Search

Featured Application: This study represents a breakthrough in the engineering of turning processes for manufacturing. By examining dynamic properties and vibration response during turning, it provides key insights for real-time machining system monitoring. The findings can improve surface quality and stability, particularly for slender, flexible shafts. Industries such as automotive, aerospace, and heavy equipment manufacturing can leverage these insights to optimize machine performance, reduce downtime, and boost productivity. This marks a significant stride towards more efficient manufacturing. The chatter that occurs during the turning operation, especially when cutting a slender and flexible shaft, determines the surface quality of the workpiece and the stability of the machining system. However, when building a dynamic model of a slender workpiece with a chuck and tailstock, it is generally regarded as a cantilever or simply supported beam, without consideration of the axial force and supported stiffness effect. In this work, a dynamic model for thin and flexible workpieces with different clamping boundary conditions was first built. Then, a finite element analysis (FEA) was used to study the influence of the axial force and supporting stiffness on the mode frequencies of the workpiece. A further analysis found that the relationship between support stiffness, axial force, and the dynamic response of the workpiece is nonlinear and far more complex than that of the simply supported beam model. The clamping force directly influenced the magnitude of the vibration response with the decrease of shaft stiffness during the turning process. These results were verified experimentally by measuring the vibrational response of slender shafts with different clamping modes using an on-rotor sensing (ORS) system. It proved that the proposed model shows advantages for the identification of dynamic vibration and quality control when machining slender workpieces. [ABSTRACT FROM AUTHOR]

Wear is one of the most common failures of hydrodynamic bearings. The main purpose of the present work was to investigate the effects of wear on lubrication performance and acquire efficient vibration signatures for fault diagnosis. In this paper, a finite element model (FEM) for a two-disk rotor supported on worn hydrodynamic bearings is presented in which the oil film force is evaluated by linear and nonlinear models. Numerical and experimental results indicate that the static and dynamic characteristics of the bearing are significantly changed by wear, leading to a drop in system critical speeds due to the deterioration of the constraint status provided by the bearings to the rotor. As the wear depth increases, the onset speed of oil whirl increases, while that of oil whip becomes lower, and large amplitudes of resonance and oil whip are more likely to be excited. More notably, all of the above vibration signatures in the y-direction are more sensitive to wear compared to those in the x-direction, which means that wear faults can be diagnosed by differences in vibration characteristics between the x- and y-directions. This research can provide a theoretical foundation and engineering guidance for the hydrodynamic bearing wear fault diagnosis. [ABSTRACT FROM AUTHOR]

Grinding residual stress (GRS) has been understood to have a great impact on the strength of gear fatigue life. However, there are lack of detailed studies on the influences in terms of mechanism and magnitude. To fill this gap, this study proposed a new method based on finite element analysis (FEA) to calculate the overall meshing stress on a gear tooth surface by including both the GRS and elastohydrodynamic lubrication (EHL) film pressure. Applying this method to a spiral bevel gear has resulted in a number of interesting results that GRS produced to reveal its mechanism of action through a full meshing cycle. The acquired understanding would be useful for development of manufacturing processes. [ABSTRACT FROM AUTHOR]

[Display omitted] • Mesh stiffness model of opening-crack tooth with elastoplastic deflection is built. • The model can accurately estimate the mesh stiffness of gears with crack failure. • Impacts of failure severity on the mesh stiffness and load sharing are analyzed. • Tooth deflection affects mesh stiffness, load sharing and meshing zone ratio. In the gear transmission system, tooth root crack often occurs due to the impact of machining technology and cyclic load. The appearance of tooth root cracks will affect its mesh stiffness and change the vibration characteristics of the system, thereby reducing system reliability and service life. In previous studies on the modeling of the mesh stiffness of cracked gears, the cracks were often supposed to be in a closed state, and the elastoplastic deflection of the fault gear teeth was also neglected, resulting in significant errors in the estimation of the mesh stiffness. When a tooth root crack occurs, the engaged gear teeth will deviate from the theoretical meshing position due to the elastoplastic deflection of the fault tooth. Therefore, an accurate mesh stiffness estimation model in view of the opening crack and elastoplastic deflection of the cracked tooth is put forward in this study. Firstly, the actual meshing position of the tooth pairs is derived considering the elastoplastic deformation in the crack opening state; Then, the improved potential energy method is adopted to calculate the mesh stiffness, and the finite element method (FEM) is applied to verify it. At last, the influence of failure severity and elastoplastic deflection degree on mesh stiffness and load sharing is analyzed. The results show that the severity of the crack failure and elastoplastic deflection has a significant impact on the mesh stiffness and load-bearing. This research can provide stiffness input for the study of fault dynamics of the gear transmission system. [ABSTRACT FROM AUTHOR]