Search

The paper presents a Computational Fluid Dynamics (CFD) model of the cold alpha-type Stirling engine. The developed mathematical model comprises of Unsteady Reynolds Averaged Navier-Stokes (URANS) set of equations, i.e. continuity, momentum and energy equations. Moreover, the developed mathematical model comprises a non-equilibrium description of the regenerator, by the introduction of the energy conservation equation for the regenerator matrix. It was implemented in the framework of commercial CFD software ANSYS Fluent. The work presents an in-depth analysis of the influence of the numerical mesh and applied turbulence model on the obtained results. The model was used to analyse the influence of the regenerator on the performance of the cold Stirling engine at different operating conditions. It appeared that on an average application of the regenerator increased the engine specific work by 10 J/kg and this increase is significantly higher at a high rotational speed of the engine. At the same time, the engine efficiency averagely was increased by 10 percent points and again this increase was significantly higher at higher rotational speeds of the engine. Especially, the influence of the heat source and sink temperatures on the engine operation were analysed. It appears that the lower are temperatures of a heat source and sink the more pronounced is the presence of the regenerator in the engine. Finally, the influence of the elementary parameters: particle diameter and porosity of the solid matrix which constitute the regenerator filling was investigated. It was shown that for the analysed engine the optimal value of the regenerator packing porosity equals about 0.72 it results in the specific area of the regenerator equal around 1675 m2/m3. Obtained results can be used to analyse the possibility of application of Stirling engines to recover low-temperature exergy of regasified Liquified Natural Gas (LNG), which for small regasification units can be alternative for commonly utilised Ambient Air Vaporizers (AAV) and it aside for regasification of LNG it could produce electric energy. [ABSTRACT FROM AUTHOR]

In the paper, a second order thermodynamic analysis of a small scale alpha-type Stirling engine is presented. The developed mathematical model is based on the Finite Time Thermodynamics (FFT) approach and it is derived from the differential time dependent equations of energy and mass conservation. The engine model consists of three spaces: compression, expansion and regenerator. In contrast to available models, the model presented in this paper assumes polytropic processes in the compression and expansion spaces, which corresponds to the non-ideal heat transfer in these spaces. The results, obtained using the developed second order model, were compared with the results obtained using the Computational Fluid Dynamics (CFD) analysis of the same engine. A very good agreement between the second order model and the CFD model was achieved. Finally, the developed model was applied to analyse potential to recover cryogenic exergy of the Liquefied Natural Gas (LNG). The paper presents the results of the dimensional upscaling of the engine and the influence of the average working pressure. It was revealed that increasing the size of the engine or the average working pressure moves the engine to practically unachievable working conditions. [ABSTRACT FROM AUTHOR]

The paper presents a thermo-ecological analysis of a liquefied natural gas regasification system equipped with a Stirling engine. The proposed system includes an alpha configuration machine, working as a cold engine with the heat sink acting as the evaporator for the LNG and the upper heat source being at ambient temperature (sea water) or moderately higher. The engines are modelled using two approaches developed by the authors, that is a CFD model and a second-order one-dimensional model. First a small engine is modelled by both CFD and the second order approach to compare results and after confirming their similarity, due to a lower computational cost a larger machine is modelled with the second order model. Due to the heat transfer conditions being crucial for a Stirling cycle machine's performance, those are investigated. It is shown that the internal, convective heat transfer coefficients are much higher in cryogenic conditions than in typical ones. The results of engine assessment are used for the Thermo-ecological cost (TEC) analysis. Within the thermo-ecological analysis, the influence of selected parameters is demonstrated. Additionally the TEC of electricity generated in cold power plant is presented for different configurations. In the case of analysed Stirling systems savings of natural gas reach the level of only 0.5%. However, when TEC of electricity is calculated, the savings are at the level of 72%. The proposed theoretical investigations are the base for the acquisition of new knowledge in the field of possible ways of converting cryogenic exergy of LNG into electricity and optimization of this cycle with strong focus on ecological effects, including the TEC. [ABSTRACT FROM AUTHOR]