Search

The significance of using the variable step Incremental Conductance (INC) technique in Maximum Power Point monitoring (MPPT) of photovoltaic (PV) systems resides in its capacity to improve the efficiency of energy conversion. This is accomplished through the constant measurement and comparison of incremental changes in current and voltage, precisely monitoring the maximum power point amidst changing environmental conditions. This traditional INC-MPPT approach has two primary disadvantages. Initially, it employs a predetermined scaling factor that necessitates human adjustment. Furthermore, it adjusts the inclination of the PV characteristics curve to modify the step size. This implies that even little changes in PV module voltage will have a substantial impact on the total step size. As a result, it shifts the operating point away from the intended reference maximum power point. The objective of this work is to improve the efficiency of traditional INC by overcoming the constraints associated with step size modifications. This is achieved by using a fuzzy logic (FL) technique to adjust the step size adaptively in response to environmental changes. The presented INC-FL-MPPT successfully achieves MPPT for a PV system under enhanced steady-state and transientstate settings. The results demonstrate the superiority of the suggested approach compared to three distinct MPPT strategies, namely Perturb and Observe (P&O), Classical INC, and P&O-FL technique. [ABSTRACT FROM AUTHOR]

Solar energy, a prominent renewable resource, relies on photovoltaic systems (PVS) to capture energy efficiently. The challenge lies in maximizing power generation, which fluctuates due to changing environmental conditions like irradiance and temperature. Maximum Power Point Tracking (MPPT) techniques have been developed to optimize PVS output. Among these, the incremental conductance (INC) method is widely recognized. However, adapting INC to varying environmental conditions remains a challenge. This study introduces an innovative approach to adaptive MPPT for grid-connected PVS, enhancing classical INC by integrating a PID controller updated through a fuzzy self-tuning controller (INC-FST). INC-FST dynamically regulates the boost converter signal, connecting the PVS's DC output to the grid-connected inverter. A comprehensive evaluation, comparing the proposed adaptive MPPT technique (INC-FST) with conventional MPPT methods such as INC, Perturb & Observe (P&O), and INC Fuzzy Logic (INC-FL), was conducted. Metrics assessed include current, voltage, efficiency, power, and DC bus voltage under different climate scenarios. The proposed MPPT-INC-FST algorithm demonstrated superior efficiency, achieving 99.80%, 99.76%, and 99.73% for three distinct climate scenarios. Furthermore, the comparative analysis highlighted its precision in terms of control indices, minimizing overshoot, reducing rise time, and maximizing PVS power output. [ABSTRACT FROM AUTHOR]

The integration of renewable sources (RSs) and the widespread deployment of electric vehicles (EVs) has transitioned from a luxury to a necessity in modern power systems. This results from the sharp increase in electric power demand and public awareness of switching to green energy. However, in addition to load fluctuations and changes in system parameters, these RSs and EVs negatively impact the load frequency (LF). This work presents a LF control for a modern multi-area power system incorporating photovoltaic (PV) and EV chargers. The proposed controller primarily utilizes EV chargers within modern power systems. This approach offers the advantage of using the already present components instead of introducing new ones. The proposed controller comprises the ecological optimization approach (ECO) and the integral controller (I). Both of these components are designed for autonomous vehicle-to-grid (V2G) devices. The proposed control technique is applied to a three-area power system, where the V2G scheme is located in Area-1. Variations in the load, PV power generated, and system parameters are considered to evaluate the effectiveness of the proposed (I+ECO+V2G) controller for controlling the LF. To assess the performance of the proposed I+ECO+V2G system, a comparative analysis is conducted to compare its performance with both the I+ECO system and the standard I-controller. The simulation findings demonstrate that implementing the I+ECO and the proposed I+ECO+V2G strategies results in enhanced system stability and decreased LF fluctuations compared to the conventional I-control approach. Furthermore, while comparing the I+ECO control technique to the suggested control strategy I+ECO+V2G, it was seen that the latter reaches steady state values more quickly. The results validate the robustness and effectiveness of the proposed controller in mitigating the impacts of load disturbances, uncertainties, and nonlinearities within the system. These simulations were performed using MATLAB/SIMULINK. To validate the outcomes of the simulation results, an experimental setup consisting of a real-time dSPACE DS1103 connected to another PC via QUARC pid_e data acquisition card was used. The experimental findings have substantiated the accuracy of the simulation findings about the superiority of the I+ECO+V2G methodology compared to both the I+ECO and I-control methodologies concerning system performance and LF control. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) systems are crucial to the production of electricity for a newly established community in Egypt, especially in grid-tied systems. Power quality (PQ) issues appear as a result of PV connection with the power grid (PG). PQ problems cause the PG to experience faults and harmonics, which affect consumers. A series compensator dynamic voltage restorer (DVR) is the most affordable option for resolving the abovementioned PQ problems. To address PQ difficulties, this paper describes a grid-tied PV combined with a DVR that uses a rotating dq reference frame (dqRF) controller. The main goal of this study is to apply and construct an effective PI controller for a DVR to mitigate PQ problems. The artificial rabbits optimization (ARO) is used to obtain the best tune of the PI controller. The obtained results are compared with five optimization techniques (L-SHADE, CMAES, WOA, PSO, and GWO) to show its impact and effectiveness. Additionally, Lyapunov's function is used to analyze and evaluate the proposed controller stability. Also, a mathematical analysis of the investigated PV, boost converter, and rotating dqRF control is performed. Two fault test scenarios are examined to confirm the efficacy of the suggested control approach. The parameters' (voltage, current, and power) waveforms for the suggested system are improved, and the system is kept running continuously under fault periods, which improves the performance of the system. Moreover, the findings demonstrate that the presented design successfully keeps the voltage at the required level with low THD% values at the load side according to the IEEE standards and displays a clear enhancement in voltage waveforms. The MATLAB/SIMULINK software is used to confirm the proposed system's performance. [ABSTRACT FROM AUTHOR]

In recent times, renewable energy systems (RESs) such as Photovoltaic (PV) and wind turbine (WT) are being employed to produce hydrogen. This paper aims to compare the efficiency and performance of PV and WT as sources of RESs to power polymer electrolyte membrane electrolyzer (PEMEL) under different conditions. The study assessed the input/output power of PV and WT, the efficiency of the MPPT controller, the calculation of the green hydrogen production rate, and the efficiency of each system separately. The study analyzed variable irradiance from 600 to 1000 W/m2 for a PV system and a fixed temperature of 25°C, while for the WT system, it considered variable wind speed from 10 to 14 m/s and zero fixed pitch angle. The study demonstrated that the applied controllers were effective, fast, low computational, and highly accurate. The obtained results showed that WT produces twice the PEMEL capacity, while the PV system is designed to be equal to the PEMEL capacity. The study serves as a reference for designing PV or WT to feed an electrolyzer. The MATLAB program validated the proposed configurations with their control schemes. [ABSTRACT FROM AUTHOR]

The voltage quality (VQ) index has become a significant measure of recent power system stability. The integration of photovoltaic (PV) systems plus smart home loads (SHLs) at low voltage levels (LVLs) has resulted in various issues such as harmonics rise and voltage instabilities as a result of faults and systems nonlinearity. In this work, a dynamic voltage resistor (DVR) is implemented to enhance VQ, and its dynamic performance hinges on its control system ability. To enhance the DVR's control system, for surpassing nonstandard voltage with a quick response and harmonics reduction at LVL under harsh operating events, an optimal controller design using the Harris Hawks algorithm (HHA) is proposed. To verify the value of the suggested solution, the hard operating events (voltage sag, voltage swell, fluctuating voltage, and imbalanced voltage) are examined and assessed. To show the effectiveness of the HHA technique, a comparison of the % total harmonic distortion (THD) reductions achieved by the suggested and conventional controllers of DVR is conducted for the scenarios under study. Moreover, the suggested controller stability is analyzed and assessed using Lyapunov's function. The benefits of the optimized controller system are inferred from the results, including their robustness, simplicity, efficient harmonic rejection, minimal tracking error, quick response, and sinusoidal reference track. The results of the simulation show that the DVR's optimized controller is efficient and effective in maintaining a voltage at the needed level with low THD, safeguarding the sensitive load as expected, and showing a noticeable improvement in voltage waveforms. The mathematical modeling of HHA, PV system, DVR, and SHLs are all verified using MATLAB\Simulink. [ABSTRACT FROM AUTHOR]