Search

This paper describes the performance of the Regional Atmospheric Modeling System (RAMS) in simulating a winter drought event, based on two different forcing datasets. We ran EC (ERA-Interim reanalysis data as initial and lateral boundary forcing conditions) and FNL (NCEP-FNL reanalysis data) simulations for the 2008/2009 winter drought event to quantify the impact of any uncertainty in the different initial and lateral boundary forcing data on regional model outputs. The response of the winter mean atmospheric states to the variations in the initial and lateral boundary conditions was investigated on the basis of these simulation results. The spatio-temporal features of precipitation from the EC and FNL runs closely resembled those measured from the Global Summary Of the Day (GSOD) observations, although the EC run data outperformed the FNL run data in both their spatial distribution patterns and precipitation values. The water vapor flux values explain how the differences in the precipitation values between the EC and the FNL runs were generated, whereas temperature values were not sensitive to any changes in forcing data. The model results from these runs also slightly overestimated temperature on both spatial and temporal scales. For the tropospheric atmospheric data recorded at the Fuyang Meteorological Station in Anhui Province, neither the time series nor the statistical analyses showed any evidence of superiority between the two different driver datasets compared with radiosonde data. However, on closer inspection, the influence of different initial and lateral boundary conditions on modeling the tropospheric atmospheric data appeared to be evident. [ABSTRACT FROM AUTHOR]

Based on a public building in China, this paper built a benchmark model and analyzed the influence of main thermal performance of building envelopes on energy consumption in different climatic regions by EnergyPlus. The results showed that in the order of hot summer and warm winter region, hot summer and cold winter region, cold region, severe cold region, the energy-saving effect was getting better and better with the increase of roof insulation, exterior wall insulation and exterior window insulation. If SHGC of exterior window was reduced, building energy consumption decreased in hot summer and warm winter region, hot summer and cold winter region, but it increased in cold region and severe cold region. For hot summer and warm winter region, hot summer and cold winter region, the factors that affected energy consumption was as follows: SHGC > K win > K wal > K ro, for cold region and severe cold region, it was as follows: K win > K wal > SHGC > K ro . [ABSTRACT FROM AUTHOR]

In recent years, Beijing rural “coal to electricity” is more and more attention. Among them, the air source heat pump as a clean energy is vigorously promoted, but due to of its low water supply temperature. So, for what kind of terminal equipment need to be researched. In this paper, the two terminal equipment of PE-X pipe are adopted as the low-temperature floor radiant heating and four-post 760 cast iron radiator in the bedroom of a Beijing farmhouse are simulated. The performance of two kinds of terminal equipment is analyzed from four aspects: indoor temperature field distribution, indoor air cleanliness, indoor air velocity distribution and energy consumption. The commercial CFD software was used to simulate the characteristics of two heating terminal equipment. The simulation results show that PE-X pipes as the low-temperature floor radiant heating is better than that the four-post 760 cast iron radiator heating, it has good heating effect. [ABSTRACT FROM AUTHOR]

Planetary rovers may traverse terrains with complex geometries and variable physical properties, but their mobility behaviors are complicated and difficult to simulate precisely. This article focuses on high-fidelity dynamic modeling and simulation for a type of rovers that incorporate single-input-multi-output joints to enhance terrain adaptability, which has been used on China's Tianwen-1 Mars rover. A novel multibody dynamic model and its solutions are derived first with consideration of single-input-multi-output joints. Then, a unified terramechanics model is proposed, considering variable terrain surfaces and covering rover's motion states of skidding, slipping, and steering, solved the problem of simulation instability caused by model switching between soft and hard terrains. As the contact areas of wheels with various terrains and resultant sinkage are dominant factors to ensure fidelity but difficult to determine, a new terrain modeling method for calculating contact area and wheel sinkage is developed using digital elevation map with physical properties. A simulation system is developed, integrating all the above models, and verified with physical experiments and commercial software. The relative simulation errors that have been achieved are less than 5.9% for bogie angles, 6.1% for drawbar pull, and 3.4% for slip ratios, demonstrating high fidelity simulation results. [ABSTRACT FROM AUTHOR]

To simulate and analyze a large aircraft with severe wind shear, nonlinear equations for a rigid aircraft under various wind conditions were designed. In this paper, a double-vortex-ring method is adopted to generate a three-dimensional microburst wind field. This model incorporates a flight dynamics module and three flight simulations based on various forms of nonlinear equations. In addition, four primary wind gradients are considered to compute the aerodynamic coefficients. In simulation experiments with a China C series large aircraft, equations using air-relative velocities and inertial velocities are compared and analyzed. Although the nonlinear equations derived using the air-relative velocities should be identical to those using the inertial velocities, the results show that the latter are more accurate in practice because the former bring error into the simulation when estimating the acceleration induced by the wind field. [ABSTRACT FROM AUTHOR]

In this research, an integrated simulation-optimization modeling approach (ISOMA) was developed for supporting agricultural N2O emission mitigation at the watershed scale. This approach can successfully combine soil N2O emission simulation and the consequential mitigation management within a general modeling framework. Also, uncertainties associated with the key soil parameter can be effectively reflected and addressed through adoption of Monte Carlo analysis for the simulation results. The Monte Carlo simulated results were then used to generate fuzzy membership functions that can be consequentially used for emission mitigation management, reflecting the combined uncertainties for N2O emission simulation and mitigation management. The developed ISOMA was then applied to a reservoir watershed in Miyun county of Beijing municipality. In the studying watershed, the simulation model was calibrated and verified. Then, N2O emission from multiple agricultural land-use patterns were predicted. The amounts of N2O emission of four land use patterns (i.e., cash tree, orchard, cropland, and natural forest) were (536.9, 590.8, 653.1), (237.7, 254.4, 275.9), (79.5, 100.7, 105.1), (33.0, 47.3, 61.1) kg CO2 eq ha−1 year−1, respectively. Two scenarios (i.e., G1 and G2) were set up according to development priorities of local economy and society. Meanwhile, multiple credibility levels were considered according to the risk of N2O emission. The land use patterns could be adjusted according to solutions of ISOMA. The developed methods could help regional manager choose various production patterns with cost-effective agriculture N2O emission management schemes in the Miyun reservoir watershed. The manager also can obtain deeply insights into the tradeoffs between agricultural benefits and system reliabilities. [ABSTRACT FROM AUTHOR]