEE may become a powerful tool for BCIs. [ABSTRACT FROM AUTHOR]

The interpolation based algebraic soft decoding yields a high decoding performance for Reed-Solomon (RS) codes with a polynomial-time complexity. Its computationally expensive interpolation can be facilitated using the module structure. The desired Gröbner basis can be achieved by reducing the basis of a module. This paper proposes the low-complexity Chase (LCC) decoding algorithm using this module basis reduction (BR) interpolation technique, namely the LCC-BR algorithm. By identifying $\eta $ unreliable symbols, $2^\eta $ decoding test-vectors will be formulated. The LCC-BR algorithm first constructs a common basis which will be shared by the decoding of all test-vectors. This eliminates the redundant computation in decoding each test-vector, resulting in a lower decoding complexity and latency. This paper further proposes the progressive LCC-BR algorithm that decodes the test-vectors sequentially and terminates once the maximum-likelihood decision decoding outcome is reached. Exploiting the difference between the adjacent test-vectors, this progressive decoding is realized without any additional memory cost. Complexity analysis shows that the LCC-BR algorithm yields a lower complexity and latency, especially for high rate codes, which will be validated by the numerical results. [ABSTRACT FROM AUTHOR]

In this paper, we investigate the unmanned aerial vehicle (UAV)-aided simultaneous uplink and downlink transmission networks, where one UAV acting as a disseminator is connected to multiple access points (AP), and the other UAV acting as a base station (BS) collects data from numerous sensor nodes (SNs). The goal of this paper is to maximize the system throughput by jointly optimizing the 3D UAV trajectory, communication scheduling, and UAV-AP/SN transmit power. We first consider a special case where the UAV-BS and UAV-AP trajectories are pre-determined. Although the resulting problem is an integer and non-convex optimization problem, a globally optimal solution is obtained by applying the polyblock outer approximation (POA) method based on the problem’s hidden monotonic structure. Subsequently, for the general case considering the 3D UAV trajectory optimization, an efficient iterative algorithm is proposed to alternately optimize the divided sub-problems based on the successive convex approximation (SCA) technique. Numerical results demonstrate that the proposed design is able to achieve significant system throughput gain over the benchmarks. In addition, the SCA-based method can achieve nearly the same performance as the POA-based method with much lower computational complexity. [ABSTRACT FROM AUTHOR]

Consumer Electronics (CE) devices have started to support 360° videos in order to improve the perceived video quality by consumers. Higher compression in 360° videos not only lead to improved consumer perception, but also efficient energy and storage usage in CE devices. Consequently, efficient compression of such video content is becoming a critical design consideration of CE devices. To this end, this paper first proposes a residual weighting algorithm that utilizes the features of Weighted Craster Parabolic Projection Peak Signal-to-Noise Ratio (WCPPPSNR), to instigate the first stage of magnitude reduction of the residuals. The model parameters associated with the residual weighting algorithm are determined in the initial experimental stage. Next, the paper proposes a Quantization Parameter (QP) optimization technique which introduces the second stage of magnitude reduction for residuals with minimal impact on the overall video quality. The proposed method is tested on the Versatile Video Coding (VVC) test model with All-Intra configuration. In this context, the empirical results demonstrate that the proposed method improves the coding efficiency by 3.34% on average and outperforms the state-of-the-art techniques. [ABSTRACT FROM AUTHOR]

This paper derives the maximum achievable sum-rate and presents the optimal encoding/decoding framework for rate-diverse wireless network coding (RD-WNC) over broadband channels consisting of multiple parallel subchannels. RD-WNC applies to a communication scenario in which a base station wants to deliver two different messages with different rates to two users. The base station combines the two separate messages into one network-coded message and broadcasts the network-coded message to both users. Each user then extracts its desired message from the network-coded message by subtracting from it the other message, which we assume to be side information available to the user. Deriving the maximum achievable sum-rate for RD-WNC is challenging when the channel consists of multiple parallel subchannels with different channel coefficients (e.g., the subcarrier channels of OFDM systems), since apart from the rate allocation between the two users, optimal power allocation among multiple subchannels needs to be identified. The first contribution of this paper is a new “mountain-leveling” power allocation algorithm to achieve the maximum sum-rate. With the resulting power allocation, we can then achieve the corresponding optimal sum-rate by having a separate encoding/decoding mechanism for each subchannels, but doing so is cumbersome and complex when the number of subchannels is large. The second contribution of this paper is a practical encoding/decoding framework using only one encoder-decoder mechanism for all subchannels without sacrificing sum-rate optimality. We provide numerical results to corroborate our theoretical findings and to demonstrate the benefits of our encoding/decoding framework. [ABSTRACT FROM AUTHOR]

Autonomous vehicles will generate data from the variety of sensors they employ to track the surrounding environment. This data is inherently valuable, as it gives algorithm designers the potential to leverage prior experience in order to improve driving performance over time. This paper uses the lens of autonomous racing to provide an example of how data from previous iterations of driving can be used to improve quantitative metrics of performance. Two complementary algorithms are demonstrated in this paper. The first algorithm uses iterative learning control (ILC) to simultaneously improve lateral and longitudinal tracking of the desired racing trajectory over multiple laps, while the second algorithm is focused on altering the trajectory itself using a search method. When driven experimentally at the limits of handling, the result is a reduction in lap time of nearly 1.4 seconds, a major improvement. [ABSTRACT FROM AUTHOR]

Vehicular ad hoc networks (VANETs) are wireless self-organizing networks, whose communication is conducted through open wireless channels, thus making it vulnerable to various attacks. It is therefore necessary to employ encryption technology to ensure secure communication. In view of the foregoing, key agreement techniques are introduced to VANET communications. The group key agreement (GKA) protocol allows a group of participants to establish a public session key for a secure communication channel over an insecure network. The traditional GKA protocol is inefficient, however, and consumes considerable amounts of resources. With the aim of resolving problems related to information security and privacy preservation in VANETs, this paper proposes a full session key agreement scheme based on chaos mapping. In this paper, the first phase describes the key agreement between the fog server and group administrator; the second phase describes the group key agreement for vehicle nodes in the group where the vehicle can only communicate with vehicles having the same group key without the aid of a trusted key center or centralized key distributor. The proposed scheme is based on Chebyshev chaotic mapping algorithm, in which a chaotic map is utilized to provide a one-way hash; Chebyshev polynomial is also employed to establish a public multi-party key; it avoids the modular multiplication index or scalar multiplication on the elliptic curve. The proposed scheme does not only satisfy the security requirements in VANETs but also performs detailed analysis. [ABSTRACT FROM AUTHOR]

The Ultra-short baseline (USBL) positioning system has important application in the positioning of underwater vehicles. The installation error angle of the USBL positioning system has an important influence on the positioning accuracy of USBL system. The traditional calibration methods have limited estimation accuracy for installation error angles and have high route requirements. To solve the above problems, a calibration method of installation error angle based on attitude determination is proposed in this paper. When strapdown inertial navigation system (SINS) and USBL are fixed together in the application process, the installation error angle of USBL is fixed and unchanged. Then the calibration of installation error angle can be accomplished with the idea of attitude determination. The vector observation model based on the installation error angle matrix is established first. Observation vectors are obtained by the relative position of transponders in the USBL coordinate frame. The reference vector is calculated by position of transponder, position and attitude of SINS and lever arm between SINS and USBL. By constructing the observation vectors and the reference vectors, the proposed method can calibrate the installation error angle of SINS and USBL in real time. The advantages of the proposed method are that it has no specific requirements for the calibration route and can calibrate the installation error angle in real time with high accuracy. In order to verify the performance of the proposed algorithm, simulation experiment and field experiment are carried out in this paper. The results of simulation experiment and field experiment show that the proposed method can give the estimated installation error angle of USBL in real time, and the estimated result is the best among several methods. The proposed method can not only achieve the calibration of the installation error angle in circular trajectory, but also in straight trajectory. [ABSTRACT FROM AUTHOR]

This paper considers the problem of secure parameter estimation when an estimation algorithm is prone to causative attacks. Causative attacks, in general, target decision-making algorithms (e.g., inference or learning algorithm) to alter their decisions in specific scenarios (e.g., distort parameter estimates for specific ranges of the parameter of interest). Such attacks influence the decisions via tampering with the mechanisms through which an algorithm acquires the statistical model of the population about which it aims to form a decision. Such attacks are viable, for instance, by contaminating the historical or training data, or by compromising an expert who provides the statistical model. In the presence of causative attacks, inference algorithms operate under a distorted statistical model for the data samples. This paper introduces a notion of secure parameter estimation and formalizes a framework under which secure estimation can be formulated and analyzed. The central premise underlying the secure estimation framework is that forming secure estimates introduces a new dimension to the estimation objective, pertaining to detecting attacks and isolating the true model. Since detection and isolation decisions themselves are imperfect, their inclusion induces an inherent coupling between the desired secure estimation objective and the auxiliary detection and isolation decisions that need to be formed in conjunction with the estimates. This paper establishes the fundamental interplay among these decisions, and characterizes the general decision rules in closed-forms for any desired estimation cost function. Furthermore, to circumvent the computational complexity associated with growing parameter dimension or attack complexity, a scalable estimation algorithm is provided, which is shown to enjoy certain optimality guarantees. Finally, the theory developed is applied to secure parameter estimation in sensor networks. [ABSTRACT FROM AUTHOR]

Graph query autocompletion (gQAC) generates a small list of ranked query suggestions during the graph query formulation process in a visual environment. The current state-of-the-art of gQAC provides suggestions that are formed by adding subgraph increments to arbitrary places of an existing (partial) user query. However, according to the research results on human-computer interaction (HCI), humans can only interact with a small number of recent software artifacts in hand. Hence, many of such suggestions could be irrelevant. In this paper, we present the GFocus framework that exploits a novel notion of user focus of graph query formulation (or simply focus). Intuitively, the focus is the subgraph that a user is working on. We formulate locality principles inspired by the HCI research to automatically identify and maintain the focus. We propose novel monotone submodular ranking functions for generating popular and comprehensive query suggestions only at the focus. In particular, the query suggestions of GFocus have high result counts (when they are used as queries) and maximally cover the possible suggestions at the focus. We propose efficient algorithms and an index for ranking the suggestions. Our results show that GFocus saves 12-32 percent more mouse clicks and is 35× more efficient than the state-of-the-art competitor. [ABSTRACT FROM AUTHOR]

Dual Coordinate Descent (DCD) is one of the most popular optimization methods. The parallelization of DCD is difficult, as DCD is sequential in nature. As such, simultaneously running multiple DCD threads on batches of data elements causes result inaccuracy and slow convergence, due to the concurrent updates of multiple coordinates. Some parallelization methods adopt separable approximate functions that depend on the degree of parallelism. Such dependencies result in both poor scalability and slow-convergence. To address these challenges, in this paper we present a new parallel primal-dual algorithm for DCD, called PPD. In PPD, the block data distribution is utilized to obtain a new approximate function that is independent from the parallelism. Moreover, PPD is designed with a novel primal-dual acceleration scheme to approach the optimal solution closely and quickly. We demonstrate the advantages of PPD in terms of scalability and efficiency through experiments. [ABSTRACT FROM AUTHOR]

Dictionary learning has achieved remarkable success on a wide range of machine learning-based applications. In this paper, a locality-adaptive structured dictionary learning (LASDL) algorithm for cross-domain recognition is proposed. In the LASDL, a projective structured double reconstruction strategy is developed to train class-oriented sub-dictionaries from the specific classes of cross-domain samples. The strategy benefits to make full advantage of the discriminative information of cross-domain data and bridge the distribution divergence between two different domains. Meanwhile, an adaptive geometrical structure preserving function is designed to not only preserve the local manifold structures spanned by the representation coefficient spaces of the source and target domains, but also impose a constraint that the coefficients should keep closer to their class centers, which is propitious to reduce the distribution divergence and make the representation more accurate. With the structured linear coding technique, the final cross-domain recognition can be efficiently performed by determining class-specific reconstruction error. The optimization of the proposed LASDL model can be efficiently solved by simple least square method and alternating direction method of multipliers (ADMM) algorithm. Extensive experimental results validate the superiority of the proposed algorithm in contrast to other state-of-the-art predecessors. [ABSTRACT FROM AUTHOR]

Network partition in complex power networks is essential for the var-voltage control. Traditional partition methods such as Ward method are applied in practical power networks, but they are unable to evaluate the quality of partition results. Moreover, they lack efficiency when dealing with large-scale networks. Since complex operation characteristics and topology have emerged in recent power systems, the power grid partition requires higher efficiency and quality. Therefore, this paper proposes a fast network partition method with a balanced-depth-based community detection algorithm. Its aim is to significantly improve the efficiency of partition while maintaining high quality of partition, with which the inter-zone coupling is minimized while the intra-zone coupling is maximized. In the meantime, a surrogate-optimization-based selection algorithm is proposed to select the zonal pilot bus, based on which the secondary voltage control method is used to evaluate the quality of partition. Results from four case studies conducted in various power networks with different sizes, as compared to other partition methods, validate the high efficiency and high quality of the proposed power grid partition approach. [ABSTRACT FROM AUTHOR]

Addressing non-convexity plays a fundamental role in solving the optimal electricity-gas flow models. In this paper, an improved spatial branch-and-bound algorithm is proposed to solve the non-convex problem, which is formulated as a mixed-integer bilinear programming, for its exact solution. The core of the algorithm is to divide the non-convex model into convex and small sub-models by branching on specific continuous variables, so that the non-convex problem can be equivalent to a rooted tree for exploration. The exactness of the algorithm is guaranteed by the same criterion as the classical branch-and-bound algorithm. To alleviate the computational burden, a novel two-stage spatial branching strategy is developed to improve the effectiveness and efficiency of the branching operations. The performance of the proposed algorithm is verified on two integrated electricity-gas systems with different sizes. Numerical results demonstrate that our method achieves a balance among feasibility, optimality, and efficiency. The comparison with another 6 convexification-based methods, 3 state-of-the-art non-convex optimization solvers, and 2 spatial branch-and-bound algorithms with classical branching rules further shows the superiority of our algorithm. [ABSTRACT FROM AUTHOR]

Security-constrained unit commitment (SCUC) model is used for power system day-ahead scheduling. However, current SCUC model uses a static network to deliver power and meet demand optimally. A dynamic network can provide a lower optimal cost and alleviate network congestion. However, due to the computational complexity and the lack of effective algorithms, network reconfiguration has not been included in the SCUC model yet. This paper presents a novel approach to handle the computational complexity in security-constrained unit commitment (SCUC) with corrective network reconfiguration (CNR) while considering the scalability through accelerated-decomposition approach with fast screening non-critical sub-problems of SCUC-CNR. The proposed approach provides substantial computational benefits and is also applicable to SCUC. Simulation results on the IEEE 24-bus system show that the proposed methods are substantially faster without the loss in solution quality while the scalability benefits are demonstrated using larger cases: the IEEE 73-bus system, IEEE 118-bus system and Polish system. [ABSTRACT FROM AUTHOR]

This paper focuses on improving indoor Wi-Fi localization by mitigating the effect of fluctuation of received signal strength indication (RSSI). The RSSI data collected at each reference point is first transformed through translation and scaling. The BP (Back Propagation) neural network is then used to construct the ranging model using the transformed RSSI to determine the distances between the target point and each reference point. A genetic algorithm (GA) is developed to optimize the initial values of weights and biases of the BP neural network. For convenience, our proposed ranging model is denoted as GTBPD. A new localization algorithm is then proposed, which uses the GTBPD model and the sequential quadratic programming (SQP, an iterative nonlinear optimization algorithm), and the algorithm is denoted as GTBPD-LSQP for simplicity. Experiments were conducted in three areas of two different teaching buildings with complex environments. The performance of the proposed GTBPD-LSQP algorithm is evaluated and compared with four existing algorithms. The experimental results show that our proposed GTBPD-LSQP algorithm achieves significantly higher location accuracy than the four existing algorithms. [ABSTRACT FROM AUTHOR]

We consider a class of nonconvex regularized optimization problems, which appear frequently in machine learning and data processing. Due to the structure of the problems, the iteratively reweighted algorithm was developed and applied to the consensus optimization. In this paper, we propose the acceleration of this scheme by adding an inertial term in each iteration. The proposed algorithms inherit the advantages of classical decentralized algorithms: they can be implemented over a connected network, in which the agents communicate with their neighbors and perform local computations. We also employ the diminishing stepsizes technique for the iteratively reweighted algorithm and consider its acceleration. In specific cases, our algorithms reduce to existing decentralized schemes and also indicate novel ones. Mathematically, we prove the convergence for both algorithms with several assumptions on the objective functions. With Kurdyka-Łojasiewicz property, convergence rates can be derived for constant stepsize case. Numerical results demonstrate the efficiency of the algorithms. [ABSTRACT FROM AUTHOR]

Range-based positioning using wireless signal has gained remarkable attention in past decades. Accurately extracting the distance information, i.e., estimating parameters of individual multipath, is of interest. It has been shown that diffuse multipath component (DMC) in wireless propagation channel has significant influence on channel estimation and, thus, the ranging performance. In addition to specular component (SC), DMC should be considered in order to improve the estimated accuracy of channel paths’ parameters and, thus, the ranging performance. In this paper, we extend the quasi-maximum likelihood space-alternating generalized expectation-maximization (SAGE) algorithm by incorporating an autoregressive moving average (ARMA) filter to estimate the channel parameters under the presence of DMC. The parameters of both DMC and SC are estimated in an iterative approach, where the DMC is assumed as colored noise and the ARMA-filter is used to estimate the contributions from DMC. The validation of the algorithm based on measured data shows that both SC and DMC can be accurately estimated by the proposed approach. A comparison with standard SAGE and AR-SAGE is conducted, where the results reveal that the proposed method outperforms other two approaches in terms of ranging accuracy. [ABSTRACT FROM AUTHOR]

In this paper, an intelligent reflecting surface (IRS) is deployed to assist the terahertz (THz) communications. The sum-rate of user equipments (UEs) is maximized while guaranteeing the rate requirement of each UE. A block coordinate searching (BCS) algorithm is proposed to jointly optimize the IRS’s coordinates, phase shifts, THz sub-bands allocation and power control. Specifically, the relaxation with penalties based (RPB) algorithm is developed to obtain feasible coordinates of the IRS and guarantee the monotonicity of objective value. In addition, the IRS phase shifts are formulated as closed-form expressions with introduced pricing factors. Simulation results show that the proposed scheme can significantly enhance system performance. [ABSTRACT FROM AUTHOR]

In this paper, we consider a computation offloading problem in a three-tier network consisting of multiple mobile users (MUs), multiple edge clouds, and a central cloud. On this basis, we formulate a system Energy Time Cost ($ETC$) minimization problem by jointly optimizing the resource allocation, mobile-edge matching decision, and offloading decision. Due to the difficulty of directly solving the formulated problem, we decompose it and propose two offloading algorithms, namely Gale-Shapley based Minimum/Sequential Offloading Algorithm (GS-MOA/GS-SOA), to optimize offloading decisions by minimizing the system $ETC$ , in which the mobile-edge matching strategies based on the proposed Gale-Shapley based Mobile-Edge mAtching aLgorithm (GS-MEAL) and resource allocations are optimized iteratively. The simulations show the effectiveness of our proposed algorithm. [ABSTRACT FROM AUTHOR]

In this paper, we propose an adaptive vehicle clustering algorithm based on fuzzy C-means algorithm, which aims at minimizing power consumption of the vehicles. Specifically, the proposed algorithm firstly dynamically allocates the computing resources of each virtual machine in the vehicle, according to the popularity of different virtualized network functions. The optimal clustering number to minimize the total energy consumption of vehicles is determined using the fuzzy C-means algorithm and the clustering head is selected based on vehicles moving direction, weighted mobility, and entropy. Simulation results are provided to confirm that the proposed algorithm can decrease the power consumption of vehicles while satisfying the vehicle delay requirement. [ABSTRACT FROM AUTHOR]

Infrared and visible image fusion (IVIF) expects to obtain images that retain thermal radiation information from infrared images and texture details from visible images. In this paper, a model-based convolutional neural network (CNN) model, referred to as Algorithm Unrolling Image Fusion (AUIF), is proposed to overcome the shortcomings of traditional CNN-based IVIF models. The proposed AUIF model starts with the iterative formulas of two traditional optimization models, which are established to accomplish two-scale decomposition, i.e., separating low-frequency base information and high-frequency detail information from source images. Then the algorithm unrolling is implemented where each iteration is mapped to a CNN layer and each optimization model is transformed into a trainable neural network. Compared with the general network architectures, the proposed framework combines the model-based prior information and is designed more reasonably. After the unrolling operation, our model contains two decomposers (encoders) and an additional reconstructor (decoder). In the training phase, this network is trained to reconstruct the input image. While in the test phase, the base (or detail) decomposed feature maps of infrared/visible images are merged respectively by an extra fusion layer, and then the decoder outputs the fusion image. Qualitative and quantitative comparisons demonstrate the superiority of our model, which can robustly generate fusion images containing highlight targets and legible details, exceeding the state-of-the-art methods. Furthermore, our network has fewer weights and faster speed. [ABSTRACT FROM AUTHOR]

Due to multi-layer encoding and Inter-layer prediction, Scalable High Efficiency Video Coding (SHVC) has extremely high coding complexity. It is very crucial to improve its coding speed so as to promote widespread and cost-effective SHVC applications. In this paper, we propose a new probability-based fast Intra prediction algorithm for spatial SHVC. More specifically, first, we integrate depth probabilities with textural based all-zero blocks and all-nonzero blocks through Lagrange Interpolation Polynomial (LIP) to derive thresholds to early skip unlikely depths and early terminate depth selection. Second, to early skip Intra mode prediction, we combine mode probabilities with Jarque-Bera test through LIP to test the residual coefficients of Inter-layer reference (ILR) mode. Third, we adopt the difference of Hadamard Costs (HCs) of horizontal, vertical and diagonal directional modes to predict candidate directional modes (DMs), and then exploit both the percentages of gradient amplitudes and HCs for DM early termination. Experimental results demonstrate that the proposed algorithm can achieve a speed up gain of more than 61% with 0.03% decrease in Bjøntegaard Delta Bit Rate on average. [ABSTRACT FROM AUTHOR]