Search

When designing solid-state Marx modulators (SSMMs) with fast-rising nanosecond pulses, the gate-driving scheme for pulse discharge switches is one of the most important aspects to be considered. In this article, we propose a nanosecond current-loop gate-driving circuit for a synchronized fast gate drive of pulse discharge switches. The proposed circuit comprises an inverter, a current-loop cable, and discharge switch drivers. The inverter generates bipolar pulses that simultaneously provide driving power and fast triggering signals to all discharge switch drivers through the cable. The triggered discharge switch drivers rapidly turn on/off all discharge switches with accurate synchronization. In the inverter and discharge switch drivers, the fast gate-driving methods were used to overcome parasitic inductances and realize nanosecond operation. The concept and operational principles of the proposed gate-driving scheme are presented. To validate the performance and reliability of the SSMM using the proposed current-loop gate-driving circuit, a laboratory test on a 10-kV–70-A–50-kHz SSMM prototype was conducted, and the results were discussed. [ABSTRACT FROM AUTHOR]

This paper describes a study on the high-voltage compact solid-state pulsed-power modulator for parallel reactor operation. The current capacity of the pulsed modulator has been improved to drive multiple reactors in parallel. The pulse discharge switch uses the IXYK120N120C3 (1200 V/120 A) insulated-gate bipolar transistor for a high current output. The gate driver has been improved according to the characteristics of the replaced switch. The output specifications of the modified pulsed-power modulator are a maximum output voltage of 40 kV, a maximum output current of 300 A, a pulsewidth ranging from 1.5 to $5~\mu \text{s}$ , a maximum repetition rate of 3 kHz, and an average power of 13 kW. The modulator has the dimensions of $450 \times 475 \times 600$ mm3, a maximum peak power of 12 MW, and a maximum power density of 93 kW/L. A resistive load experiment and a plasma reactor parallel drive test were performed. Four parallel reactors were driven using one modulator. In addition, a 50% reduction in the concentration of toluene was obtained through the experiment of the toluene gas treatment using only parallel plasma reactors. [ABSTRACT FROM AUTHOR]

Conventional power supply systems for xenon lamps have only limited applicability in sintering, because sintering needs to drive the lamp itself as well as enable instantaneous and strong discharge of voltage and current for generating intense light. This implies that, for sintering applications, a method should be developed that would enable instantaneous and strong discharge of energy. In this paper, we propose a new xenon lamp sintering system with an additional capacitor charger and bank. The proposed system features three power supplies. Two power supplies, called the trigger and the simmer, ionize gaseous xenon using a 23-kV trigger pulse output and sustain the ionized xenon gas using a 2.5-kW simmer power supply. The used trigger is also specially designed to conduct high current through its transformer, and it makes the proposed system an outstanding high voltage blocking capability. Another 36-kW power supply charges a 130-mF capacitor bank with a high-efficiency resonant converter. In addition, some components such as the simmer blocking diode and the trigger output capacitor are introduced, because combining different power supplies causes operational problems. These components are analyzed with some circuits that show its features, and finally, the validity of the suggested system was confirmed in two steps. First, the simmer power supply and the capacitor charger were tested for the rated operating performance by using a resistive load condition. As a result, the rated operation of the simmer power supply was confirmed under the 2.5-kW output condition, and the efficiency of the capacitor charger was found to be greater than 96% at the rated 36-kW rated load condition. In addition, a pulse discharge current of 900 A was also observed with the equivalent resistor load through a pulsed discharge experiment of the capacitor bank, which was charged at 1500 V. The trigger power supply, whose equivalent resistive load was difficult to realize, was experimented directly using the real xenon lamp to check the stable trigger operation of the xenon lamp at its 23-kV output pulse voltage. After the verification using the resistive load condition, the real operation and performance of the combined xenon lamp power supply system that includes three kinds of power supplies were finally tested and verified by using the actual xenon lamp as a total system. [ABSTRACT FROM AUTHOR]

Ship building companies are exposed to increasingly strict regulations on exhaust air from painting facilities, which current exhaust air treatment methods cannot adequately meet. We propose the use of a plasma system using a pulsed-power supply, which we constructed and tested at the painting facility of a ship building factory. Through gas chromatography and facility efficiency analysis, we found flexibility in design of the plasma system. We demonstrate the efficiency and safety of our plasma system, and emphasize the importance of posttreatment facilities for the secondary pollutant treatment. [ABSTRACT FROM AUTHOR]

This paper describes a high-frequency pulsed-power generator for various industrial applications such as water treatment, food and medical apparatus for sterilization, or polluted gas treatment. The system is made of silicon-controlled rectifier as a main trigger switch, capacitors, two-stage magnetic pulse compression stages, and a linear transformer to generate a maximum of 120-kV, 5-kA pulse. The parameters obtained through the development are: output voltage: 120 kV (maximum), pulse repetition ration: 300 pulse per second, pulsewidth: 0.25~\mu \texts , and mean power: 30 kW. The designed pulsed-power generator is confirmed to be used effectively for many high-voltage pulsed-power applications related to environmental industry by simulation and experiments. [ABSTRACT FROM AUTHOR]