Search

Nonisolated dc–dc converters are fundamental building blocks in the power supply for a wide range of applications. To cater to this heterogeneity in applications, development of dc–dc converters with suitable voltage conversion ratio (G) is imperative. Given a converter topology, G can be found out uniquely by using the principle of inductor volt-second balance, and the process of obtaining the voltage conversion ratio from the topology is simple. In contrast, the inverse problem, i.e., the process of obtaining the converter topology for a given voltage conversion ratio (G) is a challenging task, and the obtained topology is also not unique. This article presents a simple method to obtain a family of converter topologies from a required voltage conversion ratio. This method utilizes the principle of inductor flux balance as a synthesis tool. The step-by-step procedure to synthesize the converter topologies is outlined. To illustrate the efficacy of the proposed method, it is applied to synthesize various quadratic buck–boost topologies, and a family of converters is identified. Operation and feasibility of two novel topologies, identified by the proposed theory, are verified experimentally. [ABSTRACT FROM AUTHOR]

This paper describes a theory to synthesize nonisolated dc–dc converters. It uses the fundamental flux balance equation across the inductors of a converter as a starting point in this synthesis process. The flux balance equations are the linear equations of the input voltage, capacitor voltages, and duty cycle (D). The coefficients of these linear equations can be selected from a finite set of choices. These choices define the converter topologies that are subsequently used to synthesize a converter. The synthesis procedure applies to a converter of multiple order. All the possible converters are identified for a first-order topology. In the case of second-order converters, all the choices of the flux balance equation are defined. Based on these choices, three new quadratic topologies are derived and verified to demonstrate the effectiveness of the theory. The procedure to synthesize a converter from a given voltage conversion ratio is also outlined. [ABSTRACT FROM AUTHOR]

Due to the pulsating power at the inverter output terminals, the passive storage elements of the boost stage of the current-fed switched inverter (CFSI) contain a power frequency harmonic component (100 Hz), apart from dc and switching frequency components. In prior designs, the second harmonic component is suppressed by increasing the size of the input filter inductor and capacitor or by using additional circuits. This paper presents a complete characterization of a control-based approach to suppress the power frequency harmonic component in the input inductor current of a CFSI. It also presents a comprehensive characterization of the harmonic power redistribution. Using the proposed approach, it is demonstrated that the inductor value of a CFSI is reduced by 61% for the same peak-to-peak ripple. This leads to an improvement in the conversion ratio, efficiency, and power density of the overall converter. A SiC MOSFET-based CFSI with 75-kHz switching frequency is used to verify the proposed design philosophy. [ABSTRACT FROM AUTHOR]

Impedance source inverters (ISIs) are gaining attention due to features such as single-stage conversion, buck-boost capability, and inherent shoot-through protection. To maintain the required ac output voltage, typically ISIs are operated at a higher dc-link voltage due to constrained modulation index. This also increases voltage stress across capacitors and switches of the converter. This voltage stress is approximately double compared to that of voltage source inverter with preboost stage (Boost-VSI). To mitigate this problem, a new pulsewidth modulation (PWM) scheme for the active-front-end based ISIs (AFE-ISIs) is proposed. The proposed scheme enables the ISIs to produce high ac gain with lower voltage stress across the capacitor and switches. In other words, the proposed scheme blends the advantages of Boost-VSI into ISIs. With the new PWM scheme, there are also reductions in output voltage total harmonic distortion, switching frequency ripple in the inductor current, and power loss in the converter. A prototype of the current-fed switched inverter, an AFE-ISI, is designed, and the proposed PWM scheme is implemented. Experimental results obtained are in accordance with the proposed theory and show that the voltage stress has reduced from 325 V to 203 V for an ac output of 110 V. [ABSTRACT FROM AUTHOR]

Power-hardware-in-the-loop (PHIL) simulations are used to test power hardware with the help of computer-based real-time simulations. Generally, buck-based power amplifiers that have good dynamic performance are used to construct a PHIL simulator because of their linear large signal control-to-output characteristics. However, their output voltage peak is limited to the applied dc input in the linear region of modulation. In this paper, a differential boost converter (DBC)-based power amplifier is proposed for PHIL simulations, which does not suffer from the aforementioned limitations of a buck-based amplifier. A conventional DBC exhibits highly nonlinear control-to-output behavior. A feedback linearization technique is used to linearize the DBC in a large signal and dynamic sense, which makes it suitable for PHIL applications. Using this power amplifier and a MATLAB/Simulink toolbox for real-time simulations, the PHIL simulator is constructed. Experimental results under various operating conditions of source voltages, such as unipolar, bipolar, transients in frequency, and the dc step, and various load conditions, such as reactive, nonlinear, and transient faults, are provided to confirm the efficacy of the proposed PHIL simulator. [ABSTRACT FROM PUBLISHER]