Search

Purpose: Subretinal (SR) injection in porcine models is a promising avenue for preclinical evaluation of cell and gene therapies. Targeting of the subretinal fluid compartment (bleb) is critical to the procedure, especially if treatment of the cone-rich area centralis is required (i.e., visual streak [VS] in pigs). To our knowledge, this study is the first to investigate the influence of injection site placement on VS involvement in the pig eye., Methods: We performed 23-gauge pars plana vitrectomy followed by SR injection in 41 eyes of 21 animals (Sus scrofa domesticus). In 27 eyes (65.9%), the injection site was placed superior to the VS, and in 14 eyes (34.1%) it was placed inferior to it. Using intraoperative imaging, blebs were classified based on their propagation behavior relative to the VS., Results: In 79% of cases, blebs from inferior injection sites developed away from the VS, exhibiting a mean ± SEM vertical anisotropy (AP) of 0.67 ± 0.11. In contrast, blebs from superior injection sites tended to develop toward the VS with an AP of 1.27 ± 0.18 (P = 0.0070). Blebs developed away from the VS in only 41% of injections (P = 0.0212). Inferior blebs were orientated close to 0° (horizontal), whereas superior blebs displayed varied orientations with a mean angle of 56° (P = 0.0008)., Conclusions: Bleb propagation was anisotropic (i.e., directionally biased) and dependent on injection site placement. Superior injection sites led to superior VS detachment. Morphological analysis suggested increased adhesion forces at the VS and superior vascular arcades. This study will aid the planning of surgeries for targeted subretinal delivery in pig models.

Purpose of Study: Total joint replacements (TJR) have become the cornerstone of modern orthopedic surgery. A great majority of TJR employs ultrahigh molecular weight polyethylene (UHMWPE) liners. TJR manufacturers use many different types of UHMWPE, which are modified by various combinations of crosslinking, thermal treatment, sterilization and/or addition of biocompatible stabilizers. The UHMWPE modifications are expected to improve the polymer's resistance to oxidative degradation and wear (release of microparticles from the polymer surface). This manuscript provides an objective, non-commercial comparison of current UHMWPE formulations currently employed in total knee replacements., Materials and Methods: UHMWPE liners from 21 total knee replacements (TKR) were collected which represent the most implanted liners in the Czech Republic in the period 2020-2021. The UHMWPEs were characterized using several methods: infrared microspectroscopy (IR), non-instrumented and instrumented microindentation hardness testing (MH and MHI), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and solubility measurements. The above-listed methods yielded quite complete information about the structure and properties of each UHMWPE type, including its potential long-term oxidation resistance., Results: For each UHMWPE liner, IR yielded information about immediate oxidative degradation (in the form of oxidation index, OI), level of crosslinking (trans-vinylene index, VI) and crystallinity (CI). The MH and MHI testing gave information about the impact of structure changes on mechanical properties. The remaining methods (DSC, TGA, and solubility measurements) provided additional information regarding the structure changes and resistance to long-term oxidative degradation. Statistical evaluation showed significant differences among the samples as well as interesting correlations among the UHMWPE modifications, structural changes, and mechanical performance., Discussion: Surprisingly enough, UHMWPE materials from different manufacturers showed quite different properties, including the resistance against the long-term oxidative degradation, which is regarded as one of the main reasons of TJR failures. The most promising UHMWPE types were crosslinked materials with biocompatible stabilizers., Conclusions: Current UHMWPE liners from different manufactures used in total knee replacements exhibit significantly different structure and properties. From the point of view of clinical practice, the traditional UHMWPE types, which contained residual radicals from irradiation and/or gamma sterilization, showed inferior resistance to oxidative degradation and should be avoided. The best properties were observed in modern UHMWPE types, which combined crosslinking, biocompatible stabilizers, and sterilization by ethylenoxide or gas plasma., Key Words: UHMWPE; knee replacements; oxidative degradation; infrared spectroscopy; microhardness.

PURPOSE OF THE STUDY In clinical practice UHMWPE is the most commonly used material for manufacturing articular components of joint replacements. The purpose of this study is to find out whether repeated ethylene oxide sterilization results in oxidative degradation of UHMWPE or not and also whether the oxidative degradation of various types of ethylene oxide-sterilized UHMWPE depends on storage time or not. MATERIAL AND METHODS The set included 12 samples of UHMWPE (three samples with different modifications (virgin PE, with E vitamin and cross-linked with thermal treatment) and different number of sterilizations (0×-3×)). The set also included 8 samples of commercial components of hip or knee replacements sterilized with ethylene oxide and stored for different storage periods. The oxidative degradation was assessed by infrared microspectroscopy, based on which the oxidation index (OI), transvinylene index (VI), crystallinity index (CI) and E vitamin index (EI) were calculated. Mechanical properties of UHMWPE were obtained through microhardness measurements. Statistical processing of the results was performed. RESULTS In all the samples, very low oxidative degradation values were reported (most OI values < 0.1). All radiation crosslinked UHMWPE samples showed an increased VI index and a slightly lower crystallinity index. All unmodified samples (irrespective of whether or not and how many times or how long ago the samples were sterilized with EtO) had almost zero value of VI. Changes in crystallinity were negligible (in the rage of 0.56-0.63), which required very accurate measurements of micromechanical properties. Yet, linear correlation was established between microhardness and crystallinity. DISCUSSION All the mentioned indices changed as anticipated: OIs were very low and slightly increased with time of storage, VIs of radiation crosslinked samples grew in proportion to the total gama radiation dose, CIs decreased in samples thermally treated by remelting, and EIs were very low due to negligible concentration of stabiliser (0.1%) in the samples of medical grade UHMWPE. CONCLUSIONS All samples showed zero or minimum oxidative degradation. This confirmed that neither ethylene oxide sterilization, nor multiple EtO sterilization or longer storage of polymer after ethylene oxide sterilization result in major oxidative degradation. Key words: UHMWPE, ethylene oxide, sterilization, oxidation, infrared spectroscopy, microhardness.