Search

A beam optics study using the ITER-relevant high intense negative ion beams, such as 1 MeV, 200 A/m2, has been performed experimentally and analytically using a multi-aperture and five-stage accelerator. Initially, multi-beamlets generated from this accelerator were deflected in various directions due to the magnetic field and space charge repulsion between beams and showed various divergences. These had limited the pulse length and the beam energy. Compensation methods of the beamlet deflections have worked effectively and contributed to achieving the ITER requirement, the divergence angle of <7 mrad, and the deflection angle of <1 mrad for 1 MeV beam. The beam pulse has been gradually extended from 1 to 100 s and is now going to a longer pulse based on these results. One of the remaining issues is to understand and suppress peripheral components of the beam, namely, the halo, and to reduce the local heat loads observed around the aperture edge. This halo component has been successfully distinguished from the beam core by using a newly developed beam emittance measurement system for high intense beams. By combining this measured beam emittance and the beam simulation, it was clarified for the first time that the halo components are generated in an area of 1 mm width from the aperture edge. [ABSTRACT FROM AUTHOR]

In multi-beamlet negative ion accelerators for neutral beam injectors, the transverse magnetic field necessary for suppressing the co-extracted electrons induces a deflection of the negative ion beamlets that must be corrected. For the design, particle-tracing simulation codes are used to compute ion trajectories and optical properties of the beamlets in the acceleration stage. In these codes, uniform boundary conditions are normally assumed for the ion current density distribution at the surface (called meniscus), where negative ions are extracted from the plasma and form beamlets, which are accelerated across the apertures of the accelerator grids. Recently, experimental campaigns dedicated to the accurate measurement of the beamlet deflection in the acceleration phase revealed higher deflection than foreseen by simulations. In this work, we demonstrate that an agreement with the experimental data can be obtained by incorporating in the numerical simulations a non-radially symmetric distribution of the ion current density extracted across the meniscus surface. In the first part, the asymmetry of the ion current density at the meniscus is studied in an empirical way, by analysing and fitting the experimental results obtained with different operating parameters. In the second part, we show that the ion current asymmetry estimated by this procedure is well consistent with the flow pattern of H− ions calculated in the meniscus zone using a detailed particle in cell (PIC) model of the ion source in the presence of transverse magnetic field. [ABSTRACT FROM AUTHOR]

To realize stable negative ion beams for 100 s required in the neutral beam injector of JT-60SA, a physical model to control cesium (Cs) distribution inside the negative ion source has been developed in order to maintain the stable negative ion production at the plasma grid (PG) surface with Cs. In this work, to quantitatively evaluate Cs coverage on the PG, a three-dimensional Cs transportation code was introduced to consider the spatial Cs distribution in the source. The spatial temperature distribution of the chamber wall was also introduced in this model. As a result, the reasonable variation of the Cs coverage for 100 s was obtained, compared to that in the initial model. Based on the modified model, the operational temperature of the chamber wall was proposed to be less than 60 °C to suppress the desorption of Cs in the chamber wall and to sustain the stable negative ion production. In addition, it was also suggested that a slightly higher wall temperature before the operation leads to a decrease in the amount of Cs stored at the chamber wall, resulting in suppression of Cs consumption in the ion source. [ABSTRACT FROM AUTHOR]

Long pulse acceleration of hydrogen negative ion beams with the power density over 70 MW/m2 and the pulse length over 100 s has been demonstrated for the first time by using a multi-aperture 3-stage accelerator. Such long pulse acceleration was achieved by integrating the design of beam optics and voltage holding capability to meet the requirements of JT-60SA. By using the newly designed accelerator for JT-60SA, voltage holding at 500 kV with beam acceleration was stably sustained even after 5 g of cesium was seeded, and heat load on each acceleration grid was reduced below the allowable level for long pulse, less than 5% of total acceleration power. As a result, 500 keV, 154 A/m2 for 118 s beam acceleration was achieved, which satisfies the requirement of the negative ion source for JT-60SA. This pulse length of such high-power density beams is longest in the world. In addition, the result contributes to the long pulse acceleration of multi-stage electrostatic accelerators, such as 1 MeV negative ion accelerator for ITER. [ABSTRACT FROM AUTHOR]

In order to reduce the tritium inventory in a fuel circulation system in fusion plants, a possibility of deuterium-tritium (DT) mixed neutral beam injectors with DT negative ion beams has been investigated by analyzing the beam optics of the DT-mixed negative ion beams for the first time. In a two-dimensional beam analysis, DT-mixed ion beams could be accelerated regardless of the DT current mixing ratio (T/D) from the identical acceleration geometry with the identical applied voltages by adjusting total space charge for the D and T components. However, in a three-dimensional beam analysis including magnetic fields, the DT-mixed ion beams were separated due to a mass dependence of the beam deflection by orthogonal magnetic fields of an electron suppression and transverse filter fields for negative ion production. In the case of the beamline for ITER, which requires beam deflection angle within ±1 mrad, the operational range for the DT-mixed ion beams was found to be the DT current mixing ratio of 0.7-1.5 and beam energy of 0.9-1.0 MeV. Although the operational range was not wide, the DT-mixed beam was found to be feasible in terms of the beam acceleration. These analyses also contribute to the study of the acceleration of other mixed ion beams such as impurity or heavy ions, which are useful techniques for diagnostic beams. [ABSTRACT FROM AUTHOR]

In order to realize negative ion sources and accelerators to be applicable to International Thermonuclear Experimental Reactor and JT-60 Super Advanced, a large cesium (Cs)-seeded negative ion source and a multi-aperture and multi-stage electric acceleration have been developed at Japan Atomic Energy Agency (JAEA). Long pulse production and acceleration of the negative ion beams have been independently carried out. The long pulse production of the high current beams has achieved 100 s at the beam current of 15 A by modifying the JT-60 negative ion source. The pulse duration time is increased three times longer than that before the modification. As for the acceleration, a pulse duration time has been also extended two orders of magnitudes from 0.4 s to 60 s. The developments of the negative ion source and acceleration at JAEA are well in progress towards the realization of the negative ion sources and accelerators for fusion applications. [ABSTRACT FROM AUTHOR]

To understand the physics of the cesium (Cs) recycling in the large Cs-seeded negative ion sources relevant to ITER and JT-60SA with ion extraction area of 45-60 cm × 110-120 cm, the time evolution of the negative ion profile was precisely measured in JT-60SA where the ion extraction area is longitudinally segmented into 5. The Cs was seeded from the oven at 180 °C to the ion source. After 1 g of Cs input, surface production of the negative ions appeared only in the central segment where a Cs nozzle was located. Up to 2 g of Cs, the negative ion profile was longitudinally expanded over full ion extraction area. The measured time evolution of the negative ion profile has the similar tendency of distribution of the Cs atoms that is calculated. From the results, it is suggested that Cs atom distribution is correlated with the formation of the negative ion profile. [ABSTRACT FROM AUTHOR]

• Joint experimental campaigns carried out in QST lab in Naka, Ibaraki, Japan. • Full compensation of magnetic criss-cross deflection of beamlets obtained. • Non-uniform extraction assumed for interpreting the experimental results. • Numerical simulations can reproduce the experimental results with good accuracy. In the framework of the collaboration between Consorzio RFX (Padova, Italy) and QST (Naka, Japan) two experimental campaigns have been organized on the Negative Ion Test Stand (NITS) in Naka, employing an ITER-like multi-beamlet configuration. These campaigns were aimed at compensating for the undesired magnetic deflection of the ion beam. The experiments have clarified the influence of operating parameters on the optical properties of the ion beam. The physical phenomena acting on the optics have been investigated, in particular the effect of an asymmetry of the ion current density at meniscus. Comparisons with simulations have been made and the modeling has been improved consequently. During the second experimental campaign, a perfect compensation of the ion deflection has been achieved. [ABSTRACT FROM AUTHOR]

• Experimental campaign on MTF carried out in QST lab in Naka, Ibaraki, Japan. • Opera, SLACCAD, COMSOL, EAMCC3D correctly predict beam divergence. • Semi-empirical Opera model with current density asymmetry correctly predicts the beam deflection. • COMSOL and EAMCC3D slightly underestimate heat loads on the grids. It is a widely recognized phenomenon that, in negative ion sources for NBI, the magnetic fields in the source cause an asymmetry of the current density at the meniscus, which affects the beam optics. In order to achieve a more realistic estimation of the negative ion beam optics, the ion current density profile at the beamlet meniscus is sometimes assumed to be non-symmetric with respect to the beamlet axis. The new hypothesis tested in this paper is an empirical law obtained by recent investigations on a similar Kamaboko ion source, which relates this asymmetry to the magnetic field strength at the meniscus and to the power injected in the ion source. For the first time this hypothesis is used to directly and correctly predict the value of the beamlet deflection. The MeV ion source Test Facility (MTF) is a high voltage negative ion beam accelerator dedicated to fusion experiments in QST, Naka, Ibaraki, Japan. MTF can be operated as a three- or five-stage multi-aperture accelerator with a configuration and beam energy comparable to the future ITER NBI. In 2019, experiments were conducted on MTF aiming at accelerating a H- beam with high energy and good optics for a long duration of the beam (around 100 s). These experiments allowed to measure the beamlet divergence and deflection as well as the heat loads due to particle impinging on the accelerator grids, over a wide range of operating parameters. The predictions of several beam simulation codes (Opera, COMSOL, SLACCAD, EAMCC3D) have been compared to the experimental measurements, which allows to obtain a good agreement in terms of beam optics and a fair agreement in terms of heat loads. [ABSTRACT FROM AUTHOR]