Search

Photovoltaic modules are impacted by overheating, which degrades their conversion efficiency and shortens their lifespan. This work attempts to study the cooling potential for a hybrid photovoltaic/thermal (PV/T) system by employing CuO and Fe2O3 nanofluids with 0.2% and 0.3% volume fractions (φ), circulated in a heat exchanger attached at the rear side of the PV module to lower the temperature of the PV cells and improve its energy and exergy efficiencies. Consequently, a 2D numerical model was analysed given the energy balance across the PV/T system layers, which is evaluated in line with measured experimental data. The results indicate that the successfully synthesised nanomaterials could improve the performance of the nanofluids and increase the heat exchange between PV/T system layers, reducing the PV cells’ temperature by 23.49% and 34.58% when cooling by CuO and Fe2O3 nanofluids at φ=0.3%. Compared to the uncooled PV module, the electrical efficiency has increased by 9.21% and 10.30%, while thermal efficiency increased by 38.9% and 43.3% under cooling with CuO and Fe2O3 nanofluids, respectively. Thereby, the exergy destruction (exergy losses) and entropy generation have decreased by about 26% and 68% when cooling with Fe2O3 nanofluid, which improved the exergy efficiency by 13% more than CuO nanofluid.

Recently, photovoltaic technology applications have occupied a wide range in electric generation. The temperature rising higher than the operating temperature permissible is the weak point facing this technology, which significantly influences the performance of the photovoltaic cells. Using nanofluids as the coolant of photovoltaic (PV) modules is an effective method, circulating nanofluids in the heat exchanger attached to the backside of the PV module to absorb excess heat and enhance the performance of the PV module. The current work investigates using zirconium oxide (ZrO 2) nanofluid as a coolant at different volume concentrations (0.015 vol%, 0.025 vol%, 0.0275 vol%) in deionized (DI) water to reduce the temperature of the photovoltaic PV cells and then analyses the performance from the energy/exergy viewpoints. The results indicate that the PV module temperature was reduced by 10.2 °C when cooled by ZrO 2 nanofluid at 0.0275% volume concentration in DI water compared to the reference PV module, resulting in remarkable system energy and exergy enhancement. Besides, the cooling by DI water has decreased the PV module temperature by 5.1 °C. The overall efficiencies gradually increment with an increase in volume concentration by 8.9%, 18.8 % and 24.4%, respectively, compared with PV modules cooled by DI water. Using ZrO 2 nanofluids with 0.0275 vol% could enhance the exergy efficiency by 66.8% and reduce the exergy losses and entropy generation by 7% and 26%, respectively.

In order to address the limitation of low flux in ultrafiltration (UF), a suitable additive is introduced into the base polymer to modify the membrane morphology, thereby enhancing flux rates. In this study, chamomile leaf nanoparticles (Chm NPs) were investigated as a novel green material for utilizing in UF membrane synthesizes. To enhance comprehension of the influence of Chm on the synthesis of PES UF membranes, a series of membranes were fabricated by including different quantities of Chm into the casting solution; (0, 0.5, 1.5, and 2 wt. %.). The synthesized membranes were fully characterized, through the porosity, pore size, hydrophilicity, membrane morphology, and UF efficiency. Manufactured PES/Chm membranes demonstrated significantly increased permeate water flux (PWF) (up to 498 kg/m2 h), which was four times that of the pristine PES membrane (116 kg/m2 h), besides that the bovine serum albumin (BSA) and Congo red dye (CR) rejection of PES/Chm membranes was still kept high. The enhanced PWF was mostly due to the more porous membrane structure and increased hydrophilicity. Meanwhile, the higher surface hydrophilicity of the PES/Chm membranes resulted in greater antifouling performance and the high flux recovery ratio (FRR) of 93 %. Based on the results of this research, the Chm may be used as a novel green additive with substantial application potential in the fabrication of UF membranes wastewater treatment.

The energy and exergy efficiency of a photovoltaic thermal (PV/T) system at various volume fractions is investigated with mono TiO2 nanofluid and new hybrid TiO2–Fe2O3 nanofluid. Serpentine tubes soldered on an absorbing plate attached to the rear of the PV module have been proposed to evaluate the effect of nanofluids on the PV/T temperature reduction, energy produced, and exergy losses. The study compared energy and exergy with previous studies and delivered an economic analysis to confirm the feasibility of applying nanofluids. The results indicated that using TiO2–Fe2O3 nanofluid reduced the PV cell's temperature by 42.19% compared to water, TiO2 nanofluid, which increased the electrical power by 74.5% and 46.22% when cooling by mono and hybrid nanofluid at 0.3 vol%. The PV/T system's maximum thermal and electrical efficiency recorded with mono and hybrid nanofluids was 34.6%, 8.44%, 47.2%, and 12.62%, respectively. Dispersion of hybrid nanocomposite in DI water has enhanced the Nu number and HTC by 42.72% and 23% higher than mono nanofluid, which improved the exergy efficiency of the PV/T system by 14.89%. A better payback period was achieved with a hybrid nanofluid by 54 days with reduced exergy losses by 45.5% and entropy generation by 86.29%.

This study aims to optimize operating parameters of the effect of embedded silica nanoparticles (SiO2 NPs) and modified silica NPs with polyethylenimine (PEI) (SiO2-g-PEI NPs) into polyethersulfone (PES) to fabricate a mixed matrix membranes (MMMs) for pharmaceutical wastewater treatment. The performance of modified MMMs was compared in the separation of Mebeverine hydrochloride (MBV) from aqueous pharmaceutical wastewater. In order to produce a particular quantity of flux and rejection above desired levels, an optimization technique was used to find the best values for various important process parameters. To enhance the effectiveness on a bigger scale, response surface methodology (RSM) and analysis of variance (ANOVA) were utilized as mathematical and statistical approaches. This study examined the effects of operational parameters on the PES-NPs membranes permeate flux and MBV rejection for each sample. These parameters included SiO2/or SiO2-g-PEI NPs content (0.7–1 wt %), solution feed pH values (4-10), and MBV concentration (10–100 ppm). A mathematical model to calculate the permeate flux and rejection (%) was established. The results showed that the SiO2 MMMs had the best performance of 38.27 LMH permeate flux and 81.26% of MBV rejection, while the permeate flux and MBV rejection % for SiO2-g-PEI MMMs were 104.11LMH and 99.00%. The SiO2 wt % of 0.8447%, MBV concentration of 98.18 ppm, and pH of 4 were the optimal parameters for the SiO2 MMMs, while the optimal parameters for SiO2-g-PEI MMMs were SiO2-g-PEI wt. % of 0.93%, MBV concentration of 22.7 ppm, and pH of 4.79 for eliciting the optimum response.

Overheating of photovoltaic (PV) cell is one of the most common issues that cause the degradation of their function and reduce conversion efficiency. This work investigates the effect of using a novel TiO2-CuO hybrid nanofluid to improve the energy and exergy of photovoltaic thermal (PVT) systems by reducing PV cell temperature. Serpentine tubes soldered on an absorbing plate attached behind the PV module were proposed to improve heat removal of the PV module with volume concentrations of 0.2 vol% and 0.3 vol%, with a flow rate of 1.16 L/min. Improving the thermophysical properties of the hybrid nanofluid has reduced the temperature of the PV module by 39% more than the uncooled PV module. The PVT system's electrical power and overall efficiency improved by 77.5% and 58.2%, respectively, at increased volume concentration to 0.3 vol% compared with the uncooled PV module. The exergy analysis indicated an increase in the overall exergy efficiency by 14.97 %, with thermal exergy dropping because of the closer the outlet nanofluid temperature to ambient temperature. Hybrid nanofluid cooling has improved exergy efficiency to 14.97%, reducing exergy losses by 37.9% and entropy generation by 69.6% at 0.3 vol%. The economic analysis shows a better payback period of 21 months when cooling with a hybrid nanofluid compared with the uncooled PV module.

Development and application of hybrid membranes containing multi-component materials are increasing day by day in the fields of environmental protection and water treatment. In this research, the efficiency of titania nanowire (TiO2 NW)-based self-supported hybrid membranes was investigated in the removal of Escherichia coli (E. coli) bacteria and MS2 bacteriophages from contaminated water mimicking the microorganism suspension. Furthermore, toxicology tests on the as-prepared membranes were also performed. TiO2 NWs were coated with iron(III) oxide (Fe2O3) and copper(II) oxide (CuO) nanoparticles, respectively, and cellulose was used as reinforcement material. It was found that, the functionalisation strongly affected the MS2 removal ability of as-prepared membranes, which can be due to the electrostatic interactions between the surface of hybrid membrane and the bacteriophages. The most efficient removal (greater than or equal to 99.99%) was obtained with the TiO2 NW-CuO-cellulose membrane at pH 7.0. The fabricated hybrid membranes were characterized by micro computed tomography (μCT), Raman spectroscopy, Fourier transform infrared spectroscopy (FT-IR), dynamic light scattering (DLS), contact angle measurement and inductively coupled optical emission spectrometry (ICP-OES) techniques. This study shows a simple route of the usage of novel and effective inorganic nanowire-based hybrid membranes for bacteria and virus removal, providing new pathways in the field of water filtration technologies.

Copyright of Iraqi Journal of Desert Studies is the property of Republic of Iraq Ministry of Higher Education & Scientific Research (MOHESR) and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The temperature rising of the photovoltaic (PV) modules is a major issue leading to a reduction in their conversion efficiency and low output power. Therefore, removing heat from the PV module is necessary to permanently work and improve the electrical power output. Serpentine pipes and a thermal absorber plate has proposed with fluid circulation to reduce the PV cell temperature and improve their efficiency. The current work experimentally investigates the effect of using tungsten trioxide (WO3) nanofluids on the PVT system's energy and exergy efficiency at different volume concentrations of 0. 5 vol%, 0. 75 vol%, and 1 vol%. The results indicated an increment in the electrical power output by 11.15 W due to reducing the PV temperature by 21.4% and enhancing the PVT overall efficiency by 29.6% compared with the cooling by Deionized (DI) water. Increasing the volume concentration of nanoparticles increased the Reynolds number, and the Nusselt number enhanced the heat transfer coefficient and increased the pressure drop. Improving the thermal properties of the nanofluid has increased the electrical exergy efficiency and lowered the thermal exergy efficiency due to the reduction in thermal exergy quality. Compared to DI water cooling, exergy losses and entropy generation were reduced by 10% and 34.8%, respectively.

In this study, Zr-pillared montmorillonite clays (Zr-PILCs) were synthesized using two different precursor materials: raw montmorillonite (CM) and sodium ion-saturated montmorillonite (Na-CM) at different Zr/clay ratios (2.5, 5 and 10 mmol/g). To study the effect of Zr concentration and clay pre-treatment with NaCl on pillaring, the modified clay samples were characterized in detail using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), high-resolution transmission electron microscopy (HRTEM), scanning transmission electron microscopy and energy-dispersive X-ray spectroscopy (STEM-EDX). The XRD analysis showed the increase of basal spacing of Zr-PILCs prepared from both precursor materials: from 1.26 to 1.74 nm in the case of CM, and from 1.13 to 1.93 nm for Na-CM. Results from FT-IR revealed new bands ascribed to Zr-O bonds in the range of 400–500 cm−1 in Zr-pillared samples obtained from Na-CM at Zr/clay ratios of 2.5 and 5 mmol/g. The distribution and nature of Zr species in between the silicate layers were studied using STEM-EDX and HAADF imaging. They were found to be separated by a distance of 1.5–3 nm and their thickness lies in the range of 1–2 nm. Pillared clays prepared from pre-treatment with NaCl were more thermally stable at higher temperatures.

In this study tungsten oxide and graphene oxide (GO-WO2.89) were successfully combined using the ultra-sonication method and embedded with polyphenylsulfone (PPSU) to prepare novel low-fouling membranes for ultrafiltration applications. The properties of the modified membranes and performance were investigated using Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), contact angle (CA), water permeation flux, and bovine serum albumin (BSA) rejection. It was found that the modified PPSU membrane fabricated from 0.1 wt.% of GO-WO2.89 possessed the best characteristics, with a 40.82° contact angle and 92.94% porosity. The permeation flux of the best membrane was the highest. The pure water permeation flux of the best membrane showcased 636.01 L·m−2·h−1 with 82.86% BSA rejection. Moreover, the membranes (MR-2 and MR-P2) manifested a higher flux recovery ratio (FRR %) of 92.66 and 87.06%, respectively, and were less prone to BSA solution fouling. The antibacterial performance of the GO-WO2.89 composite was very positive with three different concentrations, observed via the bacteria count method. These results significantly overtake those observed by neat PPSU membranes and offer a promising potential of GO-WO2.89 on activity membrane performance.

The emergence of mixed matrix membranes (MMMs) or nanocomposite membranes embedded with inorganic nanoparticles (NPs) has opened up a possibility for developing different polymeric membranes with improved physicochemical properties, mechanical properties and performance for resolving environmental and energy-effective water purification. This paper presents an overview of the effects of different hydrophilic nanomaterials, including mineral nanomaterials (e.g., silicon dioxide (SiO2) and zeolite), metals oxide (e.g., copper oxide (CuO), zirconium dioxide (ZrO2), zinc oxide (ZnO), antimony tin oxide (ATO), iron (III) oxide (Fe2O3) and tungsten oxide (WOX)), two-dimensional transition (e.g., MXene), metal–organic framework (MOFs), covalent organic frameworks (COFs) and carbon-based nanomaterials (such as carbon nanotubes and graphene oxide (GO)). The influence of these nanoparticles on the surface and structural changes in the membrane is thoroughly discussed, in addition to the performance efficiency and antifouling resistance of the developed membranes. Recently, GO has shown a considerable capacity in wastewater treatment. This is due to its nanometer-sized holes, ultrathin layer and light and sturdy nature. Therefore, we discuss the effect of the addition of hydrophilic GO in neat form or hyper with other nanoparticles on the properties of different polymeric membranes. A hybrid composite of various NPs has a distinctive style and high-quality products can be designed to allow membrane technology to grow and develop. Hybrid composite NPs could be used on a large scale in the future due to their superior mechanical qualities. A summary and future prospects are offered based on the current discoveries in the field of mixed matrix membranes. This review presents the current progress of mixed matrix membranes, the challenges that affect membrane performance and recent applications for wastewater treatment systems.

Novel hybrid structures have attracted attention in several instances of scientific research and different technological applications in this decade due to their novel characteristics and wide range of applicability. Hybrid membranes with multiple components (three or more) are also increasingly used in water purification applications, and their ease of handling and reusability make them a promising candidate for the degradation of organic pollutants by photocatalysis. In this study, the preparation and characterization of tungsten trioxide nanowire (WO3 NW)-based hybrid membrane structures are reported. Furthermore, the adsorption properties and photocatalytic efficiency of the as-prepared membranes against methylene blue (MB) organic dye under UV irradiation is also presented. Characterization techniques, such as scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray powder diffraction (XRD) are performed to study the morphology and surface of the as-prepared hybrid membranes. The removal efficiency of the hybrid membranes against MB is 77% in a 120 min decomposition reaction. The enhanced value can be attributed to the hybrid structure of the membrane that enhances not only the adsorption capability, but also the photocatalytic performance. Based on the results obtained, it is hoped that hybrid membrane technology could be a promising candidate for future photocatalysis-based water treatment applications.