Search

Powder metallurgy (PM) Ti–6Al–2Sn–4Zr–2Mo–0.1Si–(0, 2, 4)W (wt%) alloys were fabricated by thermomechanical consolidation of TiH 2 -based powder compacts and subsequent heat treatments. Samples of the as-fabricated alloys were also heated at 650 °C for 200 h. The addition of 2 or 4 wt%W to the base alloy changed its microstructure of parallel α/β lamellar colonies and grain boundary α (α GB) to an interwoven α/β t microstructure consisting of α GB and a network of interpenetrating α plates with β transformed structure (β t) domains comprising variants of fine α laths and β matrix. The partition of the β stabilizing W between β and α phases and the low diffusivity of W atoms limited the growth of α plates/laths, decreasing the thickness of α plates/laths and increasing the volume fraction of β. The increased hardening of the β phase and enhanced α/β interface strengthening associated with the 4 wt%W addition led to a significant increase in the tensile strength of the alloy from 1281 ± 10–1411 ± 12 MPa. However, the high flow stress and the very fine microstructure caused significant strain localization in the weak α GB , resulting in premature fracture of the α GB (intergranular fracture) and the low ductility (1.4%). Here, premature fracture meant the fracture occurred prior to the alloy reaching its ultimate tensile strength. The heating caused the β interlaths in the W-free alloy to partially dissolve and become β particles distributed along the original lines of β interlaths accompanied by the precipitation of α 2 -Ti 3 Al in the α plates. The addition of W inhibited the dissolution of β interlaths and caused the precipitation of a higher volume fraction of α 2 precipitates during heating. The microstructural changes caused by heating resulted in a slight decrease in strength and a significant decrease in ductility for the W-free alloy, but a significant increase of the yield strength of the 2 W and 4 W alloys with some sacrifice of the tensile ductility. The microstructural reasons for the effects on mechanical properties were analyzed with the assistance of detailed characterization of the dislocations in the deformed specimens. • Effects of W alloying on a PM Ti–6Al–2Sn–4Zr–2Mo–0.1Si alloy are investigated. • W refines α plates and enhances formation of β transformed structure domains. • W enhances hardening of the β phase and α/β interface strengthening. • W increases the microstructural stability and prevents the strength reduction from heating. • High W content promotes α 2 precipitation strengthening of the alloy after heating. [ABSTRACT FROM AUTHOR]

• With an addition of 0.2 wt%Si, the Si atoms are equally in α and β phases. • Si solute atoms retard the growth of α phase, causing refinement of the α/β t lamellar structure. • Si atoms enhance solid solution strengthening and Si atoms enhanced α/β t interface strengthening. • Increasing the Si content to 0.5 wt% cause a further increase of the yield strength by 50 MPa. • With a high strength, the tensile ductility deteriorates, due to the premature fracture of grain boundary α layers. Ti-4Al-4Mo-4Sn-xSi (wt%) (x = 0, 0.2, 0.5) alloys were fabricated by hot extrusion of compacts of blends of TiH 2 , AlMo60 master alloy and other required elemental powders followed by heat treatments involving vacuum annealing, solution treatment, air cooling and aging. The microstructure of the alloys consists of α plates, lamellae of α and transformed β structure (β t), β t blocks as well as grain boundary α layers. With the addition of 0.2 wt%Si, the Si atoms exist in equal concentration in both α and β t regions as solute atoms, and they retard the growth of α phase, causing a decrease of the average thickness of α plates and lamellae and slight increase of the volume fraction of β t lamellae and blocks. The solid solution strengthening and enhanced α/β interface hardening brought by the 0.2 wt%Si cause the yield strength of the Ti-4Al-4Mo-4Sn alloy to increase significantly from 1030 to 1130 MPa with a slight decrease of the tensile ductility (7.4% vs 6.8%) and without changing the fracture behavior. With the addition of 0.5 wt%Si, the extra Si causes nanometer sized silicide (Ti 5 Si 3) precipitates to form in both α and β t regions and further microstructural refinement. The additional α/β interface hardening and precipitation hardening cause the yield strength of the alloy to increase further to 1177 MPa, but the tensile ductility deteriorates clearly with the elongation to fracture decreasing to 4.9%. The main reason for this ductility decrease is the premature fracture of grain boundary α layers caused by the higher flow stress which can induce more strain localization at the grain boundary α layers. [ABSTRACT FROM AUTHOR]