Search

The use of microalgae and bacteria as a strategy for the startup of bioreactors for the treatment of industrial wastewater can be a sustainable and economically viable alternative. This technology model provides satisfactory results in the nitrification and denitrification process for nitrogen removal, organic matter removal, biomass growth, sedimentation, and byproducts recovery for added-value product production. The objective of this work was to evaluate the performance of microalgae and bacteria in their symbiotic process when used in the treatment of paper pulp industry wastewater. The experiment, lasting fourteen days, utilized four bioreactors with varying concentrations in mgVSS/L of microalgae to bacteria ratio (R1-100:100, R2-100:300, R3-100:500, R4-300:100) in the startup process. Regarding the sludge volumetric index (SVI), the results show that the R1 and R2 reactors developed SVI30/SVI10 biomass in the range of 85.57 ± 7.33% and 84.72 ± 8.19%, respectively. The lipid content in the biomass of reactors R1, R2, R3 e R4 was 13%, 7%, 19%, and 22%, respectively. This high oil content at the end of the batch, may be related to the nutritional stress that the species underwent during this feeding regime. In terms of chlorophyll, the bioreactor with an initial inoculation of 100:100 showed better symbiotic growth of microalgae and bacteria, allowing exponential growth of microalgae. The total chlorophyll value for this bioreactor was 801.46 ± 196.96 μg/L. Biological removal of nitrogen from wastewater from the paper pulp industry is a challenge due to the characteristics of the effluent, but the four reactors operated in a single batch obtained good nitrogen removal. Ammonia nitrogen removal performances were 91.55 ± 9.99%, 72.13 ± 19.18%, 64.04 ± 21.34%, and 86.15 ± 30.10% in R1, R2, R3, and R4, respectively., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

The proper treatment and utilization of kraft black liquor, generated from the pulp and paper industry through the kraft pulping method, is required to reduce environmental impacts prior to the final disposal. It also improves the economic performance through the utilization of waste. Microbial valorization appears to demonstrates the dual benefits of waste management and resource recovery by providing an innovative solution to convert kraft black liquor into resource for reuse. A comprehensive review on the microbial valorization of kraft black liquor, describing the role in valorization and management, is still lacking in the literature, forming the rationale of this article. Thus, the present study reviews and systematically discusses the potential of utilizing microorganisms to valorize kraft black liquor as a sustainable feedstock to develop a numerous portfolio of platform chemicals, bioenergy, and other value-added products. This work contributes to sustainability and resource efficiency within the pulp and paper industry. The recent developments in utilization of synthetic biology tools and molecular techniques, including omics approaches for engineering novel microbial strains, for enhancing kraft black liquor valorization has been presented. This review explores how the better utilization of kraft black liquor in the pulp and paper industry contributes to achieving UN Sustainable Development Goals (SDGs), particularly clean water and sanitation (SDG 6) as well as the affordable and clean energy goal (SDG 7). The current review also addresses challenges related to toxicity, impurities, low productivity, and downstream processing that serve as obstacles to the progress of developing highly efficient bioproducts. The new directions for future research efforts to fill the critical knowledge gaps are proposed. This study concludes that by implementing microbial valorization techniques, the pulp and paper industry can transition from a linear to a circular bioeconomy and eco-friendly manage the kraft black liuor. This approach showed to be effective towards resource recovery, while simultaneously minimizing the environmental burden., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

A new porous solid base catalyst was prepared using dewatered paper sludge and successfully employed to produce biodiesel from soybean oil. The as-prepared catalyst was characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Fourier transforms infrared spectroscopy, X-ray photoelectron spectroscopy, thermal gravity/differential thermal gravity analysis, Brunauer-Emmet-Teller analysis, and CO 2 -temperature programmed analysis. The results showed that the formation of CaO and uniformly distributed porous structure should account for the high catalytic activity of the as-prepared catalyst. The optimum reaction conditions were observed at 180 ℃, 8 wt.% catalyst/oil weight ratio, 16:1 methanol/oil molar ratio, and 300 min reaction time with 91.6% biodiesel yield. After being used several times and recycled, the regenerated catalyst still exhibited effective catalytic activity without apparent deactivation. The kinetic study confirmed that the experimental data satisfied with Pseudo-first-order kinetic model controlled by reaction temperature and catalyst/oil weight ratio. The reaction activation energy was 24.98 kJ/mol. The change of enthalpy ΔH (14.98 kJ/mol), entropy ΔS (-208.57 J/mol/K), and Gibbs free energy ΔG (109.46 kJ/mol) indicated that the transesterification reaction catalyzed by the dewatered paper sludge-derived catalyst is endothermic, endergonic, and non-spontaneous. Our research finding indicated that the CaO-based catalyst derived from dewatered paper sludge was an economically promising and eco-friendly solid base catalyst for biodiesel production.

Objective: The main objective of this study is the evaluation of RPPW anaerobic digestion feasibility at laboratory scale under Mesophilic condition. The experiment is conducted using a two-stage biofilm digester of 5 L capacity with mobile support material., Results: Anaerobic treatment of wastewater from recycled pulp and paper industry in Morocco was tested using a laboratory-scale anaerobic biofilm digester that operated under mesophilic conditions over a 70-day. Chemical oxygen demand (COD) efficiency, volatile and total solid (VS, TS) elimination of the substrate during the process were: 78%, 52% and 48% respectively. The system was stable throughout its operating cycle with an optimum pH (7.24), alkalinity (1750 mg CaCO 3 /L) and a volatile fatty acid value (760 mg/L). The experimental daily biogas production measured reaches a value of 5 L/day with a composition of 71% methane, 27.6% carbon dioxide, 0.2 oxygen and 7713 ppm of the H 2 S. The study results show that the anaerobic biofilm reactor is a suitable technique for recycled pulp and paper wastewater (RPPW) treatment. The reactor shows high performances in terms of process stability, removal efficiency (> 70%) and biogas production., Conclusion: Anaerobic digestion is an efficient waste treatment technology that uses natural anaerobic decomposition to reduce the volume of waste while producing biogas. However, research is needed to strengthen microbial metabolism, biochemistry and the functioning of the rector to improve biogas production. The RPPW AD experiment with biofilm digester technology was stable throughout the operation period. The digester knows an overloaded in the last phase of the experiment which leads to an inhibition of biogas production.

Paper mill sludge (PMS) was assessed as cheap renewable lignocellulosic biomass for lipid production by the oleaginous yeast Cryptococcus vishniaccii (MTCC 232). The sonicated paper mill sludge extract (PMSE) exhibited enhanced lipid yield and lipid content 7.8±0.57g/l, 53.40% in comparison to 5.5±0.8g/l, 40.44% glucose synthetic medium, respectively. The accumulated triglycerides (TAG) inside the lipid droplets (LDs) were converted to biodiesel by transesterification and thoroughly characterized using GC-MS technique. The fatty acid methyl ester (FAME) profile obtained reveals elevated content of oleic acid followed by palmitic acid, linoleic acid and stearic acid with improved oxidative stability related to biodiesel quality., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

Paper sludge (PS) from the paper and pulp industry consists primarily of cellulose and ash and has significant potential for ethanol production. Thirty-seven PS samples from 11 South African paper and pulp mills exhibited large variation in chemical composition and resulting ethanol production. Simultaneous saccharification and fermentation (SSF) of PS in fed-batch culture was investigated at high solid loadings and low enzyme dosages. Water holding capacity and viscosity of the PS influenced ethanol production at elevated solid loadings of PS. High viscosity of PS from virgin pulp mills restricted the solid loading to 18% (w/w) at an enzyme dosage of 20 FPU/gram dry PS (gdPS), whereas an optimal solid loading of 27% (w/w) was achieved with corrugated recycle mill PS at 11 FPU/gdPS. Ethanol concentration and yield of virgin pulp and corrugated recycle PS were 34.2g/L at 66.9% and 45.5 g/L at 78.2%, respectively., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

The membrane process had been applied for the advanced treatment of pig farm biogas slurry. As studied, this physical pretreatment, with low cost and high efficiency of the suspended solids removal and nutrient retention, is required to control membrane fouling. The combined process of paper filtration and ultrafiltration in a pilot scale was applied in the present study. The main objective was to explore and identify the feasibility of the new process for the pretreatment of the separation liquid of pig farm biogas slurry. A precision identification experiment of paper filtration and the multi-batch repetitive experiments of the combined process were designed. The results showed, at the identified paper filtration precision of 50μm and an operating pressure of 0.3 bar of the ultrafiltration process, that the flux rate at the stable stage of the multi-batch operation was around 295.00 L/h. The combined process achieved an overall processing rate of 345.41 ± 18.81 L/h and a volume permeation proportion of 82.45% ± 0.85%. The TSS was removed by 95.71%, but total nitrogen (TN) and ammonia nitrogen (NH₃-N) were retained by 76.29% ± 2.04% and 73.74% ± 2.10%, respectively. Comprehensively, the requirement for the pretreatment was obtained.

A strategy that combines visible-light-enhanced biofuel cells (BFCs) and electrochemical immunosensor into paper-based analytical devices was proposed for sensitive detection of the carbohydrate antigen 15-3 (CA15-3). The gold nanoparticle modified paper electrode with large surface area and good conductibility was applied as an effective matrix for primary antibodies. The glucose dehydrogenase (GDH) modified gold-silver bimetallic nanoparticles were used as bioanodic biocatalyst and signal magnification label. Poly(terthiophene) (pTTh), a photoresponsive conducting polymer, served as catalyst in cathode for the reduction of oxygen upon illumination by visible light. In the bioanode, electrons were generated through the oxidation of glucose catalyzed by GDH. The amount of electrons is determined by the amount of GDH, which finally depended on the amount of CA15-3. In the cathode, electrons from the bioanode could combine with the generated holes in the HOMO energy level of cathode catalysts pTTh. Meanwhile, the high energy level photoexcited electrons were generated in the LUMO energy level and involved in the oxygen reduction reaction, finally resulting in an increasing current and a decreasing overpotential. According to the current signal, simple and efficient detection of CA15-3 was achieved.

Fines concentration harms paper machine runability and output quality in recovered paper processing, hence, their extraction would be fundamentally beneficial. In this study, separated fines from an industrial recycled fiber pulp (RFP) were characterized and evaluated for their potential biogas yields with a focus on understanding the role of varying lignin and ash contents. Further, these results were compared with biogas yields from conventional chemical and mechanical pulps. Overall, methane yields of fines from mechanical pulps (21-28mL/gVS) and RFP (127mL/gVS) are relatively low compared to the high methane yields of 375mL/gVS from the chemical pulp fines. However, it was shown that the high ash content in RFP fines (up to 50%) did not negatively influence overall yield, rather, it was the presence of slowly biodegrading lignin-rich fiber fines., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Two temperature-phased anaerobic digestion (TPAD) systems (55 °C in the first reactor and 35 °C in the second reactor) with and without recirculation were operated in parallel for the co-digestion of food waste and paper waste. A long-term experiment was carried out for these two systems with the paper waste ratios elevated from 0 to 50%. The removal efficiencies of COD, TS, VS, carbohydrate and protein in the recirculated TPAD system were higher than those of the non-recirculated system. The successful acclimation of thermophilic cellulose-degrading bacteria in the first reactor (RT1), partly due to recirculation, ensured the effective degradation of cellulose when the paper waste ratio was higher than 40%, resulting in the production of large amounts of hydrogen in reactor RT1. In the absence of recirculation, the main substance produced in the first reactor of the non-recirculated system (T1) was lactic acid. This gradually led to over-acidification and a low degradation efficiency and no methane or hydrogen was produced in T1. Recirculation helped to establish a stable bacterial community capable of producing bio-hydrogen in reactor RT1. The relatively low pH of 5.5 in the RT1 inhibited the activity of hydrogenotrophic archaea without consuming hydrogen, facilitating high hydrogen production levels., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020 Elsevier B.V. All rights reserved.)

Recycled paper mill effluent (RPME) consists of various organic and inorganic compounds. In this study, modified anaerobic hybrid baffled (MAHB) bioreactor has been successfully used to anaerobically digest RPME. The anaerobic digestion was investigated in relation to methane production rate, lignin removal, and chemical oxygen demand (COD) removal, with respect to organic loading rate (OLR) and hydraulic retention time (HRT). The analysis using kinetic study was carried out under mesophilic conditions (37 ± 2 °C) and influent COD concentrations (1000-4000 mg L -1 ), to prove its practicability towards RPME treatment. First-order kinetic model was used to clarify the behavior of RPME anaerobic digestion under different OLRs (0.14-4.00 g COD L -1  d -1 ) and HRT (1-7 d). The result shows that the highest COD removal efficiency and methane production rate were recorded to be 98.07% and 2.2223 L CH 4  d -1 , respectively. This result was further validated by evaluating the biokinetic coefficients (reaction rate constant ( k ) and maximum biogas production ( y m )), which gave values of k  = 0.57 d -1 and y m = 0.331 L d -1 . This kinetic data concludes that MAHB presented satisfactory performance towards COD removal with relatively high methane production, which can be further utilized as on-site energy supply.

Anaerobic digestion of alkaline kraft elemental chlorine-free bleaching wastewater in two mesophilic, lab-scale upflow anaerobic sludge bed reactors resulted in significantly higher biogas production (250±50 vs. 120±30 NmL g [Formula: see text]) and reduction of filtered total organic carbon (fTOC) (60±5 vs. 43±6%) for wastewater from processing of hardwood (HW) compared with softwood (SW). In all cases, the gas production was likely underestimated due to poor gas separation in the reactors. Despite changes in wastewater characteristics, a stable anaerobic process was maintained with hydraulic retention times (HRTs) between 7 and 14 h. Lowering the HRT (from 13.5 to 8.5 h) did not significantly affect the process, and the stable performance at 8.5 h leaves room for further decreases in HRT. The results show that this type of wastewater is suitable for a full-scale implementation, but the difference in methane potential between SW and HW is important to consider both regarding process dimensioning and biogas yield optimization.

The economics of Recycled Paper Sludge conversion into ethanol was here assessed with emphasis on integrating a cellulase recycling system. Without cellulases recycling this process presented positive economic outputs (payback period of 7.85 years; 10.90 Million US$ of accumulated NPV) despite the modest ethanol titers. Recycling both free and solid-bound enzymes allowed considerable savings of enzyme but also an increase on annual costs (0.88%), resulting on a superior economic output: payback period decreased to 7.25 years; accumulated NPV increased to 14.44 Million US$. Recycling exclusively the liquid fraction enabled a clear costs reduction, however, also total ethanol decreased, attenuating the abovementioned benefits. Targeting higher ethanol concentrations, superior solids consistencies were also evaluated. Despite a costs reduction, total ethanol decreased due to a higher ethanol retention on the solid. A sensitivity analysis further revealed that the cost of enzymes and ultrafiltration membrane may be critical on enzyme recycling economic feasibility., (Copyright © 2018 Elsevier Ltd. All rights reserved.)

We propose a novel approach to continuous bioprocessing of gases. A miniaturized, coated-paper strip, high gas fraction, biocomposite absorber has been developed using slowly shaken horizontal anaerobic tubes. Concentrated Clostridium ljungdahlii OTA1 was used as a model system. These gas absorbers demonstrate elevated CO mass transfer with low power input, reduced liquid requirements, elevated substrate consumption, and increased product secretion compared to shaken suspended cells. Concentrated OTA1 cell paste was coated by extrusion onto chromatography paper. The immobilized system shows high, constant reactivity immediately upon rehydration. Cell adhesion was by adsorption to the cellulose fibers; visualized by SEM. The C. ljungdahlii OTA1 coated paper mounted above the liquid level absorbs CO and H2 from a model syngas secreting acetate with minimal ethanol. At 100 rpm shaking speed (7.7 Wm(-3) ) the optimal cell loading is 6.5 gDCW m(-2) to maintain high CO absorbing reactivity without the cells coming off of the paper into the liquid phase. Reducing the medium volume from 10 mL to 4 mL (15% of tube volume) did not decrease CO reactivity. The reduced liquid volume increased secreted product concentration by 80%. The specific CO consumption by paper biocomposites was higher at all shaking frequencies <100 rpm than suspended cells under identical incubation conditions. At 25 rpm the biocomposite outperforms suspended cells for CO absorption by 2.5-fold, with an estimated power reduction of 97% over the power input at 100 rpm. The estimated minimum kL a for miniaturized biocomposite gas-absorbers is ∼100 h(-1) , 10 to 10(4) less power input than other syngas fermentation systems reported in the literature at similar kL a. Specific consumption rates in a biocomposite were ∼14 mmol gDCW-1 h(-1) . This work intensified CO absorption and reactivity by 14-fold to 94 mmol CO m(-2) h(-1) over previous C. ljungdahlii OTA1 work by our group. Specific acetate production rates were 23 mM h(-1) or 46 mmol m(-2) h(-1) . The specific rates and apparent kL a scaled linearly with biocomposite coating area. Biotechnol. Bioeng. 2016;113: 1913-1923. © 2016 Wiley Periodicals, Inc., (© 2016 Wiley Periodicals, Inc.)

There is an increasing worldwide demand for biogas. Anaerobic co-digestion involves the treatment of different substrates with the aim of improving the production of biogas and the stability of the process. This study evaluates how methane production is affected by the co-digestion of pig and dairy manure with grass silage and pulp and paper mill sludge and assesses whether methane production is affected by factors other than nutrient deficiency, low buffering capacity, inadequate dilution, and an insufficient activity and amount of microorganism culture. Anaerobic digestion was performed in batch reactors under mesophilic conditions for 20 days. The season of grass silage and manure collection proved to be an important factor affecting methane production. Spring grass silage produced a maximum of 250 mL/VSadded and spring manure 150 mL/VSadded, whereas autumn grass silage produced at most 140 ml/VSadded and autumn manure 45 mL/VSadded. The pulp mill sludge used is comprised of both primary and secondary sludge and produced at most 50 mL/VSadded regardless of season; this substrate benefitted most from co-digestion.

A novel electrohydrolysis pretreatment enhances methane production from lignocellulose material during anaerobic digestion. A biochemical methane potential assay was carried out to determine the effect of direct current and the efficacy of electrohydrolysis pretreatment on biogas production. Methane yield was increased by 13.8%, to 301 ± 3 mL CH 4 /g VS, when lignocellulosic waste was pretreated with electrohydrolysis. A net energy gain of 13,224 kJ was realized after electrohydrolysis pretreatment, which was 1.51 times higher than reported for thermal pretreatment. In addition, two kinetic models were used, including the modified Gompertz model to reproduce the experimental data. These finding support the potential for increased methane recovery from lignocellulosic waste using electrohydrolysis as a pretreatment., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

In the anaerobic digestion of lignocellulosic materials such as waste paper, the accessibility of microorganisms to the fermentable sugars is restricted by their complex structure. A mechanical pretreatment with a Hollander beater was assessed in order to reduce the biomass particle size and to increase the feedstock' specific surface area available to the microorganisms, and therefore improve the biogas yield. Pretreatment of paper waste for 60min improves the methane yield by 21%, from a value of 210ml/gVS corresponding to untreated paper waste to 254ml/gVS. 30min pretreatment have no significant effect on the methane yield. A response surface methodology was used to evaluate the effect of the beating time and feedstock/inoculum ratio on the methane yield. An optimum methane yield of 253ml/gVS was achieved at 55min of beating pretreatment and a F/I ratio of 0.3., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

The pulp and paper industry (PPI) has several opportunities to contribute to meeting prevailing climate targets. It can cut its own CO2 emissions, which currently account for 2% of global industrial fossil CO2 emissions, and it has an opportunity to produce renewable energy, fuels, and materials for other sectors. The purpose of this study is to improve understanding of the decarbonization prospects of the PPI. The study provides insights on the magnitude of needed annual renewal rates for several possible net-zero target years of industrial fossil CO2 emissions in the PPI and discusses decarbonization opportunities, namely, energy and material efficiency improvement, fuel switching, electrification, renewable energy production, carbon capture, and new products. The effects of climate policies on the decarbonization opportunities are critically evaluated to provide an overview of the current and future business environment of the European PPI. The focus is on Europe, but other regions are analyzed briefly to widen the view. The analysis shows that there are no major technical barriers to the fossil-free operation of the PPI, but the sector renovates slowly, and many new opportunities are not implemented on a large scale due to immature technology, poor economic feasibility, or unclear political environment. [ABSTRACT FROM AUTHOR]

The present work introduces the study of the CO2 capture process by zeolites synthesized from paper sludge and scrap glass. Zeolites ZSM-5, analcime and wairakite were produced by means of two types of Structure Directing Agents (SDA): tetrapropilamonium (TPA) and ethanol. On the one hand, zeolite ZSM-5 was synthesized using TPA; on the other hand, analcime and wairakite were produced with ethanol. The temperature programmed desorption (TPD) technique was performed for determining the CO2 sorption capacity of these zeolites at two sorption temperatures: 50 and 100 °C. CO2 sorption capacity of zeolite ZSM-5 synthesized at 50 °C was 0.683 mmol/g representing 38.2% of the value measured for a zeolite ZSM-5 commercial. Zeolite analcime showed a higher CO2 sorption capacity (1.698 mmol/g) at 50 °C and its regeneration temperature was relatively low. Zeolites synthesized in this study can be used in the purification of biogas and this will produce energy without increasing the atmospheric CO2 concentrations., (© The Author(s) 2014.)

The present work deals with intensification of bioethanol production from waste newspaper using Saccharomyces cerevisiae using ultrasonic irradiations. The effect of different process parameters such as application of ultrasonic irradiation at different growth phases, irradiation time, ultrasonic power and duty cycle on the bioethanol production has been investigated. The favorable conditions for the maximum yield were established as application of ultrasonic irradiation (duration of 10 min) to fermentation broth at 12 h of growth phase with 25 kHz frequency, 160 W power and 20% duty cycle. The bioethanol productivity was increased by 1.8 times from 7.8 to 14.1 g/L compared with the non-sonicated control fermentation. Decrease in glucose concentration from 0.63% to 0.2% w/v in ultrasound-assisted fermentation confirmed the improved substrate uptake of the microbial cell due to the application of ultrasound. ESEM analysis also confirmed the changes in the cell morphology leading to improved cell permeability. Results were fitted to an unstructured kinetic model comprising of the kinetic and physiological parameters. Overall, the work has demonstrated an intensified approach for the bioethanol production based on the use of ultrasound., (Copyright © 2015 Elsevier B.V. All rights reserved.)

This study aims to underline the huge potential in Canada of adding value to cardboard and compost as a renewable fuel with a low ecological footprint. The slow pyrolysis process of lined cardboard and compost blend was investigated. Thermal behavior was investigated by thermogravimetric analysis coupled with mass spectrometry (TGA-MS). The thermal profiles are presented in the form of TGA/DTG curves. With a constant heating rate of 10 °C/min, two parameters, temperature and time were varied. Cardboard decomposition occurred mostly between 203 °C and 436 °C, where 77% of the sample weight was decomposed. Compost blend decomposition occurred mostly between 209 °C and 373 °C, with 23% of weight. The principal gaseous products that evolved during the pyrolysis were H2O, CO and CO2. As a result, slow pyrolysis led to the formation of biochar. High yield of biochar from cardboard was found at 250 °C for a duration of 60 min (87.5%) while the biochar yield from the compost blend was maintained constant at about 31%. Finally, kinetic parameters and a statistical analysis for the pyrolysis process of the cardboard and compost samples have been investigated. Both materials showed a favorable thermochemical behavior. However, unlike cardboard, compost pyrolysis does not seem a promising process because of the low superior calorific and biochar values., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Paper and pulp mills generate substantial quantities of cellulose-rich sludge materials that are disposed in landfills at a large scale. For sustainability purposes, sludge materials can be bioprocessed to produce renewable fuels and useful chemicals. The enzymatic hydrolysis of cellulose is the process bottleneck that affects the conversion economics directly by using zero-cost raw materials. In order to study and optimize the process, the characteristics of the sludge raw materials should be first evaluated. In this work, sludge samples were obtained from paper mills located at different locations in Wisconsin and Minnesota. Part of the sludge samples was washed (de-ashed) with hydrochloric acid while the other part remained unwashed. The samples were subjected to multiple spectroscopic analyses techniques to evaluate the morphological properties of cellulose fibers and to estimate the total structural carbohydrate content. The results showed that the de-ashing process changed some fiber characteristics and cellulose crystallinity structure in all sludge samples. Sludge sample A (obtained from Kraft pulp and recycled paper mill region) showed a high percentage of fiber, with crystalline cellulose, compared to the other two sludge samples suggesting that sludge A is a valuable source to make value-added products. Aspen Plus mass and energy calculations performed in view of the 'zero' cost and the reliable supply of sludge raw materials producing 2 mol H 2 /mol glucose. Moreover, the results showed that extracting crystalline cellulose from these sludge samples is more profitable than crystalline cellulose made from the other lignocellulosic feedstocks. The results reported here showed that the utilization of these sludge materials would be an economically attractive and promising alternative for the production of hydrogen. Image 1 • A new method for paper mill sludge (PMS) characterization as renewable feedstock. • The deashing step has a major effect on the bioconversion of the PMS. • Studying the crystalline cellulose of the PMS. • A relation between the characterization and potential sugar yield was established. [ABSTRACT FROM AUTHOR]

Summary: A novel bioprocess design to convert paper mill sludge (PMS) to biofuels is proposed in this work. The design utilizes cellulosic fiber recovered from the PMS via optimized de‐ashing (HCl washing) step. This work specifically provided a technical and economic analysis of paper mill sludge conversion into biofuel production using a novel protocol. The protocol is based on scanning electron microscopy (SEM) analysis to assess the quality of the contained cellulose prior to further processing. The results are crucially important to determine the suitability of the PMS feedstock to produce biofuels. SEM analysis was employed as a preliminary screening tool to evaluate sludge digestibility and conversion. The SEM characterization technique established a direct relationship between the fiber morphology, presence of crystals salts and sugar yield after enzymatic hydrolysis. Substantial structural changes were observed before and after de‐ashing the sludge samples, leading to a correlation between the surface morphology and the washing step. The results suggested that de‐ashing changes the surface morphology and upon analysis, increased the sugar yield up to about 86% as opposed to 2.2% in sludge sample A as an example. The PMS conversion into biofuel was simulated using Aspen PLUS and compared to a similar process using corn stover as feedstock. The simulation results showed it is 20% cheaper to produce bioethanol from PMS compared to corn stover. The simulation revealed less energy demand by around 13 320 MJ/h compared to that when corn stover was used. [ABSTRACT FROM AUTHOR]

This paper presents the development and evaluation of three fuzzy neural network (FNN) models for a full-scale anaerobic digestion system treating paper-mill wastewater. The aim was the investigation of feasibility of the approach-based control system for the prediction of effluent quality and biogas production from an internal circulation (IC) anaerobic reactor system. To improve FNN performance, fuzzy subtractive clustering was used to identify model's architecture and optimize fuzzy rule, and a total of 5 rules were extracted in the IF-THEN format. Findings of this study clearly indicated that, compared to NN models, FNN models had smaller RMSE and MAPE as well as bigger R for the testing datasets than NN models. The proposed FNN model produced smaller deviations and exhibited a superior predictive performance on forecasting of both effluent quality and biogas (methane) production rates with satisfactory determination coefficients greater than 0.90. From the results, it was concluded that FNN modeling could be applied in IC anaerobic reactor for predicting the biodegradation and biogas production using paper-mill wastewater.

An innovative circular economy (CE) system was implemented at the wastewater treatment plant (WWTP) in Brunswick. The performance of the CE system was evaluated for 4 years: the thermal pressure hydrolysis enhanced the methane production by 18% and increased the digestate dewaterability by 14%. Refractory COD formed in thermal hydrolysis and increased the COD concentration in the WWTP effluent by 4 mg L -1 while still complying with the legal threshold. Struvite production reached high phosphorus recovery rates of >80% with a Mg:P molar ratio ≥0.8. Nitrogen was successfully recovered as ammonium sulfate with high recovery rates of 85-97%. The chemical analyses of secondary fertilizers showed a low pollutant content, posing low risks to soil and groundwater ecosystems. The total carbon footprint of the WWTP decreased due to enhanced biogas production, the recovery of renewable fertilizers and a further reduction of nitrous oxide emissions. Using green energy will be crucial to reach carbon neutrality for the entire WWTP., Competing Interests: The authors declare there is no conflict., (© 2024 The Authors This is an Open Access article distributed under the terms of the Creative Commons Attribution Licence (CC BY 4.0), which permits copying, adaptation and redistribution, provided the original work is properly cited (http://creativecommons.org/licenses/by/4.0/).)

With increasing demand of fossil fuels and water pollution and their environmental impacts, marine green microalgae have gained special attention in both scientific and industrial  fields. This is due to their fast growth in non-arable lands with high photosynthetic activity, their metabolic plasticity, as well as their high CO 2 capture capacity. Tetraselmis species, green and eukaryotic microalgae, are not only considered as a valuable source of biomolecules including pigments, lipids, and starch but also widely used in biotechnological applications. Tetraselmis cultivation for high-value biomolecules and industrial use was demonstrated to be a non-cost-effective strategy because of its low demand in nutrients, such as phosphorus and nitrogen. Recently, phycoremediation of wastewater rich in nutrients, chemicals, and heavy metals has become an efficient and economic-alternative that allows the detoxification of waters and induces mechanisms in algal cells for biomolecules rich-energy synthesis to regulate their metabolic pathways. This review aims to shed light on Tetraselmis species for their different culture conditions and metabolites bioaccumulation, as well as their human health and environmental applications. Additionally, phycoremediation of contaminants associated to biofuel production in Tetraselmis cells and their different intracellular and extracellular mechanisms have also been investigated., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

The present investigation has evaluated the use of effluents from a secondary municipal wastewater treatment plant for biomass production and potential of the biomass for biodiesel production. Cultivations of Chlorella vulgaris using wastewater, wastewater with supplementation, and WC medium were carried out. Effect of wastewater collected in different months on biomass productivity (BP) and lipid composition was studied. Methods based on NMR and GC-MS techniques were applied for determining the composition of the lipids and their fatty acid profile including poly unsaturated fatty acids (PUFAs). Lipids extracted are comprised of both neutral (tri acyl glycerides, TAG; free fatty acids, FFA) and polar (glyco glycero/phospho) lipids. The TAG content of the extracted lipids was determined in the range of 22.5-41.3% w/w. The NMR and GC-MS compositional results of microalgal lipids of biomasses cultivated in wastewater without nutrient supplementation, collected in different months, showed potential for biodiesel production. The fatty acid profiles of neutral and polar lipids, which are mainly comprised of saturated and unsaturated long alkyl chain (C16-C22) fatty acids, are potential sources for the biodiesel and food industry. The concentration of nitrates (45-78 mg L -1 ) in wastewater without supplementation, collected in different months, was found to be optimum to enable cultivation of biomasses with reasonably good BP of 21.5-28.1 mg L -1  day -1 . Similar results have been obtained in the present work as well as reported in the literature in the case of WC medium (nitrate, 69 mg L -1 ) with BP of 25.5-28.2 mg L -1  day -1 , thus highlighted the significance of the presented work., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Renewable and sustainable biofuel production, such as biobutanol, is becoming increasingly popular as a substitute for non-renewable and depleted petrol fuel. Many researchers have studied how to produce butanol cheaply by considering appropriate feedstock materials and bioprocess technologies. The production of biobutanol through acetone-butanol-ethanol (ABE) is highly sought after around the world because of its sustainable supply and lack of competition with food. The purpose of this study is to present the current biobutanol production research and to analyse the biobutanol research conducted during 2006 to 2023. The keyword used in this study is "Biobutanol," and the relevant data was extracted from the Web of Science database (WoS). According to the results, institutions and scholars from the People's Republic of China, the USA, and India have the highest number of cited papers across a broad spectrum of topics including acetone-butanol-ethanol (ABE) fermentation, biobutanol, various pretreatment techniques, and pervaporation. The success of biobutanol fermentation from biomass depends on the ability of the fermentation operation to match the microbial behaviour along with the appropriate bioprocessing strategies to improve the entire process to be suitable for industrial scale. Based on the review data, we will look at the biobutanol technologies and appropriate strategies that have been developed to improve biobutanol production from renewable biomass., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

The use of nanomaterials in biofuel production from lignocellulosic biomass offers a promising approach to simultaneously address environmental sustainability and economic viability. This review provides an overview of the environmental and economic implications of integrating nanotechnology into biofuel production from low-cost lignocellulosic biomass. In this review, we highlight the potential benefits and challenges of nano-based biofuel production. Nanomaterials provide opportunities to improve feedstock pretreatment, enzymatic hydrolysis, fermentation, and catalysis, resulting in enhanced process efficiency, lower energy consumption, and reduced environmental impact. Conducting life cycle assessments is crucial for evaluating the overall environmental footprint of biofuel production. An economic perspective that focuses on the cost implications of utilizing nanomaterials in biofuel production is also discussed. A comprehensive understanding of both environmental and economic dimensions is essential to fully harness the potential of nanomaterials in biofuel production from lignocellulosic biomass and to move towards sustainable future energy., (© 2024. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Management of municipal solid waste is an efficient method to increase resource efficiency, as well as to replace fossil fuels with renewable energy sources due to that (1) waste to a large extent is renewable as it consists of food waste, paper, wood etc. and (2) when energy and materials are recovered from waste treatment, fossil fuels can be substituted. In this paper results from a comprehensive system study of future biological treatment of readily degradable waste in two Swedish regions are presented. Different collection and separation systems for food waste in households have been applied as well as technical improvements of the biogas process as to reduce environmental impact. The results show that central sorting of a mixed fraction into recyclables, combustibles, biowaste and inert is a competitive option compared to source separation. Use of pellets is beneficial compared to direct spreading as fertiliser. Fuel pellets seem to be the most favourable option, which to a large extent depends on the circumstances in the energy system. Separation and utilisation of nitrogen in the wet part of the digestion residue is made possible with a number of technologies which decreases environmental impact drastically, however to a substantial cost in some cases., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

This paper evaluates the implementation of three waste-to-energy projects at the University of Cincinnati: waste cooking oil-to-biodiesel, waste paper-to-fuel pellets and food waste-to-biogas, respectively. The implementation of these waste-to-energy (WTE) projects would lead to the improvement of campus sustainability by minimizing waste management efforts and reducing GHG emissions via the displacement of fossil fuel usage. Technical and economic aspects of their implementation were assessed and the corresponding GHG reduction was estimated. Results showed that on-site implementation of these projects would: (1) divert 3682L (974 gallons) of waste cooking oil to 3712L (982 gallons) of biodiesel; (2) produce 138tonnes of fuel pellets from 133tonnes of waste paper (with the addition of 20.75tonnes of plastics) to replace121tonnes of coal; and (3) produce biogas that would be enough to replace 12,767m(3) natural gas every year from 146tonnes of food waste. The economic analysis determined that the payback periods for the three projects would be 16months for the biodiesel, 155months for the fuel pellet, and 74months for the biogas projects. The reduction of GHG emission from the implementation of the three WTE projects was determined to be 9.37 (biodiesel), 260.49 (fuel pellets), and 11.36 (biogas) tonnes of CO2-eq per year, respectively., (Copyright © 2015 Elsevier Ltd. All rights reserved.)

Transforming plant biomass to biofuel is one of the few solutions that can truly sustain mankind's long-term needs for liquid transportation fuel with minimized environmental impact. However, despite decades of effort, commercial development of biomass-to-biofuel conversion processes is still not an economically viable proposition. Identifying value-added co-products along with the production of biofuel provides a key solution to overcoming this economic barrier. Lignin is the second most abundant component next to cellulose in almost all plant biomass; the emerging biomass refinery industry will inevitably generate an enormous amount of lignin. Development of selective biorefinery lignin-to-bioproducts conversion processes will play a pivotal role in significantly improving the economic feasibility and sustainability of biofuel production from renewable biomass. The urgency and importance of this endeavor has been increasingly recognized in the last few years. This paper reviews state-of-the-art oxidative lignin depolymerization chemistries employed in the papermaking process and oxidative catalysts that can be applied to biorefinery lignin to produce platform chemicals including phenolic compounds, dicarboxylic acids, and quinones in high selectivity and yield. The potential synergies of integrating new catalysts with commercial delignification chemistries are discussed. We hope the information will build on the existing body of knowledge to provide new insights towards developing practical and commercially viable lignin conversion technologies, enabling sustainable biofuel production from lignocellulosic biomass to be competitive with fossil fuel., (© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Herbal waste produced during the manufacturing of herbal products is a potential feedstock for anaerobic digestion due to high amount of organic matter that can be transformed into biogas as an energy resource. Therefore, the present study was undertaken to convert herbal waste produced during the manufacturing of common of Ayurveda products into biogas through anaerobic digestion process using batch test study under controlled mesophilic temperature conditions of 35 °C with food to inoculum ratio of 0.75. The maximum biomethane potential (BMP) of 0.90 (gCH 4 COD/g COD fed ) and sludge activity of 0.70 (gCH 4 -CD/gVSS) was exhibited by WS herbal waste owing to its high chemical oxygen demand (COD) of 4 g/g and better solubilization potential of the organic matter showing change in volatile suspended solids (ΔVSS) of 79%. On the other hand, the waste derived from the TA herb, exhibited the least biogas yield of 0.55 (gCH 4 COD/g COD fed ) and sludge activity of 0.40 (gCH 4 -CD/gVSS), albeit with higher organic matter present. This was due to the possible hindrance of waste solubilization by the presence of lignin. The waste derived from VVL and PE showed intermediate BMP and sludge activity. The methane generation rate constant (k), a key indicator of the biodegradation potential, was also evaluated. The k values showed similar trend as of BMP values ranging from 0.081 to 0.15 d -1 thus indicating the influence of presence of lignin and the change in ΔVSS. The present study proves anaerobic digestion to be an alternative treatment method to be a milestone for management of herbal wastes and can be successfully implemented on real-scale systems., (© 2024. The Author(s), under exclusive licence to Springer Nature Switzerland AG.)

The organic wastes and residues generated from agricultural, industrial, and domestic activities have the potential to be converted to bioenergy. One such energy is biogas, which has already been included in rural areas as an alternative cooking energy source and agricultural activities. It is produced via anaerobic digestion of a wide range of organic nutrient sources and is an essential renewable energy source. The factors influencing biogas yield, i.e., the various substrate, their characteristics, pretreatment methods involved, different microbial types, sources, and inoculum properties, are analyzed. Furthermore, the optimization of these parameters, along with fermentation media optimization, such as optimum pH, temperature, and anaerobic digestion strategies, is discussed. Novel approaches of bioaugmentation, co-digestion, phase separation, co-supplementation, nanotechnology, and biorefinery approach have also been explored for biogas production. Finally, the current challenges and prospects of the process are discussed in the review., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

Anaerobic treatment of oily substrate, known as grease trap waste (GTW), was investigated for its practicability via continuous stirred tank reactor (CSTR) at different operating conditions and selected recovery strategies of feeding frequency efficacy. This study determine the performance of feeding frequency efficacy, namely feeding every 24 hours (R 24H ) and feeding every 12 hours (R 12H ). Under organic loading rate (OLR) of 2.2 gCOD/L.day, R 12H exhibited methane composition of 57%, methane production rate of 0.27 LCH 4 /L.day, and methane yield of 0.14 LCH 4 /gCOD removed . At the same OLR, R 24H recorded methane composition of 60%, methane production rate of 0.29 LCH 4 /L.day and similar methane yield as R 12H . Findings indicated that R 24H showed performance comparable to that of R 12H . Given minor variation observed in performance, it is recommended that plant operators may consider scheduling two feedings per day for low loading conditions and switch to one feeding per day for higher loading conditions. This strategy is designed to balance the system and prevent shock loads, which could lead to plant shutdowns. This mechanism will induce their conversion to volatile fatty acids (VFAs); thus, reducing the risk of acid accumulation and pH drops, which could inhibit methanogens to produce methane, especially for oily substrate., Competing Interests: The authors declare there is no conflict., (© 2024 The Authors This is an Open Access article distributed under the terms of the Creative Commons Attribution Licence (CC BY-NC-ND 4.0), which permits copying and redistribution for non-commercial purposes with no derivatives, provided the original work is properly cited (http://creativecommons.org/licenses/by-nc-nd/4.0/).)

The biomass content of material from pulp and paper production (a mixture of waste and paper and thin layer packaging plastics) is determined by the adapted balance method. This novel approach is a combination of combustion elemental analysis (CHNSO) and a data reconciliation algorithm based on successive linearisation for evaluation of the analysis results. It also involves less effort and expense than conventional procedures. However, the CHNSO technique only handles small mass amounts (few hundred milligrams), so cryogenic impact milling was applied for particle size reduction below 200 µm in order to generate homogeneous, representative analysis samples. The investigation focuses on the parameters biogenic content as a percentage of the total mass xB and xB (TC), which is the biomass stated as a fraction of the total carbon value. The results are within 1%-5% of the data obtained by the reference methods, namely the selective dissolution method and (14)C- method. Additionally, advantages and drawbacks of the adapted balance method in comparison with standard methods are discussed, showing that the adapted balance method is a method to be considered for the determination of biomass content in solid recovered fuels or similar materials., (© The Author(s) 2014.)

Fibres fractionated from solid recovered fuel (SRF), a standardised market combustion fuel produced from sorted waste, were considered as a source of lignocellulosic fermentable sugars. The fibre yield from four samples of SRF was 25-45%, and the separated material consisted of 52-54% carbohydrates, mainly glucan, with a high content of ash (12-17%). The enzymatic digestibility of recovered fibres was studied at low and high solids loading and compared with model substrates containing only chemical and mechanical pulps. Above 80% hydrolysis yield was reached at 20% solids loading in 48 h, but variation was observed between different samples of recovered fibres. Surfactants were found to improve the hydrolysis yield of recovered fibres especially in tumbling-type of mixing at low solids loading, where hydrolysis was found to stagnate without surfactants. The results suggest that SRF is a potential source of easily digestible lignocellulosic carbohydrates for use in biorefineries., (Copyright © 2014 Elsevier Ltd. All rights reserved.)