Search

Metal-organic frameworks (MOFs) have the advantages of tunable pore sizes and porosity and have demonstrated unique advantages for various applications. This study synthesized composite MOF nanomaterials by modifying MOF801 or AlOOH with UIO66. The composite nanomaterials, UIO66/MOF801 and UIO66/AlOOH showed increased Zeta potential than their pristine form, AlOOH, UIO66 and MOF801. For the first time, the composite MOFs were used to fabricate filter paper-based evaporation-driven power generators for spontaneous electricity generation. The MOFs-KBF membrane was constructed by coating filter paper (10 × 50 mm) with composite MOFs and conductive Ketjen Black. The UIO66/MOF801 decorated device achieved a maximum open circuit voltage of 0.329 ± 0.005 V and maximum output power of 2.253 μW. The influence of salt concentration (0.1–0.5 M) on power generation was also analyzed and discussed. Finally, as a proof-of-concept application, the device was employed as a salinity sensor to realize remote monitoring of salinity. This work demonstrated the potential of flexible MOF composites for spontaneous power generation from water evaporation and provides a potential way to enhance the performance of evaporation-driven power generators. [ABSTRACT FROM AUTHOR]

The research presented in this paper introduces a novel environmental energy‐harvesting technology that harnesses electricity from the evaporation of water using porous structural materials. Specifically, a strategy employing paper‐based hydroelectric generators (p‐HEGs) is proposed to capture the energy produced during water evaporation and convert it into usable electricity. The p‐HEGs offer several advantages, including simplicity in fabrication, low cost, and reusability. To evaluate their effectiveness, the water evaporation‐induced electrical output performance of four different p‐HEGs are compared. Among the variants tested, the p‐HEG combining wood pulp and polyester fiber exhibits the best output performance. At room temperature, this particular p‐HEG generates a short‐circuit current and open‐circuit voltage of ≈0.4 µA and 0.3 V, respectively, thereby demonstrating excellent electrical stability. Furthermore, the electrical current and voltage generated by the p‐HEG through water evaporation are able to power an LED light, both individually and in series and parallel connections. This study delves into the potential of electricity harvesting from water evaporation and establishes it as a viable method for renewable energy applications. [ABSTRACT FROM AUTHOR]

Microbial fuel cell is a promising technology to harvest energy from wastewater, and effective anode catalysts are essential for its applications. In this study, zero-dimension nitrogen-doped carbon dots, as biocompatible efficient modifiers, were synthesized and decorated onto the carbon paper surface to prepare microbial fuel cell anode. The as-fabricated nitrogen-doped carbon dots decorated carbon paper anode was able to enhance electricity generation and efficient wastewater treatment. It was found that the as-fabricated electrode had a high hydrophilicity, which was favorable for the microbial immobilization. Compared with the carbon paper anode, the biofilm on the as-prepared anode was almost twice of thickness. After introducing nitrogen-doped carbon dots, the extracellular electron transfer process from the microorganisms to the anode was enhanced. The microbial fuel cell with the as-developed anode generated a remarkable power output of 0.32 mW, 1.1 times higher than that of the raw carbon paper anode with same measurement area. Moreover, 16 sRNA pyrosequencing analysis shows that the quantity of Pseudomonas on the electrode increased by ∼40%, which also promoted the electron transfer rate by excreting mediators like phenazines or phenazine derivatives. This work developed a new approach to design microbial fuel cell anode material and fabricate a high-efficiency and environmentally friendly anode for electricity generation from wastewater. Image 100697 • Notable power output was obtained from MFC with N-doped CDs@carbon paper electrode. • The carbon paper electrode was highly hydrophilic by decorating with N-doped CDs. • The EET efficiency was enhanced by modifying the electrode with N-doped CDs. • The relative abundance of Pseudomonas was enhanced with N-doped CDs' decoration. [ABSTRACT FROM AUTHOR]

The subsector of pulp and paper presented in 2013 an electric power consumption of 9.3% of electricity consumption in the industrial sector in Brazil. It experienced a significant growth of production in the last 20 years, exceeding 160%, and their consumption of electricity increased by 130%, reaching the level of 19,594GWh. Due to its characteristics, with a known structure and production processes, and its importance in the country's industrial sector, this subsector was selected for study in this paper, to evaluate the behavior of its long-term annual electricity demand, at the horizon of 20 years ahead, in energy efficiency scenarios through bottom-up approach. This approach is data intensive and requires data with good quality; it consists of a hierarchical structure that enables to check how specific actions can affect the results at each level and its effect on higher levels. [ABSTRACT FROM AUTHOR]

The recovery and utilisation of industrial excess heat has been identified as an important contribution for energy efficiency by reducing primary energy demand. Previous works, based on top-down studies for a few sectors, or regional case studies estimated the overall availability of industrial excess heat. A more detailed analysis is required to allow the estimation of potentials for specific heat recovery technologies, particularly regarding excess heat temperature profiles. This work combines process integration methods and regression analysis to obtain cogeneration targets, detailed excess heat temperature profiles and estimations of electricity generation potentials from low and medium temperature excess heat. The work is based on the use of excess heat temperature (XHT) signatures for individual sites and regression analysis using publicly available data, obtaining estimations of the technical potential for electricity generation from low and medium temperature excess heat (60–140 °C) for the whole Swedish kraft pulp and paper industry. The results show a technical potential to increase the electricity production at kraft mills in Sweden by 10 to 13%, depending on the level of process integration considered, and a lower availability of excess heat than previously estimated in studies for the sector. The approach used could be adapted and applied in other sectors and regions, increasing the level of detail at which industrial excess heat estimations are obtained when compared to previous studies. [ABSTRACT FROM AUTHOR]

Demand response (DR) is one of the most cost-effective and logical smart grid terms for power systems that can be used during peak load hours, whereas load shedding (LS) is the last and most expensive solution in emergency grid situations. The aim of them is to satisfy equilibrium constraints between consumption and generation and restore the power system frequency to normal bounds at the least possible time. The rapid increase in power grid costs and limitations on electricity generation resources have resulted in the increasing need for industrial customers' participation as an alternative solution to peak load spikes. Therefore, this paper considers the estimation of imbalance active power in a smart strategy to introduce a critical DR (CDR) in heavy industries (pulp and paper, cement, and medium density fibreboard (MDF)) based on direct load control (DLC) technique in order to reduce the need for LS in frequency restore. To evaluate the proposed model, a real case study including the typical pulp and paper, cement, and MDF industries processes with actual power consumption data is considered. The numerical and graphical results confirm that the proposed CDR can be used as an inexpensive solution to replace the costly spinning reserves and avoid load shedding. [ABSTRACT FROM AUTHOR]

[Display omitted] • Various carbon nanotube-based devices are developed for solar energy utilization. • The water evaporation system can generate freshwater (1.28 kg m−2h−1). • The solar-thermoelectric system can output a voltage and charge a cellphone. • The supercapacitor performs an areal specific capacitance of 19.6 mF cm−2. • The hybrid energy system can produce freshwater, generate and store electric power. Nowadays, multi-functional systems driven by solar energy have been explored to alleviate the crisis of energy and freshwater scarcity. However, it remains a great challenge to integrate multi-functions into one hybrid system with a monolithic material, which can harvest, convert and store solar energy synergistically. Here, we firstly propose a multi-functional carbon nanotube paper, which starts from a material level to solve these problems. The carbon nanotube paper is fabricated by vacuum filtration. It exhibits high efficiency of solar-thermal conversion. Secondly, three types of energy conversion/storage systems (e.g., solar-thermal evaporation system, solar-thermoelectric generation system, and supercapacitor) are constructed based on the carbon nanotube paper, which extend the research to a device level. The solar-thermal evaporation system shows an evaporation rate of 1.28 kg m-2h−1 under simulated sunlight irradiation of 1 kW m−2. The solar-thermoelectric generation system demonstrates a stable electric power generation with an output voltage of 100 mV under light irradiation of 1 kW m−2. The supercapacitors perform the energy storage function with an areal specific capacitance of 19.6 mF cm−2. These devices and systems can be used in freshwater generation (0.84 kg m-2h−1, sunlight irradiation of 1 kW m−2), water purification/desalination (inorganic ions rejection larger than 99.9%) and portable solar charging system (maximum output voltage of 5 V). Finally, a hybrid energy system is innovatively proposed from the system level to simultaneously produce freshwater, generate and store electric power. Through the synergetic coupling of solar conversion and storage technologies, the hybrid energy system can supply sustainable freshwater and electricity for remote areas in daily life, highlighting the superiority of multi-energy (thermal energy, electrical energy, and electrochemical energy) complementary. [ABSTRACT FROM AUTHOR]

Highlights • We develop a novel portable and disposable paper-based biobattery. • Our biobattery is on-demand electricity generation activated by a drop of tap water. • A low-cost, simple-structure battery case is created by single layer of paper filter. • We proposed integrated air-cathode paper-based proton exchange membrane. • Proposed battery can be used for paper-based diagnostic devices. Abstract A novel, portable, and disposable paper-based microbial fuel cells (MFC) generating electricity from harmless strain of Escherichia coli (E. coli) has been developed. This MFC is on-demand electricity generation activated by a drop of tap water in a dry anode containing the biofilm of E. coli. A low-cost, simple-structure MFC case was created by a single layer of paper filter with high order of folding, which could support interchangeable dry bacteria-loaded anodes. The paper filter was innovatively engineered to make an integrated air-cathode proton exchange membrane (ACPEM) by coating carbon nanotube mixed with potassium ferricyanide on one surface and spraying hydrophobic solution on the other surface, respectively. The E. coli biofilm pre-inoculated in the anodes made of activated carbon sheet was simply dried in the air for the sake of long-term storage and usage. The dry anodes can be simply set in the MFC case with the readily prepared ACPEM, which can be used for on-demand power generation within seconds after adding water with maximum power density of 8.8μW/cm2. [ABSTRACT FROM AUTHOR]

The central role of electricity in shaping the worldwide economy is broadly acknowledged in the energy literature. Having identified the then ongoing crisis of the electricity sector, the present Awami League government initiated restructuring the energy sector since 2009 to quicken the pace of the developmental activities. All these efforts resulted in landmark achievements in the Bangladesh energy sector, especially in increasing the electricity generation capacity. However, the global Covid-19 pandemic and its aftermath effects on the Bangladesh economy require a policy revision in Bangladesh's energy sector and electricity generation mix. To our knowledge, there is no study to analyse the adverse consequences of the Covid-19 in Bangladesh energy sector. By employing a SARIMA forecasting model, we reveal that electricity demand will remain less than the actual generation in the upcoming two years. Also, the DGE model finds that due to Covid-19, the economic growth rate will be around 4.5 percent in the long-run. We further simulate that the steady-state electricity demand and standard consumption values would fall by 8-10 percent and 6 percent, respectively. We recommend that a review of the power sector master plan is needed for future energy security and economic stability in Bangladesh. [ABSTRACT FROM AUTHOR]