Search

Purpose: This paper aims to present an adaptive method based on finite element analysis to calculate iron losses in switched reluctance motors (SRMs). Calculation of iron losses by analytical formulas has limited accuracy. On the other hand, its estimation in rotating electrical machines through fully dynamic simulations with a fine time-step is time-consuming. However, in the initial design process, a quick and sufficiently accurate method, i.e. a value close to that of iron losses, is always welcome. The method presented in this paper is a semi-analytical approach. The main problem is that iron losses depend on d B/d t. Therefore, the accuracy of the calculation of iron losses depends on the accuracy of the calculation of the first derivative of the flux density waveform. When adopting a magnetostatic model to estimate the iron losses, an important question arises: by how many magnetostatic simulations can the iron losses be estimated within the desired accuracy? In the proposed algorithm, the aim is not to accurately calculate the value of iron losses in SRMs. The objective is to find a numerical error criterion to calculate iron losses in SRMs with a minimum number of magnetostatic simulations. Design/methodology/approach: A finite element solver is developed by authors in MATLAB to solve the 2 D nonlinear magnetostatic problem using the Newton–Raphson method. A parametric program is developed to create geometry and mesh. The proposed method is implemented in MATLAB using the developed solver. Counterpart simulations are done in the ANSYS Maxwell software to validate the accuracy of the results generated by the developed solver. Findings: The performance of the proposed method is studied on a 12/8 (500 W) SRM. Three scenarios are studied. The first one is the calculation of iron losses by uniform refinement, and the second one is by adaptive refinement, and the last one is by adaptive refinement started by particular initial points (switching points). According to the results, the proposed method substantially reduces the number of magnetostatic simulations without sacrificing accuracy. Originality/value: The main novelty of this paper is introducing an error criterion to find the minimum number of magnetostatic simulations that are needed to calculate iron losses with the desired accuracy. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this paper is to analyze electromagnetic performance and develop an analytical approach to find the suitable coil combination and no-load flux linkage of the proposed hybrid excited consequent pole flux switching machine (HECPFSM) while minimizing the drive storage and computational time which is the main problem in finite element analysis (FEA) tools. Design/methodology/approach: First, a new HECPFSM based on conventional consequent pole flux switching permanent machine (FSPM) is proposed, and lumped parameter magnetic network model (LPMNM) is developed for the initial analysis like coil combination and no-load flux linkage. In LPMNM, all the parts of one-third machine are modeled which helps in reduction of drive storage, computational complexity and computational time without affecting the accuracy. Second, self and mutual inductance are calculated in the stator, and dq-axis inductance is calculated using park transformation in the rotor of the proposed machine. Furthermore, on-load performance analysis, like average torque, torque density and efficiency, is done by FEA. Findings: The developed LPMNM is validated by FEA via JMAG v. 19.1. The results obtained show good agreement with an accuracy of 96.89%. Practical implications: The proposed HECPFSM is developed for high-speed brushless AC applications like electric vehicle (EV)/hybrid electric vehicle (HEV). Originality/value: The proposed HECPFSM offers better flux regulation capability with enhanced electromagnetic performance as compared to conventional consequent pole FSPM. Moreover, the developed LPMNM reduces drive storage and computational time by modeling one-third of the machine. [ABSTRACT FROM AUTHOR]

Purpose: This paper aims to establish a piecewise Maxwell stress analytical model of bearingless switched reluctance motor (BSRM) for the full rotor angular positions. The proposed model varies from the existing models, which are only applicable to the partial-overlapping positions of stator and rotor poles. By extending the applicable rotor angular positions, this model provides a basic analytical model for the multi-phase excitation control of BSRM. Design/methodology/approach: The full rotor angular positions are classified into the partial-overlapping positions and the non-overlapping positions. At first, two different air gap subdividing methods are proposed, respectively, for the two-position ranges. Then, different integration paths are selected accordingly. Furthermore, two approximate methods are presented to calculate the average flux density of each air gap subdivision. Finally, considering the mutual coupling between the two perpendicular radial suspension forces, a piecewise Maxwell stress analytical model is derived for the full rotor angular positions of BSRM. Findings: A piecewise Maxwell stress analytical model of BSRM is built for the full rotor angular positions, and applicable to the multi-phase excitation mode of BSRM. For the partial-overlapping positions and the non-overlapping positions, two sets of air gap subdividing methods, integration paths and approximate calculation methods of air gap flux densities are proposed, respectively. The accuracy and reliability of the proposed model are verified by the finite element method. Originality/value: The piecewise Maxwell stress analytical model of BSRM for the full rotor angular positions is proposed for the first time. The novel air gap subdividing methods, integration paths, approximate calculation methods of air gap flux densities and the coupling between the two radial suspension forces are adopted to improve the modeling accuracy. As the applicable range of rotor angular position is extended, this model overcomes the limitation of the existing models only for single-phase excitation mode and contributes to the accurate control of BSRM multi-phase excitation mode. [ABSTRACT FROM AUTHOR]

Purpose: The aim of this paper is to propose the model for analyzing the electromagnetic performances of permanent magnet vernier machines (PMVMs) under healthy and faulty conditions. Design/methodology/approach: The model uses interconnected reluctance network formed based on the geometrical approximations to predict magnetic performances of the machine. The network consists of several types of reluctances for modeling different parts of machine. Applying Kirchhoffs laws in the network and the machine windings, magnetic and electrical equations are obtained, respectively. To construct the model system of equations, the electrical equation is converted into algebraic form by using the trapezoidal technique. Moreover, the system of equations must be solved by Newton–Raphson method in each step-time because of considering the core saturation effect. Findings: The proposed model is developed based on the modified magnetic equivalent circuit (MEC) method, in which the number of flux paths in different parts of the machine can be arbitrary selected. The saturation effect, skewed slots, the desired machine geometrical parameters and various winding arrangements are included in the proposed model; therefore, it can evaluate the time and space harmonics in modeling the PMVMs. Furthermore, a pattern for inter-turn fault detection is extracted from the stator current spectrum. Finally, 2 D-finite element method (FEM) and 3 D-FEM analysis are carried out to evaluate and verify the results of the proposed MEC model. Originality/value: Generally, the element numbers have important role in modeling the machine and calculating its performance. Hence, the proposed MEC model's capability to choose desired number of flux paths is advantage of this paper. Moreover, the developed MEC can be used for analyzing several electrical machines, including other types of vernier machines, with simple modification. [ABSTRACT FROM AUTHOR]

Purpose: High torque ripple is the significant challenge of the synchronous reluctance machine in household electric appliances, electric vehicles and so on. This paper aims to present an optimized design of a synchronous reluctance rotor structure to reduce the torque ripple with improving the average torque by the particle swarm optimization (PSO) algorithm. Design/methodology/approach: The optimization of rotor geometries has been investigated. Most of the rotor parameters such as the width of iron parts, the width of barriers along d and q axes and the endpoint angle of barriers are optimized by a new method using the PSO algorithm. After optimization, the resulted optimum design along with the initial design is simulated by two-dimensional finite element method and results are compared. At the end, a prototype is constructed and tested. Results of the experiment are compared with the simulation results where acceptable adoption is yielded. Findings: Minimizing the torque ripple without losing the average torque is an important achievement of the synchronous reluctance motor (SynRM) optimization; furthermore, the finite element analysis and experimental results indicate that the torque ripple of the SynRM with the optimized rotor is reduced significantly. Also, increasing the number of optimization parameters can effectively obtain an accurate shape of the SynRM barrier. Originality/value: Because of the high number of parameters in synchronous reluctance rotors, the majority of proposed optimizations did not use all geometric parameters of the rotor and tried to simplify the optimization by ignoring several optimization parameters or reducing the number of flux barriers. In this optimization, most of the rotor parameters have been used to achieve the precise barrier shape with the aim of reducing the torque ripple in SynRM. [ABSTRACT FROM AUTHOR]