Search

Introduction. The Shchuchiy Bay is located in the western part of the skerry area of Lake Ladoga near the town of Priozersk. For almost 20 years, the bay has experienced an anthropogenic impact from the ingress of untreated wastewater from the Priozersk Pulp and Paper Mill (PPM). Systematic microbiological studies of the Shchuchiy Bay ecosystem were started in the middle of the 1970s by the Institute of Limnology of the Russian Academy of Sciences and continued after the PPM closure in 1986. Materials and methods. The ecosystem of the bay was studied in detail during the growing season of 2013–2014; periodic studies were carried out in 2015–2018. Retrospective data were also used for the analysis. Water samples were taken at four stations from the surface horizon. The following microbiological indicators were determined: the abundance of bacterioplankton and the percentages of various morphological types of bacterial cells. Results and discussion. A comparison of the quantitative level of development of the bacterial community in the bay in different periods showed a gradual decrease in the abundance of bacterioplankton as the anthropogenic impact weakened after the closure of the Priozersky PPM from 12.40 million cells ml–1 in 1987 to an average value of 2.62±1.03 million cells ml–1 in 2013–2018. A positive correlation was found between the concentration of bacteria and water temperature. The percentage of rod-shaped microorganisms in the water of the bay also decreased as the anthropogenic impact weakened from 73.4 % in 1987 to 53.1±7.6 % in 2013–2018, which indicated an improvement in water quality. Conclusion. A stable decrease in the abundance of bacteria from the level characteristic of highly polluted and eutrophic water bodies to the level characteristic of mesotrophic and mesotrophic-eutrophic water bodies is a reliable criterion for the restoration of the ecosystem of the Shchuchiy Bay to the state characteristic of similar bays of Lake Ladoga.

Hydrothermal liquefaction derived hydrochar produced from industrial paper sludge was used as an adsorbent to remove phenol derivatives from an industrial wastewater stream. Removal efficiency for phenol was determined using synthetic solutions (10–150 ppm) using batch adsorption experiments at a constant solution pH (8), temperature (25 ± 2 °C) and rotary speed (150 rpm). The adsorption of phenol onto hydrochar followed a Freundlich isotherm and could be described with pseudo-second-order kinetic models. Analysis of the adsorption mechanisms showed that particle film mass transport was the rate-determining step in the adsorption process. A COD removal efficiency of 31 ± 1% was achieved for the industrial wastewater stream. All phenol components in the wastewater stream could be removed, but not all organic acids and cyclic ketones. The performance of the paper sludge-based hydrochar compared well with that of activated carbon (44% COD removal). The final phenol concentration in the wastewater stream was below the acceptable phenol concentration for industrial effluents (1 mg/L). The results show that paper sludge can be converted to a valuable marketable commodity that could reduce waste management costs for a paper mill, while also reducing the cost of expensive adsorbents. Highlights Industrial paper sludge waste was successfully converted to effective bio-adsorbent.; HTL-based biochar was used as adsorbent without any pretreatment.; 77.83% COD removal from industrial wastewater could be obtained.; Final total phenol concentration was below 1 ppm.; Bulk fluid mass transfer was the rate determining step in the adsorption process.

Nitrogen-fixing bacteria (NFB) can reduce nitrogen at ambient pressure and temperature. In this study, we treated effluent from a paper mill in sequencing batch reactors (SBRs) and monitored the abundance and activity of NFB with a view to producing a sludge that could work as a biofertilizer. Four reactors were inoculated with activated sludge enriched with NFB and fed with a high C/N waste (100:0.5) from a paper mill. Though the reactors were able to reduce the organic load of the wastewater by up to 89%, they did not have any nitrogen-fixing activity and showed a decrease in the putative number of NFB (quantified with qPCR). The most abundant species in the reactors treating high C/N paper mill wastewater was identified by Illumina MiSeq 16S rRNA gene amplicon sequencing as Methyloversatilis sp. (relative abundance of 4.4%). Nitrogen fixation was observed when the C/N ratio was increased by adding sucrose. We suspect that real-world biological nitrogen fixation (BNF) will only occur where there is a C/N ratio ≤100:0.07. Consequently, operators should actively avoid adding or allowing nitrogen in the waste streams if they wish to valorize their sludge and reduce running costs. PRACTITIONER POINTS: Efficient biological wastewater treatment of low nitrogen paper mill effluent was achieved without nutrient supplementation. The sludge was still capable of fixing nitrogen although this process was not observed in the wastewater treatment system. This high C/N wastewater treatment technology could be used with effluents from cassava flour, olive oil, wine and dairy industries.

Lecturers are required to produce scientific papers for improving their careers. However, there are many lecturers who do not understand how to write scientific papers and to publish it. This community service aims to improve the competence of lecturers in writing scientific papers so that they can make good scientific papers and can publish it. The program is carried out in two stages: 1) preparation stage, and 2) implementation through training on writing scientific paper. The results showed that the participants were able to understand 1) the basics of scientific writing, 2) the parts of scientific articles, 3) the scientific publication policies, 4) the criteria and requirements for publishing scientific papers in accredited journals, 5) the paraphrase techniques, 6) the citation using Mendeley, and 7) the technique of compiling according to the standard template of accredited journals.

High-colored wastewater generated during the cellulose bleaching process causes the inhibition of biological activity when released into the environment. This study aimed to evaluate the bacterium’s capacity, identified as RGM2262, to degrade a complex phenolic structure such as lignin, which is found in high concentrations in the effluents generated during the production of cellulose, raw material for the manufacture of paper. To determine the values of the experimental variables that allow for a greater degradation of organic matter, an experimental model was carried out through experimental design. Thus, the experimental matrix was obtained with the variables pH 7 (−1) to 9 (+1) and a treatment time of 1 day (−1) to 5 days (+1). The results show that, at pH 8 and pH 9, both treatments—with bacteria in bio-films and without bio-films—were efficient. On the second day of treatment, 100% of the color and the phenolic structure were removed, with a similar rate constant, and at the same time, 80% COD and 70% of TOC, respectively.

In the present study, adsorption of colour and other pollutants from agro-based paper mill effluent onto fabricated coal fly ash nanoparticles (CFA-N) have been investigated. Response surface methodology was applied to evaluate the operational conditions for maximum ouster of colour from effluent by nano structured CFA-N. Maximum reduction in colour (92.45%) and other pollutants were obtained at optimum conditions: 60 min interaction time, 60 g/L adsorbent dosage and 80 rpm agitation rate. The regression coefficient values (adjusted R2 = 0.7169; predicted R2 = 0.7539) established harmony between predicted and the experimental data. The adsorption equilibrium results matched perfectly with both Langmuir and Freundlich isotherms with maximum adsorption capacity of 250 platinum–cobalt/g. Additionally, the efficacy of CFA-N was also assessed in a continuous column mode. Furthermore, the feasibility of treated effluent for irrigation purpose was checked by growing the plant Solanum lycopersicum. Overall, the findings demonstrated the outstanding role of inexpensive and abundantly available CFA-N in treatment of paper mill effluent to the required compliance levels. HIGHLIGHTS Nano fly ash was successfully utilized for removal of colour and other pollutants from agro-based paper mill effluent.; RSM using BBD was used to optimize the operational conditions.; Quadratic models have been established for the response variables.; Fixed-bed column adsorption studies illustrated the feasibility of nano fly ash for pilot-scale applications.; The reusability of treated effluent for irrigation was examined.

In this study, Taguchi experimental design was used to the optimize operating parameters for the degradation of paper mill effluent using electrochemical (EC) process with two-dimensional concentric aluminum tube electrodes (CATE). For this purpose, four significant experimental factors were used in four levels pH (6–9), electrolysis time (10–40 min), voltage (6–12 V) and surface area (357–624 cm(2)). The process parameters were optimized, through performing L16 orthogonal array of Taguchi technique, for the removal of chemical oxygen demand (COD) and turbidity. The percent COD and turbidity reductions were transferred into an accurate S/N ratio for a larger value is the better (LBT) response. The study presents a unique method of finding optimum combination of process parameters to illustrate their effect on the turbidity and COD reduction. The treatment conditions for the maximum elimination of the pollutants were second level of pH (7), third level of ET (30 min), fourth level of voltage (12 V) and second level of surface area (446 cm(2)). The confirmation experiment results were within the confidence intervals (CI) indicating an acceptable agreement between predicted and observed values. Based on the p-values, the electrolysis time and voltages were found to be the most significant factors for both COD and turbidity reduction. The findings of research indicated, that the Taguchi method can be used successfully for the treatment of paper industry effluent by electrochemical technique.

Anaerobic digestion (AD) is an essential technology for wastewater management, resource recovery and biogas production, and it is considered as an efficient and reliable treatment method for many wastewaters. Operating parameters have been shown to directly affect the stability and treatment performance of AD, especially temperature. For 180 days, the AD of recycled paper mill wastewater (RPMW) was carried out in a modified anaerobic inclining-baffled (MAIB) reactor under various temperature conditions, i.e. 29 °C (low mesophilic), 37 °C (mesophilic) and 55 °C (thermophilic). It was found that total COD removal of 94, 96 and 76%, and methane yields of 0.125, 0.196 and 0.256 L CH4/g CODremoved were attained at temperatures of 29, 37 and 55 °C, respectively. Throughout the three transition periods, the pH level in the MAIB reactor fluctuated slightly within the range of 5.8–6.5 without affecting the system stability. The results concluded that thermophilic condition strongly influenced the MAIB reactor performance, leading to lower COD removal, higher methane yield and gradually recovered pH level. Highlights Novel modified anaerobic inclining-baffled (MAIB) reactor, which combines the development of attached and settled microorganisms, was operated for the treatment of recycled paper mill wastewater (RPMW).; The operational temperature intensive analysis of MAIB was investigated at thermophilic and mesophilic conditions.; The system compartmental characteristics were also analyzed and discussed.

In order to obtain a lignin-based adsorbent with low cost, simple operation and no further modification, a calcium lignin adsorbent was prepared from chemical mechanical pulping (CMP) waste liquor by directly calcification from lime. The calcium lignin was characterized by BET, SEM, TEM, FT-IR and solid-state NMR analyses. The results showed that the molecular structure of the calcium lignin particles did not change when compared to sodium lignin, the formation mechanism of calcium lignin was revealed. The initial COD and lignin contents of CMP waste liquid were 54858 mg/L and 24.39 g/L, the conversion rate of lignin can reach 71.36% when was deal with lime. Thus, most of the lignin resources in the waste liquid were recovered. The middle-stage wastewater (MSWW) of pulping and papermaking was dealt with calcium lignin, the COD removal rate was up to 85.83%. The adsorption isotherms and kinetics were well fitted by the Langmuir model and pseudo-second-order kinetic model, respectively. Lime was regenerated from the used calcium lignin with high-temperature calcination, the conversion rate of calcium ions can reach 83.56%. Overall, the calcium lignin prepared by the one-step method exhibited great potential for effectively removing COD from middle-stage wastewater.

The technique of using biochar-based catalysts in persulfate activation is a promising alternative to remov emerging and refractory pollutants (e.g., tetracycline-) in wastewater. However, the situation of biochars derived from waste pulp/paper mill sludge is still unclear. The pulp/paper mill sludge biochars (SBC300, SBC500, and SBC700) were obtained and characterized at pyrolysis temperatures of 300, 500, and 700 °C. Tetracycline degradation using peroxydisulfate activated by SBCs was investigated. The results demonstrated the removal efficiencies of tetracycline in SBC300-, SBC500- and SBC700-peroxydisulfate systems, which increased with the pyrolysis temperatures and were 4.3, 4.8, and 5.0 times that of a system with peroxydisulfate alone. The experiments of free radical quenching, singlet oxygen quenching, and electrochemistry indicated that the degradation of tetracycline in SBC-peroxydisulfate systems was mainly not a free radical pathway, but a non-radical pathway. Singlet oxygen (1O2) and electron transfer could play main roles in the degradation removal of tetracycline. The removal efficiencies of tetracycline in the SBC-peroxydisulfate systems could be up to 96.0% (SBC700-peroxydisulfate) under the optimum dosage of SBC, the molar ratio of peroxydisulfate to tetracycline and the solution pH value. The results indicate that a SBC700-peroxydisulfate system could be an effective “trash-to-treasure” treatment technique for wastewater containing antibiotics.

Microfluidic paper-based analytical devices are emerging as promising options for on-the-spot detection of chemical contaminants in water. The coupling of these devices with digital imaging technol...

Declining carbon (C) content in agricultural soils threatens soil fertility and makes soil prone to erosion, which could be rectified with organic soil amendments. In a 4‐yr field trial, we made a single application of three different organic sludges from the pulp and paper industry and studied their effects on cereal yield, soil C content, and fungal and bacterial composition. In laboratory rainfall simulations, we also studied the effects of the soil amendments on susceptibility to erosion and nutrient mobilization of a clay‐textured soil by measuring the quality of percolation water passing through 40‐cm intact soil monoliths during 2‐d rainfall simulations over four consecutive years after application. A nutrient‐poor fiber sludge reduced wheat yield in the first growing season, but there were no other significant effects on cereal yield or grain quality. An input of ∼8 Mg ha−1 C with the soil amendments had only minor effects on soil C content after 4 yr, likely because of fast microbe‐mediated turnover. The amendments clearly changed the fungal and bacterial community composition. All amendments significantly reduced suspended solids (SS) and total phosphorus (TP) concentrations in percolation water. The effect declined with time, but the reduction in SS and TP was still >25% 4 yr after application. We attributed the lower tendency for particle detachment in rain simulations to direct interactions of soil minerals with the added particulate organic matter and microbe‐derived compounds that stabilize soil aggregates. In soils with low organic matter content, pulp and paper industry by‐products can be a viable measure for erosion mitigation.

The paper industry wastewater even after bio-treatment at industrial scale is a major source of aquatic and soil pollution due to various unknown compounds. Hence, the study has focused on the detection of residual organic pollutants from the bleached and unbleached paper mill wastewater and both sources showed endocrine-disrupting compounds. The toxicity test with Phaseolus aureus seed germination showed inhibition of seed germination and alpha-amylase activity >25% in bleached and unbleached paper mill wastewater. The LC50 of Tubifex tubifex was noted of >50% after 48 hours incubation test. This revealed that the wastewater discharged from bleached paper mill is more toxic than unbleached paper mill waste this might be due to the use of more chemicals during bleaching and pulping process. This study has revealed that there is need to treat both paper mill wastewaters adequately prior to discharge.

Introduction. Pulp and paper enterprises accumulate large volumes of industrial waste buried in special accumulation cells. In order to choose a technology for treating above-sludge waters, we need to monitor their composition, which depends on the history of cells’ filling and their subsequent use. Methods. In the course of the study, we applied inductively coupled plasma mass spectrometry (ICP-MS). Results. We determined the content of 72 chemical elements in above-sludge water of 11 cells at Baykalsk Pulp and Paper Mill and 4 open water flows near industrial waste landfills, and performed a cluster analysis of the sample composition. As a result, we revealed the peculiarities of water composition, related to the history of cell filling and subsequent pilot experiments. It has been found that the cells with non-disturbed sediments have cleaner water. Out of 16 chemical elements subject to limitation (Na, Al, P, S, Cl, K, Cr, Mn, Fe, Ni, Cu, Zn, Sr, Mo, Cd, Pb), 11 elements exceed the limits established for wastewater discharged into water bodies within the ecological zones of the Baikal Natural Territory. Each cell is characterized by its own set of elements exceeding maximum allowable concentrations (MAC) and by the extent of such excess. Conclusion. Pilot experiments with cell sediments (joint grouting, drying, dewatering in press-filters) result in the disturbance of the “water/sediment” balance and increase the concentrations of most elements in above-sludge waters. The maximum amounts of elements (6–7) exceeding the MAC values are observed in water in the cells with disturbed sediments, water in the zone of ash slurry discharge, ash and sludge-lignin cells with industrial and household waste. When choosing a technology and procedures for treating above-sludge waters, it is necessary to take into account the specifics of their composition. Using the polluted water flow running into Lake Baikal during catastrophic floods in the summer of 2019 as an example, we show that it is possible to use multi-element ICP-MS analysis to search for sources of pollution from industrial facilities.

The potential application of graphene as a filter paper for selectively removing cationic and anionic dyes from aqueous solutions is demonstrated herein. A surface-tailored graphene paper was fabricated by the vacuum filtration technique on a microporous substrate to remove two different classes of dyes. A negatively charged graphene paper was fabricated from graphene oxide (GO) solution, and a positively charged graphene paper was fabricated from polyallylamine-functionalized GO solution. The solutions of methylene blue (MB) and methyl orange (MO) were filtered through the negatively charged graphene paper (GO−) and positively charged graphene paper (GO+). The stacking structure of the GO− and GO+ paper successfully removed the MB and MO mixtures from the solution. The GO− and GO+ paper demonstrated a high retention rate of 99.8% for MB dye and 99.5% for MO dye. The pore size of the paper was found to be less than 7 nm, providing more insights into the rejection mechanism. The rejection mechanism involves the adsorption and electrostatic interaction (i.e., cationic–anionic interaction) between the dye and graphene sheets, which result in the fast and efficient removal of the dye. The GO paper displayed adsorption capacities as high as 311 and 340 mg g−1 for MB and MO dyes, respectively. The results indicate that the surface-tailored graphene paper is a great alternative for the next generation cost-effective filters in practical water purification applications.

Introduction. Among characteristic features of waste paper recycling plant wastewater, the following can be distinguished: significant fluctuations in consumption and composition, high content of undissolved and dissolved substances (in particular, starch, fiber, dispersed thermoplastic and other substances). Local wastewater treatment can reduce the concentration of undissolved and — partially — dissolved contaminants. Besides, it makes it possible to reuse valuable substances and treated water in production. However, a significant amount of dissolved contaminants is dumped by factories at off-site biological treatment plants. In this case, bioreactors with suspended activated sludge (aeration tanks) as well as bioreactors with attached biomass are used for wastewater treatment. Methods. The purpose of the study was to determine the consumption and composition of wastewater discharged by waste paper recycling plants, as well as the technological parameters and performance of biological treatment facilities, including a moving bed biofilm reactor and aeration tanks. In-process control over the operation of treatment plants was carried out by means of instrumental measurements and laboratory analyses conducted according to standard methods. Results. The article examines the results of the operation of biological wastewater treatment facilities used to treat wastewater from a paper mill, where different grades of waste paper are used as raw materials. The main characteristics of biological wastewater treatment facilities’ operation have been identified. Relationships between the oxidation capacity and the load in terms of organic pollution have been obtained for a bioreactor with a moving bed (1st stage) and aeration tanks (2nd stage of biological wastewater treatment). Measures have been proposed to improve the performance of existing treatment plants.

Lignin is a major by-product of pulp and paper industries, and is resistant to depolymerization due to its heterogeneous structure. Degradation of lignin can be achieved by the use of potential lignin-degrading bacteria. The current study was designed to evaluate the degradation efficiency of newly isolated Bacillus altitudinis SL7 from pulp and paper mill effluent. The degradation efficiency of B. altitudinis SL7 was determined by color reduction, lignin content, and ligninolytic activity from degradation medium supplemented with alkali lignin (3 g/L). B. altitudinis SL7 reduced color and lignin content by 26 and 44%, respectively, on the 5th day of incubation, as evident from the maximum laccase activity. Optimum degradation was observed at 40 °C and pH 8.0. FT-IR spectroscopy and GC-MS analysis confirmed lignin degradation by emergence of the new peaks and identification of low-molecular-weight compounds in treated samples. The identified compounds such as vanillin, 2-methyoxyhenol, 3-methyl phenol, oxalic acid and ferulic acid suggested the degradation of coniferyl and sinapyl groups of lignin. Degradation efficiency of B. altitudinis SL7 towards high lignin concentration under alkaline pH indicated the potential application of this isolate in biological treatment of the lignin-containing effluents. HIGHLIGHTS Bacillus altitudinis SL7 isolated from effluent could efficiently degrade lignin under alkaline conditions.; Degradation efficiency was determined by analyzing lignin content, color reduction, and ligninolytic enzyme activity.; Extracellular laccase from B. altitudinis SL7 can play a significant role in the depolymerization of lignin.; Various low-molecular-weight lignin degradation products were determined through GC-MS.

Pulp and paper wastewater (PPWW) contains numerous refractory and harmful contaminants that require advanced treatment to meet the discharge criteria. This study compared the efficacy of two PPWW treatments: ultraviolet/peroxymonosulfate (UV/PMS) and ultraviolet/H2O2 (UV/H2O2) working under similar circumstances. The initial pH value, oxidant dosage, UV radiation intensity, and pseudo-first-order constant kobs were systematically studied in both systems. Optimally, the UV/PMS process produced an effluent of higher quality than the UV/H2O2, as measured by the removal efficiencies of chemical oxygen demand (COD) in 60 min, which were 48.2 and 64.3% for the respective UV/H2O2 and UV/PMS processes and corresponding kobs values of 0.0102 and 0.0159 min−1, respectively. Radical scavenging experiments demonstrated that •OH was the primary reactive oxygen species in UV/H2O2 process, and •OH and SO4−• in the UV/PMS process. Moreover, ultraviolet-visible spectroscopy and gas chromatography coupled mass spectroscopy analyses showed that deep treatment of petroleum hydrocarbons with carbon chain lengths greater than 18 and macromolecular semi-volatile organic compounds in paper wastewater is difficult, whereas the UV/PMS process can significantly improve the removal of amides, esters, phenols, and other aromatic compounds.

Environmentally recalcitrant pollutants (chromium and sulphate) from mixed effluents of tannery and paper mills were treated simultaneously using highly metal-resistant dissimilatory sulphate-reducing bacteria. The remedial efficiency of the bacteria appeared zero when the bacterial pure culture was employed without the addition of any growth substrate from external source, while the bacterial sulphate reduction and consequent metal removal appeared maximum when sodium lactate was added as growth substrate in another set of experiments. In this set of experiments, almost 100% precipitation of the chromium (700 ppm) occurred in the first 7 days of anaerobic incubation. Sulphate was also removed totally (1225 ppm) in the first 7 days of incubation. pH of the media remained in the neutral to slightly basic range throughout the experimental trial. The achievement of maximum remedial efficiency also depicts the ultimate preference of lactate as carbon source by sulphate-reducing bacteria. The outcomes of the present investigation can be fruitful for designing efficient, environment-friendly and economical bioremedial strategies.

Lithium-ion (Li-ion) batteries have been fabricated in various ways to improve flexibility. Flexibility could be enhanced via active materials, separators, electrodes, and electrolytes, which could then be integrated to form flexible electronic devices with promising electrochemical properties compared to traditional non-flexible Li-ion batteries. Recent progress towards flexible Li- ion batteries fabrication, materials, and their electrochemical properties are investigated in this review. Additionally, recent developments in electronic devices utilizing flexible batteries and their future applications are explored. Portable and wearable electronics, as the primary beneficiaries of the flexible, rechargeable, and high-performance Li-ion batteries, are examined. In the end, various applications and challenges of flexible batteries in healthcare and various energy storage systems, considering practical implementation, are argued.

PURPOSE: Main insight of the study was to evaluate the potential of Perionyx excavatus, an indigenous earthworm of India towards bioconversion of toxic paper mill wastes. The study had considered a comprehensive study over succession of different enzymes and microbial biomasses alongside removal of heavy metals to reflect the qualitative enrichment of the toxic waste through valorisation procedure. METHODS: The process of vermicomposting was performed using ratio of paper mill sludge: cow dung: straw as 5:4:1 and Perionyx excavatus for a period of 60 days. Qualitative enrichment was considered through detailed evaluation of physicochemical parameters and succession of 19 enzymes using API ZYM technology. Heavy metal loads in terms of Zn, Cr, Cu, Pb along with bioaccumulation factor (BAF) were considered to establish functional role of earthworm in bioremediation. Microbial succession was measured in terms of PLFA biomarkers. RESULTS: Enzymatic enrichment of different isozymes of esterase, aminopeptidase and glycosyl hydrolase were found in the vermicompost. A significant reduction of heavy metals was noticed in vermicomposting of primary sludge as Zn > Pb > Cr > Cu and secondary sludge as Zn > Pb > Cu > Cr. An increase in density of Gram positive bacterial and fungal populations was found at the end phase of vermicomposting process which supports maturity of vermicompost. CONCLUSION: Presence of different enzyme activities, reduction of heavy metal loads along with rise of eukaryotic PLFA markers, had illustrated the efficiency of vermicomposting as a valorisation procedure in the qualitative enrichment of toxic organic paper mill sludge.

In recent years, the paper industry is developing strongly and plays an important role in the industry of our country. Most of the factories have their own wastewater treatment systems. In general, wastewater in paper mill is very difficult to treat and to handle, especially color (Pt–Co) index. In this research, activated carbon with a high surface area and high adsorption capacity was prepared from corn stalks, an agricultural by-products. The suitable conditions of pyrolysis were investigated to prepare activated bio-char from corn stalk. Then, as-obtained carbon material was applied for color treatment of effluent from paper mill. The activated carbon showed high efficiency and capability in color removal of waste water, with the color reduction of 77%.

The present study investigated the adsorption efficiency of laboratory-produced activated carbon (AC) from pyrolysis of mix waste plastic (MWP) for treating paper mill effluent. In the present work, adsorbent was prepared from MWP and was characterized in comparison to commercial adsorbents. A lab scale adsorption study was performed in 100 mL batch experiments to get the optimized condition of different variables by eliminating the pollutants from EOP wastewater and was found as AC dose 10.0 g/100 mL, temperature 35 °C, agitation rate 150 rpm, contact time 7 h, and pH 9.0. The EOP wastewater was analyzed for different quality parameters after treating with prepared AC (PW-AC) and two commercial ACs (SC-AC and M-AC) at optimized conditions. The efficiency of ACs was found to be in order as M-AC>PW-AC>SC-AC. The optimized conditions were applied for the removal of chlorophenols using different ACs in comparison to control EOP wastewater. The study revealed that elimination of chlorophenolic compounds from EOP wastewater (7824 ng/L) was the highest in M-AC treatment followed by PW-AC and SC-AC, i.e., 1426 ng/L, 1759 ng/L, and 2200 ng/L, respectively. PW-AC had major impacts on reduction of chloroguaiacols (82%) as well as chlorophenols (80.7%) that were present in chief amount in EOP wastewater. PW-AC was found to be a capable adsorbent for the removal of chlorophenolic compounds from the most toxic bleaching effluents of pulp and paper industry.

In addition to the large volume, the generated wastewater in paper and cardboard recycling industry contains various organic compounds and dyes. Treatment of these wastewaters is difficult due to t...

A two-step process involving coagulation-flocculation followed by solar photocatalysis – based Advanced Oxidation Process (AOP) using TiO2-Reduced Graphene Oxide (TRGO) nanocomposite as catalyst ha...

There has been an increase in the discovery and usage of sensors for the detection of chemical compounds in the field of analytical chemistry since the last several years. This has led to progressive research in nanotechnology for developing efficient nanomaterials for bio-chemical sensing applications. Thereby, a deft synthesis of silver nanoparticles (Ag NPs) under microwave irradiation was achieved using sodium alginate as a reducing and capping agent in a fast and cost-effective approach. As per the X-ray diffraction analysis, the average particle size of Ag NPs was found to be 10 nm. X-ray photoelectron spectroscpopy analysis showed characteristic peaks at binding energies of 368.10 and 374.11 eV indicating the formation of Ag NPs. The synthesized Ag NPs-alginate composite was further used to develop a paper-based sensor for the detection of H

The discharge of Esparto paper industrial wastewater (EPIW) of SNCPA Company of Kasserine – Tunisia in nature without any treatment can cause harmful effects to the environment. To reduce t...

We present a method to fabricate handcrafted thermoelectric devices on standard office paper substrates. The devices are based on thin films of WS2, Te, and BP (P-type semiconductors) and TiS3 and TiS2 (N-type semiconductors), deposited by simply rubbing powder of these materials against paper. The thermoelectric properties of these semiconducting films revealed maximum Seebeck coefficients of (+1.32 ± 0.27) mV/K and (-0.82 ± 0.15) mV/K for WS2 and TiS3, respectively. Additionally, Peltier elements were fabricated by interconnecting the P-type and N-type films with graphite electrodes. A thermopower value up to 6.11 mV/K was obtained when the Peltier element is constructed with three junctions. The findings of this work show proof-of-concept devices to illustrate the potential application of semiconducting van der Waals materials in future thermoelectric power generation as well as temperature sensing for low-cost disposable electronic devices.

In recent years, the use of microalgae as feedstock for many marketable products, such as animal/aqua feeds, bioplastics and fertilizers, has gained renewed interest due to their fast growth potential coupled with relatively high lipid, carbohydrate and nutrient content. An algal biorefinery at an industrial site has the potential to sustainably and profitably convert carbon dioxide emissions into microalgal biomass and concomitantly reduce nitrogen and phosphorus from wastewaters. Industrial wastewaters are a potential alternative to traditional media used for large-scale microalgal cultivation. Pulp and paper mills are major consumers of water resources and discharge a huge amount of water to nearby lakes or rivers. This study investigated whether pulp and paper mill waste water is suitable for microalgal cultivation with the aim of achieving significant biomass production. Six different process waters from one Canadian pulp and paper mill were tested with two freshwater green microalgae. All of these waters were unable to support growth of microalgae due to inadequate nutrient concentrations, colour, turbidity and possible toxicity issues. HIGHLIGHTS Two freshwater microalgae strains were screened for potential growth on pulp and paper effluents.; Pulp and paper wastewater effluents were unable to support growth of the microalgae.; Chemical residues from the pulping process, such as peroxide and tannin, may inhibit algal growth.

Indigenous plants are widely abundant in Mauritius and if made proper use of, these renewable plants can contribute largely to the local economic sector. This paper assesses the suitability of producing eco-friendly and biodegradable papers using low-cost raw materials by means of fibre from Pandanus utilis’ leaves commonly known as ‘Vacoas’. The leaves were used along with Arundo donax or wastepaper to manufacture composite paper samples in the ratios of 20:80, 40:60, 60:40, 80:20 and 100:0. Chemical pulping was done through Kraft process for a period of 1.5 h at a concentration of 14 wt% NaOH and 4 wt% Na2S at 90 ± 2.5 °C. The mean thickness of the papers was determined to be 0.261 ± 0.027 mm. It was found that the 100% Vacoas fibres had the highest absorbency rate of 1.8 ± 0.5 s followed by the composite A. donax and Vacoas fibre (1.8 ± 0.3 s). The most abrasion resistant paper which also demonstrated the highest burst index of 0.63 kPa m2 g− 1 and tensile index 11.8 N m g− 1 was observed to be that of 100:0 Vacoas fibre paper requiring 35 turns to get abraded followed by the P. utilis and A. donax mix where the 80:20 fibre ratio revealed a high bursting index of 0.45 kPa m2 g− 1 requiring 25 turns to get abraded while 40% P. utilis and 60% A. donax had a high tensile strength of 11.9 N m g− 1. Vacoas to wastepaper mix ratios of 20:80 and 40:60 were found to have the highest mean recovery angles of 61.3 and 59.6°, respectively.

Funding Information: This research was funded by LANXESS-IAB Ionenaustauscher GmbH (Bitterfeld, Germany). Olenka Jibaja Valderrama acknowledges her scholarship granted by the European Commission-Education, Audiovisual, and Culture Executive Agency (EACEA), which allowed her to be part of the Erasmus Mundus Master in Membrane Engineering for a Sustainable World (EM3E-4SW). Acknowledgments: The authors would like to thank LANXESS-IAB Ionenaustauscher GmbH (Bitterfeld-Wolfen, Germany) for the financial support for this research. This work was supported by the Associate Laboratory for Green Chemistry—LAQV, which is financed by national funds from FCT/MCTES (UIDB/50006/2020 and UIDP/50006/2020). Olenka Jibaja Valderrama acknowledges her scholarship grant provided by the European Commission—Education, Audiovisual, and Culture Executive Agency (EACEA), under the program: Erasmus Mundus Master in Membrane Engineering for a Sustainable World-EM3E-4SW (Ed. I, http://em3e-4sw.eu (accessed on 18 August 2021)). Publisher Copyright: © 2021 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (https:// creativecommons.org/licenses/by/ 4.0/). Black liquor is a highly alkaline liquid by-product of the kraft pulping process, rich in organic molecules (hemicelluloses, lignin, and organic acids) and inorganic pulping chemicals such as sodium salts and sulphur-containing compounds. The release of this wastewater without further treatment could have serious environmental and financial implications. Therefore, a costly treatment process is used nowadays. Nanofiltration has been studied in the last few years as a promising alternative to recycle the cooking chemicals required for the separation of lignin and cellulose, but the development of pH-stable membranes with the potential to operate at industrial scales is fundamental in order to make this possible. In this study, the filtration performance of two in-house made membranes is evaluated and compared with a commercial NF membrane to determine the viability of their use for the treatment of black liquor. For this purpose, filtration experiments with simulated black liquor were performed. We identified that Membrane A has the higher potential for this application due to its competitive permeate flux (ca. 24 L m−2 h−1 at a trans-membrane pressure of 21.5 bar), and high rejection of organic components and salts from the cooking liquor (on average, 92.50% for the TOC, 84.10% for the CO32−, 88.70% for the sulphates, 73.21% for the Na+, and 99.99% for the Mg2+). publishersversion published

Paper bleaching effluent was treated by catalytic wet oxidation method and the effect of the type of the catalyst on the efficiency was investigated. Cerium oxide, cobalt oxide and copper oxide based (CuOx-CoOx-CeO2) composite catalysts which were varying with regard to CuOx, CoOx and CeO2 compositions were prepared by co-precipitation method. The efficiency of the process was determined by measuring the chemical oxygen demand (COD), total organic carbon (TOC), adsorbable organic halides (AOX) and Cl− removal yields. When the COD, TOC and AOX removal yields were considered, better results were achieved with copper and ceria based catalysts than the cobalt based catalysts. At the optimum reaction conditions (T—473 K, t—120 min, P—130–250 psig), the maximum removal yields obtained by the 50% CuOx–50% CeO2 catalyst. When the wastewater of the I stage of paper bleaching process was treated, removal yields of TOC, COD and AOX were detected as 89; 94 and 95%, respectively Whereas, removal yields of 53% COD, 84% TOC, 90% AOX and 76% Cl− were achieved for the III stage wastewater. It was shown that removal of the toxicity of wastewater samples that were collected from the paper bleaching process by the proposed treatment methods.

Microbial dehydrogenase activity can help to determine the oxidizing capacity of activated sludge. Here we propose an innovative and automated express-method based on rapid determination of dehydrogenase activity. The measurement is based on the rate of methylene blue reduction by living microbial cells in suspension. A single analysis takes 10 min. The method was adapted for biofilms immobilized on the floating carriers of industrial bioreactors and the kinetics of biological oxidation by activated sludge and biofilms was compared. New parameters were proposed to characterize the biological oxidation under low oxygen levels. The obtained make it possible to quickly determine the dehydrogenase activity of activated sludge and biofilms and promptly monitor the effectiveness of industrial biological wastewater treatment.

A filter paper was functionalized with β-cyclodextrin and citric acid via esterification reaction for the removal of dyes and Cu ions from aqueous solutions. The adsorption capacity and removal performance of the modified filter paper (MFP) was investigated using static and dynamic adsorption experiments. The static adsorption data fit well the Langmuir and pseudo-second-order models, and the adsorption capacity of Methylene Blue (MB), Brilliant Green (BG), Rhodamine-B (RB) and Cu(II) over the MFP were 124.6 mg/g, 130.4 mg/g, 99.7 mg/g and 39.1 mg/g, respectively, which are much higher than the unmodified filter paper (below 2 mg/g). Even better, the decolorization performance and Cu(II) removal of MFP are remarkable in dynamic adsorption. The effluent can reach the National Standard for dyeing and finishing of textile industry of China after three cycles in a continuous filtration-adsorption system. This method provides a new pathway to achieve high efficiency removal of dyes and metal ions from wastewater.

This paper outlines the construction of a White Paper on Geoethics in Forensic Geology. It focuses on forensic geology, although it also relates to the wider sphere of the forensic geosciences. Forensic geology is rapidly evolving to provide assistance in police investigations and in criminal and civil courts with providing scientific advice and evidence, but there also should be associated clear guidelines to benefit both the practitioner and the justice system. Examples of where forensic geology delivers to society in a vital way are required and also where potential malpractice could happen. The paper discusses where forensic geology should pursue social justice in compliance with current legal systems. In order to achieve this goal, it outlines the main areas that we suggest should be developed within the discipline: the competence of the scientist in forensic geology; the creation of best practice guidelines; the establishing of clear duties of the expert in forensic geology; and consideration of ethical aspects in forensic geological activities and ethical aspects in communicating geoscience evidence. When developing geoethics within forensic geology, the following practices were identified as of prime importance: improved standardization of methods; the use of appropriate methods and/or combination of complementary methods; greater clarity of approach used for the location of areas of interest; collection and recovery of evidence; scene examination and sample collection evaluation of data; construction and appropriate use of databases, background information, documentation, cartography and communication of forensic data; and summary of evidence and acknowledgement and consideration of uncertainty and bias. Honesty, integrity, respect, transparency, competence and reliability are vital for the forensic geoscientist to adhere to. Raising the ethical profile of the forensic geoscience profession aims to pave the way for forensic geoscientists to be empowered now and into the future to serve society: acting responsibly and adopting effective ethical codes is vitally important for a safe society. This paper highlights the necessity to hold urgent discussions on the ethical and social implications of forensic geology and their potential repercussions on societal justice. Forensic geology is a very useful tool, but like any other tool in human hands, it presupposes responsibility in its application. Professionalism and honesty in forensic geology are fundamental to assure the public that geoscientists involved have the highest scientific respectability, social credibility and community respect for their role to help pursue judicial truth. The aim of this draft White Paper is to stimulate an open and informed debate on geoethics.

The present study describes the phytoremediation performance of water lettuce (Pistia stratiotes L.) for physicochemical pollutants elimination from paper mill effluent (PME). For this, pot (glass aquarium) experiments were conducted using 0% (BWW: borewell water), 25%, 50%, 75%, and 100% treatments of PME under natural day/light regime. Results of the experiments showed that the highest removal of pH (10.75%), electrical conductivity (EC: 63.82%), total dissolved solids (TDS: 71.20%) biological oxygen demand (BOD: 85.03%), chemical oxygen demand (COD: 80.46%), total Kjeldahl's nitrogen (TKN: 93.03%), phosphorus (P: 85.56%), sodium (Na: 91.89%), potassium (K: 84.04%), calcium (Ca: 84.75%), and magnesium (Mg: 83.62%), most probable number (MPN: 77.63%), and standard plate count (SPC: 74.43%) was noted in 75% treatment of PME after treatment by P. stratiotes. PCA showed the best vector length for TKN, Na, and Ca. The maximum plant growth parameters including, total fresh biomass (81.30 ± 0.28 g), chlorophyll content (3.67 ± 0.05 mg g-1 f.wt), and relative growth rate (0.0051 gg-1 d-1 ) was also measured in 75% PME treatment after phytoremediation experiments. The findings of this study make useful insight into the biological management of PME through plant-based pollutant eradication while leftover biomass may be used as a feedstock for low-cost bioenergy production. PRACTITIONER POINTS: Biological treatment of paper mill effluent using water lettuce is presented. Best reduction of physicochemical and microbiological pollutants was attained in 75% treatment. Maximum production of chlorophyll, plant biomass, and highest growth rate was also observed in 75% treatment.

Cement is widely used for building construction and infrastructural purposes. In the last thirteen years, this product’s global annual production has increased by 78 percent, to 4,200 Mtpa. However, cement factories have been found to be harmful to air quality, plantations, and houses. Dust emission occurs through all the stages of cement production, such as storage, frying, packing, and even in the transportation stage. Cement factories cause environmental contamination worldwide, including in developed countries facing problems related to managing and controlling pollution, and also enforcing stringent legislation to prevent it. By reviewing different studies concerning cement plant emissions, we observed that various mathematical and statistical models have been applied to analyse and determine the effect of these emissions on the environment. Our study is focused on these analytical and statistical methods for analysing gaseous pollutant and particulate matter emissions from various pollution sources, especially cement plants. Identifying the elements of emissions and the development stages of other authors’ analysis methods allowed us to conduct the most precise report possible. Our study also depicts the determinants of these strategies and their advantages, limitations, and implementation variables. The findings of these other studies were discussed, and it was discovered that the output differed depending on the technique used. The frameworks utilised ranged from using a single model to two or more models, in order to compare or combine them. GIS was used as an additional tool to improve the model’s functionality in several studies. Some authors used programming languages such as Python and R to make their models more realistic.

This study examined the responses of a population of brook stickleback (Culaea inconstans) exposed to pulp mill effluent at Jackfish Bay, Lake Superior, Canada, in May 2007 and May 2011. Brook stickleback were extirpated from the effluent-receiving site, presumably due to anoxia after this period. Females at the effluent-receiving site had significantly larger gonad sizes in 2007 and 2011. In 2011, effluent-exposed female gonadal development was significantly advanced when compared with reference sites; they were the second most mature when compared among three different reference sites. Analysis of 7-ethoxyresorufin-O-deethylase activity revealed that effluent-receiving site females had greater CYP1A induction in 2007 and significantly greater CYP1A induction in 2011. Effluent-receiving site males showed significantly reduced CYP1A induction in 2007 and significantly greater induction in 2011. Chemical evaluation of sediment from the receiving environment showed elevated levels of resin acids and the polycyclic aromatic hydrocarbon, retene. Higher condition factors and more mature gonads were consistent with higher winter and spring temperatures modified by effluent or by lake vs. stream environments. Overall, effects on effluent-exposed brook stickleback were not consistent with reported effects in white sucker exposed to the same effluent in previous studies. This article has been made Open Access thanks to the kind support of CAWQ/ACQE (https://www.cawq.ca).