Search

Improving fuel economy of gasoline-powered vehicles is of great importance for achieving carbon neutrality of the society. The present paper deals with a concept study of a series hybrid powertrain to reduce CO2 emissions as much as possible, considering both engine and vehicle key performances. The study utilized model-based research using 0D/1D/3D-CAE and DOE optimization techniques. The ICE simulation shows >47% break thermal efficiency under restrictions from combustion noise level and tail pipe emissions. In terms of series hybrid powertrain vehicle fuel economy, ICE power in generation for best fuel economy shall be optimized according to the given battery capacity. Also, short-term future driving power demands information may help reasonable ICE activation through the transient driving cycle. [ABSTRACT FROM AUTHOR]

The Miller cycle is a program that effectively reduces NOx emissions from marine diesel engines by lowering the maximum combustion temperature in the cylinder, thereby reducing NOx emissions. To effectively investigate the impact of Miller cycle optimum combustion performance and emission capability under high load conditions, this study will perform a one-dimensional simulation of the performance of a marine diesel engine, as well as a three-dimensional simulation of the combustion in the cylinder. A 6-cylinder four-stroke single-stage supercharged diesel engine is taken as the research object. The chassis dynamometer and other related equipment are used to build the test system, carry out the diesel engine bench test, and collect experimental data. The simulation results are compared with the test results, and the error is less than 5%. In this study, the authors will use simulation software to simulate several Miller cycle scenarios designed for early inlet valve closure and analyze the impact of the Miller cycle on combustion and emissions at 100% load conditions. By comparing the flow field distribution of the engine at 1500 r/min condition, it was found that proper EIVC can prolong the ignition latency period and homogeneous fuel-air mixture combustion acceleration, but it can reduce pressure and temperature within the piston chamber and NOx emission. However, the Miller cycle reduces end-of-compression temperatures, which increases combustion duration and exhaust temperatures, making it difficult to improve fuel economy at the optimum fuel consumption point, and closing the intake valves prematurely leads to excessive fuel expenditure. Furthermore, temperature and heat release rate within the piston chamber, NOx, and SOOT generation were significantly enhanced. [ABSTRACT FROM AUTHOR]

An investigation into the lips-guided-flow combustion chamber (LGFC) and Miller cycle was conducted on a highly intensified diesel engine under rated power conditions to improve thermal efficiency. The radius and depth of the chamber bowl and lips were optimized to intensify the guided flow and fuel/air mixing. The experimental and simulated results show that the LGFC had a higher fuel/air mixture quality and quicker combustion rate, leading to a higher indicated power and higher thermal efficiency. A late intake valve closing (LIVC) Miller cycle with a higher expansion ratio of 11 and a lower compression ratio of 8.2 was used to control the energy distribution of the thermodynamic cycle and reduce the mechanical and thermal loads. The results show that the maximum combustion temperature was decreased by about 45 K and the thermal efficiency was improved by 2.1%. The research results are useful to guide the improvement in thermal efficiency through combustion chamber design and Miller cycle application for highly intensified diesel engines. [ABSTRACT FROM AUTHOR]

The selection of optimal measures for reducing the environmental impact of diesel engines is considered. The relative variation in the fuel consumption and nitrogen oxide emissions is studied for the 4400‑kW 12FT26.5/31 engine (produced by Kolomensky Zavod). The proposed selection strategy may be used in development tests of new engine designs. [ABSTRACT FROM AUTHOR]

Increased compression ratio of auto engine can effectively improve thermal efficiency. However, the risk of engine knock becomes higher when increasing the intake boosting. In this paper, the role of an inlet Water Injection (WI) system in improving the performance of a spark ignition engine was investigated, which was through a comparative study of Miller cycle with electromagnetic intake valve train (EMIT). The numerical simulation method was developed in AVL BOOST based on the engine test rig, and then the port water injection modelling was introduced. The results showed that when the engine speed was lower than 1800 r/min, the water spray scheme had a better effect on the engine performance as compared with the Miller cycle, and such advantage was increasingly significant with the decrease of the speed. This is due to the fact that the water injection takes into account the temperature reduction in the cylinder. When the engine speed was over 1800 r/min, it had a negative impact on engine performance with IWI due to the excessive suppression of combustion. This study provides a theoretical basis for design and research of gasoline engines. [ABSTRACT FROM AUTHOR]

Variable valve timing (VVT) and Miller cycle are advanced technologies employed to optimize engine performance by improving airflow exchange, which are seldom investigated based on the direct-injection (DI) hydrogen engine. The objective of this study is to assess the effects of intake valve closing (IVC) and exhaust valve opening (EVO) timing on the gas exchange performance, combustion, and emissions of a DI hydrogen engine, after which a synergistic control strategy of IVC and EVO timing is proposed. This work is conducted under wide-open throttle and 1500 rpm. The results indicate that the synergistic control of IVC and EVO timing can increase volumetric efficiency by more than 40%, enhance gas exchange performance, shorten combustion duration, and reduce cyclic variation, resulting in approximately 43.15% brake thermal efficiency. Furthermore, brake mean effective pressure can be increased by more than 60% and NO emissions are controlled to less than 20 ppm by optimizing valve timings. • A synergistic control strategy of intake and exhaust VVT is proposed. • The airflow exchange and combustion of a DI hydrogen engine are optimized. • The regulation of valve timings can improve gas exchange performance. • The engine can reach 43.15% maximum brake thermal efficiency. [ABSTRACT FROM AUTHOR]

Aiming to further improve the thermal efficiency and reduce NO x emissions in the stoichiometric hydrogen-enriched natural gas (NG) engine, a detailed 3-D simulation model of stoichiometric operation heavy-duty NG engine is built based on the actual boundary conditions from high load bench test. The superimposed methods for knock regulation, combustion and emission control, including Miller valve timing, hydrogen volume fraction and EGR rate were proposed and investigated comprehensively. It reveals that the typically bimodal characteristic of heat release rate (HRR) curve is caused by knock, which seriously restricts the performance improvement of stoichiometric NG engine under high load condition. To predict and control the occurrence of the second peak of HHR accurately, a new parameter BI is defined. Moreover, the Miller timing with 20°CA of the intake valve late closing shows better combustion performance within the knock limit, accompanied by a slight increase in NO x emissions. Additionally, the 5% hydrogen blend, coupled with the Miller cycle, can further enhance the indicated thermal efficiency (ITE) of the NG engine due to the stronger effects on acceleration of laminar flame propagation velocity than the promotion of end-gas auto-ignition. Besides, the great potential of EGR rate for balancing NO x and ITE is also confirmed in the heavy-duty hydrogen-enriched NG engine adopting Miller cycle. Compared to the original indexes, combing with the regulation strategies of intake valve late closing (20°CA), hydrogen addition (5%) and EGR (17%) are proved to increase the indicated thermal efficiency by 1.89% and reduce NO x emissions by 11.47% within the knock limit. • The superimposed effects of Miller cycle, hydrogen addition and EGR rate on knock, combustion and emission are explored. • A new parameter is proposed for predicting and controlling the occurrence of the second peak of HRR due to knock. • The potential of hydrogen addition in improving thermal efficiency considering the knock is investigated. • Higher EGR ratio within the knock limitation can effectively suppress NO X emissions and improve thermal efficiency. [ABSTRACT FROM AUTHOR]

Diesel engines play a very significant role in the automotive industry, but the total emissions of diesel engines are more than 1.8 times that of petrol engines. It is therefore important for diesel engines to control emissions. Theoretically, the Miller cycle can be used to achieve NOx reductions by changing the effective compression ratio, while it has become increasingly popular in recent years with the increasing maturity of current turbocharging technology. Based on Ricardo WAVE software, this paper analyses the NOx emissions and engine performance of diesel engines by modelling and simulating their operation under different loads with two types of Miller cycles (EIVC and LIVC) at different degrees. Simulation of engines operating under different loads allows a more comprehensive study of the effects of the Miller cycle on the engine, and a specific analysis in the context of the actual engine operating environment. The result is that both versions of the Miller cycle are most effective in reducing NOx emissions at 10% load, showing a maximum reduction of 21% for EIVC and 37% for LIVC. However, as the Miller cycle decreases engine power, the paper further investigates the application of turbocharger systems in the EIVC Miller cycle, with results showing a 32% increase in brake power at 10% load and −25% EIVC Miller cycle degree. Both ethanol-fueled diesel-cycle and Miller cycle engines were also analyzed, and a reduction in NOx emissions was observed, as well as hydrogen engine performance and NOx emissions. [ABSTRACT FROM AUTHOR]

To meet the requirements of increasing stringent emission regulations, innovative solutions are adopted to reduce NOx emissions from diesel engines. In this study, the GT-Power software was utilized to investigate NOx control possibility of Miller cycle in combination with exhaust gas recirculation (EGR) and post-injection in a diesel engine. The results indicate early intake valve closing reduced compression work, resulting in a power increase of 0.3 kW. Furthermore, the cooling effect of Miller cycle lowered maximum temperature by 24.5 K and NOx emissions by 17.4%. Miller cycle and EGR combination was able to lower NOx emissions by 83.7%, although it resulted in higher Soot emissions. Adding post-injection help to mitigate this issue, lowering NOx emissions by over 20% and Soot emissions by 5.8%. Finally, the combination of MD75 + 12% EGR +2.5 mg post-injection mass at 34°CA ATDC achieved a 76.1% reduction in NOx emissions with only a 2.6% impact on brake power using modeFRONTIER for multi-objective optimization. [ABSTRACT FROM AUTHOR]

To meet the requirements of increasing stringent emission regulations, innovative solutions are adopted to reduce NOx emissions from diesel engines. In this study, the GT-Power software was utilized to investigate NOx control possibility of Miller cycle in combination with exhaust gas recirculation (EGR) and post-injection in a diesel engine. The results indicate early intake valve closing reduced compression work, resulting in a power increase of 0.3 kW. Furthermore, the cooling effect of Miller cycle lowered maximum temperature by 24.5 K and NOx emissions by 17.4%. Miller cycle and EGR combination was able to lower NOx emissions by 83.7%, although it resulted in higher Soot emissions. Adding post-injection help to mitigate this issue, lowering NOx emissions by over 20% and Soot emissions by 5.8%. Finally, the combination of MD75 + 12% EGR +2.5 mg post-injection mass at 34°CA ATDC achieved a 76.1% reduction in NOx emissions with only a 2.6% impact on brake power using modeFRONTIER for multi-objective optimization. [ABSTRACT FROM AUTHOR]

This study experimentally investigates the impact of extreme Miller cycle strategies paired with high intake manifold pressures on the combustion process, emissions, and thermal efficiency of heavy-duty diesel engines. Well-controlled experiments isolating the effect of Miller cycle strategies on the combustion process were conducted at constant engine speed and load (1160 rpm, 1.76 MPa net IMEP) on a single cylinder research engine equipped with a fully-flexible hydraulic valve train system. Late intake valve closing (LIVC) timing strategies were compared to a conventional intake valve profile under either constant cylinder composition, constant engine-out NOx emission, or constant overall turbocharger efficiency ( η TC ) to investigate the operating constraints that favor Miller cycle operation over the baseline strategy. Utilizing high boost with conventional intake valve closing timing resulted in improved fuel consumption at the expense of sharp increases in peak cylinder pressures, engine-out NOx emissions, and reduced exhaust temperatures. Miller cycle without EGR at constant λ demonstrated LIVC strategies effectively reduce engine-out NOx emissions by up to 35%. However, Miller cycle associated with very aggressive LIVC timings led to fuel consumption penalties due to increased pumping work and exhaust enthalpy. LIVC strategies allowed for increased charge dilution at the baseline NOx constraint of 3.2 g/kWh, resulting in significant fuel consumption benefits over the baseline case without compromising exhaust temperatures or peak cylinder pressures. As Miller cycle implementation was shown to affect the boundary conditions dictating η TC , the LIVC and conventional IVC cases were studied at an equivalent η TC point representative of high boost operation. With high boost, LIVC yielded reduced NOx emissions, reduced peak cylinder pressures, and elevated exhaust temperatures compared to the conventional IVC case without compromising fuel consumption. [ABSTRACT FROM AUTHOR]

Thermal efficiency and power density improvement are the main research foci of the literature on diesel engines. The Miller cycle is considered to be one of the most promising methods of diesel engine operation. In this study, a fully variable valve timing and lift mechanism (CD-HFVVS) was studied to determine the possibility of a Miller operation. Firstly, the valve seat impact buffer in the mechanism was tested, which proved that the buffer can effectively eliminate the valve seat impact. Then the influences of different speeds and oil temperatures were studied. The results show that the valve opening duration is prolonged when engine speed increases, and the valve lift and duration are reduced while the oil temperature increased. The valve timing and lift can be fully adjusted by changing the oil discharge position and the initial plunger position, which further proves that CD-HFVVS can achieve the performance optimization of the Miller cycle. By using the mechanism, a single cylinder test was performed. By using variable inlet valve timing, the fuel efficiency can be effectively improved and the peak pressure and in-cylinder average temperature can both be suppressed. [ABSTRACT FROM AUTHOR]

Using a combined energy cycle based on conventional and/ or clean energy sources can be a suitable option to dominate the limitations in the field of energy. Meanwhile, the select of the prime power source in such processes is a challengeable issue. The selection of the prime power source from renewable sources and in addition the use of system waste heat can lead to enhance power generation. In the present work, an energy system based on conventional energy sources and clean technology is introduced and investigated. The new integrated hybrid energy cycle is composed of Miller cycle engine (MC), alkaline fuel cell (AFC), alkaline electrolyzer, Organic Rankine cycle (ORC) system and Stirling engine. MC and AFC are used as the main power sources of the cycle. On the other hand, ORC and Stirling engine for generating more electricity from the waste heat of the cycle are applied. The electrolyzer embedded in the cycle receives its electricity from the MC and provides the required inputs of the AFC. Although many studies had been done on the integration of various power generation sources with different energy cycles, attempts had not been done to establish a study on the hybrid of MC, AFC, alkaline electrolyzer, Stirling engine and ORC to produce additional electricity. Results revealed that the introduced energy system generates 3.75 kW of electric power. The portion of MC, fuel cell, ORC, and Stirling engine in electric power production is 71.2, 10.8, 9.5 and 8.5%, respectively. However, the alkaline electrolyzer consumes 2.06 kW of power and generates 48.2 g/h of H2fuel. It was also found that the cycle exergy destruction is 3.34 kW. In addition, the use of MC and AFC heat dissipation heat can enhance power generation.

The article is devoted to the study of the possibilities of improving the technical and economic indicators of an internal combustion engine (ICE) through the use of the Miller cycle with a shortened intake. A review of scientific works on the use of the Atkinson cycle and Miller cycle in an internal combustion engine is carried out. A comparative analysis of theoretical cycles: Otto cycle, Atkinson cycle and Miller cycle is carried out. Calculated studies of the influence of the expansion ratio and the pressure increase ratio on the efficiency of the Atkinson cycle have been carried out. The ratios are presented that allow using the Miller cycle with a short inlet to obtain the same theoretical efficiency of the cycle as that of the Atkinson cycle. At the same time, the implementation of the Miller cycle in a real engine design significantly exceeds the possibilities of using the Atkinson cycle. The results of the study showed that the use of the Miller cycle with a shortened intake is preferable, but it must necessarily increase the compression ratio and intake pressure through the use of boost. On the example of real data of the main parameters of the cycle, it is shown that the use of the theoretical Miller cycle can provide a significant up to 12.2% increase in the efficiency of the cycle compared to the Otto cycle. The ratios, conditions and recommendations are presented that allow the effective use of the Miller cycle with a shortened intake in a real engine design.

Copyright of Journal of Shanghai University of Engineering Science / Shanghai Gongcheng Jishu Daxue Xuebao is the property of Journal of Shanghai University of Engineering Science Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Journal of Central South University is the property of Springer Nature and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This paper introduces the theoretical basis and optimization method of diesel engine working process theory. By comparing two Miller cycle schemes of B20 biodiesel under different load conditions of 1000 rpm (100%, 75%, and 50%), the best Miller cycle scheme and the best Miller degree were found. Then, based on the Miller cycle scheme, its performance was optimized and analyzed, and the best intake timing scheme of the B20 biodiesel engine under different working conditions was obtained. The results show that the performance of B20 biodiesel in variable valve overlap angle Miller cycle is better than that in variable cam profile Miller cycle, and the effect is the best when the Miller degree is 30 °CA. When B20 biodiesel is used under 100% and 50% load conditions, the maximum power under the two loads is in the area near intake valve timing 179 °CAA and exhaust valve timing 174 °CAA, and intake valve timing 224.5 °CAA and exhaust valve timing 119 °CAA, respectively. Fuel consumption, soot emissions, and NOx emissions also have the corresponding best performance intake valve and exhaust valve positions. [ABSTRACT FROM AUTHOR]

This paper assesses the effect of the Miller cycle upon the internal aerodynamics of a motored transparent spark ignition engine via CFD simulation and particle image velocimetry. Since the transparent Miller engine does not allow for measurements in the roof of the combustion chamber, the extraction of information regarding the aerodynamic phenomena occurring here is based on CFD simulation, i.e., the results of the CFD simulation are used to allow for the extrapolation of the experimental data; thus, they are used to complete the picture regarding the aerodynamic phenomena occurring inside the whole cylinder. The results indicate that implementing the early intake valve closing strategy to obtain the Miller cycle has a negative impact on the mean kinetic energy, turbulent kinetic energy, and fluctuating velocity toward the end of the compression stroke, thus affecting, the combustion process. This supports the need to intensify the internal aerodynamics when applying the Miller cycle such that the turbulence degradation is not too big and, consequently, to still gain efficiency in the Miller cycle. [ABSTRACT FROM AUTHOR]

In this study, a one-dimensional simulation was performed to evaluate the performance of in-cylinder combustion to control NOx emissions on a four-stroke, six-cylinder marine medium-speed diesel engine. Reducing the combustion temperature is an important in-cylinder measure to decrease NOx emissions of marine diesel engines. The Miller cycle is an effective method used to reduce the maximum combustion temperature in a cylinder and accordingly decrease NOx emissions. Therefore, the authors of this study designed seven different early intake valve closing (EIVC) Miller cycles for the original engine, and analyzed the cycle effects on combustions and emissions in high-load conditions. The results indicate that the temperature in the cylinder was significantly reduced, whereas fuel consumption was almost unchanged. When the IVC was properly advanced, the ignition delay period increased and the premixed combustion accelerated, but the in-cylinder average pressure, temperature and NOx emissions in the cylinder were lower than the original engine. However, closing the intake valve too early led to high fuel consumption. In addition, the NOx emissions, in-cylinder temperature, and heat release rate remarkably increased. Therefore, the optimal timing of the EIVC varied with different loads. The higher the load was, the earlier the best advance angle appeared. Therefore, the Miller cycle is an effective method for in-engine NOx purification and does not entail significant cost. [ABSTRACT FROM AUTHOR]

A numerical method is used to investigate the effect of variation Miller cycle and Exhaust gas recirculation (EGR) on fuel economy and combustion characteristics of a turbocharged gasoline direct-injection (GDI) engine, in which one-dimensional (1D) and three-dimensional (3D) model are established in GT-Power and CONVERGE software, respectively. The simulation values of the model are validated well with experimental results at part load and full load conditions. The results demonstrate that fuel economy is improved with Miller degree increasing at 50% loads because of the reduction of pumping loss. Further studies have shown that, especially at ±58°CA Miller degrees, early intake valve closure (EIVC) has a better performance than late intake valve closure (LIVC) on fuel economy. In addition, EGR can further decrease fuel consumption based on miller cycle because of further decline for pumping loss and combustion phase optimization. Meanwhile, LIVC can match wider EGR rates than EIVC in terms of good fuel economy. Compared to the baseline scheme, the brake specific fuel consumption is reduced by 4.3% with LIVC58 + 7% EGR. And combustion process of the LIVC58 + 7% EGR also gets optimized which result in lower maximum in-cylinder temperature due to the advance of CA50 and delay of combustion duration. [ABSTRACT FROM AUTHOR]

Diesel engines play a very significant role in the automotive industry, but the total emissions of diesel engines are more than 1.8 times that of petrol engines. It is therefore important for diesel engines to control emissions. Theoretically, the Miller cycle can be used to achieve NOx reductions by changing the effective compression ratio, while it has become increasingly popular in recent years with the increasing maturity of current turbocharging technology. Based on Ricardo WAVE software, this paper analyses the NOx emissions and engine performance of diesel engines by modelling and simulating their operation under different loads with two types of Miller cycles (EIVC and LIVC) at different degrees. Simulation of engines operating under different loads allows a more comprehensive study of the effects of the Miller cycle on the engine, and a specific analysis in the context of the actual engine operating environment. The result is that both versions of the Miller cycle are most effective in reducing NOx emissions at 10% load, showing a maximum reduction of 21% for EIVC and 37% for LIVC. However, as the Miller cycle decreases engine power, the paper further investigates the application of turbocharger systems in the EIVC Miller cycle, with results showing a 32% increase in brake power at 10% load and −25% EIVC Miller cycle degree. Both ethanol-fueled diesel-cycle and Miller cycle engines were also analyzed, and a reduction in NOx emissions was observed, as well as hydrogen engine performance and NOx emissions.

Thermal efficiency and power density improvement are the main research foci of the literature on diesel engines. The Miller cycle is considered to be one of the most promising methods of diesel engine operation. In this study, a fully variable valve timing and lift mechanism (CD-HFVVS) was studied to determine the possibility of a Miller operation. Firstly, the valve seat impact buffer in the mechanism was tested, which proved that the buffer can effectively eliminate the valve seat impact. Then the influences of different speeds and oil temperatures were studied. The results show that the valve opening duration is prolonged when engine speed increases, and the valve lift and duration are reduced while the oil temperature increased. The valve timing and lift can be fully adjusted by changing the oil discharge position and the initial plunger position, which further proves that CD-HFVVS can achieve the performance optimization of the Miller cycle. By using the mechanism, a single cylinder test was performed. By using variable inlet valve timing, the fuel efficiency can be effectively improved and the peak pressure and in-cylinder average temperature can both be suppressed.

Legislations concerning emissions from heavy-duty diesel engines are becoming increasingly stringent. This requires conventional diesel combustion to be compliant using costly and sophisticated aftertreatment systems. Preferably, diesel–methanol dual-fuel is one of the suitable alternative combustion modes as it can potentially reduce the formation of nitrogen oxide and soot emissions which characterised the diesel mixing-controlled combustion. This is primarily due to the high latent heat of vaporisation and oxygen content of the methanol fuel. At high engine loads, however, the potential of diesel–methanol dual-fuel operation is constrained by the excessive combustion pressure rise rate and peak in-cylinder pressure, which limits both the engine efficiency and the percentage of methanol that can be used. For the first time, experimental studies were conducted to explore advanced combustion control strategies such as Miller cycle, exhaust gas recirculation, and intake air cooling for improving upon high load diesel–methanol dual-fuel combustion. Experiments were carried out at 1200 r/min and 18 bar indicated mean effective pressure on a single-cylinder heavy-duty diesel engine, which equipped with a high pressure common rail diesel injection, a methanol port fuel injection, and a variable valve actuation system on the intake camshaft. Results showed that the methanol energy fraction of a conventional diesel–methanol dual-fuel operation with a baseline intake valve closing timing was limited to 28%. This was due to the high combustion temperature at a high load which advanced the ignition timing of the premixed charge, resulting in high levels of pressure rise rate. The application of lower effective compression ratio and intake air temperature (Tint) effectively decreased the compression temperature, which successfully delayed the ignition timing of the premixed charge. This allowed for a more advanced diesel injection timing to achieve improvement in the thermal efficiency and potentially enabled a higher methanol substitution ratio. Although the introduction of exhaust gas recirculation demonstrated very slight impact on the ignition timing of the premixed charge, a higher net indicated efficiency was observed due to a relatively lower local combustion temperature which reduced heat transfer loss. Moreover, the optimised diesel–methanol dual-fuel operation allowed a higher methanol energy fraction of 40% to be used at an effective compression ratio of 14.3 and Tint of 305 K and achieved the highest net indicated efficiency of 47.4%, improving by 3.7% and 2.6%, respectively, when compared to the optimised conventional diesel combustion (45.7%) and conventional diesel–methanol dual-fuel (46.2%). This improvement was accompanied with a reduction of 37% in nitrogen oxide emissions and little impact on soot emissions in comparison with the conventional diesel combustion. [ABSTRACT FROM AUTHOR]

The Miller cycle has significant advantages of suppressing knocking and improving nitrogen oxide (NO X) emissions without the penalties of reducing engine fuel consumption and power output. In the study, the effect of non-Miller cycle and Miller cycle on the exhaust gas recirculation (EGR) introduction capability and the knocking boundary were evaluated on a stoichiometric combustion natural gas engine at three different loads. Additionally, the effect of Miller cycle coupled EGR and ignition timing on engine performance and combustion process was discussed. The results indicate that, for the same condition, the Miller cycle could reduce peak temperature and pressure, increased combustion duration, and delayed combustion phase, which makes for effective knocking suppression. Therefore, the Miller cycle has less dependence on the EGR strategy to control knock. Moreover, the Miller cycle can also reduce the ability to introduce EGR, which could up to 3.8%. By matching the ignition timing and EGR rate, the BSFC of the Miller cycle were decreased by 0.6g/kW·h, 2.4 g/kW·h and 2.9 g/kW·h respectively for three test conditions compared with non-Miller cycle. In terms of emissions, the Miller cycle and EGR can both suppress NO X emissions, while the EGR being more effective. The study will provide valid information for the application of the Miller cycle to achieve efficiency clean combustion of natural gas engine. • The effect of different cycles on the boundary parameters of the engine is compared. • The effect of the Miller cycle on the combustion process of the engine is investigated. • The potential for optimizing fuel economy and improving NO X emissions of Miller cycle coupled EGR is explored. [ABSTRACT FROM AUTHOR]

Previous studies have shown that increase compression ratio (CR) is an effective way to improve thermal efficiency of gasoline engine without changing the mechanical structure and working cycle, however, it is limited by engine knock when increasing the intake boosting under high load operation. This study aimed to solve the knock problem of gasoline engine with higher CR by application of Miller cycle, which can be implemented by either early or late intake valve closing (EIVC or LIVC). Therefore, in this paper, based on the engine with CR of 13.5 and electromagnetic valves train (EMVT), a comparative study was carried out to investigate the effects of EIVC and LIVC on engine performance, by theoretical modeling and calculation. The results show that, at high load, EIVC strategy is more preferred than LIVC owing to its lower total power consumption, which can improve the indicated mean effective pressure (IMEP) by 0.0371 bar, while enhance turbulence intensity and improve combustion. And at part load, the advantage for EIVC declines gradually, nevertheless, it can still sensitively adjust the EGR rate and thus reduce NOx. This results of quantitative analysis about two Miller cycles can provide valuable reference for engine designers and researchers. [ABSTRACT FROM AUTHOR]

This paper assesses the effect of the Miller cycle upon the internal aerodynamics of a motored transparent spark ignition engine via CFD simulation and particle image velocimetry. Since the transparent Miller engine does not allow for measurements in the roof of the combustion chamber, the extraction of information regarding the aerodynamic phenomena occurring here is based on CFD simulation, i.e., the results of the CFD simulation are used to allow for the extrapolation of the experimental data; thus, they are used to complete the picture regarding the aerodynamic phenomena occurring inside the whole cylinder. The results indicate that implementing the early intake valve closing strategy to obtain the Miller cycle has a negative impact on the mean kinetic energy, turbulent kinetic energy, and fluctuating velocity toward the end of the compression stroke, thus affecting, the combustion process. This supports the need to intensify the internal aerodynamics when applying the Miller cycle such that the turbulence degradation is not too big and, consequently, to still gain efficiency in the Miller cycle.

In this paper, validated simulations using Ricardo WAVE have been performed to investigate the effect of the Miller cycle and low-carbon fuels on the performance (power, torque, BTE and BSFC) and emissions of a diesel engine. The results show that the increased Miller cycle effect (larger deviation of the advanced or retarded intake valve closing from the standard intake valve closing time) will decrease NOx, CO and HC emissions, and slightly improve brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC) with slight loss in engine performance and increase in soot emissions. An engine running B0 (diesel with 0% Biodiesel in the blend) with a −18% Miller cycle effect has a reduction in NOx of 9% and CO of 4.3% with a decrease of 1.6% in power at the rated engine speed. Using low carbon fuels drastically reduces emissions with reduced BTE and increased BSFC. When used in conjunction, the Miller cycle and low-carbon fuels have an improved effect on both performance and emissions. The optimal results demonstrate that using B60 (60% Biodiesel in the blend) and a −8% Miller effect contributes to a 1.5% improvement in power, 1.2% in BTE, 13.3% in NOx, 38.5% in CO, 8.9% in HC, and 33.0% in soot at a cost of 6.0% increase in BSFC. The results show that it is an easy way to reduce NOx, CO, HC and soot emissions and increase the BTE of the engine by combining Miller cycle and low-carbon fuels.

As one of the most common engine types in nowadays, the thermal efficiency of spark-Ignition (SI) engine is limited due to the lower compression ratio. Various technical solutions have been proposed to suppress knock and improve compression ratio of SI engines. In this paper, an new technical solution based on electromagnetic valve train (EMVT) was proposed to suppress knock of spark ignition engines, so that high compression ratio (HCR) engine (13:5) was obtained. Moreover, experimental and numerical analyses were carried out to optimize the proposed EMVT strategy. The result showed that the proposed EMVT strategies could well suppress the engine knock by reducing end-gas temperature and pressure and improving the spark-flame rate, resulting in significantly enhanced power, economic, and emission characteristics of SI engines. This study provides theoretical basis and technical approach for the development of internal combustion engines with high efficiency and high compression ratio. [ABSTRACT FROM AUTHOR]

Miller cycle has been shown as a promising engine strategy to reduce in-cylinder nitrogen oxide (NOx) formation during the combustion process and facilitate its removal in the aftertreatment systems by increasing the exhaust gas temperature. However, the level of NOx reduction and the increase in exhaust gas temperature achieved by Miller cycle alone is limited. Therefore, research was carried out to investigate the combined use of Miller cycle with other advanced combustion control strategies in order to minimise the NOx emissions and the total cost of ownership. In this article, the effects of Miller cycle, exhaust gas recirculation, and post-injection were studied and analysed on the performance and exhaust emissions of a single cylinder heavy-duty diesel engine. A cost–benefit analysis was carried out using the corrected total fluid efficiency, which includes the estimated urea solution consumption in the NOx aftertreatment system as well as the fuel consumption. The experiments were performed at a low load of 6 bar net indicated mean effective pressure. The results showed that the application of a Miller cycle–only strategy with a retarded intake valve closing at −95 crank angle degree after top dead centre decreased NOx emissions by 21% to 6.0 g/kW h and increased exhaust gas temperature by 30% to 633 K when compared to the baseline engine operation. This was attributed to a reduction in compressed gas temperature by the lower effective compression ratio and the in-cylinder mass trapped due to the retarded intake valve closing. These improvements, however, were accompanied by a fuel-efficiency penalty of 1%. A further reduction in the level of NOx from 6.0 to 3.0 g/kW h was achieved through the addition of exhaust gas recirculation, but soot emissions were more than doubled to 0.022 g/kW h. The introduction of a post-injection was found to counteract this effect, resulting in simultaneous low NOx and soot emissions of 2.5 and 0.012 g/kW h, respectively. When taking into account the urea consumption, the combined use of Miller cycle, exhaust gas recirculation, and post-injection combustion control strategies were found to have relatively higher corrected total fluid efficiency than the baseline case. Thus, the combined 'Miller cycle + exhaust gas recirculation + post-injection' strategy was the most effective means of achieving simultaneous low exhaust emissions, high exhaust gas temperature, and increased corrected total fluid efficiency. [ABSTRACT FROM AUTHOR]

High nitrogen oxide levels of the conventional diesel engine combustion often requires the introduction of exhaust gas recirculation at high engine loads. This can adversely affect the smoke emissions and fuel conversion efficiency associated with a reduction of the in-cylinder air-fuel ratio (lambda). In addition, low exhaust gas temperatures at low engine loads reduce the effectiveness of aftertreatment systems necessary to meet stringent emissions regulations. These are some of the main issues encountered by current heady-duty diesel engines. In this work, variable valve actuation-based advanced combustion control strategies have been researched as means of improving upon the engine exhaust temperature, emissions, and efficiency. Experimental analysis was carried out on a single-cylinder heady-duty diesel engine equipped with a high-pressure common-rail fuel injection system, a high-pressure loop cooled exhaust gas recirculation, and a variable valve actuation system. The variable valve actuation system enables a late intake valve closing and a second intake valve opening during the exhaust stroke. The results showed that Miller cycle was an effective technology for exhaust temperature management of low engine load operations, increasing the exhaust gas temperature by 40°C and 75°C when running engine at 2.2 and 6 bar net indicated mean effective pressure, respectively. However, Miller cycle adversely effected carbon monoxide and unburned hydrocarbon emissions at a light load of 2.2 bar indicated mean effective pressure. This could be overcome when combining Miller cycle with a second intake valve opening strategy due to the formation of a relatively hotter in-cylinder charge induced by the presence of internal exhaust gas recirculation. This strategy also led to a significant reduction in soot emissions by 82% when compared with the baseline engine operation. Alternatively, the use of external exhaust gas recirculation and post injection on a Miller cycle operation decreased high nitrogen oxide emissions by 67% at a part load of 6 bar indicated mean effective pressure. This contributed to a reduction of 2.2% in the total fluid consumption, which takes into account the urea consumption in aftertreatment system. At a high engine load of 17 bar indicated mean effective pressure, a highly boosted Miller cycle strategy with exhaust gas recirculation increased the fuel conversion efficiency by 1.5% while reducing the total fluid consumption by 5.4%. The overall results demonstrated that advanced variable valve actuation-based combustion control strategies can control the exhaust gas temperature and engine-out emissions at low engine loads as well as improve upon the fuel conversion efficiency and total fluid consumption at high engine loads, potentially reducing the engine operational costs. [ABSTRACT FROM AUTHOR]

It is important to understand the lean-burn combustion process of large-bore natural gas engines and influences on it in order to improve next generations of gas engines to meet the increasing requirements for high efficiencies and low emissions. The investigations in this study focus on the ignition and early flame propagation phase using optical experiments on a single-cylinder research engine, since both phases highly influence the subsequent main-combustion. Scavenged prechambers with different operating conditions and a tangential and radial nozzle alignment as well as unscavenged prechamber and direct spark plug ignition are compared. Beside the phenomenology of the ignition system itself, the interaction of the main-chamber charge motion and the ignition system is important to understand. Therefore, different valve timings (conventional timings and Miller cycle) as well as a low and high turbulence setup are subject of the study. Numerical simulations of the cold flow are used to understand the charge motion and mixture formation in the prechamber as well as in the main-chamber. The experiments depict an enhancement of the first flame propagation phase using a scavenged prechamber due to hot turbulent jets emerging from the nozzles. Furthermore, an influence of the nozzle geometry and the boundary conditions on the jet development and on the early flame propagation is observed. It is seen by the optical measurements that cycle-to-cycle variations can originate from the hot turbulent jets and its influence on the ignition of the main-chamber charge. Further, the optical measurements show that a low in-cylinder swirl and turbulence due to Miller cycle has an impact on the interaction between the in-cylinder charge motion and the jets. A comparison between high turbulence and low turbulence in-cylinder flows on the combustion is carried out. It is shown that the scavenged prechamber can compensate the lack of turbulence in the main-chamber. Hence, the scavenged prechamber enhances the flame propagation due to induced turbulence in the main-chamber and larger flame front surfaces generated by penetrating flame torches. [ABSTRACT FROM AUTHOR]

Compared to the standard cycle, the Miller cycle decreases the cylinder maximum combustion temperature which can effectively reduce NOx emissions. In this paper, a 0-D two-zone combustion model is used to establish the simulation model of a marine dual-fuel engine, which is calibrated according to the test report under different loads. Due to the high emissions under part load, the Miller cycle (early intake valve closing method) is used for optimization. By analyzing the cylinder pressure, temperature, heat release rate, and NOx emissions under different cases, it can be found that the effective working volume and thermal efficiency decrease with the advance of intake valve closing and improve with the increase of the geometric compression ratio. In all optimization cases, the NOx emissions and fuel consumption are reduced by 72% and 0.1%, respectively, by increasing the geometric compression ratio to 14 and the intake valve closing timing to 510 °CA (the reference top dead center is 360 °CA). The simulation results show that the early intake valve closing Miller cycle can effectively reduce the NOx emissions and cylinder peak pressure. [ABSTRACT FROM AUTHOR]

Internal combustion engines (ICEs) have harmful effects on the environment in terms of emissions. According to present emission regulations, reducing NOX emissions came into prominence. One of the techniques of reducing NOX emissions is implementation of Miller Cycle to the engine. A comparative performance analysis and optimization based on the non-dimensional power output and thermal efficiency criteria have been performed for an irreversible Dual-Miller Cycle. The effect of the design parameters such as cycle compression ratio, cut-off ratio and Miller cycle ratio of the cycle have also been investigated on the basis of having the internal irreversibility with assuming the working fluid is an ideal gas with constant specific heat. Performance analysis has been also extended to the Otto-Miller and Diesel-Miller cycles which may be considered as two special cases of the Dual-Miller cycle. The analysis and optimization study carried out in this work are hoped to provide guidelines for optimal design in terms of power output and thermal efficiency for internal combustion engines. [ABSTRACT FROM AUTHOR]

To achieve low-carbon transportation, a novel Miller cycle was implemented by using asynchronous late intake valve closing (ALIVC) in the high compression ratio turbocharged SI engine. The effects of the Miller cycle on combustion and performance were investigated and compared with the original Otto cycle. Based on this, EGR was introduced and its effects on Miller cycle engine performance and energy balance were investigated. The results show that the Miller-CR12.5 can reduce pumping loss and suppress knock without sacrificing power output. Compared to the Otto-CR10.5, the Miller-CR12.5 achieves a 6.7 % reduction in BSFC at the lowest fuel consumption point and a 10–11.4 % reduction at high loads. The lower peak combustion temperature allows the Miller-CR12.5 to eliminate fuel-enriched injection at high loads, reducing the heat transfer and combustion loss. The introduction of EGR in the ALIVC Miller cycle engine decreases the peak HRR and extends the combustion duration. However, the advanced 50 % combustion position and increased effective expansion ratio can improve engine performance. At 10 % EGR rate, the BSFC obtains a 2.1 % reduction and NOx emissions are reduced by 62 %. As the EGR rate increases, the heat transfer and exhaust loss decrease, but there is a slight increase in combustion loss. • A novel Miller cycle was achieved by using asynchronous late intake valve closing. • ALIVC Miller cycle significantly improves engine performance. • ALIVC Miller cycle can fully eliminate fuel-enrichment injection at high loads. • Optimized BSFC and NOx emissions through Miller cycle combined with EGR. [ABSTRACT FROM AUTHOR]

The current article presents a method to reconstruct the mean velocity field of a cyclic flow for an input parameter value that has not been measured, allowing for the number of tests to be reduced. It is applied to the tumble flow of a gasoline engine following a Miller cycle. New engines often include variable valve timing (VVT) systems to maximize the efficiency of such over-expanded cycles for different operating points. The reconstruction was thus carried out using different offset values of the intake valve lift timing. Experimental data were collected from a transparent engine in an early intake valve closing (EIVC) configuration using particle image velocimetry (PIV). The mean velocity field reconstruction was based on the interpolation of the proper orthogonal decomposition (POD) coefficients. The accuracy of the method was evaluated at different points by comparing the interpolated and the measured flow fields. The accuracy was estimated by calculating the error in the rotation rate of the tumble and the position of its center of rotation. The new mean velocity field set allowed for the position of the tumble’s center of rotation to be closely tracked according to the input parameter and a rotation rate map to be made. Some results on Miller’s cycle could thus be found and the data generated could guide future developments.

This paper focuses on the investigation and optimisation of the Miller cycle, methanol, ethanol and turbocharging when applied to a high-performance gasoline engine. These technologies have been applied both individually and concurrently to test for potential compounding effects. Improvements have been targeted with regards to both emission output and performance. Also assessed is the capability of the engine to operate when exclusively powered by biofuels. This has been carried out numerically using the 1D gas dynamics tool ‘WAVE’, a 1D Navier–Stokes equation solver. These technologies have been implemented within the McLaren M838T 3.8L twin-turbo engine. The Miller cycle early intake valve close (EIVC) improved peak efficiency by 0.17% and increased power output at low and medium loads by 11%. Reductions of 6% for both NOx and CO were also found at rated speed. The biofuels achieved NOx and CO reductions of 60% and 96% respectively, alongside an efficiency increase of 2.5%. Exclusive biofuel use was found to be feasible with a minimum 35% power penalty. Applied cooperatively, the Miller cycle and biofuels were not detrimental to each other, compounding effects of a further 0.05% efficiency and 2% NOx improvements were achieved.

In theory, high compression ratio has the potential to improve the thermal efficiency and promote the power output of the SI engine. However, the application of high compression ratio is substantially limited by the knock in practical working process. The objective of this work is to comprehensively investigate the application of high compression ratio on a gasoline engine based on the Miller cycle with boost pressure and split injection. In this work, the specific optimum strategies for CR10 and CR12 were experimentally investigated respectively on a single cylinder DISI engine. It was found that a high level of Miller cycle with a higher boost pressure could be used in CR12 to achieve an effective compression ratio similar to CR10, which could eliminate the knock limits at a high compression ratio and high load. To verify the advantages of the high compression ratio, the fuel economy and power performance of CR10 and CR12 were compared at full and partial loads. The result revealed that, compared with CR10, a similar power performance and a reduced fuel consumption of CR12 at full load could be achieved by using the strong Miller cycle and split injection. At partial load, the conditions of CR12 had very superior fuel economy and power performance compared to those of CR10. [ABSTRACT FROM AUTHOR]

Summary: The Miller cycle applications have been performed to diminish NOx released from internal combustion engines (ICEs), in recent years. The Miller cycle provides decreased compression ratio and enhanced expansion ratio; hereby, maximum in‐cylinder combustion temperatures diminish, and NOx formations slow down remarkably. Another less‐known method is Takemura cycle application, which provides heat addition into engine cylinder at constant combustion temperatures. In this study, a novel cycle including the Miller cycle and the Takemura cycle has been developed by using novel numerical models and computing methods with seven processes and a novel way to decrease NOx emissions at higher levels compared with the single applications of known cycles. A comprehensive performance examination of the proposed cycle engine in terms of performance characteristics such as effective power (EFP), effective power density (EFPD), exergy destruction (X), exergy efficiency (ε), and ecological coefficient of performance (ECOP) has been conducted. The impacts of engine operating and design parameters on the performance characteristics have been computationally examined. Furthermore, irreversibilities depending on incomplete combustion loss (INCL), exhaust output loss (EXOL), heat transfer loss (HTRL), and friction loss (FRL) have been considered in the performance simulations. The minimum exergy destruction and maximum performance specifications have been observed with 30 of the compression ratio. Maximum effective power values have been obtained at range between 1 and 1.2 of equivalence ratio. The optimum range for exergy efficiency is between 0.8 and 1 of equivalence ratio. Increasing engine speed has provided enhancing effective power. However, an optimum range has been found for the exergy efficiency that is interval of 3000 to 4000 rpm. The results obtained can be assessed by researchers studying on modeling of the engine systems and designs. [ABSTRACT FROM AUTHOR]