Search

A novel technique for transmission of information through visible light communication (VLC) is developed in this study. A light-emitting diode is used as the light source at the transmitting side to send the encrypted information. At the receiving side, a light sensor, OPT-101, is used to receive the light signals that carry the encrypted information. The Arduino Due microcontroller board is used for digital signal processing at both the transmitting and receiving sides. Furthermore, to prevent the transmitted message from being intercepted, two chaotic systems, a master and a slave, with a synchronization controller are designed to obtain the transmitted audio signals. The design enables not only a VLC system with the light transmission path as a straight line (so that data cannot be stolen) but also the encryption of the audio signals with the chaotic system (Rössler system) to enhance data transmission security. The effectiveness of this system is then experimentally verified. [ABSTRACT FROM AUTHOR]

High-speed, low-power analog-to-digital converter (ADC) is a critical element for 5-GBd, 20-Gb/s digital signal processing (DSP)-based coherent optical communication receiver. To satisfy high data transmission rate requirement of optical receiver, a single-core and open-loop flash ADC with a new proposed multiplexer-based encoder is presented in this paper. Compared with conventional encoder topology, the new proposed topology achieves the fastest encoding speed and lowest power consumption. The optimized distortion is achieved by utilizing a leakage current compensation technique and a local negative feedback method in switched-buffer track-and-hold amplifier (THA). Strict synchronization is obtained for clock signals by careful designing of layout in tree-based clock networks. Furthermore, a master–slave comparator incorporated with a preamplifier reduces signal-dependent kickback noise as well as offset voltage. By using master–slave comparators and proposed encoders, the sampling rate is up to 21.12 GS/s. The 4-bit, 20-GS/s flash ADC is realized in 0.13- μ m SiGe BiCMOS technology and it only occupies 1.05 mm × 1.46 mm chip area. With a power consumption of 1.831 W from 4-V supply, the ADC achieves an effective number of bits (ENOB) of 2.5 at 15 GS/s. [ABSTRACT FROM AUTHOR]

With advances in solid-state lighting, visible light communication (VLC) has emerged as a promising technology to enhance existing light-emitting diode (LED)-based lighting infrastructure by adding data communication capabilities to the illumination functionality. The last decade has witnessed the evolution of the VLC concept through global standardisation and product launches. Deploying VLC systems typically requires replacing existing light sources with new luminaires that are equipped with data communication functionality. To save the investment, it is clearly desirable to make the most of the existing illumination systems. This paper investigates the feasibility of adding data communication functionality to the existing lighting infrastructure. We do this by designing an experimental system in an indoor environment based on an off-the-shelf LED panel typically used in office environments, with the dimensions of 60 × 60 cm 2 . With minor modifications, the VLC function is implemented, and all of the modules of the LED panel are fully reused. A data rate of 40 Mb/s is supported at a distance of up to 2 m while using the multi-band carrierless amplitude and phase (CAP) modulation. Two main limiting factors for achieving higher data rates are observed. The first factor is the limited bandwidth of the LED string inside the panel. The second is the flicker due to the residual ripple of the bias current that is generated by the panel's driver. Flicker is introduced by the low-cost driver, which provides bias currents that fluctuate in the low frequency range (less than several kilohertz). This significantly reduces the transmitter's modulation depth. Concurrently, the driver can also introduce an effect that is similar to baseline wander at the receiver if the flicker is not completely filtered out. We also proposed a solution based on digital signal processing (DSP) to mitigate the flicker issue at the receiver side and its effectiveness has been confirmed. [ABSTRACT FROM AUTHOR]

The authors propose a transmitter digital filter for joint optimisation of signal pulse shaping and chromatic dispersion pre-compensation, providing a detailed analysis of the architecture complexity. Experimental transmission of 40 × 50G channels (28 Gbaud four-level pulse amplitude modulation) over up to 110 km uncompensated standard single mode fibre with low-bandwidth hardware is demonstrated. [ABSTRACT FROM AUTHOR]