Search

Abstract. The rapid increase in energy demand in the city of Reykjavik has posed the need for an additional supply of hot water from deep geothermal energy. The deep hydraulic (re-)stimulation of well RV-43 on the peninsula of Geldinganes (north of Reykjavik) is an essential component of the plan implemented by Reykjavik Energy to meet this energy target. Hydraulic stimulation is often associated with fluid-induced seismicity, most of which is not felt on the surface, but which, in rare cases, can cause nuisance to the population and even damage to the nearby building stock. This study presents a first of its kind pre-drilling probabilistic induced-seismic hazard and risk analysis for the site of interest. Specifically, we provide probabilistic estimates of peak ground acceleration, European microseismicity intensity, probability of light damage (damage risk), and individual risk. The results of the risk assessment indicate that the individual risk within a radius of 2 km around the injection point is below 0.1 micromorts, and damage risk is below 10−2, for the total duration of the project. However, these results are affected by several orders of magnitude of variability due to the deep uncertainties present at all levels of the analysis, indicating a critical need in updating this a-priory risk assessment with in-situ data collected during the stimulation.

Low injectivity is often experienced in geothermal doublets installed in sandstone reservoirs. This even led to a shutdown of the Mezőberény (Hungary) geothermal site. An on-site campaign was carried out in January 2021 to prepare a stimulation aiming to enhance the transmissivity of the sedimentary reservoir and the near-wellbore zone of this site. Previous studies have concluded that insufficient injectivity may be linked to a high skin effect in the near well-bore zone and pore clogging in combination with the low net sandstone content of the fluvio-deltaic reservoir. A chemical soft stimulation based on the injection of hydrochloric acid (HCl) was successfully used to unclog and recover the well injectivity. Despite such empirical evidence, the geochemical mechanisms leading to both, detrimental formation of clogging and the HCl-driven transmissivity restoration, have not yet been elucidated. This work presents the results of a novel analysis aiming at (a) predicting the dominant type of clogging forming in the near-well bore zone; (b) quantifying the drop in hydraulic conductivity as clogging occurs; and (c) supporting the optimization of the HCl dosage during the chemical soft stimulation. The study is supported by new experimental datasets never presented before from the Mezőberény site and a geochemical model set-up simulating the main mechanisms involved in the clogging and unclogging processes. It is concluded that the biofilm formation was the dominant, while the precipitation of calcite and amorphous ferrihydrite—later reduced to magnetite by microbes—was the secondary clogging mechanism: In the long-term (yearly scale) simulating the hydraulic conductivity showed a decline with forming scales; therefore, biofilm was presumably responsible for the experienced rapid (1 month) clogging. When modelling the chemical stimulation, the estimated amount of precipitated minerals was dissolved already with 2.5 mol of HCl per liter of water (~ 10 m/m%). Therefore, the 20 m/m% of HCl chosen during the field campaign might had a beneficial effect dissolving the potentially higher amount of scaling and/or the carbonate minerals of the matrix near the wellbore. Overall, it is concluded that the chemical and the microbial analyses together with the geochemical model were critical to tailor the remediation attempts and to propose further development or reconstruction of the surface system before going into operation to prevent recurrent impairments. Our findings highlight the importance of interactions of various clogging mechanisms with each other as well as with the reservoir processes and provide approaches to tackle the issue of injectivity drop by characterizing and quantifying their effects. [ABSTRACT FROM AUTHOR]

This article discusses the phenomenon of induced seismicity, which refers to the human-caused generation of tremors and seismic events that alter the state of subsurface stresses. The occurrence of induced seismicity during subsurface technologies, such as shale gas development and renewable energy extraction, can lead to project delays and concerns about safety and environmental impact. The article highlights the need to understand the mechanisms of induced seismicity and develop strategies to minimize its effects. It presents a collection of research papers that explore fluid-induced seismicity in various energy production and storage technologies, offering insights into the interplay between fluid injection, fault behavior, and subsurface structures. The findings contribute to evidence-based policymaking and regulatory processes, supporting the development of sustainable subsurface operations for renewable energy and decarbonization technologies. [Extracted from the article]

Enhanced geothermal systems (EGSs) developed by hydraulic stimulation are promising for exploiting petrothermal heat by improving fluid pathways in low-permeable geothermal reservoir rocks. However, fluid injection into the subsurface can potentially cause large seismic events by reactivating pre-existing faults, which is a significant barrier to EGSs. The management of injection-induced seismicity is, therefore, essential for the success of EGSs. During the hydraulic stimulation of an EGS, fluid can be injected into a fault zone or into the rock matrix containing pre-existing faults adjacent to the injection well. The differences in hydromechanical responses between fluid injection into and adjacent to a fault have not been investigated in detail. Here, we performed triaxial fluid injection experiments involving injecting fluid directly and indirectly into a fault in granite rock samples to analyse the distinct hydromechanical responses and estimate the injection-induced seismicity in both cases. Our results suggest that in addition to directly injecting fluid into a critically stressed fault, injecting into nearly intact granite adjacent to the fault could also cause injection-induced seismic hazards owing to the high fluid pressure required to create new fractures in the granite matrix. It is, therefore, important to carefully identify pre-existing faults within tight reservoirs to avoid injecting fluid adjacent to them. Additionally, once prior unknown faults are delineated during hydraulic stimulation, appropriate shut-in strategies should be implemented immediately to mitigate seismic risks. This article is part of the theme issue 'Induced seismicity in coupled subsurface systems'. [ABSTRACT FROM AUTHOR]

In this article, a high-resolution acoustic emission sensor, accelerometer, and broadband seismometer array data set is made available and described in detail from in situ experiments performed at Äspö Hard Rock Laboratory in May and June 2015. The main goal of the hydraulic stimulation tests in a horizontal borehole at 410 m depth in naturally fractured granitic rock mass is to demonstrate the technical feasibility of generating multi-stage heat exchangers in a controlled way superiorly to former massive stimulations applied in enhanced geothermal projects. A set of six, sub-parallel hydraulic fractures is propagated from an injection borehole drilled parallel to minimum horizontal in situ stress and is monitored by an extensive complementary sensor array implemented in three inclined monitoring boreholes and the nearby tunnel system. Three different fluid injection protocols are tested: constant water injection, progressive cyclic injection, and cyclic injection with a hydraulic hammer operating at 5 Hz frequency to stimulate a crystalline rock volume of size 30 m × 30 m × 30 m at depth. We collected geological data from core and borehole logs, fracture inspection data from an impression packer, and acoustic emission hypocenter tracking and tilt data, as well as quantified the permeability enhancement process. The data and interpretation provided through this publication are important steps in both upscaling laboratory tests and downscaling field tests in granitic rock in the framework of enhanced geothermal system research. Data described in this paper can be accessed at GFZ Data Services under 10.5880/GFZ.2.6.2023.004. [ABSTRACT FROM AUTHOR]

Samples of flowback water from a 4.3 km deep geothermal borehole in granite (Pohang, South Korea) were collected following a period of hydraulic stimulation by injection of surface water. Electrical conductivity, temperature and water chemistry of the flowback water were measured. To a first approximation, the data conform closely to a simple ‘mixing tank’ model, with an exponential trend between two end members: an initial injected surface water to a more brackish ‘resident groundwater’ composition. Significant deviation from the ‘mixing tank’ trend would be an indication of significant recent water-rock interaction or other anomalous factors. Such a deviation can tentatively be seen in Na+/Cl- data, especially between 88 and 200 m3 flowback (2.8 to 8.8 hr).

Fault zones often serve as the major fluid pathways in a variety of geo-energy systems, such as deep geothermal systems. However, injection-induced instability of faults can sometimes lead to large-magnitude earthquakes. Cyclic injection has thus been proposed as an alternative injection protocol to better manage and mitigate the associated seismic risks. The risks of injection-induced seismicity depend primarily on the extent and magnitude of the fluid pressure perturbation. When fluid is injected into a fault zone, the local fault permeability will be enhanced, which in turn promotes the migration of fluid along the fault. This nonlinear process is further complicated during cyclic injection via alternating the injection pressure. In this study, both numerical and analytical modelling are conducted to investigate cyclic fluid injection into a fault zone with pressure sensitive permeability, in which the local fault permeability changes as a function of the local effective stress. The match with laboratory-scale experimental and field-scale analytical results of cyclic fluid injection verifies the accuracy of the numerical model. The parametric study reveals that the injection pressure attenuation, quantified by the amplitude ratio and phase shift, is enhanced by a lower initial fault permeability, a smaller stress sensitivity coefficient and a shorter period of pressure cycle (i.e. a higher frequency). Besides, the amplitude of the pressure cycle has a negligible effect on the injection pressure attenuation. We also discuss the implications of our results for the less amenable far-field seismic hazard and post shut-in seismicity. [ABSTRACT FROM AUTHOR]