Search

Maturity evaluation of highly evolved organic matter is an important problem in oil and gas geochemistry, because conventional organic geochemical proxies are not applicable due to hydrocarbon generation and expulsion. In this study, we investigated the pyrobitumen in the reservoirs of the Sinian Dengying Formation in the Sichuan Basin, China. We focused on aromatic hydrocarbon biomarkers, and the calibration and application of aromatic maturity proxies using pyrobitumen reflectance and Raman spectral parameters. Our results show that only the thiophene compounds are effective maturity indicators, such as MDR (4-/1-MDBT), MDR′ (4-MDBT/(1-MDBT+4-MDBT)), MDR1 (1-MDBT/DBT), 4,6-/(1,4+1,6)-DMDBT, (2,6 +3,6)-/(1,4+1,6)-DMDBT, and [2,1]BNT/([2,1]BNT+[1,2]BNT), as these are largely independent of the optical anisotropy of pyrobitumen The condensation and incorporation of thiophene compounds can lead to an increase in the reflectance of pyrobitumen, which means the thiophene compound parameters are positively or negatively correlated with pyrobitumen reflectance New potential maturity parameters were proposed, including DMDBTs/MDBTs, TeMDBTs/(DBT+MDBTs +DMDBTs+TMDBTs+TeMDBTs), 1-MDBT/MDBTs, and [2,1]BNT/BNTs. This method and these parameters are universally applicable to maturity characterization, especially in rocks that lack vitrinite, contain strongly anisotropic organic matter, and have high contents of thiophene compounds. [ABSTRACT FROM AUTHOR]

Large quantities of gas resources have been found in the Paleo-Mesozoic carbonate rocks in the Sichuan Basin. However, many wells cannot obtain high production in deep low porosity-permeability reservoirs. For this contribution, we provide a steerable pyramid method for identifying the fault damage zone in the Kaijiang–Liangping platform margin, which is infeasible by conventional seismic methods. The results show that steerable pyramid processing could enhance the seismic fault imaging and a series of NW-trending strike-slip faults are found along the trend of the carbonate platform margin. The steerable pyramid attribute presents distinct vertical and horizontal boundaries of the fault damage zone, and heterogeneous intensity of an un-through-going damage zone. The width of the fault damage zone is generally varied in the range of 100–500 m, and could be increased to more than 1000 m in the fault overlap zone, intersection area, and fault tips. Further, the fault damage zone plays a constructive role in the high gas production in the deep tight carbonate reservoir. The results suggest the steerable pyramid method is favorable for identifying the weak strike-slip faults and their damage zone. The width of the fault damage zone is closely related to fault displacement, and the much wider damage zone is generally influenced by the fault overlapping and interaction. The fractured reservoirs in the fault damage zone could be a new favorable exploitation domain in the Sichuan Basin. [ABSTRACT FROM AUTHOR]

The Middle-Upper Cambrian Xixiangchi Formation in the Sichuan Basin is regarded as an important reservoir with great potential for hydrocarbon exploration. It is previously indicated that the Xixiangchi carbonates have experienced extensive dolomitization, however, the origin of dolomitizing fluids and the dolomitization mechanism still remain uncertain. In this study, a set of petrographic and geochemical examinations, including rare earth elements (REE) and isotopic (C, O, and Sr) compositions were used to trace the origins of dolomitizing fluids and associated diagenetic processes. The petrographic examination revealed three types of matrix dolomites (D1, D2, D3) and one cement saddle dolomite (SD). These phases have crystal size ranges of less than 30 μm (very fine to fine crystals, D1), 30–100 μm (fine to medium crystals, D2), 100–300 μm (medium to coarsely crystalline dolomite, D3), and 0.3–4 mm (fracture filling cements, SD), respectively. D1 is characterized by non to very weak luminescence, weakly negative Ce anomalies (Ce/Ce* = 0.84 ± 0.02), strongly negative Eu anomalies (Eu/Eu* = 0.65 ± 0.03), and high 87Sr/86Sr ratios (0.71062 ± 0.00122). In combination with δ13C (−1.5‰ ± 0.2‰) and δ18O (−9.7‰ ± 0.5‰) compositions, D1 is interpreted to be formed by penecontemporaneous dolomitization in the near-surface environment with seawater as the dolomitizing fluid. In contrast, D2 is characterized by intercrystalline pores, dirty crystal surfaces, similar δ13C (−1.4‰ ± 0.4‰) compositions but higher δ18O (−8.9‰ ± 0.7‰) compositions, and lower 87Sr/86Sr ratios (0.70992 ± 0.00035), similar Ce anomalies (Ce/Ce* = 0.87 ± 0.04) and higher Eu anomalies (Eu/Eu* = 0.85 ± 0.04). The coarser D2 is regarded to be formed by the post-penecontemporaneous seepage-reflux dolomitization or by recrystallization of D1 dolomite in a near-surface or shallow burial environment. D3 is distinguished by a cloudy core with clear rims, showing slightly higher Eu anomalies (Eu/Eu* = 0.88 ± 0.02) and similar Ce anomalies (Ce/Ce* = 0.88 ± 0.02) than those of D1 and D2. Combined with the δ18O compositions (−10.4‰ ± 0.4‰) and 87Sr/86Sr ratios (0.70989 ± 0.00048), D3 is thought to be formed by the overgrowth or recrystallization of D1 and D2 dolomites in a shallow to moderate burial environment. The fractures filling SD dolomite consists of nonplanar and much coarser crystals with undulatory extinctions and brighter red luminescence. The lower δ18O (−11.1‰ ± 0.3‰) compositions, lower negative Eu anomalies (Eu/Eu* = 0.70 ± 0.01) of SD than the matrix dolomites, and similar Ce anomalies (Ce/Ce* = 0.83 ± 0.01) are indicative of hydrothermal dolomitization, with possible fluids associated with the magma during the period of Emei taphrogenic movement. In addition, the 87Sr/86Sr ratios (0.70941 ± 0.00003) of SD suggest probable origin from the coeval seawater partially. Therefore, SD dolomite is interpreted to be formed by hydrothermal dolomitization with mixed dolomitizing fluid of seawater and hydrothermal fluids. In summary, all the matrix dolomites have almost the same ΣREE concentrations and exhibit similar near-flat REE partition patterns with weak LREE enrichments, weakly negative Ce anomalies, and negative Eu anomalies. Such characteristics of REE compositions are indicative of similar evolved dolomitizing fluid, such as seawater or seawater- derived fluids. By contrast, SD dolomites have a different REE partition pattern with left-leaning characteristics, LREE depletions, and negative Eu anomalies, thus suggesting a different dolomitizing fluid source from the matrix dolomites. In addition, the development of intercrystalline pores associated with D2 dolomite makes it more likely to be a potential reservoir, indicating that the dolomitizing history of carbonate has a strong influence on the quality of potential dolomite reservoirs. [ABSTRACT FROM AUTHOR]

Based on 2D and 3D seismic data, the latest drilling data and field outcrop data of the northern slope of the Central Sichuan paleo‐uplift, the structural analysis method is used to analyze unconformity development characteristics and fault characteristics during the key structural transformation period, discussing the influence of the structural characteristics on the hydrocarbon accumulation of deep carbonate rocks. The results show that: (1) The two key unconformities of the Tongwan and Caledonian periods were primarily developed in deep carbonate rocks. Firstly, Tongwan's unconformities are characterized by regional disconformities between the second and third members of the Dengying Formation, the top formation of the Sinian and the lower Cambrian, strips of which zigzag through the north and south sides of the study area. Secondly, the Caledonian unconformity is characterized by a regional unconformable contact between the lower Permian and the ower Paleozoic strata. From NE to SW, the age of the strata, which were subject to erosion, changes from new to old, the denudation distribution showing as a nose‐shaped structure which inclines towards the ENE. (2) Boundary fault and transtensional strike‐slip faults developed in the Sinian to Paleozoic strata. In profile, there are three types of structural styles: steep and erect, flower structures, 'Y' and reversed 'Y' type faults. In plane view, the Sinian developed extensional boundary faults extending in an almost NS direction, strike‐slip faults developing and extending linearly in approximately EW, WNW and NE strikes in the Cambrian, with characteristically more in the south and less in the north. (3) The faults in the northern slope show obvious zonal deformations in transverse view as well as significant stages and stratified activity in a longitudinal direction. Among them, the activity of faults in the Sinian was the strongest, followed by the activity in the Cambrian period, the activity intensity of faults in the Permian period being the weakest. This fault activity can be divided into four periods: Sinian, Cambrian‐Permian, the early Indosinian period and the late Indosinian‐Himalayan period, the transtensional strike‐slip faults being the products of oblique extensions of pre‐existing weak zones in the Xingkai and Emei taphrogenesis, with a particular inheritance in the main faults. (4) Combined with hydrocarbon accumulation factors, it is considered that the epigenetic karstification of the Tongwan and Caledonian unconformities in the northern slope controlled the formation and distribution of carbonate karst reservoirs over a large area, also acting as a good pathway for oil and gas migration. The extensional faults developed at the margin of the NS trending rift, controlling the sag‐platform sedimentary pattern in the Dengying Formation of the Sinian. Strike‐slip faults in NE, WNW and ENE directions may control the micro‐geomorphological pattern inside the platform and intensify the differential distribution of grain beach facies. The multi‐stage hereditary activity of strike‐slip faults not only improved the porosity and permeability of the reservoirs, but also acted as the main channel of oil and gas migration, providing favorable conditions for the development of the current multi‐layer gas‐bearing scenario in the northern slope of the Central Sichuan Basin. [ABSTRACT FROM AUTHOR]

Deep-seated faults and folds of foreland basin systems have become important exploration targets in the recent years because they are crucial in controlling fluid migration and hydrocarbon accumulation. In this study, we analyzed the characteristics and formation history of these structures in the northwestern Sichuan Basin using recently acquired two-dimensional (2D) and three-dimensional (3D) seismic data. The seismic interpretation revealed that the thrust sheets, tectonic wedges, and foredeep were well developed in the northwestern Sichuan Basin from the mountain to the basin. Forward thrusts, fault-bend folds, and wedges are the main types of structures in the thrust sheets and tectonic wedges. The deep-seated faults and folds were easily recognized in the high-resolution 3D seismic data. The imbricate thrust faults that merged into detachment layers of the Lower Cambrian are the main types of structures in the foredeep, and they show a prominent strike-slip influence in the horizontal direction. The formation of these structures in the foredeep in the northwestern Sichuan Basin mainly endured two stages of thrusting, including those during the Middle-to-Late Triassic and Cenozoic. Based on the tectonic evolution and seismic data, we infer that these deep-seated faults and folds in the foredeep may have formed earlier than the northern Longmen Shan fold-and-thrust belts and they may have been initially active in the late of Early Triassic and reactive during the Cenozoic. Furthermore, evaporites in the Lower and Middle Triassic were crucial in forming these structures. The petroleum exploration data suggested that the deep-seated faults can facilitate hydrocarbon accumulation. The thrust faults in the foredeep were more likely to act as migration pathways for fluids instead of sealing barriers along the horizontal direction. The interconnected reservoirs of deep-seated folds possess a great potential to allow large-scale hydrocarbon accumulation. Our study provides a good example for evaluating the hydrocarbon exploration potential in the deeply buried area in the sedimentary basin. [ABSTRACT FROM AUTHOR]

Determining the present-day stress orientation is essential for the exploration and development of shale gas. The Longmaxi Formation is the most significant shale gas reservoir in the Jiaoshiba Area of the Sichuan Basin, China. However, little is known about the orientation of the maximum horizontal stress (S Hmax) and the factors influencing it within the formation. In this study, the orientation of the S Hmax in the Jiaoshiba Area was determined based on observations of drilling-induced fractures on resistivity image logs. Then, the tectonic activity, the mechanical properties of the rock, and finite element simulations were studied in detail to determine the major factors influencing the S Hmax orientation in the Jiaoshiba Area. The results show that the S Hmax orientation within the study area ranges from nearly EW to NEE-SWW. The vertical variations of the in-situ stress orientation are controlled by the structural strength and the mechanical properties of the rock. In the area that has experienced intense tectonic movements, the deviation in the S Hmax orientation (from 30° to 80°) was caused by the differences in the mechanical properties of the rocks. The finite element simulations indicate that the lateral variations in the S Hmax orientation was mainly controlled by the faults. The stress rotation near the end of the fault is 14°–21° higher than that in the middle of the fault. Furthermore, the stress variation caused by the mechanical properties of the fault zone ranges from 12° to 18°, and this deviation increases as the Young's modulus of the fault zone decreases. In the study area, the azimuth deflection (18°–46°) of the S Hmax orientation influenced by the NE faults is higher than that (12°–36°) influenced by the nearly NS faults, which is the main reason for the lateral stress rotation. • Variations of the S Hmax orientation in shales were determined from DIFs. • Influence factors of the S Hmax orientation in shales were discussed. • FE simulation shows that faults control variations of the S Hmax orientation in the horizontal direction. • Variations of the S Hmax orientation were affected by rock mechanical properties in the vertical direction. [ABSTRACT FROM AUTHOR]

Deep marine carbonate oil and gas resources in the Sichuan Basin are currently key exploration areas. As an important tectonic thermal event, the Emeishan mantle plume has an important influence on the source rocks under the Middle-Lower Permian in the Sichuan Basin. Therefore, the better understanding of the effect of Emeishan basalt eruption on source rock is vital for the exploration of marine oil and gas resources. On the basis of the thermal history study of the Sichuan Basin, this study restored the thermal maturity of the algal dolomite of the Sinian (Ediacaran) Dengying Formation in the Sichuan Basin in normal evolution. Using the hydrocarbon generation potential variation method, the hydrocarbon generation and expulsion characteristics of normally evolved algal dolomite and algal dolomite affected by basalt eruption were calculated. Through comparison, the influence of the Emeishan mantle plume on the algal dolomite of the Sinian Dengying Formation is analyzed. The research indicates that the thermal effect of the Emeishan mantle plume promotes the maturation of algal dolomite, which leads to the shortening of the oil generation period and the early arrival of the gas generation peak. The main hydrocarbon expulsion period of the normally evolved algal dolomite should be from the end of the Triassic to the end of the Jurassic, while the main hydrocarbon expulsion period of the algal dolomite affected by basalt eruption was advanced to the end of Silurian to the end of Triassic. In the current period, due to the high maturity of algal dolomite, the Emeishan mantle plume has little impact on the total resources. • Influence of Emeishan mantle plume on hydrocarbon generation and expulsion characteristics of algal dolomite of Sinian Dengying Formation. [ABSTRACT FROM AUTHOR]

The origin of Precambrian dolomites has attracted research interest as a result of their association with petroleum resources. The long diagenetic history of these dolomites and multiple periods of hydrothermal activity mean that dating and identifying different periods of dolomite formation is challenging. This study focuses on dolomites in the Precambrian Dengying Formation of the Sichuan Basin, central China, and presents new petrographic, in situ laser ablation inductively coupled plasma mass spectrometry U–Pb and trace element, and Sr–C–O isotopic data to characterize three types of dolomite and constrain their age and origin. In situ U–Pb dating of type I dolomite yielded a lower intercept age of 637 ± 35 Ma. The rare earth element (REE) patterns, 87Sr/86Sr ratios (0.70827–0.70903), and δ13C VPDB (0.8‰–1.0‰) and δ18O VPDB (−1.5‰ to −1.0‰) values of type I dolomite indicate their derivation from seawater or a precursory source with seawater characteristics. Type II dolomite yielded an age of 636 ± 15 Ma and has lower ΣREE and slightly higher δ13C VPDB (1.2‰–1.5‰) and δ18O VPDB (−0.9‰ to −0.3‰) values than type I, as well as similar 87Sr/86Sr ratios and parallel REE patterns that are indicative of formation by reflux seepage dolomitization. The type III dolomite is characterized by large crystals, unique REE patterns, high 87Sr/86Sr values (0.70942–0.70975), and negative δ18O VPDB values (−6.4‰ to −3.1‰) that indicate a hydrothermal origin. The relationships between hydrothermal dolomite and bitumen indicate that the paleo-oil charging within the Dengying Formation reservoir occurred after the hydrothermal activity at 516 ± 49 Ma. The early hydrothermal activity provided space for the subsequent fluid movement, and oil and gas charging. Our integrated approach, incorporating petrographic, geochemical, isotopic, and geochronological data, constrains the ages of different dolomite phases and an oil-charging event within the Dengying Formation reservoir and provides new insights into the evolution of petroleum systems in general. • We identified three types of dolomites of Dengying Formation matching with the age of diagenesis and fluid activity. • The LA–ICP–MS in situ U–Pb dating of Dengying Formation dolomite yields a lower intercept age of 637 ± 35 Ma. • The dating results suggest an extensional event existed at 516 ± 49 Ma, and accounted for the deposition of hydrocarbon source rocks. • This study outlines potential approaches for furthering our understanding of dolomites and ancient petroleum systems. [ABSTRACT FROM AUTHOR]

Inorganic geochemical approaches (i.e., trace elements) for hydrocarbon–source rock correlations in sedimentary basins are a frontier area of research in petroleum geochemistry. This study used inorganic geochemistry to the over mature petroleum systems in the Sinian (Neoproterozoic) Dengying Formation in the Sichuan Basin of China. Our results show that the Ba N –Ni N –Cu N ternary diagram, V N –Ni N –Mo N ternary diagram and V/Ni–U/Th diagram (related to paleo-productivity and redox conditions), rare earth element (REE)–Y patterns, Ce/Ce*–La/La* diagram, and Ce/Ce*–La/La*–(LREE/HREE) N ternary diagram (related to fluid interactions) can robustly distinguish different source rocks. In particular, V, Ni, and Mo have a strong relationship to organic matter in source rocks, while their occurrence is most likely related to porphyrins in petroleum. Therefore, the V N –Ni N –Mo N ternary diagram can be used for hydrocarbon–source rock correlations. In contrast, Ba, Cu, U, Th, and REE–Y have different and complex geochemical behaviors, limiting the application in hydrocarbon–source rock correlations. The application in the Sichuan Basin shows that the hydrocarbons in the Dengying reservoir were mainly derived from the lower Cambrian Qiongzhusi Formation with minor contribution from the lower Cambrian Maidiping and Sinian Doushantuo formations. Compiled data from Lower Paleozoic crude oils in the Tarim Basin show that the V N –Ni N –Mo N ternary diagram can also be applied to low-maturity crude oil systems. Therefore, V, Ni, and Mo have strong relationship to organic matter in petroleum systems and the potential for hydrocarbon–source correlation, while other elements should be used under given conditions. [ABSTRACT FROM AUTHOR]

The Leikoupo Formation, which was deposited during the Anisian stage in the central Sichuan Basin, has produced significant amounts of conventional gas but there have been few studies on its unconventional resources. Organic-rich shale in the Leikoupo Formation was discovered for the first time in the wells of CT1 and JY1 in the central Sichuan region, but information on its sedimentary environment and climate evolution is scarce. A series of lithofacies, organic geochemistry and inorganic geochemistry analyses were used to analyse core samples of CT1 and JY1 to estimate their vertical changes. The organic matter characteristics, the sedimentary environment and the factors controlling the Leikoupo Formation shale in the Sichuan basin were revealed. The organic-rich shale of the Lei3-2 sub-member was formed in a semi-restricted lagoon environment. The sedimentary environment was dysoxic-anoxic, with high palaeoproductivity, a warm and humid to semi-arid and semi-humid climate. The vertical sea level decreased for a short period, led to an increase in oxygen content in the mixed shale, clayey shale and calcareous shale that were sequentially deposited from bottom to top. In the vertical direction, the palaeo-productivity and aridity decreased, and there was an increase in the salinity and terrigenous debris input. All of these corresponded well with TOC. According to Mo-TOC and Mo–U patterns, the mixed shale was characterised by the highest values of Mo EF , U EF and Mo EF /U EF , followed by clayey shale and calcareous shale, which indicated mixed shale was deposited in a moderately restricted water condition, which progressively became more restricted during the deposition of clayey shale and calcareous shale with the fall of relative sea level. Biomarker compounds (steranes, terpanes), Tmax and other pyrolysis parameters indicated that the organic matter had reached the stage of high-to over-maturity. The gammacerane to C 30 hopane in the ratio indicated that it was the bottom water in which it was deposited was sratified. • The first discovery of Lei3-2 sub-member shale in the Sichuan Basin. • The shale has good original hydrocarbon generation potential. • The shale was formed in a semi-confined environment. • Lithological changes reflect variations in sedimentary environment and sea level. [ABSTRACT FROM AUTHOR]

The Lower Triassic Jialingjiang Formation, characterised by a carbonate–evaporite succession, is one of the important pay layers in the eastern Sichuan Basin. Several diagenetic events were identified in this study, including meteoric dissolution, dolomitisation, anhydrite/gypsum replacement/cementation, TSR, BSR, and multiple calcite cementation (C1–C3). Dolomitisation and anhydrite/gypsum replacement/cementation are the major diagenetic events affecting reservoir porosity. The dolostone is composed of D1, D2, and D3 dolomite. D1 dolomite is very finely crystalline, dominating in the low-energy, restricted depositional facies. D2 dolomite is finely crystalline, constituting a major portion of the dolostones. D3 dolomite is depositional fabric retentive dolomite, including dolo-wacke-/packstone, dolo-grainstone, and dolo-boundstone. Four types of anhydrites (A1–A4) were identified in the core and thin sections. A1 is stratabound anhydrite. A2 is the anhydrite in dolostones, filling in the interparticle spaces in dolo-grainstone and the intraparticle spaces in dolo-wackestone. A3 is the anhydrite in limestones, which occurs non-fabric-selectively. A4 is the anhydrite filling in the fractures. The diagenetic anhydrites (A2–A4) are interpreted to postdate to major dolomitisation. D1 and D2 dolomites are characterised by δ13C VPDB values of −3.4–+7.3 ‰ and δ18O VPDB values of −4.7−-2.4 ‰. The REE patterns of D1–D3 dolomites are characterised by light rare earth element (LREE) depletion relative to heavy rare earth elements (HREE) ((Pr/Tm) N of 0.54–1.16, 0.81 ± 0.20), middle rare earth elements (MREE) enrichment (BSI values of 1.06–1.38, 1.26 ± 0.10), and negative Ce anomalies (Ce/Ce* ratios of 0.74–0.94, 0.83 ± 0.07). The diagenetic anhydrites (A2–A4) show δ34S V-CDT values of +25.9–+45.7 ‰, similar to those of the stratabound anhydrite (+29.6–+43.0 ‰). The large variations in the δ13C VPDB values of D1 and D2 dolomites are attributed to methanogenesis and BSR. The δ18O VPDB values and REE characteristics of D1–D3 dolomites suggest that the carbonates are dolomitised by the mesohaline fluid. The δ34S V-CDT values of A1–A4 indicate that the diagenetic anhydrites are formed by redistribution in a closed system. The petrographical and geochemical data suggest that the Jialingjiang carbonate evolved in a closed system during burial diagenesis. Primary pores dominate in the Jialingjiang carbonate reservoirs, and the boundstone and grainstone show the best porosities based on the porosityversus lithofacies data. Therefore, we propose that the lithofacies, instead of the diagenetic events, are the key factors of the Jialingjiang carbonate. The resisting compaction of dolomitisation helps preserve the reservoir porosity, and anhydrite is the major diagenetic event destroying the reservoir porosity. • Lithofacies are the key factor of the reservoir qualities. • Petrography and geochemical work suggest the closed diagenetic systems. • Jialingjiang carbonate is dolomitized by mesohaline fluids predating diagenetic anhydrite. • Anhydrite selectively replace calcitic part in Jialingjiang carbonate. [ABSTRACT FROM AUTHOR]