Search

The failure mode is a dominant factor of mechanical performance of braided composite tube subjected to axial compression. The failure mode was modified by tailoring stack-up sequence of composite tubes hybridized by bi/tri-axial braided laminate. The thermal photographing and micro-CT scanning methods were employed to monitor the in-situ damage progression and post-mortem specimen, respectively. The results show that the delamination was easy to be induced at the interface nearby tri-axial braided laminate. It attributes to the combination between the crack caused by local buckling of the axial yarns and the crack caused by shear deformation of braiding yarns. By the illumination of this behavior, delamination is controlled to occur at the different position along thickness direction of braided tube by adjusting the stacking sequence of braided laminates. When delamination position transfer from the inner/outer sides to the middle of tube wall, the failure mode transfer from the progressive folding to splaying, which increase the specific energy absorption by 45.77%. [ABSTRACT FROM AUTHOR]

• The usage of correlation between maximum temperature and peak load. • The reconstruction of CT images identifies the debonding distribution and degree. • A novel inspection way of combing infrared imaging and micro CT reconstruction methods. • The role of axial yarns in axial crushing. In this work, the effect of axial yarns on damage behavior of two-dimensional triaxially braided composite(2DTBC) tubes subjected to axial compression was investigated. A novel damage detection method combining infrared thermography and CT scanning was presented. In the area without axial yarns, yarn crossovers were separated from each other due to interlacing patterns. Axial compression caused the braiding yarns to shear deformation like scissors. Inter-yarn de-bonding appeared in crossovers and could not connect. Consequently, it caused a progressively folding failure mode. In contrast, local buckling occurred on axial yarns because of their primary loading behavior. Cracks along the axial yarns formed, which would combine with debonding crossovers caused by the sheared braiding yarn. It resulted in significant inter-layer delamination and consequently splaying failure mode. The energy absorption of composites tube with 18 axial yarns increased by 79.9% at the cost of 27.8% fiber usage more than 3 axial yarns. [ABSTRACT FROM AUTHOR]

Localized deformation and damage mechanism of triaxial braided composite tubes, with different quantities and positions of axial yarns, were experimentally studied under transverse low-velocity impact. A high-speed infrared thermography was applied to analyze the transient thermo-mechanical failure process and afterwards verified by the external and internal damage characterization. It is found that the distribution of axial yarns has a significant effect on the mechanical behavior of braided composite tubes. The bending stiffness and peak force of the tubes were enhanced with the increased quantity of axial yarns, while the impact lasting time and displacement presented an opposite trend. And the more axial yarns assembled at the impact side, the greater force oscillatory of the tubes under low-velocity impact, accompanied by the decreased heat generation in small-angle braided tubes and the alleviated fiber tows fracture, delamination and in-plane shear cracks inside the wall of large-angle braided tubes. On the premise of the same quantity of axial yarns, the position effect plays a key role. Axial yarns concentrated at the impact side could restrain the damages spreading to the non-impact side by changing the damage mode of large-angle braided tubes. If a larger force is needed at the early stage, axial yarns could be inserted at the local position most probably to be impacted; Otherwise, it is highly suggested to braid at least one axial yarn in each layer at the impact side and non-impact side respectively to reinforce localized strength and prevent the impact-side indentation and non-impact-side delamination. • High-speed IR thermography verified by the external and internal damage characterization. • Effect of axial yarn quantity and location on mechanical behavior and damage mechanism. • Force oscillation response caused by dense distribution of axial yarns at the impact side. • Necessity of axial yarns in alleviating the severity of localized damages at the impact side. • Importance to install at least one axial yarn at the non-impact side of large-angle braided tube. [ABSTRACT FROM AUTHOR]

To meet the demand of lightweight truss, thin-walled single-/double-/four-cell carbon fiber reinforced polymethacrylimide foam sandwich composite beams were manufactured by tubular braiding. Transverse impact damage and axial compression failure of the braided sandwich beams were investigated by finite element modeling, micro-CT detection, acoustic emission and infrared imaging characterization. It is found that impact damage concentrated at edges of the indentation region, internal CFRP walls and surrounding foams. Different from the continuous vertical wall in double-cell beam, cracks on the internal vertical wall of four-cell beam were suppressed at half height due to the discontinuous horizontal wall. During the axial compression, six failure modes were observed for non-impacted(0J) and impacted(40J, 60J, 80J) specimens, which were determined by the combined effect of impacted damages and inner configurations. And the inner configurations have an advantage over the transverse impact effect on the axial failure mechanism. Unlike the single-cell beams, the double- and four-cell counterparts did not present buckling or bending failures owing to the effective support from internal CFRP walls, however, more significant fracture was found at their outer CFRP layers due to the progressive mechanism of shear, tearing, splaying, and separation. • Integral braiding and net forming of sandwich beams with complex cross sections. • Mutual verification by micro-CT, FE analysis, and morphology characterization. • Real-time failure analysis by joint application of AE and IR method. • Effect of pre-impact and inner configurations on CAI properties of sandwich beams. [ABSTRACT FROM AUTHOR]