Search

Based on the comparisons of several inverter configurations in the aspects of efficiency, response, volume, current distortion, and price, in this article, we present a feasible three-phase four-wire (3Φ4W) grid-connected hybrid-frequency parallel inverter system (HbFPIS) with ripple compensation to achieve low current distortion and fast response. An HbFPIS consists of a low-frequency-high-power inverter (LFHPI) and a high-frequency-low-power inverter (HFLPI) connected in parallel. An LFHPI design results in higher power output with lower frequency (LF) switching devices, such as insulated gate bipolar transistors (IGBTs) being more cost-effective. An HFLPI design can reduce switching loss by lowering the power requirement of high-frequency (HF) switching devices while increasing dynamic response. With the direct digital control and ripple compensation, LF current ripples are attenuated by the HFLPI to a smaller level, remaining mainly HF current ripples and, thus, resulting in smaller filter size and weight. The design of an HbFPIS ensures that the system has high power output with cost-effective devices, fast response, and smaller output filters. Ripple attenuation, current tracking capability, and inverter stability are analyzed in the article. Low current distortion and fast current tracking performance are validated by the 300-kW simulated and the 10-kW experimental results of a 3Φ4W HbFPIS in grid-connected and active power filter modes. [ABSTRACT FROM AUTHOR]

In this study, we successfully deposited c-axis-oriented aluminum nitride piezoelectric films via low-temperature dc sputtering method. Based on the X-ray diffraction (XRD) and TEM analyses, deposited films with a c-axis monocrystal were identified. The effective d33,ƒ value of the aluminum nitride (AlN) films is 5.92 pC/N, which is better than most of the reported data using dc sputtering processing. Using ANSYS software, we simulated and designed MEMS accelerometers based on AlN films. Furthermore, we successfully fabricated MEMS accelerometers. The sensitivity of the MEMS accelerometer is 1.49 mV/g, and the resonance frequency is 7.2 kHz. The MEMS accelerometer was combined with a sensing circuit constituting a module. The sensitivity of the module increases approximately tenfold. Finally, the vibration of spindles was successfully detected using the designed module. [ABSTRACT FROM AUTHOR]

This paper presents a sinusoidal pulsewidth modulation (SPWM) based direct digital control with average-voltage model (AVM) and division–summation process for paralleled three-phase three-wire (3φ3W) grid-connected converters to reduce circulating currents. With the direct digital control, plant of each single-phase converter can be derived directly, and a controller is then designed to cover the variation effects of filter inductance and grid voltage. Based on SPWM and AVM over a switching cycle, each 3φ3W converter can be decomposed into three single-phase converters and each converter is controlled individually to track its sinusoidal reference current tightly, reducing circulating currents significantly. Equal current sharing is therefore also achieved. The control laws for achieving grid connection are derived in detail. In the design and implementation, the inductances corresponding to various inductor currents are measured offline and stored in the controller for scheduling loop gain cycle by cycle. Experimental and simulated results from a three-converter system confirm the analysis and discussion of the proposed control approaches. [ABSTRACT FROM AUTHOR]

Soft magnetic powder cores with their high saturation flux density and low core loss are excellent alternatives for filter inductors in inverter-based applications. However, their nonlinear current-dependent inductance characteristics pose a challenge for control of grid-connected inverter with LCL filter. In this paper, the variable inductance conundrum is discussed and a modified direct digital control method based on a variable-structure inductance estimation model that takes into consideration wide nonlinear variation in both inverter- and grid-side inductances is proposed. The proposed method is shown to have better grid-voltage harmonic rejection and improved stability margins. However, investigation of stability which is conventionally based on nominal values of filter inductors cannot predict instabilities over the entire range of inductance variation. Hence, a parametric approach to conventional stability methods with a parameter space defined by variation in actual and estimated inductance is explored in this paper. The effect of line impedance on stability is also investigated with impedance-based stability criterion by considering line inductance as an additional dimension in the parameter space. A pattern in stability margins is observed due to inductance variation, with inductance at its minimum being most vulnerable to instability. Experimental results measured from a 5 kW single-phase grid-connected inverter with various LCL filters have verified the feasibility of the proposed control method. The experimental results also match the analytical results with reasonable accuracy. [ABSTRACT FROM AUTHOR]

In this letter, we compared the structural and sensing properties of CeTiO3 and Ce2TiO5 sensing films for electrolyte–insulator–semiconductor (EIS) pH sensors. The structural behavior of these sensing films was characterized by Auger electron spectroscopy, atomic force microscopy, and X-ray photoelectron spectroscopy. In comparison with CeTiO3 sensing film, the EIS sensor using a Ce2TiO5 sensing film exhibited better sensing performance including higher sensitivity (68.35 mV/pH), lower hysteresis voltage (0.9 mV), and smaller drift rate (0.19 mV/h), presumably suggesting this film possessing a high fraction of Ce3+ and a rough surface. [ABSTRACT FROM PUBLISHER]