Search

The present study aims to examine the deformation and annealing behaviour of Fe–0.07C–20Mn–2.6Si–1.6Al TWIP steel in the viewpoint of microstructural characterisation, fault analysis, triaxial residual stress measurement and mechanism of twin formation. 50% cold deformation results in improvement of hardness and tensile strength (428 HV and 1419 MPa, respectively), whereas annealing at 900 °C of the same leads to improvement in ductility (61%) with the decrease in strength (873 MPa). The residual stress is maximum and compressive in nature in deformed sample which has been diminishing after annealing. Hot rolled and hot rolled-solution treated samples develop dual phase microstructure along with annealing twins, whereas fine nano twins and high dislocation density with dual phase microstructure are apparent after 50% cold deformation. The presence of Shockley partial dislocation, overlapping of stacking faults, Lomer-Cottrell lock, intrinsic and extrinsic stacking faults affect the mechanical properties as obstacles of dislocation movements or assisting twin formation. Goss and Brass components of texture are dominating after rolling, whereas annealing results in weakening of rolling texture components. The nucleation mechanism of twin has been consistent with the pole mechanism along with the deviation process. Hence the present work amplifies the present understanding of deformation and annealing behaviour on low carbon dual phase TWIP steel from different characterisation perspectives. [ABSTRACT FROM AUTHOR]

The present study deals with the influence of cold rolling on microstructure, texture and mechanical properties of low carbon high Mn TWIP steel. It is noticed that the hardness, yield strength and tensile strength of the specimens increase whereas percentage elongation decreases as the amount of cold rolling reduction increases. The fully austenite phase with the average grain size of about 55 µm along with annealing twins became fragmented and flattened when subjected to 10–50% cold deformation. The cold deformation results in the evolution of sub-structure, comprising dislocations, twins as well as interaction of dislocations and twins. The hot rolled and air cooled sample (0% cold deformation) reveals γ-fibre (〈111〉//ND) texture, whereas cold rolled samples shows Goss texture ({110}〈001〉) and Brass texture ({110}〈112〉) components, which are expected after cold deformation of austenitic steels having lower stacking fault energy in the range of 15–40 mJ/m 2 . X-ray line profile analysis through extended convolution multiple whole profile fitting method is utilised to quantify the dislocation density and planar fault (twin) probability for the cold rolled samples with different degree of reduction. Fractography shows that with the increase in cold deformation, fractures become more and more brittle in nature. [ABSTRACT FROM AUTHOR]

The present study aims to investigate the evolution of microstructure of 304 austenitic stainless steel (SS) due to reversion annealing of cold deformed samples under different schedules. Evolution of phases in selected samples was identified and quantified by X-ray diffraction analysis along with corresponding microstructural characterisation through optical, scanning and transmission electron microscopy. Mechanical properties of the samples were determined by carrying out tensile test. Electron microscopy of selected samples has revealed that, while strain induced martensite, deformation twins, ε-martensite and high dislocated structures are the dominant microstructural features of the cold deformed samples, reversion annealing of the same results into ultrafine-grained reverted austenite, cell type dislocation sub-structures with some amount of untransformed martensite. The maximum tensile strength of 1589 MPa with an elongation of 9% has been obtained after 20% deformation at −196 °C (20LND), whereas 40% deformation at 0 °C (40ZCD) results into a tensile strength of 1225 MPa with 13% elongation. Annealing of 40ZCD and 20LND specimens at 300 °C results in significant improvement in tensile strength, while annealing at 725 °C increases the elongation with a decrease in tensile strength. During reversion annealing, strain induced martensite transforms to austenite through shear and diffusional processes. However, the reversion is essentially diffusional in nature at a higher temperature. [ABSTRACT FROM AUTHOR]

304 austenitic stainless steel plates have been deformed (10 to 40%) by multi-pass cold rolling incorporating soaking at 0 °C and − 196 °C after each pass with an aim to correlate the microstructure and mechanical properties under cold/cryogenically deformed conditions. Characterisation of phase constituents, microstructure and mechanical properties of such steel specimens has been conducted after processing under different schedules. Rolling of the investigated steel at near cryogenic temperature results into the formation of extended stacking faults, ε-martensite and α′-martensite in contrast to the formation of homogeneous dislocation structure along with α′-martensite in the samples rolled at 0 °C, which can be correlated with temperature dependent stacking fault energy. EBSD phase analysis reveals 46.3% and 69.2% α′-martensite in the austenitic matrix for 10% and 20% deformation at − 196 °C, respectively. Deformation twins are evident in all the samples rolled at 0 °C as well as − 196 °C. 40% cold deformation at 0 °C leads to high strength (1225 MPa) and 13% total elongation, whereas comparatively lower 10–20% deformation at − 196 °C leads to higher level of strength (1306–1589 MPa) with 15–9% elongation due to the formation of the higher volume fraction of strain induced martensite (ε/α′). [ABSTRACT FROM AUTHOR]

Ultrahigh strength steel is designed for light-weight cost-effective parts with improved safety by dint of high strength coupled with better fuel efficiency for automotive and aerospace applications. The current steel with medium carbon (0.28 wt%) and alloying elements (∼8%) such as Mn, Ni, Mo along with micro-alloying of Ti and Nb has been processed by thermo-mechanical controlled processing with different finish rolling temperature (FRT) followed by air cooling and water quenching. Microstructure of air cooled specimen consists of lower bainite with a few amount of lath martensite, whereas a mixture of lath martensite and lower bainite in prior pan-caked austenite grains has also been obtained on water quenching. It is observed that microstructure becomes gradually finer with reduction of FRT for both cooling conditions and fine-scale carbide/carbonitride precipitates, enriched with Ti/Nb along with dislocation sub-structures within bainite and martensite laths have performed as strengtheners. Ultrahigh strength (1991–2032 MPa) with lower elongation (5–7%) is obtained in water quenched samples, whereas air cooled samples show comparatively lower strength (1841–1928 MPa) with marginally higher elongation (8–9%). Different strengthening mechanisms have been quantified which cumulatively contribute to the yield strength of the current steels. [ABSTRACT FROM AUTHOR]

A low-carbon microalloyed steel containing high Ni and Cu content has been developed and subjected to thermo-mechanical processing by varying the finish rolling temperature (FRT∼850–750 °C) and cooling rates (air cooling and water quenching). Microstructures of air cooled samples consist of granular bainite and lath or plate-like bainite, whereas, water quenched samples exhibit a mixture of lower bainite and lath martensite. A refinement in microstructure has been noticed with the decrease in FRT and increase in cooling rate. Transmission electron microscopy demonstrates the presence of coarse (Ti, Nb)C precipitates (~90–160 nm) and fine Cu precipitates (<20 nm). Macro-texture and micro-texture results reveal the dominance of Goss and rotated Goss texture components, which strengthened with the decrease in FRT and increase in cooling rate. The proposed steel composition and TMCP schedule have offered YS ∼ 1000 MPa, UTS ∼ 1400 MPa, total elongation greater than 10% maintaining a low YS: UTS ratio (0.68–0.80). Such a satisfactory combination of tensile properties achieved in as-cooled or as-quenched conditions (without the need of any tempering treatment) makes the steel suitable for automotive application. [ABSTRACT FROM AUTHOR]

In this study, we report synthesis of highly ordered self-organized nanoporous alumina membranes (NAMs) with two distinct pore diameter ranges by two step anodization technique from two different electrolytes containing simple H 2 SO 4 and mixed electrolyte consisting of H 2 SO 4 and ethylene glycol. Three different complimentary techniques field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM) and small X-ray scattering (SAXS) were used to characterize the synthesised membranes. An attempt was made to correlate the pore parameters obtained from low ensemble size two dimensional FESEM and AFM micrographs and from large area three dimensional scattering using SAXS. A special attention was given in estimating the porosity of these ordered membranes and compared the results. It was demonstrated that such controlled synthesis method can result in improved pore regularity in NAMs along with enhanced porosity, greater than 40%. [ABSTRACT FROM AUTHOR]

Two C-Mn-Si steels with and without Nb micro-alloying are selected in the present study. Both these high carbon steels have been thermo-mechanically processed using Gleeble 3800 simulator. Optical microscope (OM), scanning electron microscope (SEM), transmission electron microscope (TEM), atomic force microscope (AFM) were utilised for microstructural characterisation. The austenitising temperature was varied from 1150 °C to 1200 °C followed by hot compression and subjected to free cooling to evaluate the influence of austenite grain size on transformed microstructure and mechanical properties. It is evident that higher austenite grain size is obtained for both types of steels subjected to higher austenitising temperature. The refinement of pearlite interlamellar spacing (<0.20 μm) with degenerated morphology as well as finer prior austenite grain size (<40 μm) is found to be more prominent for Nb micro-alloyed sample. The average hardness values of both the steels are higher for the specimens, treated at a higher austenitising temperature which is attributed to finer interlamellar spacing. Finally, the correlation between the evolving microstructure and resulting mechanical properties (hardness and yield strength) has been made. [ABSTRACT FROM AUTHOR]

The present study describes the fabrication of TiN particulates reinforced SS316 based Metal Matrix Composites (MMCs) in nitrogen and argon atmosphere. The influence of sintering process parameters on microstructure, density, porosity, wear rate and microhardness of the fabricated samples has been analyzed. The input variable process parameters, such as, laser power density (range: 4.13–5.57 W/cm 2 (× 10 4 )), scanning speed (range: 3500–4500 mm/min) and the constant parameters, such as, laser beam diameter (0.4 mm), hatching distance (0.2 mm) and layer thickness (0.4 mm) have been considered in the process. It has been observed from Field Emission Scanning Electron Microscopy (FESEM) analysis that TiN and SS316 powder mixture can be sintered in which chromium acts as a binder. Fine gaps are not found at the interface between TiN and SS316 when the mixture is sintered in nitrogen atmosphere. With an increase in the percentage of TiN, the density and wear rate decreases. However, when the reinforcement is taken beyond 18% by weight, the wear rate starts increasing. The microhardness also increases with an increase in the percentage of TiN. The microstructure, elemental compositions and phase characterization of the developed sintered MMCs have been examined by FESEM, EDX (Energy-dispersive X-ray spectroscopy) and XRD (X-ray diffractometer) analysis, respectively. The results have demonstrated the suitability of the TiN reinforced SS316 MMCs for industrial applications. [ABSTRACT FROM AUTHOR]