Search

There have been fruitful publications on thermal comfort of urban residential buildings in China. However, there is a lack of reviews on this topic to perform a comprehensive analysis and find opportunities to meet occupants' thermal comfort needs while improving building energy efficiencies. This paper addresses this issue by presenting a systematic review on the advancements in research on thermal comfort in urban residential buildings in China. Firstly, two common thermal comfort research approaches, i.e., field studies and laboratory studies, are discussed. Secondly, eleven main thermal comfort evaluation indicators are summarized. Finally, this paper analyzes the thermal comfort survey data from different researchers, discusses the impacts of adaptive behaviors on human thermal comfort, and provides recommendations for future research on urban residential thermal comfort. It was found that people have higher and higher requirements for their indoor thermal environment as time goes by, especially in the winter; the thermoneutral temperature is higher in warmer climate regions in the summer but lower in the winter than in colder climate regions; the thermoneutral temperature tends to increase with the indoor air temperature due to an adaptation to the indoor thermal environment. The outcomes of this paper provide valuable information on thermal comfort behaviors of urban residents in different climate zones in China, which can serve as a resource for the academic community conducting future research on thermal comfort and assist policymakers in enhancing building energy efficiencies without compromising the occupants' comfort. [ABSTRACT FROM AUTHOR]

High outdoor temperatures and thermal gains due to solar radiation, which penetrates the interior of buildings as the climate warms up, pose a major challenge to maintaining thermal comfort in passive sports facilities. Superbly insulated and airtight envelopes, specific microclimatic requirements and very high user activity can easily lead to overheating and thermal imbalance during summer. This paper focuses on the influence of the varying thermal capacity of external walls and night-time cooling on thermal comfort in a passive sports hall building. Based on experimental studies of the thermal conditions in the building, a model of it was created in Design Builder. Through simulation, the program initially analysed the thermal conditions that arise under different envelope assemblies. Two different ways of cooling the building at night were then analysed: mechanical and natural. The results presented showed that in a well-insulated sports hall with a large volume, the type of wall material alone had only a limited influence on thermal comfort in summer. In contrast, night-time cooling in integration with the accumulation of cold in the building's structural components had a significant impact on protection against overheating during the summer. The type of envelope material is even more important when night-time air exchange is high. Intensive natural ventilation is associated with the highest number of hours in the comfort range—28.1–32.4% more hours in relation to the variant without night ventilation. The use of mechanical ventilation, operating at night at maximum capacity, will result in an increase in the number of hours with air temperatures in the −0.5 < PMV < +0.5 range by only 14.1–21.3%. The high thermal mass of the envelope, combined with adequate ventilation, reduces the occurrence of very high indoor air temperatures, thus alleviating the nuisance of overheating. The maximum internal air temperature during the day is lower by 2.4–3.3 K, compared to the case when no night ventilation is used. Mechanical ventilation operating at its maximum capacity can reduce the maximum internal temperature by 1.2–1.6 K. [ABSTRACT FROM AUTHOR]

The standard for ergonomics of the thermal environment provides information on the calculation of optimal thermal comfort. Operative temperature (OT) is one of the essential elements of thermal comfort and is a function of air temperature, mean radiant temperature (MRT), and air velocity. This paper investigates the impact of diverse influences on MRT in an office room based on occupant position and posture (seated and standing). A comparative simulation study of the varied thermal transmittance (U-value) of the only external wall with a window in an office room depending on the wide-ranging outdoor temperature is conducted in the MATLAB tool Simulink. The air temperature and air velocity are assumed according to the standards, and the MRT is simulated. The angle factors, U-value of walls/windows, occupant position, occupant posture, and outdoor temperature are the critical parameters that affect MRT. The results show varied responses from MRT for each of the five outdoor temperature scenarios simulated for three types of exterior walls. Seated occupants have equal MRT, whereas standing occupants have minor discrepancies when exposed to a window at the same distance in all outdoor scenarios. When the placement of occupants is not equally exposed to the window, the seated occupants have a higher MRT difference than the standing occupants. [ABSTRACT FROM AUTHOR]

Indoor air temperature belongs to the most important climatic variables in indoor climate research, affecting thermal comfort, energy balance, and air movement in buildings. This paper focuses on measurement errors when using thermocouples in indoor temperature measurements, with special attention on measurements of air temperature. We briefly discuss errors in thermocouple measurements, noting that, for temperatures restricted to indoor temperature ranges, a thermocouple Type T performs much better than stated in "standards". When thermocouples are described in the literature, industrial applications are primarily considered, involving temperatures up to several hundred degrees and with moderate demands on accuracy. In indoor applications, the temperature difference between the measuring and the reference junction is often only a few degrees. Thus, the error contribution from the thermocouple itself is almost immeasurable, while the dominant error source is in the internal reference temperature compensation in the measuring instrument. It was shown that using an external reference junction can decrease the measurement error substantially (i.e., down to a few hundredths of a degree) in room temperature measurements. One example of how such a device may be assembled is provided. A special application of room temperature measurements involves measuring indoor air temperature. Here, errors, due to radiation influence on the sensor from surrounding surfaces, were surprisingly high. The means to estimate the radiative influence on typical thermocouples are presented, along with suggestions for modification of thermocouple sensors to lower the radiation impact and thereby improve the measurement accuracy. [ABSTRACT FROM AUTHOR]

This paper investigates adaptive thermal comfort during summer in medical residences that are located in the French city of Troyes and managed by the Association of Parents of Disabled Children (APEI). Thermal comfort in these buildings is evaluated using subjective measurements and objective physical parameters. The thermal sensations of respondents were determined by questionnaires, while thermal comfort was estimated using the predicted mean vote (PMV) model. Indoor environmental parameters (relative humidity, mean radiant temperature, air temperature, and air velocity) were measured using a thermal environment sensor during the summer period in July and August 2018. A good correlation was found between operative temperature, mean radiant temperature, and PMV. The neutral temperature was determined by linear regression analysis of the operative temperature and Fanger's PMV model. The obtained neutral temperature is 23.7 °C. Based on the datasets and questionnaires, the adaptive coefficient α representing patients' capacity to adapt to heat was found to be 1.261. A strong correlation was also observed between the sequential thermal index n (t) and the adaptive temperature. Finally, a new empirical model of adaptive temperature was developed using the data collected from a longitudinal survey in four residential buildings of APEI in summer, and the obtained adaptive temperature is 25.0 °C with upper and lower limits of 24.7 °C and 25.4 °C. [ABSTRACT FROM AUTHOR]