Search

In the last decade, alginate-based microgels have gained relevant interest as three-dimensional analogues of extracellular matrix, being able to support cell growth and functions. In this study, core-shell microgels were fabricated by self-polymerization of dopamine (DA) molecules under mild oxidation and in situ precipitation of polydopamine (PDA) onto alginate microbeads, processed by electro fluid dynamic atomization. Morphological (optical, SEM) and chemical analyses (ATR-FTIR, XPS) confirmed the presence of PDA macromolecules, distributed onto the microgel surface. Nanoindentation tests also indicated that the PDA coating can influence the biomechanical properties of the microgel surfaces—i.e., σmaxALG = 0.45 mN vs. σmaxALG@PDA = 0.30 mN—thus improving the interface with hMSCs as confirmed by in vitro tests; in particular, protein adsorption and viability tests show a significant increase in adhesion and cell proliferation, strictly related to the presence of PDA. Hence, we concluded that PDA coating contributes to the formation of a friendly interface able to efficiently support cells’ activities. In this perspective, core-shell microgels may be suggested as a novel symmetric 3D model to study in vitro cell interactions.

In this work, the effect of different mixing techniques on thermal and mechanical properties of graphene nanoplatelets (GNPs) and graphene nanofibers (GANFs) loaded epoxy nanocomposites was investigated. Three dispersion methods were employed: a high shear rate (HSR), ultrasonication (US) and the fluidized bed method (FBM). The optical microscopy has revealed that the most suitable dispersion, in terms of homogeneity and cluster size, is achieved by implementing the US and FBM techniques, leading to nanocomposites with the largest increase of glass transition temperature, as supported by the DMA analysis data. The fracture toughness results show a general increase of both the critical stress intensity factor (KIC) and the critical strain energy release rate (GIC), likely due to the homogeneity and the low scale dispersion of the carbonaceous nanostructures. Based on the nanocomposite fracture toughness improvements and also assuming a potential large scale up production of the nanocomposite matrix, a single mixing technique, namely the FBM, was employed to manufacture the carbon fiber reinforced composite (CFRC). This method has resulted in being less time-consuming and is potentially most suitable for the high volume industrial production. The CFRCs were characterized in terms of tensile, flexural and interlaminar fracture toughness properties and the results were analyzed and discussed.

The aim of this paper is to study the effect of strain rate on the compressive behavior of the highly cross-linked RTM6 epoxy resin used in advanced aerospace composites. Dynamic compression tests were performed using a split Hopkinson pressure bar, along with reference quasi-static compression tests, to cover a strain rate range from 0.001 to 1035 s−1. Special attention was paid to the optimization of the test methodologies in order to obtain material data free of bias related to the use of different load introduction techniques and sample geometries over the considered strain rate range. In addition, the use of full-field 3D deformation measurements allowed the validation of traditional test and material assumptions. A novel self-alignment tool was developed to enable perfect interfacial contact during compression loading. The 3D digital image correlation technique was used to measure the instantaneous deformation of the sample during compression at different strain rates. Results showed a pronounced strain rate sensitivity of the RTM6 epoxy in compression. The peak yield strength increased with increasing strain rate, while the elastic modulus and Poisson’s ratio in compression were independent of the strain rate. The barreling of the sample in compression, quantified by the barreling ratio, showed an increase during the progression of the compression tests. However, the barreling ratio significantly decreased with the increasing strain rate. Finally, it was shown that neglecting the significant volume change in the yield stages gave rise to a non-negligible underestimation of the strength of the material.

This paper describes the preparation and characterization of poly(2,6-dimethyl-1,4-phenylene)oxide (PPO) highly porous monolithic aerogels with a hydrophobic nanoporous–crystalline phase and a hydrophilic sulfonated amorphous phase. The sulfonated aerogels were obtained by the sulfonation of PPO physical gels, followed by the supercritical CO2 extraction of solvents. WAXD and FTIR analysis showed that the nanoporous–crystalline phase was preserved for a degree of sulfonation up to c.a. 35%, allowing a highly volatile organic compound (VOC) sorption capacity. The sulfonated PPO aerogels exhibited a high water sorption capacity, with a water uptake of up to 500 wt%, and faster VOC sorption kinetics from water with respect to unsulfonated aerogels.