Search

This paper presents a methodology that allows for calculating the thermal and electric energy consumption together with CO2 emissions of cities by inhabitant and household based on climate, only making use of publicly available data. With this aim, climate was analysed and cities were classified based on it. The analysis of those cities' energy consumption and CO2 emissions allowed for drawing conclusions. Once aware of the climate zones in which energy consumption and emissions are higher, these mentioned conclusions could help to take further actions. An index has been defined to facilitate this analysis. This paper shows the case of Spain for illustrative purposes. This type of study has been carried out in some detail in many countries, but not in Spain yet. This paper tries as well to fill the existing gaps in studies that relate climate to thermal and electric energy consumption. For this purpose, it analyses the 145 cities in Spain that have more than 50,000 inhabitants. Knowing all this is essential in all regions and countries. It will allow for taking proper actions for promoting the energy saving and the use of alternative energy sources that reduce CO2 emissions. According to the study carried out in this paper, the extremer the climate of a city is, the higher the thermal energy consumption is. This consumption decreases in softer climates. However, electric energy consumption is similar in all cities independent of the climate they have. With regard to CO2 emissions, it was calculated that the higher the energy consumption of a city is, the higher these emissions are. [ABSTRACT FROM AUTHOR]

The trend in energy consumption, with a particular focus on heating and cooling demand, is an issue that is relevant to the promotion of new energy policies and more efficient energy systems. Moreover, heating and cooling energy demand is expected to rise in the next several decades, mainly due to climate change as well as increasing incomes in developing countries. In this context, the building sector is currently a relevant energy-intensive economic sector in Morocco; it accounts for 33% of the country's total energy demand (as the sector with the second highest energy demand, after the transport sector), with the residential sector accounting for 25% and the tertiary sector accounting for 8%. Aiming to reduce energy dependence and promote sustainable development, the Moroccan government recently issued a comprehensive plan to increase the share of renewables and improve energy efficiency. This strategy includes novel thermal building regulations promoted by the Moroccan Agency for Energy Efficiency. This paper analyzes the thermal behavior and heating-cooling energy demand of a residential building located in Tangier (Morocco) as a case example, based on the country's new thermal regulations and considering specific climatological conditions. A comparison with common Moroccan residential buildings as well as with those in nearby countries with similar meteorological conditions but significant differences in terms of energy demand regulation and requirements, such as Spain, is also included. Simulations were carried out using the DesingBuilder and EnergyPlus Software packages. According to the results, the last building thermal regulation requirements in Morocco need to be revised and extended in order to achieve the energy efficiency objectives established by the Moroccan government for 2030. [ABSTRACT FROM AUTHOR]

The use of lightweight concrete for the construction of single-family houses has become increasingly popular in Spain. In this paper, single-family houses with different shape factors and window-to-wall ratios are analysed from both a thermal and environmental perspective using Passive House Planning Package (PHPP) software to calculate the energy demand. The study has been carried out for different Atlantic microclimates (coastal, inland, and mountain) in northern Spain. What most affects the thermal energy used for air conditioning is the variation of the microclimates, so the study focuses mainly on this aspect. Operational energy for heating has decreased greatly via the use of high degree of insulation and hence the next task is to decrease the total energy consumed taking into account the embodied energy. Impacts on Primary Energy and Global Warming Potential are calculated using a cradle-to-grave approach. The energy use for heating and domestic hot water is analysed for different thicknesses of insulation under three energy supply scenarios: electricity only (for 2018 and with the Spanish decarbonisation plan for 2030); heat pump plus electricity; and natural gas boiler. Even for houses with a good level of insulation, the ratio of operational-to-total impacts varies significantly: from 46% to 87% for primary energy and from 31% to 75% for global warming potential, depending on the shape factor of the house, the microclimate and the heat supply scenario. By applying future environmental policies, electricity can become a more environmentally friendly option than natural gas. [ABSTRACT FROM AUTHOR]

Rooftop gardens ona building have proved to be a good way to improve its storm water management, but many other benefits can be obtained from the installation of these systems, such as reduction of energy consumption, decrease of the heat stress, abatement on CO2 emissions, etc. In this paper, the effect from the presence of these rooftop gardens on abuilding's energy consumption has been investigated by experimental campaigns using a green roof ona public building in a Mediterranean location in Spain. The obtained results demonstrate a substantial improvement by the installation of the green roof onthe building's cooling energy demand for a standard summer day, in the order of 30%, and a reduction, about 15%, in the heating energy demand for a winter day. Thus, given the longer duration of the summer conditions along the year, a noticeable reduction on energy demand could be obtained. Simulation analysis, using commercial software TRNSYS code, previously calibrated using experimental data for typical summer and winter days, allows for the extrapolation to the entire year of these results deducing noticeable improvement in energy efficiency, in the order of 19%, but with an increase of 6% in the peak power during the winter period. [ABSTRACT FROM AUTHOR]

Many studies are nowadays focused on the application of energy conservation measures (ECMs) to building sector because of the reductions of both greenhouse gases and energy consumption set by the European Union. Heating, Ventilating and Air Conditioning (HVAC) systems are the main causes of most energy consumption in the existing buildings. One of the methods to reduce energy consumption is the modification of setpoint temperatures adapted to external climate conditions but maintaining acceptable comfort levels. The adaptive comfort model of ASHRAE 55–2017 uses the prevailing mean outdoor temperature, which records temperatures of the previous days weighted by a constant α which depends on weather changes. This paper analyses the possibilities of optimizing building energy saving with setpoint temperatures according to the α-value and the number of previous days considered. A total of 390 simulations were conducted by considering three representative climate zones of Spain. The results showed that the α-values between 0.4 and 0.6 had the lowest energy consumption. The use of a low number of previous days also achieved greater reductions in heating energy consumption, whereas a larger number of days was applied to cooling energy consumption. This study makes progress in using adaptive setpoint temperatures optimally to reduce the energy consumption in the building sector. • Modification of setpoints in 390 simulations to optimize energy consumption. • The α-values between 0.4 and 0.6 had the lowest energy consumption. • The number of previous days varied to optimize heating and cooling consumption. • A saving between 25.73 and 44.89% of the total energy consumption by using adaptive setpoint temperatures. • Better performance of the α-value from ASHRAE 55–2017 than that from EN 15251:2007. [ABSTRACT FROM AUTHOR]