Search

Ambient ionization mass spectrometry (AIMS) has been developing explosively since its first debut. The ionization process was hence able to be achieved under atmospheric pressure, facilitating on-site field analysis in a variety of areas, such as clinical diagnosis, metabolic phenotyping, and surface analysis. As part of the ambitious goal of making MS a general device that can be used in everyday life, lots of efforts have been paid to miniaturize the ionization source. This review discusses avant-garde sources that could be entirely hand-held without any accessories. The structure and applications of the devices are described in detail as well. They could be expediently used in real-time and on-site analysis, presenting a great future potential for the routinizing of MS., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH, DE part of Springer Nature.)

A sharp metal needle used as the ionization emitter in conventional atmospheric pressure chemical ionization (APCI) mass spectrometry (MS) is usually required for analyte ionization through corona discharge (i.e., gas discharge). Nevertheless, we herein demonstrate that an insulating fiber (tip diameter: 10-60 µm; length: ~ 1 cm) made of glass or bamboo can function as an APCI-like ionization emitter. Although no direct electric contact is made on the fiber, the ionization of volatiles and semi-volatiles occurs when the fiber is placed close (~ 1 mm) to the inlet of the mass spectrometer. No analyte ion signals can be observed without placing the insulating fiber in front of the mass spectrometer. The generation of ion species mainly relies on the electric field provided by the mass spectrometer. Presumably, owing to the high electric field provided by the mass spectrometer, the dielectric breakdown voltages of gas molecules in the air and the fiber are overcome, leading to the ionization of analytes in gas phase. In addition, the insulating fiber can function as a holder for sample solutions. Electrospray ionization-like processes derived from polar analytes such as amino acids, peptides, and proteins can readily occur when the insulating fiber deposited with a sample droplet is placed close to the inlet of the mass spectrometer. The feasibility of using the current approach for the detection of nonpolar and polar analytes from complex fetal bovine serum samples without tedious sample pretreatment is demonstrated in this work. The main advantage of using the suggested fiber is that the fiber can be used as the sampling probe to pick up samples and placed in front of a mass spectrometer for direct MS analysis. The application of using a robust, insulating, and disposable probe to pick up samples from real samples such as onion, honey, and pork samples followed by direct MS analysis is also demonstrated., (© 2022. Springer-Verlag GmbH Germany, part of Springer Nature.)

Nowadays, due to environmental pollution and natural energy consumption caused by waste paper, many researches are being conducted on the reuse of printed-paper. To recycle the paper, de-inking has to be performed. In this article, in order to reduce the use of the commonly used de-inking chemicals, the effect of an atmospheric pressure helium plasma treatment on the de-inking enhancement of printed-paper is studied. Through colorimeter and UV-visible spectrometer measurements the plasma treatment is shown to speed up the de-inking. While SEM observations and FTIR measurements suggest that the paper quality is retained upon plasma treatment, the increase of surface hydrophilicity measured by water contact angle measurements, compared to non-treated paper, is believed to enhance the fiber swelling of the paper and lead to a faster ink removal. [ABSTRACT FROM AUTHOR]

• Nanogel particles are deposited onto carbon paper by a spray coating method. • CO 2 adsorption-desorption experiments are performed in a milli-channel reactor. • The adsorbent exhibits fast CO 2 adsorption rate and desorption rate. • The adsorbent presents good stability under wet conditions. In this work, we report a proof-of-concept study on CO 2 adsorbents synthesized by a thermally initiated free-radical copolymerization and then coated onto carbon paper and poly tetra fluoroethylene via a spray coating approach. A milli-channel reactor was employed to support the obtained materials for efficient CO 2 capture with wet conditions, short cooling and heating cycles (303–348 K). CO 2 uptake and release performance of the materials were measured and compared with that of the polyamine-based materials prepared by other methods. CO 2 adsorption and desorption kinetics can be greatly enhanced when using the spray coating approach, especially for carbon paper as supporter. The CO 2 adsorption capacity of the spray-coated carbon paper reaches 80% of its maximum value in only 4.37 ± 0.7 min. Moreover, its adsorption rate (114.6 mg/(g∙min) at 303 K) and desorption rate (239.9 mg/(g∙min) at 348 K) were 81.2% and 81.5% higher than those of the polyamine-impregnated carbon paper, respectively (12% CO 2 at atmospheric pressure). Their largest increases of 71% and 67% were achieved by adjusting the concentration of polyamine nanogel particles deposited on the carbon paper surface. The prepared material also presents stable recyclability over 10 wet adsorption–desorption cycles and the aging experiments. The results obtained in this study indicate that the synthesized materials can serve as promising energy-efficient solid adsorbents for CO 2 capture. [ABSTRACT FROM AUTHOR]

A study of plasma treatment of clay-coated paper is presented. The wettability of the paper surface before and after the plasma treatment was determined by measuring the water contact angle and surface free energy. The appearance of the surface-functional groups was determined by using high-resolution X-ray photoelectron spectroscopy, while changes in the surface morphology were monitored by scanning electron microscopy. Already after 0.25 s of the plasma treatment, the paper surface improved its wettability. The X-ray photoelectron spectroscopy analyses showed a gradual increase of oxygen-rich functional groups on the surface while scanning electron microscopy analyses did not show a significant modification of the morphology and no alternation of the surface structure after the plasma treatment. [ABSTRACT FROM AUTHOR]

Deposition of transparent oxide films at atmosphere pressure onto polymeric substrates at room temperature is a technique gaining rapid acceptance. These films can be used for numerous applications such as antiscratch and water permeation barrier coatings. In this paper, a \sim 1.4 - \mu \text{m} SiOx layer has been deposited on polypropylene-coated paper at atmosphere pressure with a filamentary dielectric barrier discharge (DBD). The DBD linear discharge was driven by a 30-kHz power supply. Scanning electron microscope, X-ray photoelectron spectroscopy, and attenuated total reflection-Fourier transform infrared spectroscopy were used to characterize the deposited film. The deposited thin film decreased water permeation through the paper by \sim 15$ %. [ABSTRACT FROM PUBLISHER]

Siloxanes have been found widespread usages in our daily lives, but the knowledge on their migration, transformation and toxicity is still limited. Herein we explored the feasibility of using one-sided silica coated paper as filter membrane to capture siloxanes in the outdoor air, followed by direct mass spectrometric analysis. In contrast to mostly utilized fiber membrane, silica coated paper not only exhibited a higher selective sampling efficiency to three siloxanes with structures of H–[Si(CH 3) 2 –O] 7-9 -NH 2 from air, but also possessed a high tolerance to organic solvent during mass spectrometric analysis. Due to the above features, the analysis sensitivity of those siloxanes with silica coated paper has been improved 3.1–134.8 folds in contrast to those with commercial filter membrane. Furthermore, we monitored variation in the levels of those siloxanes for a period of one month, and found that a close association (R2 = 0.7924–0.9559) existed between their contents and climate parameters (e.g., temperature, weather, atmospheric pressure, humidity, wind direction and wind speed) as well as sampling volume. These knowledge provides a facile and effective methodology to both high-efficient sampling siloxanes and environmental assessment of siloxanes according to climate parameters. [Display omitted] • Develop a facile strategy for fabricating one-sided sorbent coated paper substrate. • Exploit silica coated paper for sampling and analyzing siloxanes in outdoor air. • Observe superior capacity of silica coated paper over conventional filter membrane. • Construct a relationship between siloxane contents in air and climate parameters. [ABSTRACT FROM AUTHOR]

Paper-based relics, which are an important part of cultural heritage worldwide, are at risk of imminent damage from various environmental sources. To protect them, the atmospheric pressure plasma polymerization of hexamethyldisiloxane (HMDSO) precursor has been explored on paper-based relics in situ. The macro and micro images taken during this process suggest that the in situ plasma treatment does not change the macro morphology and the micro structure of the treated paper-based relic samples. On the other hand, plasma treatment causes the polymerization of the HMDSO which then produces nanoparticles deposited onto the paper-based relics. These nanoparticles provide good waterproof properties with large static water contact angles and smaller rolling angles, which protect the paper-based relics from water penetration. Moreover, since the nanoparticles are deposited onto the fibers, waterproof fastness is ensured. Also, the examined mechanical properties of the treated and untreated paper-based relics indicate that the atmospheric pressure plasma treatment does not affect the strength of the paper very much. The results in this study show that atmospheric pressure plasma treatment with the use of HMDSO precursor is a good method to preserve paper-based relics. [ABSTRACT FROM AUTHOR]

Different amounts of a stable aqueous TiO2 hydrosol were used to fabricate paper sheets having photocatalytic activity. The TiO2 hydrosol was prepared in aqueous medium using titanium butoxide as precursor and acetic acid as catalyst for the hydrolysis of titanium butoxide. An aging process at room temperature and atmospheric pressure was finally applied to obtain crystalline anatase TiO2 hydrosol. The effects of different TiO2 hydrosol loadings on the mechanical strength and barrier properties of modified paper sheets were investigated in detail. The photocatalytic behavior of TiO2-modified paper sheets was investigated as well using methylene blue (MB) as target pollutant. [ABSTRACT FROM AUTHOR]

This study's aim is a comparison of the plasma-induced effects on polymers exposed in helium and argon gaseous environments in a pulsed dielectric barrier discharge at atmospheric pressure. Cellulose-based and synthetic polymers are tested with regard to a range of parameters, such as wettability, adhesion, surface energy and polarity, the oxygen amount in their structure, and surface morphology. The surface properties are analyzed by contact angle measurements, X-ray photoelectron spectroscopy, and scanning electron microscopy images. The results point to the efficient and remarkably stable modifications of the plasma-exposed surfaces, such as their enhanced adhesion, surface energy, and oxygen incorporation. Additionally, plasma provides significant oxygen uptake in cellulose-based materials that bear already prior to treatment a high amount of oxygen in their structure. The comparison between the properties of the non-permeable, homogeneous, smooth-surface synthetic polymer and those of the loosely packed, porous, heterogeneous cellulose-based polymers points to the different rates of plasma-induced modification, whereby a progressive alteration of cellulosic surface properties over much larger ranges of exposure durations is noted. Present experimental conditions ensure mild treatments on such sensitive material, such as paper, and this is without alterations of the surface morphology and the physical degradation of the material over a large range of treatment duration. [ABSTRACT FROM AUTHOR]

For release-liner preparation, coating stabilization of the silicone layer on base paper often requires pre- and post-treatment. In this study, we used atmospheric pressure diffuse coplanar surface barrier discharge in roll-to-roll configuration. The results of prepared coating showed that the A4 size clay-coated paper sprayed with silicone oil (0.25–0.50 mL) gradually decreased the tape peeling force (180°) with prolonged and repeated air plasma post-treatment. Best results showing increased hydrophobicity and significantly enhanced release factor of the coating were obtained after the plasma treatment in a nitrogen atmosphere. The silicone coating on the clay-coated paper reduced the reference release force from 5.5 N/cm to less than 1.5 N/cm after the repeated silicone spraying and short nitrogen plasma post-treatment. The results of X-ray photoelectron spectroscopy and scanning electron microscopy indicate silicone curing by plasma post-treatment and pore-closing of base paper without changes of the bulk material. The aging test lasting 3 months revealed the stability of the prepared coating. [ABSTRACT FROM AUTHOR]

Detailed characterization and classification of precipitation is an important task in atmospheric research. Line scanning 2-D-video disdrometer technique is well established for rain observations. The two orthogonal views taken of each hydrometeor passing the sensitive area of the instrument qualify this technique especially for detailed characterization of non symmetric solid hydrometeors. However, in case of solid precipitation problems related to the matching algorithm have to be considered and the user must be aware of the limited spacial resolution when size and shape descriptors are analyzed. This work has the aim of clarifying the potential of 2-D-video disdrometer technique in deriving size, velocity and shape parameters from single recorded pictures. The need of implementing a matching algorithm suitable for mixed and solid phase precipitation is highlighted as an essential step in data evaluation. For this purpose simple reproducible experiments with solid steel spheres and irregularly shaped styrofoam particles are conducted. Self-consistency of shape parameter measurements is tested in 40 cases of real snow fall. As result it was found, that reliable size and shape characterization with a relative standard deviation of less than 5% is only possible for particles larger than 1 mm. For particles between 0.5 and 1.0mm the relative standard deviation can grow up to 22% for the volume, 17% for size parameters and 14% for shape descriptors. Testing the adapted matching algorithm with a reproducible experiment with styrofoam particles a mismatch probability of less than 2.5% was found. For shape parameter measurements in case of real solid phase precipitation the 2DVD shows self-consistent behavior. [ABSTRACT FROM AUTHOR]

The paper explores the possibility of implementing an advanced photogrammetric technique, generally employed for satellite measurements, on airglow imager, a ground-based remote sensing instrument primarily used for upper atmospheric studies, measurements of clouds for the extraction of cloud motion vectors (CMVs). The major steps involved in the algorithm remain the same, including image processing for better visualization of target elements and noise removal, identification of target cloud, setting a proper search window for target cloud tracking, estimation of cloud height, and employing 2-D cross-correlation to estimate the CMVs. Nevertheless, the implementation strategy at each step differs from that of satellite, mainly to suit airglow imager measurements. For instance, climatology of horizontal winds at the measured site has been used to fix the search window for target cloud tracking. The cloud height is estimated very accurately, as required by the algorithm, using simultaneous collocated Lidar measurements. High-resolution, both in space and time (4 min), cloud imageries are employed to minimize the errors in retrieved CMVs. The derived winds are evaluated against MST radar-derived winds by considering it as a reference. A very good correspondence is seen between these two wind measurements, both showing similar wind variation. The agreement is also found to be good in the both zonal and meridional wind velocities with RMSEs< 2.4 ms-1. At the end, the strengths and limitations of the algorithm are discussed, with possible solutions, wherever required. [ABSTRACT FROM AUTHOR]

Copyright of Food Research & Development is the property of Food Research & Development Editorial Department and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This paper presents an experimental campaign conducted next to the Condoroma dam, in Perú, at 4075 m a.s.l. The tests carried out in this paper were conducted in a 21 m long channel located at the toe of Condoroma dam. The setup consisted of a series of standard profile spillways with a vertical upstream face of up to five different dimensionless heights (P/Hd) ranging from 0.5 to 2. The experimental results indicated that, the P/Hd ratio influences the discharge coefficients in Condoroma, and P/Hd ≥ 1 values are recommended for the design of the spillway profile. In addition, for all the P/Hd ratios studied, the discharge coefficients adjusted to the Condoroma altitude were lower than those reported by classical formulations used in conventional spillway designs. Finally, a generalized equation is proposed to estimate the discharge coefficient for standard spillways located in dams at similar elevations above sea level. [ABSTRACT FROM AUTHOR]

The external insulation strength of the power equipment sleeve in the substation and converter station will be reduced with the increase in altitude and atmosphere pollution. The weakness of external insulation seriously threatens the safe operation of electrical equipment. At present, there are few studies and conclusions that focus on the flashover characteristics of power equipment bushing in high-altitude polluted areas. Therefore, this paper takes the 220 kV voltage level bushing as the research object and studies the Alternating Current (AC) pollution flashover characteristics and lightning and switching impulse flashover characteristics at low pressure. The insulation configuration at high-altitude polluted areas is analyzed. Finally, the insulation configuration scheme, which is suitable for high-altitude polluted areas, is proposed. The results show that the AC pollution flashover voltages of the bushing decrease with the decrease in the atmospheric pressure and the increase in the salt density as a power exponent function. The impulse flashover voltages also decrease with the decrease in the atmospheric pressure as a power exponent function. The atmospheric pressure/pollution impact characteristic index is related to the type of voltage, the value of the atmospheric pressure, and the value of the salt density. The test bushing does not meet the insulation configuration requirements in some high-altitude polluted areas. Through the analysis and calculation of the test results, the bushing insulation configuration scheme in high-altitude polluted areas is proposed. The research results can provide a reference for the external insulation design of bushings in substations and converter stations in high-altitude polluted areas. [ABSTRACT FROM AUTHOR]

This paper presents an analytical approach to envisage a suitable operating pressure and investigate the effect of squeezed-film damping on the transient response of a micromirror of size 200 µm × 200 µm and a deflection of 2.5 µm for space-based multiobject spectroscopy. While most MEMS devices are vacuum packaged to achieve a high Q and fast switching, the same may not be true for applications that are prone to vibrations and shocks. At small pressures, the micromirror can produce undesired deflections and oscillations, and hence, a high-pressure operation becomes necessary to alleviate these effects. The operating pressure and its effect on the transient response of the micromirror are investigated by solving linearized Reynold's equation and dynamic equation of motion using the numerical iteration method. The result shows an overdamped response above 10 kPa pressure. At 101 kPa, the micromirror exhibits a switching and release time of 102 µs and 95 µs, respectively. The analytical results are very close to the FEM results with a deviation of 8%. The result shows that operating a micromirror at atmospheric pressure serves the dual purpose of dispensing away with the requirement of vacuum packaging and providing immunity from vibrations and oscillation. [ABSTRACT FROM AUTHOR]

This paper presents the results of studies on the transformation of geraniol (GA) in the presence of the natural mineral bentonite. The paper determines the influence of temperature, catalyst content, and reaction time on the course of the process. In order to determine the most favorable process conditions, the catalytic tests were carried out without solvent and under atmospheric pressure. Three functions were chosen to determine the most favorable process conditions: GA conversion and the selectivities of the main products: linalool – LO and beta-pinene – BP. In addition, the paper optimize GA transformation process based on response surface methodology (RSM). The impact of the most relevant process indicators was presented. For all factors of the method, their effects on all primary parameters were determined in the form of second-degree polynomials, and such process conditions were determined to achieve their maximum. [ABSTRACT FROM AUTHOR]

This paper deals with CFD analyses of the difference in the nature of the shock waves in supersonic flow under atmospheric pressure and pressure conditions at the boundary of continuum mechanics for electron microscopy. The first part describes the verification of the CFD analyses in combination with the experimental chamber results and the initial analyses using optical methods at low pressures on the boundary of continuum mechanics that were performed. The second part describes the analyses on an underexpanded nozzle performed to analyze the characteristics of normal shock waves in a pressure range from atmospheric pressure to pressures at the boundary of continuum mechanics. The results obtained by CFD modeling are prepared as a basis for the design of the planned experimental sensing of density gradients using optical methods, and for validation, the expected pressure and temperature courses from selected locations suitable for the placement of temperature and pressure sensors are prepared from the CFD analyses. [ABSTRACT FROM AUTHOR]

In the present paper, the use of programmable microprocessors to develop a computerized stand for the preparation of a mixture of flammable/toxic/explosive gases in order to obtain mixtures at concentrations in explosive range is presented. The operating principle of the stand is based on the mixing of two volumetric flows, controlled with the help of microprocessors, where gases are stored and circulated at atmospheric pressure through cylindrical injectors, driven by stepper motors so that the gas circuit does not require valves. The exit of the stand is a homogenization chamber, with agitator and sensor to confirm the desired concentration of the mixture. This automated stand eliminates mechanical, electric or pneumatic valves from the gas circuits, avoiding elements with high mechanical resistance suitable for high pressures/depressions, removing the possibility of the return of the gas flow, without sensitivity to sudden pressures variations. [ABSTRACT FROM AUTHOR]

The cause of the systematic daily march of barometric pressure in the tropics, notably the late morning and late evening peaks seen almost every day at all locations, was a puzzle that persisted through the nineteenth and much of the twentieth centuries. The efforts to explain the physics of the prominent 12-h solar tidal variation helped inspire some of the earliest developments in theoretical atmospheric dynamics and ultimately led in the 1960's to a satisfactory dynamical theory for the atmospheric tides. These important theoretical developments followed the observational discoveries, which date to the late 18th and early 19th centuries, of the surprising character of the barometric daily march and of its resolution into solar and lunar period cycles. These important, if simple, discoveries emerged primarily from the efforts of European scientists to systematically study the environment in remote areas of the globe. The two key figures in initially advancing the scientific community's understanding of the character of barometric tides were the great German polymath Alexander von Humboldt (1769–1859) and the French naturalist Robert de Lamanon (1752–1787), who each made their discoveries on their most famous and colorful scientific expeditions of their respective careers. This paper examines the history of the early observations of the barometric tide. [ABSTRACT FROM AUTHOR]

Atmospheric amines may play a crucial role in formation of new aerosol particles via nucleation with sulphuric acid. Recent studies have revealed that concentrations below 1 ppt can significantly promote nucleation of sulphuric acid particles. While sulphuric acid detection is relatively straightforward, no amine measurements to date have been able to reach the critical sub-ppt concentration range and atmospheric amine concentrations are in general poorly characterized. In this work we present a proof-of-concept of an instrument capable of detecting dimethyl amine (DMA) with concentrations even down to 8 ppq (parts per quadrillion, 0.008 ppt) for a 15 min integration time. Detection of ammonia and amines other than dimethyl amine is discussed. We also report results from the first ambient measurements performed in spring 2013 at a boreal forest site. While minute signals from some amines were observed, DMA concentration never exceeded the detection threshold of ambient measurements (20 ppq), suggesting that it is unlikely that nucleation at this location involves DMA. [ABSTRACT FROM AUTHOR]

Complex oceanic circulation and air--sea interaction make the eastern tropical Pacific Ocean (ETPO) a highly variable source of CO2 to the atmosphere. Although the scientific community have amassed 70 000 surface partial-pressure of carbon dioxide (pCO2) datapoints within the ETPO region over the past 25 years, the spatial and temporal resolution of this dataset is insufficient to fully quantify the seasonal to inter-annual variability of the region, a region where pCO2 has been observed to fluctuate by >300 µatm. Upwelling and rainfall events dominate the surface physical and chemical characteristics of the ETPO, with both yielding unique signatures in sea surface temperature and salinity. Thus, we explore the potential of using a statistical description of pCO2 within sea-surface salinity-temperature space. These SSS/SST relationships are based on in-situ SOCAT data collected within the ETPO. This statistical description is then applied to high resolution (0.25°) SMOS sea surface salinity and OSTIA sea surface temperature in order to compute regional pCO2. As a result, we are able to resolve pCO2 at sufficiently high resolution to elucidate the influence various physical processes have on the pCO2 of the surface ETPO. Normalised (to 2014) oceanic pCO2 between July 2010 and June 2014 within the entire ETPO was 41 µatm supersaturated with respect to 2014 atmospheric partial pressures. Values of pCO2 within the ETPO were found to be broadly split between southeast and a northwest regions. The north west, central and South Equatorial Current regions were supersaturated, with wintertime wind jet driven upwelling found to be the first order control on pCO2 values. This contrasts with the southeastern/Gulf of Panama region, where heavy rainfall combined with rapid stratification of the upper water-column act to dilute dissolved inorganic carbon, and yield pCO2 values under-saturated with respect to atmospheric partial pressures of CO2. [ABSTRACT FROM AUTHOR]

In remote sensing applications, such as differential optical absorption spectroscopy (DOAS), atmospheric scattering processes need to be considered. After inelastic scattering on N2 and O2 molecules, the scattered photons occur as additional intensity at a different wavelength, effectively leading to filling-in of both solar Fraunhofer lines and absorptions of atmospheric constituents. Measured spectra in passive DOAS applications are typically corrected for rotational Raman scattering (RRS), also called Ring effect, which represents the main contribution to inelastic scattering. In contrast to that, vibrational Raman scattering (VRS) of N2 and O2 has often been thought to be negligible, but also contributes. Consequences of VRS are red-shifted Fraunhofer structures in scattered light spectra and filling-in of Fraunhofer lines, additional to RRS. We describe how to calculate VRS correction spectra in analogy to the Ring spectrum. We discuss further the impact of VRS cross-sections for O2 and N2 on passive DOAS measurements. The relevance of VRS is shown for the first time in spectral evaluations of Multi-Axis DOAS data. This measurement data yields in agreement with calculated scattering cross-sections, that the observed VRS cross-section amounts to 2.2±0.4% of the cross-section of RRS under tropospheric conditions. It is concluded, that this phenomenon has to be included in the spectral evaluation of weak absorbers as it reduces the measurement error significantly and can cause apparent differential optical depth of up to 2.5 × 10-4. Its influence on the spectral retrieval of IO, Glyoxal, water vapour and NO2 in the blue wavelength range is evaluated. For measurements with a large Ring signal a significant and systematic bias of NO2 dSCDs up to (-3.8±0.4) × 1014 molec cm-2 at low elevation angles is observed if this effect is not considered. [ABSTRACT FROM AUTHOR]

The OSIRIS instrument on board the Odin spacecraft has been measuring limb scattered radiance since 2001. The vertical radiance profiles measured as the instrument nods are inverted, with the aid of the SASKTRAN radiative transfer model, to obtain vertical profiles of trace atmospheric constituents. Here we describe two newly developed modes of the SASKTRAN radiative transfer model: a high spatial resolution mode, and a Monte Carlo mode. The high spatial resolution mode is a successive orders model capable of modelling the multiply scattered radiance when the atmosphere is not spherically symmetric; the Monte Carlo mode is intended for use as a highly accurate reference model. It is shown that the two models agree in a wide variety of solar conditions to within 0.2%. As an example case for both models, Odin-OSIRIS scans were simulated with the Monte Carlo model and retrieved using the high resolution model. A systematic bias of up to 4% in retrieved ozone number density between scans where the instrument is scanning up or scanning down was identified. It was found that calculating the multiply scattered diffuse field at five discrete solar zenith angles is sufficient to eliminate the bias for typical Odin-OSIRIS geometries. [ABSTRACT FROM AUTHOR]

The atmospheric energy budget is largely dominated by reactions involving atomic oxygen (O). Modeling of these processes requires detailed knowledge about the distribution of this oxygen species. Understanding the mutual contributions of atomic oxygen and wave motions to the atmospheric heating is the main goal of the rocket campaign WADIS. It includes, amongst others, two of our instruments for the measurement of atomic oxygen that have both been developed with the aim of resolving density variations on small vertical scales along the trajectory. In this paper the instrument based on catalytic effects (PHLUX) is introduced briefly. The experiment employing solid electrolyte sensors (FIPEX) is presented in detail. These sensors were laboratory calibrated using a microwave plasma as a source for atomic oxygen in combination with mass spectrometer reference measurements. The spectrometer was in turn calibrated for O with a method based on methane. In order to get insight into the horizontal variability the rocket payload had instrument decks at both ends. Each housed several sensor heads measuring during both the up- and downleg of the trajectory. The WADIS campaign comprises two rocket flights during different geophysical conditions. Results from WADIS-1 are presented which was successfully launched in June 2013 from Andøya Rocket Range, Norway. FIPEX data was sampled with 100 Hz and yield atomic oxygen density profiles with a vertical resolution better than 10 m. Numerical simulations of the flow field around the rocket were done at several points of the trajectory to assess the influence of aerodynamic effects on the measurement results. Density profiles peak at 3 x 1010 cm-3 at altitudes of 93.6 and 96 km for up- and down-leg respectively. [ABSTRACT FROM AUTHOR]

Increased effectiveness of methane drainage from sealed post-mining goaves in hard coal mines contributes to reduced methane emission from goaves into the mine ventilation system. This paper focuses on issues concerning the assessment of the additional amount of methane released from the goaf into mine workings during periods of atmospheric pressure drops, which can be captured with a methane drainage system. Thanks to the solutions presented in the paper, it is possible to control the efficiency of the goaf drainage system, which in turn leads to the reduction of methane emission from the mine ventilation air into Earth's atmosphere. These solutions are of great added value for both the environment and coal mines as they reduce the costs arising from greenhouse gas emissions that are incurred by mining companies, increasing the efficiency of methane capture and its use in gas engines or district heating systems. The paper uses relationships relating to the influence of atmospheric pressure changes on the process of gas release from the goaf according to the hysteresis loop of methane release during atmospheric pressure changes, which was developed based on conducted research. The analysis and conclusions presented in this paper may facilitate the development of strategies aimed at reducing methane emissions from a mine's ventilated air into Earth's atmosphere. [ABSTRACT FROM AUTHOR]

Billions of historical climatological observations remain unavailable to science as they exist only on paper, stored in numerous archives around the world. The conversion of these data from paper to digital could transform our understanding of historical climate variations, including extreme weather events. Here we demonstrate how the rescue of such paper observations has improved our understanding of a severe windstorm that occurred in February 1903 and its significant impacts. By assimilating newly rescued atmospheric pressure observations, the storm is now credibly represented in an improved reanalysis of the event. In some locations this storm produced stronger winds than any event during the modern period (1950–2015) and it is in the top-4 storms for strongest winds anywhere over land in England and Wales. As a result, estimates of risk from severe storms, based on modern period data, may need to be revised. Examining the atmospheric structure of the storm suggests that it is a classic Shapiro–Keyser-type cyclone with "sting-jet" precursors and associated extreme winds at locations and times of known significant damage. Comparison with both independent observations and qualitative information, such as photographs and written accounts, provides additional evidence of the credibility of the atmospheric reconstruction, including sub-daily rainfall variations. Simulations of the storm surge resulting from this storm show a large coastal surge of around 2.5 m, comparing favourably with newly rescued tide gauge observations and adding to our confidence in the reconstruction. Combining historical rescued weather observations with modern reanalysis techniques has allowed us to plausibly reconstruct a severe windstorm and associated storm surge from more than 100 years ago, establishing an invaluable end-to-end tool to improve assessments of risks from extreme weather. [ABSTRACT FROM AUTHOR]

Despite its widespread commercial use throughout the twentieth century, primarily in the refrigeration industry, dichlorodifluoromethane (CFC-12) is now known to have the undesirable effect of depleting stratospheric ozone. As this long-lived molecule slowly degrades in the atmosphere, monitoring its vertical concentration profile using infrared sounders on satellite platforms crucially requires accurate laboratory spectroscopic data. This work describes new high-resolution infrared absorption cross sections of dichlorodifluoromethane over the spectral range 800-1270 cm-1, determined from spectra recorded using a high-resolution Fourier transform spectrometer (Bruker IFS 125HR) and a 26 cm-pathlength cell. Spectra of dichlorodifluoromethane/dry synthetic air mixtures were recorded at resolutions between 0.01 and 0.03 cm-1 (calculated as 0.9/MOPD; MOPD = maximum optical path difference) over a range of temperatures and pressures (7.5-761 Torr and 190-294 K) appropriate for atmospheric conditions. This new cross-section dataset improves upon the one currently available in the HITRAN and GEISA databases. [ABSTRACT FROM AUTHOR]

In order to avoid problems connected with the content of a priori information in volume mixing ratio vertical profiles measured with the Michelson Interferometer for Passive Atmospheric Sounding (MIPAS), a user-friendly representation of the data has been developed which will be made available in addition to the regular data product. In this representation, the data will be provided on a fixed pressure grid coarse enough to allow a virtually unconstrained retrieval. As to avoid data interpolation, the grid is chosen to be a subset of the pressure grids used by the Chemistry Climate Model Initiative and the Data Initiative within the Stratosphere-troposphere Processes And their Role in Climate (SPARC) project as well as the Intergovernmental Panel of Climate Change climatologies and model calculations. For representation, the profiles have been transformed to boxcar base functions, which means that volume mixing ratios are constant within a layer. This representation is thought to be more adequate for comparison with model data. While this method is applicable also to vertical profiles of other species, the method is discussed using ozone as an example. [ABSTRACT FROM AUTHOR]

Featured Application: This paper demonstrates that the behavior of the horizontal component of seismic wind noise with depth is much more complex than previously published. This fact will motivate increased use of the horizontal component in seismic wind noise studies and should lead to better determination of ground properties using inversion of measured seismic wind noise. In a literature search on the coupling of wind-generated pressure fluctuations into seismic noise, it was noticed that the expression for the angular tilt induced by pressure fluctuations in the seminal paper "A preliminary investigation into the relationship between long-period seismic noise and local fluctuations in the atmospheric pressure" by G. G. Sorrells was only valid at the surface. A search of the literature which cites the Sorrells paper was performed to see if any subsequent research corrected this error, and what effect the error might have on the research. A recent paper by Tanimoto and Wang notes the correct expression for the tilt, but employs the simpler erroneous expression in the research. In this paper, we develop the correct expression for effective measured displacements and approximate expressions analogous to those of Sorrells. The resulting magnitudes and decay with depth are then displayed and compared to Sorrells. Next, the results of the literature search are discussed. The results of three papers are identified as potentially modified by the correction of the tilt calculation. Finally, it is noted that the majority of the papers referenced are not affected by the correction, since many of the papers are for near-surface displacements of very low frequencies. [ABSTRACT FROM AUTHOR]

The commonly used reference atmospheric profiles for the validation of retrieved atmospheric profiles for microwave sounders have bias compared with real atmospheric profile values, which is detrimental to the validation of the retrieval. Microwave sounder observations are the direct measurements of microwave radiation in atmospheric conditions and are a true representation of the status of the atmosphere. This paper proposed a validation method for the retrieved atmospheric temperature and atmospheric humidity profiles of the satellite-based microwave sounder using its own in-orbit observations. The validation experiments are performed both for the retrievals of the microwave temperature sounder-II (Xi'an Branch, China Academy of Space Technology, Xi'an, China. MWTS-II) and the microwave humidity and temperature sounder (National Space Science Center, Chinese Academy of Sciences, Beijing, China. MWHTS). The validation results show that the retrieved temperature profiles of MWTS-II have higher accuracy compared to the temperature profiles of ERA5 in the atmospheric pressure range of 3–30 hPa, and the accuracy of the rest of the pressure range is comparable between the profiles of ERA5 and the retrieved profiles. And the retrieved temperature profiles of MWHTS have higher accuracy compared to the temperature profiles of ERA5 in the atmospheric pressure level around 50 hPa and lower accuracy in the rest of the pressure levels. In addition, the retrieved humidity profiles of MWHTS have higher accuracy compared to the humidity profiles of ERA5 in the atmospheric pressure range of 350–925 hPa. The proposed validation method for the retrieved atmospheric temperature and atmospheric humidity profiles of MWHTS using its own observations is promising for improving the feasibility and reliability of the validation, and can be a good reference for the application of the satellite in-orbit observations and the optimization of the microwave sounders. [ABSTRACT FROM AUTHOR]

The construction of sub‐daily pressure series is described for the cities of London (GB) and Paris (FR). The series extend back 1692 and 1748, respectively, and as such they represent two of the longest sub‐daily series of barometric pressure available. These series are updated from the previously documented London and Paris daily series and offer more homogeneous series, and in the case of the London series a more temporally complete sequence of data. A pairwise homogenization procedure has been applied to the two series alongside the long series of pressure that exists for De Bilt (NL). The De Bilt series has been available for some time in the International Surface Pressure Dataset (ISPD), but further quality control and homogeneity‐checking procedures have been applied to the data in this paper and therefore the three series are released together in this dataset. The series are of immediate interest for understanding changes to storm activity across the English Channel and North Atlantic region over an extended timeframe but may also be assimilated into reanalysis datasets such as the 20th‐century reanalysis. [ABSTRACT FROM AUTHOR]

Increasing the number of resistant bacteria resistant to treatment is one of the leading causes of death worldwide. These bacteria are created in wounds and injuries and can be transferred through hospital equipment. Various attempts have been made to treat these bacteria in recent years, such as using different drugs and new sterilization methods. However, some bacteria resist drugs, and other traditional methods cannot destroy them. In the meantime, various studies have shown that cold atmospheric plasma can kill these bacteria through different mechanisms, making cold plasma a promising tool to deactivate bacteria. This new technology can be effectively used in the food industry because it has the potential to inactivate microorganisms such as spores and microbial toxins and increase the wettability and printability of polymers to pack fresh and dried food. It can also increase the shelf life of food without leaving any residue or chemical effluent. This paper investigates cold plasma's potential, advantages, and disadvantages in the food industry and sterilization. [ABSTRACT FROM AUTHOR]