Search

The ITER electron cyclotron emission (ECE) diagnostic system has primary roles in providing measurements of the core electron temperature profile and the electron temperature fluctuation associated with the neoclassical tearing modes. The ITER ECE system includes a radial and oblique line-of-sight. Four 43-meter long low-loss transmission lines (TLs) are designed to transmit millimeter wave power in the frequency range of 70–1000 GHz in both X- and O-mode polarization from the port plug to the ECE instrumentation room in the diagnostic building. The measurement instrumentation includes two Fourier transform spectrometer (FTS) systems and two radiometer systems. The Indian Domestic Agency (IN-DA) and United States Domestic Agency share the responsibility. The IN-DA scope excluding instrumentation and control has passed its preliminary design review and is progressing towards the final design review (FDR). In parallel, the diagnostic integration in different areas is ongoing. Several captive components for the TLs have passed FDR and will be manufactured for installation in the tokamak building soon. A peer review meeting has been held on the prototype hot calibration source, and its integration and new thermal analysis in the diagnostic shield module are continuing. A prototype TL is being tested. A prototype polarizing Martin-Puplett type FTS, operating in the frequency range 70–1000 GHz, features an in-vacuo fast scanning mechanism and a cryo-cooled dual-channel THz detector system. Its performance has been assessed in detail against ITER requirements.

For high-temperature tokamaks like ITER, electron cyclotron emission (ECE) measurements are expected to be affected by many factors like relativistic downshift, harmonics overlap, polarization scra...

The ITER Electron Cyclotron Emission (ECE) diagnostic is progressing towards its Preliminary Design Review (PDR). In parallel, the diagnostic integration in the Equatorial Port is ongoing. Port Integration has to address the structural integrity to withstand various loads, maintenance and the safety aspects of ECE diagnostic. The ITER ECE system includes radial and oblique lines-of-sight. Recently, a successful peer-review of the in-port plug Hot Calibration Source has taken place and its performance and integration feasibility has been demonstrated. Four 45-meter long low-loss transmission lines are designed to transmit mm-wave power in the frequency range of 70- 1000 GHz in both X- and O-mode polarization from the port plug to the ECE instrumentation room in the diagnostic building. Prototype transmission lines are being tested [1]. A prototype polarizing Martin-Puplett type Fourier Transform Spectrometer (FTS) operating in the frequency range 70-1000 GHz, has a fast scanning mechanism and a cryo-cooled dual-channel THz detector system. Its performance has been tested as per ITER requirements. Assessment of the instrumentation and control requirements, functional and non-functional requirements, operation procedures, plant automation are ongoing for the PDR. The current status of the diagnostic, together with integration activities, is presented.

In ITER, an Electron Cyclotron Emission (ECE) diagnostic is planned to measure the electron temperature by measuring the cyclotron radiation in the frequency range of 70-1000 GHz. The cyclotron radiation is usually of low power and needs to be transported with low attenuation over a long distance of ~ 43 m, through a suitable transmission system. Pertaining to long distance, the transmission system will consist of straight waveguide sections, miter bends and waveguide joints. Low power, low loss transmission in a broadband frequency range over long distance makes the design of the transmission system challenging. To arrive at a suitable transmission system, attenuation measurements of three types of transmission lines (TLs) have been performed i.e. circular smooth walled, corrugated and dielectric coated waveguide. A polarizing Michelson interferometer based on Martin-Puplett design has been used to measure the spectrum from waveguide set ups and liquid nitrogen has been used as the black body radiation source. The measured spectrum shows atmospheric water vapour absorption lines in all types of TLs. The preliminary measurement shows that the attenuation of smooth walled waveguide is found to be comparable to corrugated waveguide up to ~ 600GHz and better than corrugated waveguide above 600 GHz for the chosen set of experimental conditions. Further, to avoid water absorption lines, a smooth walled TL is evacuated up to rough vacuum (~10-2mbar) and it was observed that the attenuation is decreased and overall transmission is improved.

The ITER Electron Cyclotron Emission (ECE) diagnostic system will provide information about plasma electron temperature and its fluctuations and other important plasma parameters which are required for plasma control and physics studies. The temperature profile measurement in the first harmonic ECE frequency range from 122-230 GHz (for BT = 5.3 T) is obtained by using an O-mode heterodyne radiometer. It is difficult to cover this wide frequency band by one radiometer, due to technological challenges in achieving wide bandwidth for the mixers. So, the present radiometer design has been optimized by considering four receivers, each of bandwidth ~ 30 GHz which can provide reliable temperature measurements. The splitting of frequency band into four receiver bands is efficiently achieved by considering a combination of quasi-optical and waveguide diplexers, optimizing power loss and cross-talk between the channels. The target spatial resolution of a/30, where "a" is the minor radius of the plasma cross section, is achieved by choosing Radiometer IF filter bandwidth of 1-2 GHz. Further, the radiometer is designed to achieve noise temperature < 10 eV. In this paper, the preliminary design and performance of O-mode Radiometer has been discussed.

The ECE Diagnostic system in ITER will be used for measuring the electron temperature profile evolution, electron temperature fluctuations, the runaway electron spectrum, and the radiated power in the electron cyclotron frequency range (70-1000 GHz), These measurements will be used for advanced real time plasma control (e.g. steering the electron cyclotron heating beams), and physics studies. The scope of the Indian Domestic Agency (IN-DA) is to design and develop the polarizer splitter units; the broadband (70 to 1000 GHz) transmission lines; a high temperature calibration source in the Diagnostics Hall; two Michelson Interferometers (70 to 1000 GHz) and a 122-230 GHz radiometer. The remainder of the ITER ECE diagnostic system is the responsibility of the US domestic agency and the ITER Organization (IO). The design needs to conform to the ITER Organization's strict requirements for reliability, availability, maintainability and inspect-ability. Progress in the design and development of various subsystems and components considering various engineering challenges and solutions will be discussed in this paper. This paper will also highlight how various ECE measurements can enhance understanding of plasma physics in ITER.

The Electron Cyclotron Emission (ECE) diagnostic system in ITER provides essential information for plasma control and for evaluating the plasma performance. It measures the electron temperature profile (edge/core), electron temperature fluctuations and radiated power in the electron cyclotron frequency range from the plasma. Virginia Diodes Inc. (VDI) has designed and developed a state-of-the-art prototype receiver to detect emission in the 200-300 GHz frequency range. The prototype receiver developed by VDI has been tested at DIII-D tokamak to check its performance by measuring higher frequency ECE harmonics in high temperature plasmas. Bench testing verifies the receiver’s band coverage and noise temperatures. Good sensitivity has been obtained meeting the ITER requirement. Also, the receiver performance is assessed for ITER by comparing the data from the receiver and the existing Michelson interferometer for the same DIII-D plasma shot. The measurement results show that the receiver provides accurate temperature information for the plasma emission throughout the frequency band.

Considerable progress has been made on the design of the ITER electron cyclotron emission (ECE) diagnostic over the past two years. Radial and oblique views are still included in the design in order to measure distortions in the electron momentum distribution, but the oblique view has been redirected to reduce stray millimeter radiation from the electron cyclotron heating system. A major challenge has been designing the 1000 K calibration sources and remotely activated mirrors located in the ECE diagnostic shield module (DSM) in the equatorial port plug #09. These critical systems are being modeled and prototypes are being developed. Providing adequate neutron shielding in the DSM while allowing sufficient space for optical components is also a significant challenge. Four 45-meter long low-loss transmission lines transport the 70–1000 GHz ECE from the DSM to the ECE instrumentation room. Prototype transmission lines are being tested, as are the polarization splitter modules that separate O-mode and X-mode polarized ECE. A highly integrated prototype 200–300 GHz radiometer is being tested on the DIII-D tokamak in the USA. Design activities also include integration of ECE signals into the ITER plasma control system and determining the hardware and software architecture needed to control and calibrate the ECE instruments.