Search

The generation of abrasive particles is an unavoidable consequence of sliding electrical contact wear in conductive slip rings (SRs). The adhesion of abrasive particles to the insulators may lead to a decrease in flashover voltage, posing a risk to satellite power transmission. In this paper, the effect of abrasive particles on flashover is first studied. Surface abrasive particles can distort the surface electric field of the dielectric, absorb scattered electrons, and then re-emit them, thereby accelerating the development and formation of secondary electron avalanches. Flashover test results indicate that surface abrasive particles lead to a significant reduction in flashover voltage. To mitigate the impact of particle adhesion on flashover, a method of constructing particle traps on the surface of insulators is proposed. The location and structural parameters of the particle trap are further optimized and determined. The flashover test results using planar dielectric samples and SR insulator samples both demonstrate that the optimized particle trap can significantly improve the flashover voltage. The dielectric maintains high electrical strength even when particles are trapped in particle traps. The physical details of the impact of particles on flashover and the effect of particle traps are analyzed utilizing an electron movement simulation, corroborating the experiment from a microscopic aspect. [ABSTRACT FROM AUTHOR]

Cellulose insulating paper is widely used in the power industry for its good electrical insulating properties. Moisture sharply increases its conductivity, which directly leads to the weakening of insulation performance and greatly increases the risk of subsequent electric field distortion and insulation breakdown. This paper focuses on the microscopic mechanism of moisture changing the characteristics of charge transport in cellulose insulation and attempts to reveal the related conductivity mechanism. To achieve this purpose, microscopic and macroscopic perspectives are integrated and several simulation and experimental methods are utilized comprehensively. The molecular dynamics simulation results showed that most water molecules in damped cellulose were individually and uniformly adsorbed on the hydroxyl groups by hydrogen bond, and the quantum chemistry computation results showed that the lowest unoccupied molecular orbital more appeared on the water molecule and the corresponding density of state increased. Then, experimentally, it was confirmed that the trap energy level decreased by the thermally stimulated current method. On this basis, the promotion effect of moisture on charge transport is predicted and verified by polarization and depolarization current methods. As the moisture content increased, more charge carriers escaped from the trap by hopping and participated in long-range continuous charge motion. Therefore, after dampness, the current of cellulose insulating paper increased exponentially with the increase in electric field strength, which was consistent with the hopping conductivity mechanism. [ABSTRACT FROM AUTHOR]

Moisture ingress is one of the major causes of aging in oil–paper insulated transformers; the measurement of the moisture content of the insulating material is thus necessary during transformer disassembly for maintenance. One critical engineering consideration is the need for rapid and nondestructive moisture content measurement of the oil–paper insulation to minimize the power-outage time. Herein, a rapid characterization method for the moisture content of oil–paper insulation based on the dielectric response obtained using a microstrip petal-like ring resonator (MPRR) is proposed. The geometric parameters of the resonator and dielectric response model were established based on simulations and theoretical analysis. The geometry of the resonant ring was optimized by modifying the originally circular ring structure of the microstrip ring resonator (MRR) into a petal-like ring structure; this increases the number of resonant peaks from five to seven in the frequency range of 0.5–6.0 GHz for the same electrode area. The effects of the coupling mode, coupling gap, and microstrip ring size on the resonance characteristics of the MPRR were simulated and analyzed. Compared with the MRR, the MPRR has the advantages of a reduced fundamental resonant frequency and a smaller resonant-ring area that improves radiation efficiency. The impact of moisture content on the dielectric response of the pressboard obtained using the MPRR was studied. A moisture-calculation equation based on the measured dielectric response for a selected type of pressboard was established by the Lasso regression. The results of verification experiments show that the error of the proposed method is sufficient for practical applications. [ABSTRACT FROM AUTHOR]

Frequency Domain Spectroscopy (FDS) is widely used to estimate oil–paper insulation. The high moisture and long aging change the FDS characteristics of the insulating oil–paper, so normalization processing is required. Still, the choice of single activation energy needs further research. This paper studies the FDS characteristic of oil–paper insulation samples with different moisture and aging degrees and improves the traditional temperature correction method. The enhanced Arrhenius model uses the segmented activation energy to make the normalized FDS curve coincide better with the target curve, and the error is reduced. In addition, to verify the method's effectiveness, this paper proposes an iterative correction process. It corrects the tan δ-f curve of the bushing with an aging time of 800 h based on segmented activation energy, and the overall normalization effect is improved. [ABSTRACT FROM AUTHOR]

With the development of high-density and highly integrated electronic devices, the insulation characteristics between the interconnects of printed circuit boards (PCBs) are the key issues to be considered in their design and production. Most of the existing studies on insulation characteristics are based on parallel interconnect structures; however, the possibility of flashover or breakdown on PCB at parallel interconnects is relatively low compared to other irregular structures. The flashover characteristics of PCB interconnects need to be more comprehensively presented. In this paper, the commonly used interconnects were divided into three typical structures. Under the same DC excitation, the "interconnect with pad" structure had the most severe electric field concentration, and the insulation characteristic of this structure was the worse of the three. Furthermore, the effects of the distance between the interconnect and pad size on the flashover voltages of the "interconnect with pad" structure were investigated and explained by the maximum electric field strength, which could be approximately calculated by the existing equation. [ABSTRACT FROM AUTHOR]