Search

This study examined the possibility of using various types of waste paper—used newsprint (NP), used lightweight coated paper (LWC), used office paper (OP), and used corrugated cardboard (CC)—for the removal of anionic dyes, Acid Red 18 (AR18) and Acid Yellow 23 (AY23), and cationic dyes, Basic Violet 10 (BV10) and Basic Red 46 (BR46), from aqueous solutions. The scope of this research included the characterization of sorbents (FTIR, SEM, BET surface area, porosity, pHPZC, effectiveness of water coloration), determination of pH effect on the effectiveness of dye sorption, sorption kinetics (pseudo-first-order model, second-order model, intraparticular diffusion model), and the maximum sorption capacity (Langmuir models and Freundlich model) of the tested sorbents. The use of waste paper materials as sorbents was found to not pose any severe risk of aquatic environment contamination. AR18, AY23, and BV10 sorption intensities were the highest at pH 2, and that of RB46 at pH 6. The waste paper sorbents proved particularly effective in removing cationic dyes, like in the case of, e.g., NP, which had a sorption capacity that reached 38.87 mg/g and 90.82 mg/g towards BV10 and BR46, respectively, and were comparable with that of selected activated carbons (literature data). [ABSTRACT FROM AUTHOR]

The mechanical properties for paper sheets composited with glucose (Glc), methyl cellulose (MC), and carboxymethyl cellulose (CMC) were investigated. The paper composites were prepared by immersing paper sheets in aqueous solutions of these materials and drying at 100 °C for 30 min. The stress–strain curves for these paper composites were measured by a uniaxial tensile apparatus with a stretching speed of 2 mm/min. The breaking stress and strain for untreated paper were 24 MPa and 0.016, respectively. The paper composites demonstrated stress–strain curves similar to the untreated paper; however, the breaking point largely differed for these composites. The breaking strain and breaking stress for the Glc composite slightly decreased and those for the MC composite gradually increased with the concentration of materials composited. Significant increases in the mechanical properties were observed for the CMC composite. The breaking stress, breaking strain, and breaking energy for the 3 wt.% CMC composite were 2.0-, 3.9-, and 8.0-fold higher than those for untreated paper, respectively. SEM photographs indicated that the CMC penetrated into the inner part of the paper. These results strongly suggest that the mechanical improvement for CMC composites can be understood as an enhancement of the bond strength between the paper fibrils by CMC, which acts as a bonding agent. It was also revealed that the breaking strain, breaking stress, and breaking energy for the CMC composites were at maximum at the first cycle and decreased gradually as the immersion cycles increased. [ABSTRACT FROM AUTHOR]

Lead (Pb) pollution from local mines and industrial use increases risks for human, animal, and plant health. Pectin is an effective chelator of Pb, and it has been shown that a unicellular green alga, Penium margaritaceum, synthesizes pectin in the cell wall. In this study, the ability of P. margaritaceum to remove Pb from an aqueous solution was investigated. Energy dispersive X-ray spectroscopy revealed that two strains of P. margaritaceum accumulated Pb on the cell surface. Hence, P. margaritaceum cells were immobilized on cellulose filter paper. The immobilized algal cells were soaked in 1.0 mg/L Pb solution with gentle shaking for 8 h, and Pb in the solution and on the filter paper was measured by flame atomic absorption spectrometry. The immobilized algal cells continuously decreased the Pb concentration to less than 0.5 mg/L and recovered 31.8–32.7% of added Pb. The specific decrease in Pb and increase in Ca were observed in the presence of 1.0 mg/L each of Ca, Mg, Na, and K. Fourier transform infrared spectra suggested that the carboxylic acid group would be responsible for the adsorption of Pb. This study is the first to demonstrate the effectiveness of the immobilized P. margaritaceum cell in removing Pb from aqueous solutions with simple solid–liquid separation. [ABSTRACT FROM AUTHOR]

Paper spray ionization mass spectrometry (PSI MS) has emerged as a notable method for the rapid analysis of biological samples. However, the typical cellulose-based paper tip is incompatible with protein detection due to the strong interaction between cellulose hydroxyl groups and proteins. In this study, we utilized a commercially available polyolefin-based synthetic paper, Teslin®, as an alternative PSI substrate for simple protein analysis. We have named this method "droplet PSI" MS, as the aqueous protein solution droplet retains its shape on the Teslin® paper tip. For droplet PSI, no further chemical pretreatment was necessary for the Teslin® substrate; the only required preparation was shaping the Teslin® paper into a triangular tip. In droplet PSI MS, protein ion signals were instantly detected from a protein solution droplet upon applying a spray solvent in situ along with high voltage (HV). When compared with conventional PSI MS, our method demonstrated superior sensitivity. The droplet PSI MS utilizing Teslin® also showcased flexibility in real-time observation of protein alterations induced by an acid additive. Additionally, the effects of spray solvent composition and the application method were discussed. [ABSTRACT FROM AUTHOR]

This paper presents the development of cheap and selective Paper-based Analytical Devices (PADs) for selective Pd(II) determination from very acidic aqueous solutions. The PADs were obtained by impregnating two cm-side squares of filter paper with an azoic ligand, (2-(tetrazolylazo)-1,8 dihydroxy naphthalene-3,6,-disulphonic acid), termed TazoC. The so-obtained orange TazoC-PADs interact quickly with Pd(II) in aqueous solutions by forming a complex purple-blue-colored already at pH lower than 2. The dye complexes no other metal ions at such an acidic media, making TazoC-PADs highly selective to Pd(II) detection. Besides, at higher pH values, other cations, for example, Cu(II) and Ni(II), can interact with TazoC through the formation of stable and pink-magenta-colored complexes; however, it is possible to quantify Pd(II) in the presence of other cations using a multivariate approach. To this end, UV-vis spectra of the TazoC-PADs after equilibration with the metal ions solutions were registered in the 300–800 nm wavelength range. By applying Partial Least Square regression (PLS), the whole UV-vis spectra of the TazoC-PADs were related to the Pd(II) concentrations both when present alone in solution and also in the presence of Cu(II) and Ni(II). Tailored PLS models obtained with matrix-matched standard solutions correctly predicted Pd(II) concentrations in unknown samples and tap water spiked with the metal cation, making the method promising for quick and economical sensing of Pd(II). [ABSTRACT FROM AUTHOR]

New technological and scientific advances in the development of sensors and actuators demand the development of new devices to deal with recent problems and challenges in these new and emerging processes. Moreover, paper-based devices have tremendous potential for developing actuators as paper exhibits capillary transport and hygroexpansion due to swelling of the fibers when absorbing water. Therefore, this paper proposes a mini actuator that is based on a hygro-thermal-paper-based cantilever beam that is activated by means of a droplet of an aqueous solution in combination with a circulating electrical current to analyze its response. The contribution of this proposal includes the analysis of the flexural response of the mini actuator when it is tested by using two different solutions: distilled water and a water/alcohol solution. Additionally, four cases related to the droplet volume are studied and a statistical analysis of the bending responses is presented. The results achieved show that that water-alcohol solutions have a lower deviation in comparison with water only. Moreover, it is demonstrated that a specific change in the maximum displacement is obtained according to the volume and the type of solution. Thus, it is suggested that the response of the mini actuator can be tuned using different aqueous solutions. [ABSTRACT FROM AUTHOR]

The electrodeposition of copper (Cu), silver (Ag), and their alloys has been a subject of interest since the 19th century. Primarily due to their exceptional features such as good mechanical hardness and electrical conductivity, high resistance to corrosion, and electromigration, Cu–Ag electrodeposits continue to be investigated and developed to improve their properties for different applications. This paper reviews the state of the art in the field of electroplated Cu–Ag alloys in an aqueous solution, with particular emphasis on the observed properties and variety of electrochemical processes used to produce high-quality materials. Moreover, this review paper focuses on the experimental conditions employed for Cu–Ag electrodeposition, intending to understand the basis and manipulate the processes to obtain coatings with superior characteristics and for attractive usage. Finally, the most trending applications of these coatings are discussed depending on different parameters of electrodeposition to provide prospects for potential research. [ABSTRACT FROM AUTHOR]

Ion-adsorption-type rare earth ores (IRE-ores) are a vital source of rare earth elements globally. The percolation properties of the ore body significantly determine the ease of rare earth extraction using in situ leaching processes. This paper investigates the interactions among clay particles in ion-adsorption-type rare earth ores within aqueous solutions, utilizing methods such as mineral particle aggregation and settling and acid–base adsorption on mineral surfaces. Based on these analyses, this paper elucidates the influence of solution properties on the percolation process of ion-type rare earth ores during leaching. The results indicate that the electrostatic attraction between minerals in aqueous solutions is pronounced, enhancing the interaction and resulting in a notable instability of the aggregates. The aggregation of minerals impacts the viscous effect of water bound to the mineral surface on the solution, thereby affecting the percolation rate. Extremely low concentrations of SO42− and CH3COO− can act as surface modifiers, reducing the electrostatic attraction between particles and consequently increasing the leaching percolation rate. [ABSTRACT FROM AUTHOR]

This paper examines the properties of sewage sludge ashes (SSAs) from the incineration of sewage sludge with added limestone for toxic gas treatment. It also evaluates the potential valorization of SSA in cement composites as supplementary cementitious materials (SCMs). The work involves a thorough characterization of four SSAs, including physical, chemical, and mineralogical properties. It also includes assessing the behavior of SSA in water solution through electrical conductivity measurements. The reactivity of ashes was evaluated using the R3 method and mechanical properties. The results revealed that all SSAs present comparable mineralogical and chemical properties, with varying proportions. Major elements such as Ca, Si, Fe, P, and S are predominant in the ashes, with traces of heavy metals. In an aqueous solution, a gradual formation of ettringite was detected only for two SSA. The heavy metal leachability was negligible, confirming that SSA is a non-hazardous waste. Finally, the reactivity and strength activity index assessments revealed a low and slow reactivity of SSA compared to metakaolin or slag. The SSA that favored ettringite formation in aqueous solution presented the lowest compressive strength at 28 days after incorporation in mortar. Despite originating from different incineration sites, these ashes fall under the same category of SCM reactivity. [ABSTRACT FROM AUTHOR]

Hydrophilic and hydrophobic phenomena occur in aqueous solutions. Despite the complex nature of the molecular interactions, the propensity of molecules and ions to hydration is sometimes characterized by a single "hydration number". Passynski's method for determining the hydration numbers in dilute aqueous solutions belongs to the group of methods based on the analysis of the isentropic compressibility of a mixture. Isentropic compressibility is a thermodynamic material constant; thus, the paper deals with Passynski's approach discussed in terms of thermodynamics. First, Passynski's assumptions were applied to the volume of the mixture. Subsequent strict thermodynamic derivation led to a formula for the hydration number which resembled that of Onori rather than the original one. Passynski's number turned out to be inconsistent with the thermodynamics and mechanics of fluids. This is a rather purely empirical measure of the slope of the dependence of isentropic compressibility on the solute mole fraction in a dilute aqueous solution. Being the quotient of the slope and the isentropic compressibility of pure water, Pasynski's numbers are more convenient to analyze and discuss than the slopes themselves. Conclusions about molecular interactions based on these numbers must be treated with considerable caution. [ABSTRACT FROM AUTHOR]

To address the high energy consumption of the carbon capture and storage process in the shipping industry, the effects of several commonly used commercial catalysts, such as HZSM-5-25, γ-Al2O3, and SiO2, as well as a self-prepared catalyst, Zr-HZSM-5-25, on the regeneration of MEA solution and MEA + MDEA mixed solution were investigated in this paper. The results showed that Zr-HZSM-5-25 had the best catalytic effect on the regeneration process of the MEA aqueous solution, which could increase the instantaneous maximum CO2 regeneration rate of the MEA-rich solution by about 8.25% and the average regeneration rate by about 5.28%. For the MEA + MDEA mixed solution, the reaction between tertiary amine MDEA and CO2 produced a large amount of HCO3− in the reaction system, which could accelerate the release of CO2 to a large extent, which resulted in the catalytic effect of the Zr-HZSM-5-25 catalyst on the regeneration process of the mixed amine solution being significantly lower than that on the single MEA solution, with an increase of 4.91% in the instantaneous maximum regeneration rate. This instantaneous maximum regeneration rate was only increased by 4.91%. While Zr-HZSM-5-25 showed a better performance in the bench-scale test, it reduced CO2 regeneration energy consumption by 7.3%. [ABSTRACT FROM AUTHOR]

Xenobiotics, which include a wide range of synthetic chemicals and compounds, have become a significant threat to water quality and biodiversity. The need for innovative and sustainable solutions to mitigate the impact of pollutants on our ecosystems has become a hot topic of numerous discussions and research. One such solution lies in the potential application of simulated solar radiation and hydrogen peroxide to remove pesticides from aqueous solutions. In this paper, we investigated the possibility of removing selected pesticides (acetamiprid, clothianidin, and thiacloprid) under the influence of simulated solar radiation with and without the presence of hydrogen peroxide (H2O2). The influence of pH value and H2O2 concentration on removal and toxicity before and after photolytic removal was examined. The results showed that clothianidin is almost completely removed (94.80–96.35%) after 5 h under the influence of simulated solar radiation, while thiacloprid and acetamiprid confirm their persistence and resistance to photolytic degradation. The addition of H2O2 leads to the removal of all three pesticides and results in a significant acceleration of the degradation process itself and the removal of the individual pesticides already within 2 h. According to the data obtained, the k values obtained in the paper follow the following trend: clothianidin > thiacloprid > acetamiprid. [ABSTRACT FROM AUTHOR]

The development of chemosensors able to detect analytes in a variety of sample matrices through a low-cost, fast, and direct approach is of current interest in food, health, industrial, and environmental fields. This contribution presents a simple approach for the selective and sensitive detection of Cu2+ ions in aqueous solution based on a transmetalation process of a fluorescent substituted Zn(salmal) complex. Transmetalation is accompanied by relevant optical absorption changes and quenching of the fluorescence emission, leading to high selectivity and sensitivity of the chemosensor, with the advantage of not requiring any sample pretreatment or pH adjustment. Competitive experiments demonstrate a high selectivity of the chemosensor towards Cu2+ with respect to the most common metal cations as potential interferents. A limit of detection down to 0.20 μM and a dynamic linear range up to 40 μM are achieved from fluorometric data. By exploiting the fluorescence quenching upon formation of the copper(II) complex, simple paper-based sensor strips, visible to naked eyes under UV light, are used for the rapid, qualitative, and quantitative in situ detection of Cu2+ ions in aqueous solution over a wide concentration range, up to 10.0 mM, in specific environments, such as in industrial wastewater, where higher concentrations of Cu2+ ions can occur. [ABSTRACT FROM AUTHOR]

Ethanol possesses high economic value, but as an industrial waste, it poses harm to human health and the environment. The paper describes the preparation of a thermoplastic polyurethane-poly(n-isopropylacrylamide) (TPU-PNIPAM) copolymer designed to selectively uptake alcohol in aqueous solution. The material was created by bonding TPU and PNIPAM together through intermolecular hydrogen bonds, enhancing its hydrophobic properties and making it easier to interact with alcohol molecules. As the amount of PNIPAM in TPU increases, the number of hydrophobic isopropyl groups in TPU-PNIPAM also increases, leading to an enhanced selective uptake ability of TPU-PNIPAM for alcohols in aqueous solution. When the temperature reaches 55 °C, the hydrophobic groups in TPU-PNIPAM are more exposed, further enhancing the selective uptake ability of TPU-PNIPAM for alcohols in aqueous solution. TPU-PNIPAM demonstrates selective preferential uptake for various concentrations and types of alcohol in aqueous solutions. The material's selective uptake performance for alcohols increases with their hydrophobicity, so TPU-PNIPAM exhibited the best adsorption performance for a 10 wt% n-propanol solution under the combined effect of steric hindrance. In addition, TPU-PNIPAM exhibited selective adsorption for other organic solvents, which demonstrated the universality of TPU-PNIPAM in removing contaminants from aqueous solutions. [ABSTRACT FROM AUTHOR]

This paper studies the dynamics of the development of laser breakdown plasma in aqueous colloids of dysprosium nanoparticles by analyzing the time patterns of plasma images obtained using a high-speed streak camera. In addition, the distribution of plasma flashes in space and their luminosity were studied, and the amplitude of acoustic signals and the rate of generation of new chemical products were studied depending on the concentration of dysprosium nanoparticles in the colloid. Laser breakdown was initiated by pulsed radiation from a nanosecond Nd:YAG laser. It is shown that the size of the plasma flash, the speed of motion of the plasma–liquid interface, and the lifetime of the plasma flash decrease with an increasing concentration of nanoparticles in the colloid. In this case, the time delay between the beginning of the laser pulse and the moment the plasma flash reaches its maximum intensity increases with increasing concentrations of nanoparticles. Varying the laser fluence in the range from 67 J/cm2 to 134 J/cm2 does not lead to noticeable changes in these parameters, due to the transition of the breakdown plasma to the critical regime. For dysprosium nanoparticles during laser breakdown of colloids, a decrease in the yield of hydrogen peroxide and an increase in the rate of formation of hydroxyl radicals per water molecule, characteristic of nanoparticles of rare earth metals, are observed, which may be due to the participation of nanoparticles and hydrogen peroxide in reactions similar to the Fenton and Haber–Weiss reactions. [ABSTRACT FROM AUTHOR]

In this paper, we studied the scandium adsorption from aqueous solutions on the surface of low-temperature-activated alumina products (GDAH). The GDAH samples are industrially manufactured, coming from the Bayer production cycle of the Sierra Leone bauxite as aluminium hydroxide, and further, by drying, milling, classifying and thermally treating up to dehydroxilated alumina products at low temperature. All experiments related to hydroxide aluminium activation were conducted at temperature values of 260, 300 and 400 °C on samples having the following particle sizes: <10 µm, 20 µm, <45 µm and <150 µm, respectively. The low-temperature-activated alumina products were characterised, and the results were published in our previous papers. In this paper, we studied the scandium adsorption process on the above materials and related thermodynamic and kinetic studies. [ABSTRACT FROM AUTHOR]

Characterizing molecular interactions at the microscopic level remains difficult and, therefore, represents a key target to better understand macromolecule and biomacromolecule behaviors in solution, alone, or in mixtures with others. Therefore, accurate characterization in liquid media, especially in aqueous solutions, without causing any perturbation of the system in which they are studied, is quite difficult. To this purpose, the present paper describes an innovative methodology based on fluorescence spectrophotometry. Two molecular fluorescent probes, namely 8-anilino-1-naphtalenesulfonic acid (ANS) and 2-benzofuryl-3-hydroxy-4(1H)-quinolone (3HQ-Bf), were selected to characterize, respectively, the dipole-dipole interactions and hydrophobic micro-domains, for the first one, and hydrogen bonding, for the second. As a support to study molecular interactions, xanthan, galactomannan, and corresponding mixtures of these substances which are well known to exhibit a synergy of interactions in well-defined mixture conditions were chosen. Once the methodology was set up, the existence of the three types of interactions in these systems was demonstrated, thus allowing the elucidation of the mechanisms of interactions at the molecular scale. [ABSTRACT FROM AUTHOR]

This paper presents the preparation and characterization of bentonite coated with hydroxide double lamellar Mg/Al-bentonite and Zn/Al-bentonite as a potential adsorbent material. The coating process involved co-precipitation of mixed metal nitrate solution (Mg-Al) or (Zn-Al), followed by immersion of bentonite (B-Na+) dispersion. The structures and morphologies of the coated bentonites were characterized using XRD, FTIR, BET, and SEM analysis. The results of the BET analysis indicate that Mg/Al-bentonite and Zn/Al-bentonite have larger surface areas and pore volumes compared to bentonite alone. Specifically, the surface area of Mg/Al-bentonite is 209.25 m2/g with a pore volume of 0.423 cm3/g, while Zn/Al-bentonite has a surface area of 175.95 m2/g and a pore volume of 0.313 cm3/g. In contrast, the surface area and pore volume of bentonite alone are 110.43 m2/g and 0.132 cm3/g, respectively. The Mg/Al-bentonite reaches 85% uptake within 3 h (equivalent to 724.20 mg/g at 25 °C and pH 7), achieving rapid equilibrium. In contrast, the Zn/Al-bentonite achieves a maximum adsorption of 74% within 5 h under identical pH and temperature conditions, corresponding to 650.34 mg/g. The error function values, including the correlation coefficient R2, chi-square test χ2, and residual sum of squares RSS, were calculated to evaluate both kinetic and isotherm models. The kinetic adsorption data agreed well with a pseudo-second-order model. The adsorption process followed the Sips isotherm model, and the monolayer adsorption capacity of Mg/Al-bent and Zn/Al-bent composites was 872.41 (R2 = 0.974) and 678.45 mg/g (R2 = 0.983), respectively. The thermodynamic analysis of the adsorption process revealed that it occurred spontaneously with an endothermic characteristic. The parameters ΔS, ΔH, and ΔG were used to determine this. [ABSTRACT FROM AUTHOR]

There is an increasing concern about the presence of various types of pharmaceuticals in drinking water, as long-term exposure of people to even low concentrations of drugs can lead to many problems, such as endocrine disorders or drug resistance. As the removal in sewage treatment plants is not effective enough, as indicated, among others, by the EC and OECD reports, it is justified to search for new materials that will allow for an effective and rapid reduction of these pollutants in water. Therefore, in our work, catalytically active nanomaterials containing platinum group metals (PGMs) were synthesized from model and real multicomponent solutions and examined in reactions of organic compounds. The nanoparticles (NPs) were obtained from real solutions from the hydrometallurgical processing of spent automotive converters (SACs), and to the best of our knowledge, the novelty of the proposed paper is the application of solutions from SAC processing as precursors for PGM–NPs. The synthesized PGM–NPs were deposited on a support (TiO2), characterized and, finally, examined as nanocatalysts in a degradation reaction of ibuprofen (IB) from model aqueous solutions. The degree of IB degradation reached more than 90%. The main products of IB degradation were p-isobutylphenol and CO2. [ABSTRACT FROM AUTHOR]

Copper metal ions (Cu2+) are widely used in various industries, and their salts are used as supplementary components in agriculture and medicine. As this metal ion is associated with various health issues, it is necessary to detect and monitor it in environmental and biological samples. In the present report, we synthesized a naphthoquinoline-dione-based probe 1 containing three ester groups to investigate its ability to detect metal ions in an aqueous solution. Among various metal ions, probe 1 showed a vivid color change from yellow to colorless in the presence of Cu2+, as observed by the naked eye. The ratiometric method using the absorbance ratio (A413/A476) resulted in a limit of detection (LOD) of 1 µM for Cu2+. In addition, the intense yellow-green fluorescence was quenched upon the addition of Cu2+, resulting in a calculated LOD of 5 nM. Thus, probe 1 has the potential for dual response toward Cu2+ detection through color change and fluorescence quenching. 1H-NMR investigation and density functional theory (DFT) calculations indicate 1:1 binding of the metal ion to the small cavity of the probe comprising four functional groups: the carbonyl group of the amide (O), the amino group (N), and two t-butyl ester groups (O). When adsorbed onto various solid surfaces, such as cotton, silica, and filter paper, the probe showed effective detection of Cu2+ via fluorescence quenching. Probe 1 was also useful for Cu2+ sensing in environmental samples (sea and drain water) and biological samples (live HeLa cells). [ABSTRACT FROM AUTHOR]

While tremendous efforts have been dedicated to developing cellulose-based ultraviolet (UV)-blocking films, challenges still remain in simultaneously achieving high transparency, low haze and excellent UV shielding properties via simple and green strategy. Here, we present a facile and eco-friendly route to fabricate flexible, biodegradable and clear UV-shielding nano-MIL-88A(Fe)@carboxymethylated cellulose films (M(Fe)CCFs) via in situ synthesis of nano-MIL-88A(Fe) in carboxymethylated cellulose hydrogel followed by natural drying. The carboxymethylated cellulose film has high transmittance (93.2%) and low haze (1.8%). The introduction of nano-MIL-88A(Fe) endowed M(Fe)CCFs superior UV-shielding ability, while retaining high transmittance (81.5–85.3%) and low haze (2.5–4.9%). Moreover, M(Fe)CCFs showed stable UV blocking performance under UV irradiation, high temperature, acidic or alkaline conditions. Quite encouragingly, the UV-shielding ability of M(Fe)CCFs did not deteriorate, even after 30 days of immersion in aqueous solution, providing films with a long-term use capacity. Thus, M(Fe)CCFs show high potential in the UV protection field. Overall, these UV-blocking films with outstanding performances are a promising candidate to replace conventional film materials made from synthetic polymers in fields such as packaging and flexible electronics. [ABSTRACT FROM AUTHOR]

The aim of endodontic therapy is to use various antimicrobial medications for proper cleaning and shaping to create an environment free of microorganisms by eradicating as many as possible from the root canal space. Even although it is a gold standard irrigant, sodium hypochlorite (NaOCl) is known for its cytotoxic effects on vital periapical tissues, making its higher concentrations inappropriate for use in conditions such as wide, underdeveloped, or damaged apices and in cases of perforations. Consequently, if it is ascertained that a gel form of sodium hypochlorite has equivalent antibacterial activity to the aqueous solution form, it could be employed in such situations. The aim of this study was the microbiologic evaluation of 5.25% sodium hypochlorite gel and aqueous solution as root canal disinfectants in multirooted teeth with primary endodontic lesions. Following ethical approval and CTRI registration, 42 patients who gave their consent and had multirooted teeth with pulpal necrosis and asymptomatic apical periodontitis were considered for the study. Following the opening of the access, pre-endodontic build up in case of class-II cavities and working length determination, a pre-operative sample (S1), which was regarded as the pre-operative microbial load of that canal, was acquired from the largest canal using a sterile paper point while maintaining strict isolation and disinfection. The computer randomization approach was used to divide the teeth into two groups at random just before beginning of chemo-mechanical preparation: Group A (n = 21)—canal disinfection with 5.25% sodium hypochlorite gel; Group B (n = 21)—canal disinfection with 5.25% sodium hypochlorite aqueous solution. Following the canal disinfection, a post-operative (S2) sample which was regarded as the postoperative microbial load of that canal was collected from the same canal using a sterile paper point. The Colony-Forming Units (CFUs) for the S1 and S2 samples were determined after 48 h aerobic incubation on Brain Heart Infusion (BHI) agar plates. The patients and the microbiologist were blinded throughout the procedure. Using SPSS 20.0 software (USA), the Shapiro–Wilk test and the Lilliefors Significance Correction were used for normality, followed by the Mann–Whitney U test which was used to compare the CFU difference (×105) between the two groups. A p value of <0.05 was perceived as statistically significant. The mean colony-forming units count difference between the 5.25% sodium hypochlorite gel and aqueous solution groups did not differ in a manner that was statistically significant (p = 0.744). In multirooted teeth with primary endodontic lesions, the 5.25% sodium hypochlorite gel and the aqueous solution demonstrated comparable antimicrobial effectiveness when implemented as root canal disinfectants. [ABSTRACT FROM AUTHOR]

The purpose of this paper is to develop SRF formulations for LHP performance enhancement. In this paper, the solute of SRF is prepared, and butanol and its isomer, 2-butanol, are selected. In this paper, concentrations of the 2-butanol aqueous solution (10%, 15%, and 20%) plus the butanol 6% aqueous solution were used to measure the surface tension of four different formulations of SRF and water. It was found that the higher the solute concentration became, the stronger the Marangoni effect was, and the more obvious the surface tension change of the 2-butanol 20% aqueous solution was. Water, the butanol 6% aqueous solution and the 2-butanol 20% aqueous solution were filled into LHP respectively, and the heat transfer performance was measured. The 2-Butanol 20% aqueous solution improved LHP performance by about three times compared with water, and the lowest total thermal resistance was only 1/4 that of water. Therefore, the 2-butanol 20% SRF aqueous solution is an ideal formula for improving the LHP heat transfer performance. [ABSTRACT FROM AUTHOR]

This work is focused on the age-old challenge of developing optical sensors for acidity measurements in low-pH aqueous solutions (pH < 5). We prepared halochromic (3-aminopropyl)amino-substituted quinoxalines QC1 and QC8 possessing different hydrophilic–lipophilic balance (HLB) and investigated them as molecular components of pH sensors. Embedding the hydrophilic quinoxaline QC1 into the agarose matrix by sol-gel process allows for fabrication of pH responsive polymers and paper test strips. The emissive films thus obtained can be used for a semi-quantitative dual-color visualization of pH in aqueous solution. Being exposed to acidic solutions with pH in the range of 1–5, they rapidly give different color changes when the analysis is performed in daylight or under irradiation at 365 nm. Compared with classical non-emissive pH indicators, these dual-responsive pH sensors allow for an increase in the accuracy of pH measurements, particularly in complex environmental samples. pH indicators for quantitative analysis can be prepared by the immobilization of amphiphilic quinoxaline QC8 using Langmuir–Blodgett (LB) and Langmuir–Schäfer (LS) techniques. Compound QC8 possessing two long alkyl chains (n-C8H17) forms stable Langmuir monolayers at the air–water interface, and these monolayers can be successfully transferred onto hydrophilic quartz and hydrophobic polyvinylchlorid (PVC) substrates using LB and LS techniques, respectively. The 30-layer films thus obtained are emissive, reveal excellent stability, and can be used as dual-responsive pH indicators for quantitative measurements in real-world samples with pH in the range of 1–3. The films can be regenerated by immersing them in basic aqueous solution (pH = 11) and can be reused at least five times. [ABSTRACT FROM AUTHOR]

In this paper, a highly efficient and straightforward method for synthesizing novel Schiff bases was developed by reacting selected biogenic amines with sodium 2-formylbenzene sulfonate and sodium 3-formylbenzene sulfonate. 1H and 13C NMR, IR spectroscopy, and high-resolution mass spectrometry were used to characterize the new compounds. The main advantages of the proposed procedure include simple reagents and reactions carried out in water or methanol and at room temperature, which reduces time and energy. Moreover, it was shown that the obtained water-soluble Schiff bases are stable in aqueous solution for at least seven days. Additionally, the antioxidant and antimicrobial activity of synthesized Schiff bases were tested. [ABSTRACT FROM AUTHOR]

Biochar gained attention due to its definite physico-chemical characteristics and because it is a cost-effective and efficient adsorbent. In this paper, commercial biochar was tested for the removal of tartrazine from aqueous solutions. Thus, the optimum experimental conditions were determined for several parameters (pH, temperature, initial concentration of tartrazine, biochar dose, and contact time). The concentration of tartrazine residues was determined using UV-Vis spectrophotometry. The best experimental results were obtained at 1 mg L−1 concentration of tartrazine, pH 2, 30 °C, 18 min, and 0.9 g L−1 adsorbent dose. The maximum removal efficiency of tartrazine obtained in optimum conditions was 90.18%. The experimental data were analyzed by the isotherm and kinetic models. The isotherm and kinetics of tartrazine removal on biochar follow the Langmuir isotherm and pseudo-second-order kinetics, respectively. According to the Langmuir isotherm model, the biochar showed a maximum adsorption capacity of 3.28 mg g−1. In addition, biochar demonstrated a good reuse potential and therefore can be used for the removal of tartrazine from aqueous solutions. [ABSTRACT FROM AUTHOR]

In this study, a new strategy was adopted for obtaining polymer/protein hybrid hydrogels with shape stability and tunable mechanical or rheological characteristics by using non-toxic procedures. A chemical network was created using a poly(vinyl alcohol)(PVA)/bovine serum albumin (BSA) mixture in aqueous solution in the presence of genipin and reduced glutathione (GSH). Then, a second physical network was formed through PVA after applying freezing/thawing cycles. In addition, the protein macromolecules formed intermolecular disulfide bridges in the presence of GSH. In these conditions, multiple crosslinked networks were obtained, determining the strengthening and stiffening into relatively tough porous hydrogels with tunable viscoelasticity and a self-healing ability. A SEM analysis evidenced the formation of networks with interconnected pores of sizes between 20 μm and 50 μm. The mechanical or rheological investigations showed that the hydrogels' strength and response in different conditions of deformation were influenced by the composition and crosslinking procedure. Thus, the dynamics of the hybrid hydrogels can be adjusted to mimic the viscoelastic properties of the native tissues. The dynamic water vapor-sorption ability, swelling behavior in an aqueous environment, and bioadhesive properties were also investigated and are discussed in this paper. The hybrid hydrogels with tunable viscoelasticity can be designed on request, and they are promising candidates for tissue engineering, bioinks, and wound dressing applications. [ABSTRACT FROM AUTHOR]

Highlights: A new gelatin composite was used to remove methylene blue. The adsorbent was composed of carbon nanotubes, a metal–organic framework and gelatin. The adsorbent had a simple preparation process and was friendly to the environment. The fixation of carbon nanomaterials with gelatin as the substrate avoided secondary pollution. Using carbon nanotubes as the intermediate improved the adsorption capacity. A novel gelatin-based functionalized carbon nanotubes@metal–organic framework (F-CNTs@MOF@Gel) adsorbent was prepared by the green and simple method for the adsorption of methylene blue (MB). Cu-BTC (also known as HKUST-1) was selected as the MOF type. F-CNTs@Cu-BTC particles were fixed by gelatin, thus avoiding the secondary pollution of carbon nanomaterial particles to the environment. CNTs were used as the connecting skeleton to make more effective adsorption sites exposed on the surface of the internal pore structure of the adsorbent. In this paper, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), powder X-ray diffraction (XRD), thermogravimetry (TGA) and BET analysis methods were used to characterize the new adsorbent. The effects of time, temperature, pH, dosage and initial concentration on the adsorption process were investigated by batch adsorption experiments. The adsorption mechanism was further analyzed by several commonly used kinetic and isotherm models, and the reliability of several fitting models was evaluated by the Akaike information criterion (AIC), Bayesian information criterion (BIC) and Hannan information criterion (HIC). After five regeneration experiments, the adsorbent still had 61.23% adsorption capacity. In general, the new adsorbent studied in this paper has an optimistic application prospect. [ABSTRACT FROM AUTHOR]

The rheological behavior of polyvinyl alcohol (PVA) aqueous solution is crucial to optimizing the processing technology and performance of PVA products. In this paper, the dynamic rheological behavior of PVA aqueous solution was investigated in detail. PVA solution with a concentration of 10 wt% showed unnormal rheological behaviors, that is, the liquid-like behavior in the high frequency (ω) region and the solid-like behavior in the low ω region. A storage modulus (G′) plateau appears in the relatively low ω region as a gel with a network structure. Different from conventional hydrogel, this plateau has a low modulus, and the corresponding size of the relaxation unit is estimated to be 554 nm, being higher than the size of a whole PVA chain. It is believed that the network mesh is formed by the intermolecular hydrogen bonding interactions among PVA chains. The relaxation time of these meshes is longer than the reptation time of a PVA chain. Based on the relaxation spectrum and calculation analysis, it is found that the destruction of intermolecular hydrogen bonds, such as by heating up, adding sodium dodecyl sulfate, and shear operation, will make the relaxation unit (mesh) larger and lead to the left shift of the intersection of G′ and loss modulus (G″). In a PVA solution with a high concentration, multiple meshes of various sizes could be formed and thus generate multiple relaxation peaks. The large-sized meshes mainly contribute to the left shift of the intersection of G′ and G″, and the small-sized meshes contribute to the high plateau modulus. The results in this paper offer a new angle to analyze polymer solutions with strong intermolecular interaction. [ABSTRACT FROM AUTHOR]

This paper reports the synthesis of a novel quaternary surfactant containing a hydroxyethyl group (PFPE-C) and the surface properties of its aqueous solution (investigated by comparisons with two structurally similar chemicals, dodecyl-(2-hydroxyethyl)-dimethylammonium chloride (DHDAC) and PFPE-A). The minimum surface tension ( γ C M C ) and critical micelle concentration (CMC) of the PFPE-C aqueous solution were 17.35 mN/m and 0.024 mmol/L, respectively. This study confirms that surfactants containing hydroxyethyl groups efficiently reduce the surface tension of aqueous solutions, and fluorocarbon surfactants exhibit better surface activity than ordinary hydrocarbon surfactants with similar structures. The micellization, aggregation, air-water interfacial adsorption, and wettability of PFPE-C aqueous solutions have been systematically investigated. Highly concentrated PFPE-C aqueous solutions exhibit good wettability on PTFE and paraffin films. Moreover, the aggregates of PFPE-C in the aqueous solution were clearly seen as vesicles on Cryo-TEM micrographs. Primary biodegradation results indicate that 19% of PFPC-C can be degraded within one week. [ABSTRACT FROM AUTHOR]

Biocatalysis can be applied in aqueous media and in different non-aqueous solutions (non-conventional media). Water is a safe solvent, yet many synthesis-wise interesting substrates cannot be dissolved in aqueous solutions, and thus low concentrations are often applied. Conversely, non-conventional media may enable higher substrate loadings but at the cost of using (fossil-based) organic solvents. This paper determines the CO2 production—expressed as kg CO2·kg product−1—of generic biotransformations in water and non-conventional media, assessing both the upstream and the downstream. The key to reaching a diminished environmental footprint is the type of wastewater treatment to be implemented. If the used chemicals enable a conventional (mild) wastewater treatment, the production of CO2 is limited. If other (pre)treatments for the wastewater are needed to eliminate hazardous chemicals and solvents, higher environmental impacts can be expected (based on CO2 production). Water media for biocatalysis are more sustainable during the upstream unit—the biocatalytic step—than non-conventional systems. However, processes with aqueous media often need to incorporate extractive solvents during the downstream processing. Both strategies result in comparable CO2 production if extractive solvents are recycled at least 1–2 times. Under these conditions, a generic industrial biotransformation at 100 g L−1 loading would produce 15–25 kg CO2·kg product−1 regardless of the applied media. [ABSTRACT FROM AUTHOR]

The paper proposed a new porous material for wound healing based on chitosan and C-phycocyanin (C-PC). In this work, C-PC was extracted from the cyanobacteria Arthrospira platensis biomass and purified through ammonium sulfate precipitation. The obtained C-PC with a purity index (PI) of 3.36 ± 0.24 was loaded into a chitosan sponge from aqueous solutions of various concentrations (250, 500, and 1000 mg/L). According to the FTIR study, chitosan did not form new bonds with C-PC, but acted as a carrier. The encapsulation efficiency value exceeded 90%, and the maximum loading capacity was 172.67 ± 0.47 mg/g. The release of C-PC from the polymer matrix into the saline medium was estimated, and it was found 50% of C-PC was released in the first hour and the maximum concentration was reached in 5–7 h after the sponge immersion. The PI of the released C-PC was 3.79 and 4.43 depending on the concentration of the initial solution. [ABSTRACT FROM AUTHOR]

A nanofluidic system consists of a nano-porous medium and functional liquid, which demonstrates a higher energy absorption density compared to conventional systems for energy absorption. Alterations in the composition of the functional liquid can significantly impact the properties of a nanofluidic system. In this paper, the widely used zeolite ZSM-5 was chosen as the porous medium to establish a nanofluidic system. Three distinct electrolyte solutions, namely KCl aqueous solutions, NaCl aqueous solutions and MgCl2 aqueous solutions were employed as functional liquids while pure water served as the reference condition for configuring four kinds of nanofluidic systems. Pressure-induced percolation experiments were performed on the four zeolite-based systems. The difference in the infiltration process between the electrolyte solution systems and the deionized water system has been ascertained. The effect of the ion size on the infiltration and defiltration process has been determined. The results show that the introduction of ions induces a hydration effect, resulting in a higher critical infiltration pressure of the electrolyte solution system compared to an aqueous solution system. The magnitude of cation charge directly correlates with the strength of the hydration effect and the corresponding increase in critical infiltration pressure. Upon entering the nanochannel, the liquid infiltrates primarily in the form of ions rather than a cation hydration form. The larger the ion size, the shallower the penetration depth after entering the nanopore channel and the larger the corresponding relative outflow rate. The present work will provide valuable theoretical complementary and experimental data support for nanofluidic system applications. [ABSTRACT FROM AUTHOR]

The phenomenon of the formation of microheterogeneities (MHs) in solutions, which, according to chemical handbooks, are considered true solutions, has been known for a long time. MHs have been found in more than 100 binary solutions, many of which are used both in various scientific studies and in life. However, the nature of this phenomenon is largely unclear. It is only well-known that MHs are stable areas of increased concentration of one of the components of the solution. The main reason for the poor knowledge of MHs is the use of very few experimental methods, mainly light scattering methods. In this paper, the terahertz time-domain spectroscopy method was used for the first time to study MHs using the example of aqueous solutions of three sugars: glucose, fructose, and sucrose. This method gives the spectra of complex permittivity in the terahertz range, which are very informative when studying the hydrate shells of molecules in solutions. The idea of this study was that structuring sugar molecules with the formation of MHs changes their hydration. The characteristics of sugar hydration in solutions before and after filtration through a 20 nm filter, leading to the destruction of MHs, were compared. It has been shown that the water binding in the MHs of all three solutions is increased compared with the hydrate shells of individual sugar molecules. Also, for MHs' fructose solution, a decrease in the number of hydrogen bonds between water molecules and an increase in the number of free water molecules was shown, which is not observed in MH glucose and sucrose solutions. This is explained by mutarotations of fructose molecules, leading to permanent significant rearrangements of the water structure in MHs. Thus, terahertz time-domain spectroscopy provides fundamentally new information about the MHs of aqueous solutions at the level of their hydration characteristics. The presence of MHs in solutions is a significant factor that has never been taken into account when studying the hydrate shells of various molecules in solutions using THz spectroscopy. [ABSTRACT FROM AUTHOR]

The reaction of CF3COOAg, 3-bdppmapy (N,N-bis(diphenylphosphanylmethyl)-3-aminopyridine) and HTZ (1,2,4-triazole-3-thiol) in CH2Cl2/MeOH resulted in a dinuclear Ag/P/S complex [Ag2(TZ)2(3-bdppmapy)2]·xSol (1·xSol). Crystals of 1·xSol converted to 1·2MeOH in air at room temperature and further to 1 under vacuum upon heating. The solid-state, room-temperature photoluminescent emission of 1·xSol (510 nm) shifted to 494 nm (1·2MeOH) and 486 nm (1). Grinding solids of 1·2MeOH in air resulted in amorphous 1G characterized by solid-state emission at 468 nm, which converted to 1GR with 513 nm emission upon MeOH treatment. Grinding 1GR in air returned 1G, and this interconversion was reproducible over five cycles. The solid-state photoluminescence of 1G changed in response to vapors containing low–molecular weight alcohols but remained unchanged after exposure to other volatile organic compounds (VOCs) or to water vapor. Test papers impregnated with 1G could detect methanol in vapors from aqueous solutions at concentrations above 50%. Complex 1G is, therefore, an example of a stimuli-responsive molecular sensor for the detection of alcohols. [ABSTRACT FROM AUTHOR]

The paper investigates the physicochemical processes that occur during laser-induced breakdown in colloids of gadolinium oxide nanoparticles of different concentrations. A monotonic change in the number of optical breakdowns, the average distance between the nearest breakdowns in the track of a single laser pulse, the average plasma size of a single optical breakdown, the integral luminosity of an optical breakdown plasma flash, the intensity of acoustic signals, and the rate of formation of dissociation products—O2, H2, OH•, and H2O2—is demonstrated. It is shown that the rate of formation of chemical products of the decomposition of H2O molecules under the action of breakdown when using nanoparticles of rare earth metals, in particular, gadolinium oxide, is the highest compared to other materials. Based on one laser pulse, the rates of formation of chemical products formed during the dissociation of water during laser-induced breakdown of a colloid of gadolinium oxide nanoparticles are 13.13 nmol/pulse for H2, 5.41 nmol/pulse for O2, and 6.98 nmol/pulse for hydrogen peroxide. [ABSTRACT FROM AUTHOR]

The removal of hazardous heavy metals that have been released into the environment due to industrial activities has become an important issue in recent years. The presented study concerned the removal of copper(II) ions from aqueous solutions using dolomites. Dolomite is a very attractive adsorbent due to its wide availability, low cost, good adsorption, and environmental compatibility. The paper describes the properties of D-I and D-II dolomites from two different open-cast mines in Poland. The properties of natural adsorbents were determined based on point of zero charges (PZC), elemental analysis of the adsorbent composition, FT-IR, XRD, and SEM spectra analysis. Depending on the initial concentration of the solution used, the adsorption efficiency of copper(II) ions was 58–80% for D-I and 80–97% for D-II. The adsorption mechanism in the case of D-II dolomite was mainly based on ion exchange, while chemisorption dominated the D-I dolomite surface. Considering the possibility of the regeneration and reuse of the adsorbent, dolomite D-II is a better material (the desorption efficiency of copper(II) ions was 58–80%). The adsorption behavior of dolomites has been described using six adsorption isotherms. The best fit was obtained for the Redlich–Peterson, Jovanović, and Langmuir isotherms, indicating that monolayer adsorption occurred. The maximum adsorption capacity for copper(II) was 378 mg/g of D-I and 308 mg/g of D-II. [ABSTRACT FROM AUTHOR]

This paper describes a single-stage synthesis process for activated carbon using cherry seeds. The influences of the carbonization temperature and the time were investigated. Using the BET method, the surface area of the obtained activated carbons was determined, as well as the pore distribution, while SEM images provided further insight into the structure of the surface. Next, the adsorption isotherm was derived. For the test, Pd(II) chloride complex ions were used. It was found that the obtained activated carbon were suitable for palladium(II) recovery from diluted aqueous solutions. Out of the tested parameters of carbon synthesis, the most optimal one was found to be 500 °C for 3 h. Additionally, it was confirmed that the increase in the adsorption temperature affects the increase in palladium load from 1.6 mg/g at 20 °C to 15.6 mg/g at 50 °C (for the best-performing sample). This fact may suggest that the process of adsorption is associated with chemical reactions. [ABSTRACT FROM AUTHOR]

The separation of Rare Earth Elements (REEs) is an important step in the valorization of REE ore and aims at producing individual rare earth compounds for the market. The separation is carried out industrially by solvent extraction (SX) using interconnected circuits consisting of cascades of mixer-settlers. The design of a REE separation circuit implies the selection of the operating conditions and of the number of mixer-settlers required to achieve a target degree of purity for the separated elements. This design work is either carried out by piloting a circuit or using a mathematical simulation. Independent of the method, the world expertise in this area is limited. This paper describes a simulation method requiring a minimum of calibration effort, which can be used to design a complete REE separation plant. The simulation enables assessment of the effect of the number of mixer-settlers per extraction, the scrubbing and stripping stage, as well as the pH of the aqueous solution and organic-phase contents of free and loaded extractant on the purity of the separated REEs. The simulation tool presented here has been developed from a fundamental analysis of the chemical reactions involved in the solvent extraction process. Unlike most of the simulation methods documented in the literature, the method requires no empirical calibration. The proposed method is validated using data from laboratory batch tests and with published data from continuous pilot and industrial REE separation circuits. The application of the simulation tool is illustrated with the planning of the test conditions for a forthcoming pilot test work and with the simulation of a 9-REE product SX separation plant. [ABSTRACT FROM AUTHOR]

A synthetic approach has been developed to prepare silica gel monoliths that embed well separated silver or gold spherical nanoparticles (NP), with diameters of 8, 18 and 115 nm. Fe3+, O2/cysteine and HNO3 were all successfully used to oxidize and remove silver NP from silica, while aqua regia was necessary for gold NP. In all cases, NP-imprinted silica gel materials were obtained, with spherical voids of the same dimensions of the dissolved particles. By grinding the monoliths, we prepared NP-imprinted silica powders that were able to efficiently reuptake silver ultrafine NP (Ag-ufNP, d = 8 nm) from aqueous solutions. Moreover, the NP-imprinted silica powders showed a remarkable size selectivity, based on the best match between NP radius and the curvature radius of the cavities, driven by the optimization of attractive Van der Waals forces between SiO2 and NP. Ag-ufNP are increasingly used in products, goods, medical devices, disinfectants, and their consequent diffusion in the environment is of rising concern. Although limited here to a proof-of-concept level, the materials and methods described in this paper may be an efficient solution for capturing Ag-ufNP from environmental waters and to safely dispose them. [ABSTRACT FROM AUTHOR]

The paper presents the research results on synthesizing silver nanoparticles in aqueous solutions and their extraction into the organic phase. Studies have shown that it is best to perform the extraction process using n-hexane > cyclohexane > toluene > chloroform > ethyl acetate. The results show a correlation between the dielectric constant of the organic phase and its ability to extract nanoparticles. The lower the dielectric constant is, the higher the extractability. The hydrodynamic radius of the silver nanoparticles changes after transfer to the organic phase, depending greatly on the organic phase used. The extraction mechanism is complex and multi-step. As the first step, the Ag nanoparticles are transferred to the phase boundary. As the second step, the octadecylamine (ODA) molecules adsorb on the silver nanoparticles (AgNPs) surface. The change in particle shape was also noted. This suggests that the interfacial processes are more complex than previously reported. Below the initial concentration of ODA 2 × 10−4 M, the formation of a third phase has been observed. In a one-stage experiment, the concentration of silver nanoparticles after transferring to the organic phase was increased 500 times in about 10 s. The role of the concentration of ODA, therefore, is not only a measure of the extraction efficiency and productivity but functions as an enabler to maintain favorable biphasic processing, which underlines the role of the solvent again. [ABSTRACT FROM AUTHOR]

The aggregation structure of Triton X (TX) amphiphilic molecules in aqueous solution plays an important role in determining the various properties and applications of surfactant solutions. In this paper, the properties of micelles formed by TX-5, TX-114, and TX-100 molecules with different poly(ethylene oxide) (PEO) chain lengths in TX series of nonionic surfactants were studied via molecular dynamics (MD) simulation. The structural characteristics of three micelles were analyzed at the molecular level, including the shape and size of micelles, the solvent accessible surface area, the radial distribution function, the micelle configuration, and the hydration numbers. With the increase of PEO chain length, the micelle size and solvent accessible surface area also increase. The distribution probability of the polar head oxygen atoms on the surface of the TX-100 micelle is higher than that in the TX-5 or TX-114 micelle. In particular, the tail quaternary carbon atoms in the hydrophobic region are mainly located at the micelle exterior. For TX-5, TX-114, and TX-100 micelles, the interactions between micelles and water molecules are also quite different. These structures and comparisons at the molecular level contribute to the further understanding of the aggregation and applications of TX series surfactants. [ABSTRACT FROM AUTHOR]

The carbon materials derived from discarded masks and lignin are used as adsorbent to remove two types of reactive dyes present in textile wastewater: anionic and cationic. This paper introduces the results of batch experiments where Congo red (CR) and Malachite green (MG) are removed from wastewater onto the carbon material. The relationship between adsorption time, initial concentration, temperature and pH value of reactive dyes was investigated by batch experiments. It is discovered that pH 5.0–7.0 leads to the maximum effectiveness of CR and MG removal. The equilibrium adsorption capacities of CR and MG are found to be 232.02 and 352.11 mg/g, respectively. The adsorption processes of CR and MG are consistent with the Freundlich and Langmuir adsorption models, respectively. The thermodynamic processing of the adsorption data reveals the exothermic properties of the adsorption of both dyes. The results show that the dye uptake processes follow secondary kinetics. The primary adsorption mechanisms of MG and CR dyes on sulfonated discarded masks and alkaline lignin (DMAL) include pore filling, electrostatic attraction, π-π interactions and the synergistic interactions between the sulphate and the dyes. The synthesized DMAL with high adsorption efficiency is promising as an effective recyclable adsorbent for adsorbing dyes, especially MG dyes, from wastewater. [ABSTRACT FROM AUTHOR]

In this paper, we consider natural and modified polysaccharides for use as active ingredients in scale deposition inhibitors to prevent the formation of scale in oil production equipment, heat exchange equipment, and water supply systems. Modified and functionalized polysaccharides with a strong ability to inhibit the formation of deposits of typical scale, such as carbonates and sulfates of alkaline earth elements found in technological processes, are described. This review discusses the mechanisms of the inhibition of crystallization using polysaccharides, and the various methodological aspects of evaluating their effectiveness are considered. This review also provides information on the technological application of scale deposition inhibitors based on polysaccharides. Special attention is paid to the environmental aspect of the use of polysaccharides in industry as scale deposition inhibitors. [ABSTRACT FROM AUTHOR]

This paper puts forward the use of "low-cost/low-end" hydroxyapatite-based adsorbing materials prepared from Tambaqui fish cleaning residues (i.e., bones) by grinding and/or thermal annealing. The nature of raw materials and treatments practically resulted in a "zero-cost" adsorbent for atrazine pesticide and Co2+ ion remediation in an aqueous solution. Despite the distinctive character of the two contaminants, all adsorptions were found to follow pseudo-second order kinetics and Freundlich isotherm models. Pristine hydroxyapatite proved to be more effective in adsorbing atrazine at low concentrations due to interactions with collagen residues. Conversely, heat-treated materials demonstrated better adsorption performances for cobalt due to the removal of organic residues hindering access to the surface. On the other hand, lower adsorption affinities resulted into a faster and more efficient Co2+ release into water. The different behavior in terms of phosphate and cobalt release shown by the three hydroxyapatite-based absorbents can be exploited for differential liberation of targeted nutrients, with high seed germination rates. Considering circular economic principles, waste-derived hydroxyapatites may be potentially attractive for removing ionic species, minimizing water pollution stemming from heavy industry, and for their subsequent targeted release to edible plants, enhancing agricultural availability of mineral nutrients for soil fertilization. [ABSTRACT FROM AUTHOR]

Lead is one of the most toxic heavy metals released into the environment through industrial sources. Its direct determination is often a problem due to the presence of relatively complex matrices as well as low content. Thus, the additional separation and preconcentration steps are necessary in the analytical procedures. Carbon nanotubes (CNTs) continue to attract significant interest for these purposes as they exhibit a high specific surface area, exceptional porosities, and numerous adsorption sites. The modified CNTs with active groups, reagents, or materials have been widely explored using more mutual interactions that can significantly improve their sorption capacity and selectivity. This paper summarizes the recent developments from 2017 in the application of carbon nanotubes for the separation of Pb(II) and its enrichment/removal from the matrix components. Attention is given to oxidized CNTs, their modification with complexing compounds, functionalization with metal oxides and polymers, new nanocomposites, and carbon nanotube membranes. [ABSTRACT FROM AUTHOR]

Photoreforming (PR) of biomass can be considered a viable technology under mild experimental conditions to produce hydrogen with a high reaction rate using compounds from renewable resources and waste materials. The application of biomass PR gives rise to both hydrogen generation and biomass waste valorization. The process could be scaled up to obtain hydrogen under natural sunlight irradiation, and research on polymeric carbon nitride (g-C3N4)-based photocatalysts has been widely carried out in recent years. The non-metallic-based carbon nitride materials are economical and (photo)stable polymer semiconductors, and their physicochemical surface and electronic properties are optimal for obtaining H2, which can be considered a gas that does not cause major environmental problems. Some hindrances related to their structure, such as the low absorption of visible light and the relatively high recombination rate of electron-hole pairs, restrict the performance; therefore, it is necessary to improve their activity and the yield of the reaction by modifying them in various ways. Various types of solutions have been proposed in this regard, such as, for example, their coupling with other semiconductors to form composite materials. The current mini-review aims to overview the PR field, reporting some of the most interesting papers devoted to understanding the role of g-C3N4 in biomass PR. Information on many physico-chemical aspects related to the performance of the process and possible ways to obtain better results than those present up to now in the literature will be reported. [ABSTRACT FROM AUTHOR]

Direct determination of lead trace concentration in the presence of relatively complex matrices is often a problem. Thus, its preconcentration and separation are necessary in the analytical procedures. Graphene-based nanomaterials have attracted significant interest as potential adsorbents for Pb(II) preconcentration and removal due to their high specific surface area, exceptional porosities, numerous adsorption sites and functionalization ease. Particularly, incorporation of magnetic particles with graphene adsorbents offers an effective approach to overcome the separation problems after a lead enrichment step. This paper summarizes the developments in the applications of graphene-based adsorbents in conventional solid-phase extraction column packing and its alternative approaches in the past 5 years. [ABSTRACT FROM AUTHOR]

Nanotechnologies based on magnetic materials have been successfully used as efficient and reusable strategies to remove pharmaceutical residuals from water. This paper focuses on the fabrication, characterization, and application of ferrite-based magnetic nanoparticles functionalized with L-lysine as potential nanoadsorbents to remove acetylsalicylic acid (ASA) from water. The proposed nanomaterials are composed of highly magnetic and chemically stable core–shell nanoparticles covered with an adsorptive layer of L-lysine (CoFe2O4–γ-Fe2O3–Lys). The nanoadsorbents were elaborated using the coprecipitation method in an alkaline medium, leading to nanoparticles with two different mean sizes (13.5 nm and 8.5 nm). The samples were characterized by XRD, TEM, FTIR, XPS, Zetametry, BET, and SQUID magnetometry. The influence of time, pH, and pollutant concentration was evaluated from batch studies using 1.33 g/L of the nanoadsorbents. The Freundlich isotherm best adjusted the adsorption data. The adsorption process exhibited a pseudo-second-order kinetic behavior. The optimal pH for adsorption was around 4–6, with a maximum adsorption capacity of 16.4 mg/g after 150 min of contact time. Regeneration tests also showed that the proposed nanomaterials are reusable. The set of results proved that the nanoadsorbents can be potentially used to remove ASA from water and provide relevant information for their application in large-scale designs. [ABSTRACT FROM AUTHOR]

It can be observed that magnetic iron-oxide nanoparticles are increasingly used in bioassay methods. This is due to their stability in aqueous solutions, ease of functionalization, biocompatibility and very low toxicity. Here, we show that the recent discovery of the ability of magnetic nanoparticles to self-assemble into 2D structures of ordered chains may be exploited for bioassays. This would open up the possibility of controlled immobilization of proteins, enzymes, DNA or RNA and other molecular systems on spatially ordered nanostructures. In this work, fluorescein was used as an example. Also shown is the possibility of using Raman spectroscopy to analyze material accumulated on such structures. The observed formation of regularly spaced chains of magnetic nanoparticles takes place during the drying process of a thin layer of magnetic liquid placed on an appropriately prepared low-density polyethylene (LDPE) film. [ABSTRACT FROM AUTHOR]