Search

This paper proposes a systematic method for the identification of the load circuit parameters (say the $\boldsymbol{R}$ , $\boldsymbol{L}$ , and $\boldsymbol{C}$ elements) based only on the information of the instantaneous voltage and current measured at the point of common coupling (pcc). Geometric Algebra (GA) and concepts of differential geometry are used to produce a rigorous mathematical framework. The identification is formulated as a multidimensional geometrical problem that is solved conveniently by means of GA. Once the passive elements of the load have been identified, the active and reactive powers can be computed from first electromagnetic principles (Maxwell Equations). The theory is general and is verified with linear and nonlinear circuits. The paper shows single-phase circuits but the theory can be extended to three-phase circuits. The method is easy to program and has shown to be very robust for all tested cases. Because of its generality, the method presented will find applications beyond electric circuits. [ABSTRACT FROM AUTHOR]

Titanium tetrachloride (TiCl4) is a well-known source of titanium (Ti) for the formation of titanium nitride (TiN) barrier material in the semiconductor interconnection process; however, the reaction of by-products with airborne molecules can cause unexpected pump trips and equipment breakdown from the by-product powder build-up. Plasma scrubbers are used to decompose by-products, but hydrogen chloride (HCl) and nitrogen oxides are produced during and after the process. The process mechanisms change when the temperature and applied power of the heat source change. In this paper, we study the influence of the reactor temperature and applied power to the heat source on the decomposition capacity of TiCl4 in a plasma pretreatment system (PPS). We examine the effect of the temperature and heat source power to understand the reaction mechanisms for the composition and decomposition of gaseous species with chemical reactions through simultaneous methods. We analyzed the system with computational fluid dynamics (CFD) and chemical kinetic simulation to investigate the changes of the system mechanism. Subsequently, we achieved results for the correlation between the temperature of the reactor, power applied to the heat source, composition and decomposition of species, and chemical reaction mechanisms. [ABSTRACT FROM AUTHOR]

This article analyzes the problem of modeling the properties of such magnetic elements as inductors, coupled inductors, and transformers using the SPICE software (version 17.2). Both the classical models of magnetic elements, built in this software, and the models implemented in the form of subcircuits are described. In particular, attention was paid to the possibility of taking into account the non-linearity of the characteristics of the considered elements and mutual couplings between electrical, magnetic, and thermal quantities. Using the results of thermographic measurements, the need to take into account the differences in temperature values between the individual windings and the core of inductors and transformers was justified. Selected models of the considered elements given in the literature are briefly characterized. The network structures of the electrothermal models of the considered elements elaborated at Gdynia Maritime University are presented. The results of calculations and measurements illustrating the correctness of the described models and their prac-tical usefulness for the elements of different structures are presented and discussed. [ABSTRACT FROM AUTHOR]

One of the early design decisions for DC‐DC converters is the choice of an appropriate magnetic core material. Powder cores in particular are suitable due to their saturation flux density of up to 1.5 T. However, high DC currents constitutes a significant problem since the winding cross‐section rises with the current, which consequently increases AC losses due to skin effects. Another challenge is the reduction of winding layers to decrease proximity losses. This paper presents an improved single‐layer winding design procedure for DC‐DC converter powder cores. The procedure determines the optimum number of parallel cores and stacks. This way, the procedure enables a predefined maximum wire cross‐section for copper loss optimisation and single‐layer winding. The introduced approach defines the optimum switching frequency as a trade‐off between core loss and core volume. Finally, experimental tests with two setups validate 27 kW DC‐DC converters and hence the design procedure using Si‐IGBTs and SiC‐MOSFETs. The results demonstrate that SiC‐MOSFETs reduce core volume by a factor of 3 compared to Si‐IGBTs. Further, the SiC setup reaches high efficiencies of up to 98.53% compared to 98.17% for the Si‐based converter. [ABSTRACT FROM AUTHOR]

This paper proposes an adaptive self-tuned current controller design for an LCL-filtered LC-tuned single-phase shunt hybrid active power filter (HAPF), which offers adaptability and flexibility of the control system to filter parameters changes. System modelling and online identification of parameters are presented. Then, a systematic self-tuned controller (STC) design is proposed to calculate the controller parameters and obtain the final control law adaptively. The exact HAPF parameters design is described and the overall closed-loop stability evaluation with considering digital control delay is discussed in this paper. To confirm the theoretical achievements, simulations and experimental tests on a real prototype system are performed. The results are in good accordance and demonstrate the effectiveness and superior performance of the suggested control technique. Furthermore, a comprehensive comparison between the proposed control technique and other controllers is provided to show the superiority of the proposed system from different aspects. [ABSTRACT FROM AUTHOR]

In renewable energy micro-source applications, a wide range of voltage conversion of the step-up converter is an essential part to equalize the typical low voltage of micro-source with DC-bus voltage of Inverter or motor drives. In order to meet this purpose, an ultra-voltage gain step-up DC-DC converter is proposed in this paper. The proposed converter has made an arrangement of the regenerative-boost fed switched inductor and capacitor configurations. Thereby, due to such an organization of structure, the proposed converter can develop an extremely high voltage-gain even at lower duty ratios. In addition, it has the advantage of lower switching stress across all power semi-conductive diodes. Furthermore, this paper describes the steady-state analysis and comparative features of the converter with existing recent literature. Finally, to validate theoretical analysis and test the feasibility and suitability of the proposed ultra-gain converter, the experimental results were observed by a 500 W fabricated prototype. [ABSTRACT FROM AUTHOR]

This paper analyzes the unsymmetrical operation of the dc/dc MMC caused by parametric uncertainty. The unsymmetrical operation is referred to as the condition in which parameters involved in ac power generation are not equal in the phase-legs of the converter. Because existing models in the literature cannot exhibit the unsymmetrical operation of the dc/dc MMC, new detailed and simplified steady-state models are developed in this paper. In the developed models, the connection between the operation of different phase-legs shows itself when the dc-link impedance is considered. Using the developed models, the parameters that can force the converter to operate in unsymmetrical conditions are identified, and the maximum variation that the converter can tolerate is found. It is shown that even a small parameter variation leads to the leakage of the ac circulating current into the dc-link, which is not acceptable. By conducting various case studies, the impacts of the dc-link length, the transmitted power, and the conversion ratio on the unsymmetrical operation of the dc/dc MMC are characterized. The results showed that the converter would be more sensitive to the parameter variation as these parameters increase. Comparative analysis and simulation results confirm the validity and effectiveness of the presented models and analysis method. [ABSTRACT FROM AUTHOR]

Aiming at the fault traveling wave on the LCC-MMC HVDC transmission line, this paper analyzed its reflection and refraction characteristics at the DC buses and the fault point, plotted its propagation grid diagrams, obtained the relationship between the polarity of fault traveling wave and the boundary elements, and drew the conclusion that when the impedance of DC filter is far less than the wave impedance of transmission line, the existing fault location methods that need to distinguish these two waves according to their polarities are not applicable to the LCC-MMC HVDC system. On these bases, this paper proposed a modal traveling wave arrival time difference-based location principle for pole-to-ground fault, and a fault traveling wave propagation path ratio-based location principle for pole-to-pole fault, these principles neither need to identify the wave polarity, nor need the wave velocity value. In order to better extract the wave heads and their arrival time, this paper pre-treated the sampling data to make sure all the wave heads are extracted from the same frequency band, then the wave heads and their arrival time can be extracted with the empirical mode decomposition. The simulation results verified the effectiveness of the proposed fault location principle. [ABSTRACT FROM AUTHOR]

Light-emitting diodes (LEDs) are widely used in street lighting, landscape lighting, liquid crystal display (LCD) backlighting, healthcare, etc. As an important part of LED lighting products, LED driver plays a vital role in maintenance costs reduction, energy saving and lifetime prolongation. In this paper, a single-stage LED driver is proposed, which is integrated by a totem-pole bridgeless power factor correction (PFC) unit and several modular LCL-T resonant rectifiers. The totem-pole bridgeless PFC unit and the LCL-T resonant rectifiers are integrated by sharing switches, which can simplify the circuit and reduce the system cost. The output current can be regulated by applying the variable inductor control. Constant duty cycle and fixed switching frequency operation can be achieved as well. The operating principle and the performance of the proposed converter are analyzed in this paper. In addition, a precise parameter design method is proposed by considering the high-order harmonics. At last, an experimental prototype is established to validate the proposed parameter design and variable inductor control method. [ABSTRACT FROM AUTHOR]

This paper describes experimental verification of single-phase variable inductor prototypes rated at 2.4 kVAr (75 mH, 10 A, 230 V, 24 kg) and 12 kVAr (43 mH, 30 A, 400 V, 78 kg). Results for much smaller devices rated at 1-10 Var are also shown. The variability of inductance of the main AC winding was achieved by adding a DC winding, wound through the apertures placed symmetrically in the core such that both windings were magnetically orthogonal. Local saturation caused by the magnetic field due to DC winding creates virtual air gaps. This method is capable of lowering the main inductance by over 90% if no real air gap is present, but for industrial applications the range of variability is likely to be closer to 20-30% range, depending on the size of the real air gap in the magnetic circuit. The amount of variation/control can be improved by using more than one control winding. Very good repeatability of performance was observed, with relatively small total harmonic distortion introduced due to control. The experimental findings agree with a generalised analytical model. [ABSTRACT FROM AUTHOR]

Negative-sequence current is required to be intentionally injected to support the power grid or compensate the imbalanced load in asymmetrical faults utilizing STATCOM. However, the extreme compensation range of negative-sequence current injection becomes complicated when grid voltage becomes asymmetrical. This article presents a novel off-line strategy for negative-sequence current compensation under two typical kinds of asymmetrical grid faults — single-phase voltage drop and double-phase voltage drop, with the following two benefits simultaneously: maximizing negative current compensation capacity; avoiding iterations and reducing computation burdens. In this paper, the mechanism of DC voltage balancing among three phases in STATCOM is analyzed and a new identification method of negative-sequence current compensation range is explored out. To simplify the calculation, this paper takes the ratio of negative-sequence reactive (Iq-) and active (Id-) current as a variable (s). In this way, the relationship between the extreme compensation range, asymmetrical voltage sag depth of power grid h is drawn with MATLAB. Different from the previous iterative method, the off-line identification method is applied to avoid huge iterations. By fitting the curve, the precise ranges of negative-sequence current compensation under different asymmetrical grid faults are approximated as simple polynomials, thus significantly reducing the computation burdens. Simulation and experimental results verify the practicability of the proposed compensation method. [ABSTRACT FROM AUTHOR]

A DC system saturated core fault current limiter (DCSFCL) was proposed to limit the fast rising trend of fault current in HVDC system. However, traditional method to calculate and design the DCSFCL tend to neglect leakage flux around the permanent magnet (PM), leading to large calculation error and inappropriate design procedure. The novel contribution of this paper is that it proposed a modularization method to analyze the permeance of both PM and adjacent air. Hence, the leakage flux effect is considered properly and a more accurate permeance matrix can be derived in a pure mathematical way. In this case, DCSFCL can be calculated much faster than the FEA simulation program with a promising accuracy regarding fault limiting performance. More importantly, design flow of the DCSFCL and related PM biased devices was given as well. Calculation result shows that inductance value calculated by the proposed method has less than 1% error compared with fine meshed FEA simulation result and about 20% increase in accuracy compared with traditional method that neglects PM leakage flux effect. Prototype of the DCSFCL was also built and experimental tests were carried out to verify the correctness of the proposed method. [ABSTRACT FROM AUTHOR]

The dc-dc converters with high step-up DC-voltage gain play a vital role in integrating low voltage DC sources. Though several converter topologies are reported in the recent past, attempts have been made to reduce the components, especially the switching devices, passive elements, converter losses, etc., of the converter. A novel DC-DC converter topology, viz., single switched impedance network (SSIN)-based converter with n-stage is proposed in this paper. The operation of the SSIN based converter in continuous and discontinuous conduction modes are discussed. The effect of parasitic elements on DC-voltage gain and efficiency of the SSIN is carried out. The small-signal model of the SSIN converter is derived. The performance of the SSIN converter is compared with the similar converter topologies. The 500 W prototypes of the SSIN with n = 1 and n = 2 are fabricated, and the experimental results are presented in this paper. To improve the converter performance, SiC-based semiconductor devices are used. The SSIN converter with two-stage has low switch loss at 500 W load, improved efficiency during high power and high output voltage operation, the switch stress of Vo/2, etc. [ABSTRACT FROM AUTHOR]

When a fault occurs on the dc side of the voltage source converter based high voltage direct current (VSC-HVDC) transmission system, the fault current rises quickly due to the low damping of the dc system. Using a dc fault current limiter (DC-FCL) to limit the rise of the fault current can significantly reduce the breaking requirements of the DCCB. A topology of a bidirectional active dc fault current limiter (BA-FCL) based on coupled inductor is proposed in this paper. No expensive full-controlled power electronic devices are used in this topology. Only a few half-controlled power electronic devices are used to achieve active control of the current limiting unit. Compared with many topologies of current limiter at present, the fault current limiting effect of BA-FCL is improved significantly while the cost, volume, topology complexity, and control complexity are reduced. The stress analysis and parameter design of the proposed current limiter are carried out. Finally, the simulation case study and hardware experiment are implemented to verify the good economy and current limiting performance of the proposed topology. [ABSTRACT FROM AUTHOR]

The current-limiting inductors (CLIs) are commonly used to suppress DC fault current to safely trip DC circuit breakers in MMC-HVDC systems, but it significantly jeopardizes DC dynamics and causes instantaneous power mismatch between AC and DC sides of islanded rectifier station (RS), exposing MMC internal states to large disturbance. This paper firstly provides a detailed analysis of the influence of CLIs on AC fault, establishes RS mathematical representation including AC side dynamic, and reveals the mechanism of DC voltage oscillation, modulation saturation and PCC waveform distortion. The analysis shows that the AC and DC fault characteristics are decoupled under unsaturated AC modulation, but coupled under excessively low submodule capacitor voltage, where AC modulation is saturated and PCC waveforms are distorted. To solve this issue, a novel RS AC fault ride through method for MMC-HVDC system with CLIs is proposed to stabilize RS DC voltage, desaturate AC modulation and decouple fault characteristics by regulating the zero-sequence modulation of circulating current suppression. In addition, a current reference disturbance and an AC energy dissipation device coordinated control are designed, which adaptively recovers the submodule capacitor voltage. Finally, the feasibility of the proposed method is verified by simulation results. [ABSTRACT FROM AUTHOR]

Electromagnetic Transient (EMT) simulation tools are typically developed using conventional procedural programming languages. On the other hand, modern high-level and equation-based programming languages, such as Modelica, are currently available. Modelica allows formulating models that are easy to develop, maintain and understand by expressing what needs to be computed without stating how it should be computed. This paper presents a Modelica-based simulator for electromagnetic transients. It is demonstrated that this approach offers significant advantages for developing sophisticated models. Computational performance and accuracy are compared to a conventional EMT-type simulation tool. [ABSTRACT FROM AUTHOR]

The mainstream production of optoelectronic and electronic devices based on epitaxial III-V compound semiconductor materials largely employs metalorganic vapor phase epitaxy, a process first demonstrated for devices in the 1970’s. For this special issue in honor of Prof. P. Daniel Dapkus, this paper first briefly reviews his early contributions that spearheaded the interest of MOVPE as a III-V device epitaxy process. Next, the paper discusses MOVPE reactor development in the 1980’s, which at the time was one of the key challenges in establishing MOVPE technology as a reliable epitaxy manufacturing process. The approach combined physical modeling and numerical simulations of reactor processes followed by materials and device demonstrations. Highly uniform performance metrics of AlGaAs/AlGaAs quantum-well diode lasers and two-dimensional monolithic surface-emitting lasers were demonstrated with excellent run-to-run reproducibility. This foundational approach advanced efforts to standardize reactors and subsequent scaling for high-throughput production. [ABSTRACT FROM AUTHOR]

Planning of biorefinery operations is complicated by the stochastic nature of physical and chemical characteristics of biomass feedstock, such as, moisture level and carbohydrate content. Biomass characteristics affect the performance of the equipment which feed the reactor and the efficiency of the conversion process in a biorefinery. We propose a stochastic optimization model to identify a blend of feedstocks, inventory levels, and operating conditions of equipment to ensure a continuous flowing of biomass to the reactor while meeting the requirements of the biochemical conversion process. We propose a sample average approximation (SAA) of the model, and develop an efficient algorithm to solve the SAA model. A feedstock preprocessing process consists of two-stage grinding and pelleting is used to develop a case study. Extensive numerical analysis are conducted which lead to a number of observations. Our main observation is that sequencing bales based on moisture level and carbohydrate content leads to robust solutions that improve processing time and processing rate of the reactor. We provide a number of managerial insights that facilitate the implementation of the model proposed. Note to Practitioners—This paper is motivated by the challenges faced in the bioenergy industry. The focus of this paper is on plants which use the biochemical conversion process to generate liquid fuels. It has been observed that variations in biomass characteristics, such as moisture content, cause variations in feeding of the system which lead to under-utilization of equipment. A requirement of biochemical conversion process is to maintain the carbohydrate content of biomass processed by the reactor, larger than a threshold. We propose a model that identifies the inventory levels and operating conditions of equipment to ensure a continuous flowing of biomass to the reactor. The goal is to improve equipment utilization while satisfying the requirements of the conversion process. The model is tested using real-life data. We found out that by sequencing bales based on moisture level and carbohydrate content, a plant can reduce variability in the system leading to improved system reliability, higher processing rates of the reactor, and higher throughput. [ABSTRACT FROM AUTHOR]

Solid-state transformers (SST) are emerging technologies to replace the conventional low-frequency main transformer (MTR) in railway vehicles. In order to isolate the load side from the AC 25 kV high-voltage (HV) side and to reduce the whole size of the SST, HV insulation and high-frequency transformers should be used in DC/DC converters. Furthermore, due to the severe constraint of installation space and difficulty of heat dissipation management in the bottom of railway vehicles, high-power density and minimum transformer loss should be considered. To satisfy such design requirements of the proposed SST for railway vehicles, high efficiency integrated transformers, which inherently have leakage inductance, are proposed for dual-active-bridge (DAB) converters in this paper. In order to obtain appropriate equivalent leakage inductance for the DAB converters, a calculation methodology for the leakage inductance has been introduced and verified by simulation. Two separated winding structures in the center-core are adopted to improve the core loss, and appropriate winding turns with 60 kV HV insulation capability are selected, according to the proposed design procedure of the integrated transformers. In order to compare the proposed transformers with the conventional transformer having additional inductors and to verify the major characteristics of the transformers, two 125 kW proposed transformers and conventional transformers have been built and evaluated by an 250 kW SST module, operating at 10 kHz switching frequency. Under a 125 kW full-load condition, 99.7% transformer efficiency was obtained by the proposed integrated transformers, which are 4.7% smaller and 7.0% lighter than the conventional transformer. As a result, 26°C maximum temperature improvement has been obtained and 60k V HV insulation capability has been satisfied by the proposed integrated transformers. [ABSTRACT FROM AUTHOR]

This paper introduces a novel frequency domain technique to globally evaluate the accuracy of electro-magnetic transient simulations. It is shown that simulation accuracy at low frequencies can sometimes be poorer than at high frequency. A modified approach which quantifies accuracy from a driving point as a function of frequency is also introduced that uses the Bilinear Transformation and Norton equivalents, to produce a “simulation accuracy spectrum”. This approach can be applied to large systems without explicitly forming state space equations. It also permits the accuracy analysis of networks with distributed components such as frequency dependent transmission lines. Two examples are used to verify the proposed technique, a small network with a frequency dependent transmission line modeled by the universal line model; and the IEEE 39 bus system connected with an LCC-HVdc system. [ABSTRACT FROM AUTHOR]

Summary: High‐frequency characteristics of passive components are crucial to the electromagnetic compatibility (EMC) of an electronic system, and modeling of passive components is of significance for EMC analysis. However, challenges remain in the modeling of passive components with multiple resonant frequencies. In this paper, a method for establishing equivalent models of multi‐resonant frequency passive components, including capacitors, inductors, and resistors, is proposed. Firstly, high‐frequency equivalent circuit topologies of the multi‐resonant frequency passive components, which are simple, easy to understand, and can be applied to the modeling of passive components with various impedance characteristics, are developed. Secondly, a calculation method of equivalent circuit parameters based on least squares and particle swarm optimization (PSO) is presented, which is not sensitive to the initial value, only needs the estimated range of the equivalent circuit parameters, and very suitable for getting the parameters of equivalent circuit models accurately and efficiently. Finally, to validate the method, some SPICE models of single components are established, and a PCB‐level EMC analysis is implemented. The comparisons of the simulated and experimental results show the validity and accuracy of the method. The method is very useful for future components modeling when doing EMC design or other high‐frequency designs. [ABSTRACT FROM AUTHOR]

Dynamic wireless charging (DWC) is one of the most promising and economical power supply solutions for electric vehicles (EVs), which can address range anxiety and downsize the volume of onboard batteries. To solve the null power phenomenon and transfer power pulsation phenomenon in DWC scheme, this paper proposes a new magnetic coupler array to implement continuous charging and reduce the output power variation. The transmitters are placed with a proper interval to eliminate the adjacent coupling and enlarge the coil array’s effective length. ANSYS Maxwell is utilized to demonstrate the finite element analysis (FEA) of the DWC system. A larger receiver coil is designed to significantly mitigate power pulsation and increase the magnetic coupling as the receiver moves along the array. With the well-designed receiver coil, the output power pulsation is $\pm$ 1.52 $\%$. For the high-power capacity scenario, a multilevel connected DC-DC converter is designed on the receiver side to regulate the transfer power. Besides, a passivity-based control (PBC) is developed for the receiving DC-DC converter based on the Euler-Lagrange (EL) model, and a current sharing compensator is employed to balance each phase inductor current. Finally, a 500- $\text{W}$ prototype is constructed, and experimental results are represented to validate the proposed optimized coil array and the proposed PBC method. [ABSTRACT FROM AUTHOR]

In this paper, novel neutral reactor structures are proposed to mitigate the secondary arc current (SAC) in non-conventional Multi-circuit Multi-voltage Transmission lines (MCMVTLs). The parameters of the reactors in the structure are optimized using the Non-dominated Sorting Genetic Algorithm II (NSGA-II). The optimization algorithm, coded in Python, regulates the multiple runs of an Electromagnetic Transients (EMT) simulation program to minimize the secondary arc current. The optimization trials are run in parallel on a 64 core computer to minimize the solution time. A detailed arc model was tested on the EMT program (PSCAD). Using this model and optimized parameters in the proposed neutral reactor schemes, the SAC is indeed extinguished in acceptable times. The SAC and TRV for neutral reactors with optimized parameters are up-to 68 and 77%, respectively, lower than the ones with parameters calculated by the conventional approach which ignores inter-circuit coupling. Meanwhile, the extinction times are up-to 46% faster. As a result, single-phase auto-reclosing in MCMVTLs is viable. [ABSTRACT FROM AUTHOR]

Hybrid energy systems with small modular reactors (SMRs)—a fast-emerging nuclear power plant technology—and renewables hold significant promise for the development of clean energy systems. This paper proposes a simulation model of SMR-based hybrid energy system for electricity and district heating (DH) with a detailed dynamic model of the reactor and a quasi-static model of the DH system in Siemens PTI PSS/E and PSS/Sincal. A multi-timescale approach, separating the load following and frequency regulation operation, is proposed to assess the flexible operation in the presence of highly intermittent renewable energy sources (RESs). A portion of a modified IEEE 30-bus system network is used as a test system for an isolated community to simulate the proposed hybrid energy system, and comparative results demonstrate the potential benefits of the DH system, thermal energy storage, and electrical energy storage to the SMR’s flexible operation. [ABSTRACT FROM AUTHOR]

In High Voltage Direct Current (HVDC) grids, system parameter and/or topology changes following HVDC grid protection actions affect system dynamics and in combination with the existence of line inductors in series with HVDC circuit breakers (DCCB), pose a challenge to designing converter controls that satisfy desired performance and stability requirements. To date, several methods have been proposed for evaluating the influence of the line inductors on system stability; however, tuning of the MMC controls considering system parameter and/or topology changes following HVDC grid protection actions haven’t been studied in detail. This paper presents a systematic tuning procedure for a robust operation of MMCs in any HVDC grid configuration. The proposed method analyzes the impact of variations in HVDC grid system parameters and control bandwidths (BWs) using small-signal based stability analysis and Singular Value Decomposition (SVD)-based performance analysis methods. In addition, it considers the impact of line outages associated with HVDC grid protection actions in order to select optimal control gains that fulfill performance and stability requirements of the HVDC grid for given HVDC Circuit Breakers (DCCBs) line inductor values. To illustrate the proposed methodology, a detailed step-by-step stability analysis in a 4-terminal HVDC grid test system is presented. [ABSTRACT FROM AUTHOR]

The design distance of offshore wind power plants connected through HVAC transmission systems might be extended due to the introduction of mid-cable reactors for reactive power compensation purposes and the latest developments of AC cables for higher voltages. Therefore, the applicability limits between HVAC and HVDC systems must be revised. This paper analyzes the contribution that mid-cable reactive power compensation has on increasing the distance limits of HVAC transmission systems. A methodology is developed to determine an optimal design of such transmission systems. In this methodology, cost of power losses and reactors are minimized for multiple wind speed conditions. As a result, the optimal HVAC voltage level and the optimal number of reactors and their location are determined for different OWPP rated powers and distances. Also, the final transmission system is selected between HVAC and HVDC equivalent configurations based on total costs. [ABSTRACT FROM AUTHOR]

A novel flexible LC-type wind speed sensor, as well as its readout circuit, is proposed in this paper. Two inductors are designed on both surface of the flexible substrate, connecting by a parallel plate capacitor. Hence, substrate bending induced by wind can change the total inductance, then shifting the resonant frequency of this LC-type speed sensor. The readout circuit is designed and realized on the PCB board. The LC-type sensor is tested in the wind tunnel and the readout circuit outputs the frequency spectrum. The experiments demonstrate that the resonant frequency increases with the wind speed up to 25m/s. The measured sensitivity is close to 39.8kHz/(m/s), 50.8kHz/(m/s) and 57.7kHz/(m/s) for the sensor with windward height of 30mm, 40mm and 50mm, respectively. Although large windward height can improve the sensitivity, it’s easy to saturate and the maximum detectable speed is reduced. [ABSTRACT FROM AUTHOR]

LC resonant wireless passive pressure sensor has been receiving increased attention nowadays. In this paper, an innovative LC-C resonant wireless passive pressure sensor based on dual capacitors was designed and manufactured to replace the traditional LC device. In addition to the inductor and capacitor structure required by the traditional LC device, this paper innovatively designs the fixed capacitor as the inter-layer interconnection structure. The key structural dimensions of the sensor were determined through the numerical analysis of the planar inductor theory and the electromechanical coupling simulation of the dual capacitors model in the previous stage, and the processing of the sensor was carried out through MEMS technology. The final test results showed that within the pressure range of 5kPa to 100kPa, the sensor’s average sensitivity was greater than 69.0 kHz/kPa, while the maximum linear fitting error was smaller than 4.18%. The temperature drift in atmospheric environment was 2.7kHz/°C, and the sensitivity temperature drift was 0.0062kHz/(kPa·°C). [ABSTRACT FROM AUTHOR]

For modular multilevel converter (MMC) based DC grids, current-limiting reactors (CLRs) are mainly employed to suppress the fault current and provide boundary effects to detect internal faults. Thus, most existing protection schemes are highly dependent on the larger CLRs to guarantee high selectivity. However, in existing MMC based HVDC projects, the size of CLRs is restrained by the cost, weight, and system stability under normal state. Thus, boundary protections may fail to detect high-resistance faults and pole-to-ground faults under weak boundary conditions. To overcome these shortcomings, this paper proposes a fast and selective DC fault detection scheme independent of boundary components. The propagation characteristics of line-mode backward traveling-waves (TW) are analyzed to identify external and internal faults. The polarities of zero-mode backward TWs are employed to select faulted poles. The directional overcurrent based pilot protection is adopted as a complementary criterion to detect remote faults. The proposed method can be applied in MMC-HVDC systems with small CLRs that cannot provide strong boundary conditions. Besides, the detection speed is fast (less than 1.5ms). Moreover, it is robust to fault resistance and immune to noise. Various simulation results in PSCAD/EMTDC verifies the effectiveness of the proposed scheme. [ABSTRACT FROM AUTHOR]

The paper examines the possibility to exploit the inductance of wound aluminum foil capacitors in order to realize an integrated component. Objective is the design and construction of an integrated inductor/capacitor to filter harmonic modulations as an alternative to the conventional passive filter, consisting of capacitor and inductor as discrete components with the prospect of reducing size, material and consequently costs. The principle functioning of the integrated component resulting from the position the supply terminals are placed on the aluminum foils is being demonstrated. An analysis of technical and geometric parameters leads through a calculation scheme to the design of such an integrated component. Finally, the construction of a manual winding machine enables the wrinkle free winding of the four foils on a central core to produce a pilot model operational at 400 V with multiple access terminals providing hence diverse experimentation possibilities. Most significant result is the measured current frequency characteristic of the pilot model revealing clearly its series resonant behavior with a quality factor close to ten, well comparable to values of conventional industrial filters indicating thus at this stage reasonable prospects for such an integrated component to operate as a filter in the grid absorbing harmonic modulations. [ABSTRACT FROM AUTHOR]

An electric potential appears at floating wires located within a strong electric field. This phenomenon can be used to supply small isolated communities situated close to Extra-High Voltage transmission lines. This non-conventional distributed generation system has been studied for the last years. However, to improve the power generation system the optimal position of the floating wires, number of wires used, bundle radius, and type of wires must be properly identified. This paper presents a mathematical model solved with genetic algorithm to design a collector system with optimized induced voltage and minimized project cost, identifying the optimal reactor used for voltage regulation. The algorithm was applied to design a collector system that can tap-off 100 kW from a 230 kV transmission line. The trade-off between objectives and the Pareto optimal solutions were evidenced via several simulations using the weighting sum approach. These results allowed to identify a final geometry according to a-posteriori designer preferences. [ABSTRACT FROM AUTHOR]

This paper discusses an artificial neural inversion approach for non-destructive testing of the graphite moderator bricks that make up the cores of Advanced Gas-Cooled Reactors (AGR). The study employed fully connected feedforward neural networks consisting of four hidden layers and trained with backpropagation approach using Levenberg-Marquardt optimisation algorithm. The approach is based on multi-frequency (MF) eddy current (EC) measurements, and combinations of simulated and measured datasets from a laboratory sample and one of the operating reactor core, along with different regularisation parameters were used to train and test the networks. Various types of artificially generated errors were added to the data during training procedures, which in turn allowed for error tolerance and improved the generalisation of the ANNs to unseen test datasets. First, the ANN was tested using unseen simulated data, followed by the measurements collected from laboratory sample and one of the operating reactor core. The first test from the unseen simulated data showed mean profile error ranging between 1.30% and 8.20%, whereas the profiles estimated from reactor core measurements showed mean profile error ranging between 1.84% and 17.80% when compared with the resistivity measurements from trepanned graphite sample taken out of the reactor core. Further comparison of the network outputs against the profiles estimated using traditional iterative inversion algorithm indicates reasonable agreement between the two approaches with the exception of one case, but the solution time for the ANN was found to be over three orders of magnitude faster than the iterative inversion algorithm. [ABSTRACT FROM AUTHOR]

In recent years, very high frequency (VHF) converter has attracted much attention. However, with rich parasitic parameters and complex resonance links, there are some great difficulties to the modeling of such systems. Taking the on-off controlled VHF resonant boost converter as an example, this paper presents an accurate modeling and analysis method that considers multiple parasitic parameters. First, the closed-loop VHF converter system is divided into a main network and a parasitic oscillation network. Then, based on the operation analysis, an equivalent circuit model characterized by a time-varying input voltage source and two variable duty-cycle controlled switches is proposed. It worth noting that both the time-varying input and the controlled switches take into account the influences of the parameters. Furthermore, the periodic approximate analytical solution of the output voltage in the on stage is obtained by using the equivalent small parameter method to the proposed circuit model. And then combining the solution of the parasitic oscillation network and on-off state switching conditions, the steady-state waveform of output voltage can be obtained quickly. Finally, a prototype with operating frequency of 21.44 MHz is built to verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

A novel single-stage doubly grounded transformerless inverter configuration which can buck-boost the output voltage is proposed in this paper. In this transformerless inverter configuration grid neutral is directly connected to PV panel negative rail which suppresses/eliminates the PV leakage currents. In addition, the tracking of maximum power point is possible for wide variation of weather conditions due to buck-boost voltage capability of inverter. Moreover, the proposed inverter topology has symmetrical operation in both half cycles hence injects negligible DC offset current in to the grid. Here the symmetrical operation of inverter is achieved due to one inductor is used for both half cycles of the grid. The proposed topology is realized using five switches, two of which work at 50 Hz and remaining three switches at high frequency which reduces overall semiconductor losses. Further, the proposed inverter topology is controlled through a newly developed modulation technique and possible working modes are analyzed and described thoroughly. For performance validation, the experimental analysis of grid connected proposed inverter is performed on a 1 kVA system and results show that proposed inverter feeds power in to the grid with lesser THD while achieving greater efficiency. [ABSTRACT FROM AUTHOR]

The modular multilevel converter (MMC), owing to the presence of a large number of submodules (SMs) and energy storing elements, requires a large footprint and initial investment. To address these issues, this paper proposes the switched modular multilevel converter (SMMC). It consists of two major elements; the chain-links (CLs), consisting of cascade connection of SMs as in MMC, and the single-pole-triple-throw (SPTT) switches, which can be realized using either the T-type or NPC-type switch strings. The SMMC works on the principle of connecting all the phase-legs in series and their respective positions are mutually interchanged. It offers a compact structure as the SMs count is reduced to 33% of MMC, which results in a much lower energy storage requirement. Furthermore, it does not have inter-phase circulating current problem and hence the CL inductors can also be avoided. The SMMC structure, operating principles, control, and modulation schemes are explained in detail. A detailed comparison of SMMC with the other major existing converters is carried out to highlight the important features of SMMC. The efficacy of SMMC is validated using PSCAD simulation studies with a 19-level grid-connected SMMC model. A 3-phase 19-level SMMC laboratory prototype is developed to further validate its feasibility. [ABSTRACT FROM AUTHOR]

This paper presents a modified post-distortion (PD) linearization technique for cascode common-gate low noise amplifiers (CG-LNAs) working at high frequencies up to millimeter-wave band. This technique utilizes an auxiliary transistor together with an inter-stage inductor to suppress the third order distortion without degrading gain. The input third order intercept point (IIP3) of the linearized CG-LNA is improved by a factor of up to 12 dB. For demonstration, an mm-wave differential CG-LNA was fabricated based on a 65-nm CMOS process. It achieves 2.4–10.6 dBm IIP3, 9.6–12 dB gain, 5.0–5.45 dB NF over 26–31 GHz and consumes 14.4 mW from a 1.2 V supply. [ABSTRACT FROM AUTHOR]

This brief overviews the development of high-performance single-core voltage-controlled oscillators (VCOs) employing a multi-LC tank over the past two decades. From the circuit-design perspective, we study the key breakthroughs for constantly heightening the figure-of-merit and lowering the 1/f3 phase-noise corner, according to the noise source and transfer, narrow and wideband performance optimization, as well as one- and two-dimensional (1D/2D) tuning. We also aim to present the prospects of single-core VCOs. [ABSTRACT FROM AUTHOR]

Along with the commercialization of SiC‐MOSFETs and progress in the development of GaN power devices, high‐speed, high‐frequency switching and reduction in conduction loss of power devices are expected. Hence reduction of the size and increase of conversion efficiency of power electronics equipment is greatly expected. On the other hand, even if power devices are switched at high speed and high frequency, the loss of passive devices such as transformers, inductors, and capacitors used in power converters increases, making it difficult to make the power converters smaller than expected. In other words, there is a demand for performance improvements of passive devices from various viewpoints, including miniaturization and low loss, which are compatible with high‐speed, high‐frequency switching operations of power devices. This paper introduces recent research results on loss evaluation methods considering the operating state of passive devices used in small‐to‐medium‐capacity power converters those perform high‐frequency switching operations. © 2023 Institute of Electrical Engineer of Japan and Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]