Search

A novel concept of acoustic fiber Bragg grating (AFBG) was conceived and experimentally validated as an effective technique for high-temperature sensing. Similar to the well-known optical fiber Bragg grating, the AFBG employs interactions between waves and periodic structures on an elongated waveguide. Acoustic waves reflected from periodic structures interfere with each other and result in the emergence of resonance frequency when acoustic wavelength matches with pitch length of the periodic structures. When the single-mode operation condition is satisfied, the resonance frequency location can be accurately resolved and thus be used as an effective indicator for temperature sensing. To demonstrate this concept, an AFBG sample was fabricated on a telecommunication optical fiber (125- $\mu \text{m}$ diameter) with femtosecond laser micromachining setup, and it demonstrated sensing capability up to 700 °C, which was limited by the fiber material (fused silica) and could be over 1400 °C if other material, such as sapphire, was used as the waveguide. With the features of various applicable material, low system cost, and potential multiplexing capability, this AFBG technology is a promising candidate for high-temperature sensing, even in a distributed manner.

Fiber Bragg gratings (FBGs) in the center of multimode microfibers (MM-MF) with 10μm diameter were successfully inscribed with point-by-point method and their reflection spectra show peaks over 10dB signal-to-noise ratio (SNR) and less than 0.5nm bandwidth. FBGs on regular size multimode fiber (~60μm core size) shows nearly continuous reflection spectrum. However, when the diameter of the multimode fiber is reduced to ~10μm, its modal volume significantly decreases so that the remaining optical modes are separated by larger propagation constant difference, resulting distinguishable sharp peaks on FBG reflection spectrum. Therefore, MM-MF based FBGs could be practical sensors for simultaneous multi-parameters with outstanding sensitivity and accuracy.

We report a different mechanism for rotation sensing by analyzing the polarization of light exiting from a Sagnac loop. Unlike in an interferometric fiber optic gyroscope (I-FOG), here the counter-propagating waves in the Sagnac loop are orthogonally polarized at the loop exit and, consequently, cannot directly interfere with each other when recombined at the exit. We show that the Stokes parameters s2 and s3 of the combined waves are simply the cosine and sine functions of the phase difference between the counter propagation waves, which is linearly proportional to the rotation rate, allowing precise determination of the rotation rate by polarization analysis. We build such a proof-of-concept polarimetry FOG and achieved key performance parameters comparable to those of a high-end tactical-grade gyroscope. In particular, the device shows a bias instability of 0.09°/h and an angular random walk of 0.0015°/h, with an unlimited dynamic range, demonstrating its potential use for rotation sensing. This new approach eliminates the need for phase modulation required in I-FOGs, and promotes easy photonics integration, enabling the development of low-cost FOGs for price-sensitive applications, such as autonomous and robotic vehicles.

Compact ferrule-top nanomechanical resonators with multilayer graphene (MLG) diaphragms as vibrating elements are demonstrated. The resonators comprise a suspended MLG film supported by a ceramic ferrule with a bore diameter of ∼125 μm. The mechanical resonance of the graphene film is excited and detected by an all-fiber optical interrogation system. Based on a beam-shape graphene mechanical resonator, a force sensitivity of ∼3.8 fN/Hz1/2 was theoretically predicted. The integration of nanomechanical graphene film with optical fiber simplifies the excitation and interrogation of the resonator and would allow the development of practical fiber-optic sensors for force, mass, and pressure measurements.

In this paper we propose a new and cost-effective fabrication scheme for porous polymer optical fibers. Different porous polymer fibers made from polycarbonate (PC) and poly(methyl methacrylate) (PMMA) using this method have been thermally drawn and characterized. Porosity in the fiber cladding is introduced by the absorbed water in one layer of the polymer fiber preforms under heat treatment and/or thermal drawing, and can be controlled by adjusting the water concentration. In addition, we have shown that the fabricated porous polymer fibers have the potential application in localized drug delivery for cancer treatment.

We present a large-core single-mode “windmill” single crystal sapphire optical fiber (SCSF) design, which exhibits single-mode operation by stripping off the higher-order modes (HOMs) while maintaining the fundamental mode. The “windmill” SCSF design was analyzed using the finite element analysis method, in which all the HOMs are leaky. The numerical simulation results show single-mode operation in the spectral range from 0.4 to 2 μm in the windmill SCSF, with an effective core diameter as large as 14 μm. Such fiber is expected to improve the performance of many of the current sapphire fiber optic sensor structures.

A new type of single crystal sapphire optical fiber (SCSF) design is proposed to reduce the number of guided modes via a highly dispersive cladding with a periodic array of high and low index regions in the azimuthal direction. The structure retains a “core” region of pure single crystal (SC) sapphire in the center of the fiber and a “cladding” region of alternating layers of air and SC sapphire in the azimuthal direction that is uniform in the radial direction. The modal characteristics and confinement losses of the fundamental mode were analyzed via the finite element method by varying the effective core diameter and the dimensions of the “windmill” shaped cladding. The simulation results showed that the number of guided modes were significantly reduced in the “windmill” fiber design, as the radial dimension of the air and SC sapphire cladding regions increase with corresponding decrease in the azimuthal dimension. It is anticipated that the “windmill” SCSF will readily improve the performance of current fiber optic sensors in the harsh environment and potentially enable those that were limited by the extremely large modal volume of unclad SCSF.

We report the fabrication of in-line photonic microcells (PMCs) by encapsulating tapered microfibers (MFs) inside glass tubes. The encapsulation isolates MFs from external environment and makes them more suitable for real-world applications. Based on PMCs with encapsulated highly birefringent (Hi-Bi) MFs, we demonstrated pressure, temperature and refractive index (RI) sensors as well as long period grating devices. A fiber Sagnac loop interferometer incorporating a Hi-Bi microfiber PMC demonstrated RI sensitivity of 2024 nm per RI unit (nm/RIU) in gaseous environment and 21231 nm/RIU in water.