Search

Nowadays, with the mechanization of human societies, the demand for energy production and storage has also increased. Fossil fuels are running out, and thus, clean energy production using non-toxic and accessible sources is desirable. The valorization of waste materials into useful compounds is among the most important research subjects. Increasing interest in cost-effective raw materials and environmentally friendly precursors has brought agricultural residues up as promising, widespread biowaste all around the world. Rice husks (RHs), corn husks, wheat straws, sugarcane bagasse, fruit nut residues, and many other agricultural wastes have been broadly applied for designing novel materials, which can be applicable for energy conversion and storage. Agricultural waste contains useful chemical compounds, which may act as reducing, stabilizing, or capping agents, templates, precursors, etc., to produce various compounds viz. carbonaceous and (nano)materials. This review paper discusses the compounds that can be applicable for electrocatalytic applications for energy conversion in addition to energy storage. In fact, in this review, reports concerning agricultural waste-derived (carbon/nano)materials for energy conversion as well as energy storage devices such as different types of batteries, supercapacitors, and solar cell systems have been reviewed. The application of agricultural waste for energy conversion and storage is a very important issue due to the increase in the human population in the future, resulting in energy shortage problems. Therefore, suitable solutions must be developed for energy conversion and storage. On the other hand, the application of natural and environmentally friendly agricultural waste is very important for energy production and storage in addition to preventing the accumulation of this waste in the environment. [ABSTRACT FROM AUTHOR]

The capacity to produce exopolysaccharides (EPS) is well known among several microorganisms, especially lactic acid bacteria (LAB). However, the physiological role of these polymers has yet to be elucidated. Nevertheless, it has been observed that LAB growth conditions and adaptation to external environments and substrates are directly related to EPS biosynthesis. This study aimed to evaluate alternative carbon sources from agave by-products to synthesize EPS with LAB. Native LAB from the genera Lactococcus and Lactiplantibacillus were evaluated for their ability to produce EPS from simple carbon sources; they showed potential to produce EPS, presenting positive results on Congo red plates using glucose and fructose as carbon sources. In addition, native LAB could synthesize EPS from agave leaves and bagasse. L. plantarum ITD-ZC-107 stand out in the production of EPS, especially from bagasse. Thermostability of EPS from the evaluated carbon sources was analyzed. EPS from agave leaves and bagasse showed a higher degradation temperature than the ones obtained from glucose and sucrose, indicating better thermo-resistance. [Display omitted] • Native lactic acid bacteria produced exopolysaccharides from glucose and sucrose. • Exopolysaccharides were produced by lactic acid bacteria using agave by-products. • EPS from agave by-products showed high degradation temperatures. [ABSTRACT FROM AUTHOR]

Batik is a widely recognized form of clothing in Indonesian society. The batik-making process uses synthetic dyes, which can pollute the environment. This study aims to modify biochar derived from sugarcane bagasse using iron (Fe) synthesis. Biochar was produced through pyrolysis, while iron was sourced from beach sand in Glagah, Yogyakarta. The research involved four stages: (1) production of biochar from sugarcane bagasse, (2) modification of biochar with iron through beach sand synthesis, (3) application of iron-modified biochar (IMB) to methylene blue (MB), and (4) analysis of biochar characteristics. The results show that iron-modified biochar (IMB) affects biochar properties. IMB falls into the micropore category with a micropore surface area of 71.1%. The optimum wavelength was 571 nm with an adsorption level of 0.155. The application of IMB to batik wastewater demonstrated that adding 6% Fe and soaking for 180 minutes achieved the highest reduction in batik wastewater at approximately 69% with an R squared value (R²) of 0.975. Degradation of batik dye with 6% Fe using the Heterogeneous Fenton method resulted in yellow color degradation of 16%, fast green 3%, methylene orange 4%, red 3%, and methylene blue 23%. These findings highlight the potential of using sugarcane bagasse as a renewable resource for producing adsorbents that contribute to effective batik wastewater treatment. [ABSTRACT FROM AUTHOR]

The effect of increasing organic load on the specific methane yields (SMYs) and kinetics of methane production during the anaerobic digestion (AD) of sugarcane bagasse (SB) was investigated in batch experiments at 37 °C. The organic load of the batch AD system was increased based on an increase in the feed-to-inoculum (F/I) ratio (T1–T5) and increase in the Total Solids (TS)% of the working volume (T6–T10). The results show that in both the treatment sets, an increase in organic load led to a decrease in SMY. Higher organic loads in terms of F/I ratio (T4 and T5) were inhibited due to Volatile Fatty Acid (VFA) accumulation. On the other hand, higher organic loads (T8, T9 and T10) in terms of the higher TS% of the working volume was inhibited by the accumulation of NH4-N. Thus, an organic load of 50 gVS/L at an F/I ratio = 1.0 and TS = 10% (T3) was found to be the highest organic load that had no significant inhibitions among the tested treatments. The results from the kinetic studies show that the first-order kinetic model is the best fit for the SMY data, with average differences% of 2.32% and 3.13% for treatments T1–T5 and T6–T10, respectively. [ABSTRACT FROM AUTHOR]

Biomass ash is currently attracting the attention of science and industry as an inexhaustible eco-friendly alternative to pozzolans traditionally used in commercial cement manufacture (fly ash, silica fume, natural/calcined pozzolan). This paper explores a new line of research into Marabou weed ash (MA), an alternative to better-known conventional agro-industry waste materials (rice husk, bagasse cane, bamboo, forest waste, etc.) produced in Cuba from an invasive plant harvested as biomass for bioenergy production. The study entailed full characterization of MA using a variety of instrumental techniques, analysis of pozzolanic reactivity in the pozzolan/lime system, and, finally its influence on the physical and mechanical properties of binary pastes and mortars containing 10% and 20% MA replacement content. The results indicate that MA has a very low acid oxide content and a high loss on ignition (30%) and K2O content (6.9%), which produces medium–low pozzolanic activity. Despite an observed increase in the blended mortars' total and capillary water absorption capacity and electrical resistivity and a loss in mechanical strength approximately equivalent to the replacement percentage, the 10% and 20% MA blended cements meet the regulatory chemical, physical, and mechanical requirements specified. Marabou weed ash is therefore a viable future supplementary cementitious material. [ABSTRACT FROM AUTHOR]

The spectrum of enzymes required for complete lignocellulosic waste hydrolysis is too diverse to be secreted by a single organism. An alternative is to employ fungal co-cultures to obtain more diverse and complete enzymatic cocktails without the need to mix enzymes during downstream processing. This study evaluated the co-cultivation of Aspergillus brasiliensis and Trichoderma reesei RUT-C30 in different conditions using sugarcane bagasse as the carbon source. The resulting enzymatic cocktails were characterized according to the impact of strain inoculation time on enzymatic activities and proteome composition. Data revealed that the profile of each enzymatic extract was highly dependent on the order in which the participating fungi were inoculated. Some of the co-cultures exhibited higher enzyme activities compared to their respective monocultures for enzymes such as CMCase, pectinase, β-glucosidase, and β-xylosidase. Analysis of the T. reesei RUT-C30 and A. brasiliensis co-culture secretome resulted in the identification of 167 proteins, with 78 from T. reesei and 89 from A. brasiliensis. In agreement with the enzymatic results, proteome analysis also revealed that the timing of inoculation greatly influences the overall secretome, with a predominance of T. reesei RUT-C30 proteins when first inoculated or in simultaneous inoculation. [ABSTRACT FROM AUTHOR]

Boron is a naturally occurring trace chemical element. High concentrations of boron in nature can adversely affect biological systems and cause severe pollution to the ecological environment. We examined a method to effectively remove boron ions from water systems using sugarcane bagasse biochar from agricultural waste with NH3 nanobubbles (10% NH3 and 90% N2). We studied the effects of the boron solution concentration, pH, and adsorption time on the adsorption of boron by the modified biochar. At the same time, the possibility of using magnesium chloride and NH3 nanobubbles to enhance the adsorption capacity of the biochar was explored. The carbonization temperature of sugarcane bagasse was investigated using thermogravimetric analysis. It was characterized using XRD, SEM, and BET analysis. The boron adsorption results showed that, under alkaline conditions above pH 9, the adsorption capacity of the positively charged modified biochar was improved under the double-layer effect of magnesium ions and NH3 nanobubbles, because the boron existed in the form of negatively charged borate B(OH)4− anion groups. Moreover, cations on the NH3 nanobubble could adsorb the boron. When the NH3 nanobubbles with boron and the modified biochar with boron could coagulate each other, the boron was removed to a significant extent. Extended DLVO theory was adopted to model the interaction between the NH3 nanobubble and modified biochar. The boron adsorption capacity was 36 mg/g at room temperature according to a Langmuir adsorption isotherm. The adsorbed boron was investigated using FT-IR and XPS analysis. The ammonia could be removed using zeolite molecular sieves and heating. Boron in an aqueous solution can be removed via adsorption with modified biochar with NH3 nanobubbles and MgCl2 addition. [ABSTRACT FROM AUTHOR]

Sugarcane bagesse was utilised as a low-cost adsorbent for the removal of metal ions. The study was done at a temperature of 35°C, and the maximum adsorption capacities for Pb(II) and Cd(II) ions were 3.02 and 2.90 mg/g, respectively, for sugarcane bagasse. These results were determined using the following optimum conditions: initial metal ion concentration of 100 mg/dm3, adsorbent weight of 0.5 g, time of 30 min and pH of 6. The adsorption of the metal ions by the adsorbents decreased with an increase in the initial concentration of the metal ions in an aqueous solution. The rate of adsorption also increased with temperature. The adsorption showed a good fit to the Langmuir model compared to the Freundlich adsorption model. The Langmuir dimensionless constant (RL) for the adsorption of Pb(II) ion and Cd(II) ion ranged from 0.081 to 0.123 and 0.115 to 0.172, respectively, which confirms favourable adsorption. The adsorption process showed that the pseudo-second-order kinetics was a better fit than the pseudo-first-order kinetics. The result of this work showed a low-cost and efficient potential of sugarcane bagasse to be employed as a good adsorbent for metal ion removal. [ABSTRACT FROM AUTHOR]

Sugarcane bagasse is an agro-waste that could replace timber resources for the production of bio-composites. Composite boards such as particleboard offer an issue for the use and recycling of poor quality timber, and these engineered products can overcome some solid wood limitations such as heterogeneity and dimension. Bagasse offers an alternative to wood chips for particleboard production but present some disadvantages as well, such as poor physico-mechanical properties. To address these issues, bagasse fibers were treated with an innovative natural resin formulated with tannin and furfural. Impregnated particles with different concentrations of resin (5%, 10%, and 15% m/m) were exposed to temperatures of 40°C, 60°C, 80°C, and 100°C for resin curing. Various types of tannin-based adhesives, including tannin formaldehyde, tannin/formaldehyde-furfural, and tannin hexamine, were utilized for bonding the treated bagasse particles. The resultant panels were assessed for their physical and mechanical properties and compared to those produced using Melamine-Urea-Formaldehyde (MUF) adhesive. The density of the panels varied from 650 to 730 kg/m3 depending on the resin concentration. The values for both modulus of elasticity and modulus of rupture increased as the resin concentration increased. The internal bonding values exhibited an increase with resin concentration up to a critical point, after which a decreasing trend was observed. The water absorption and thickness swelling were significantly reduced with an increase in resin concentration. However, the panels produced using MUF adhesive yielded the most favorable physico-mechanical properties. Additionally, the panels made with tannin-based adhesives met the minimum requirements specified in the standard EN 312 (specifications for uncoated resin-bonded particleboards) for application in dry conditions. The analysis of formaldehyde emissions indicated that panels produced with tannin-based adhesives exhibited significantly lower emissions compared to those made with MUF. The tannin/furfural resin showed great potential for improving the quality of bagasse particleboard using tannin-based adhesives. [ABSTRACT FROM AUTHOR]

Copyright of China Forest Products Industry is the property of China Forest Products Industry Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Milling pretreatment is a crucial step in the bioconversion of lignocellulosic biomass such sugarcane bagasse because it facilitates access to cellulose for subsequent chemical treatments. However, most experiments have been conducted at the laboratory scale, where it has been identified that high energy is required for the processing of biomass. For this reason, it is proposed to implement the screw extruder technique for the processing of cellulose. This article focuses on the characteristics, types, and applications of milling pretreatment for sugarcane bagasse, with a particular emphasis on its role in lignin removal and the milling design. Milling pretreatment reduces the particle size of lignocellulose biomass through compression shear and tearing mechanisms, which enhances the accessibility of cellulose and hemicellulose to enzymes and chemicals, thereby improving the efficiency of bioconversion processes. Innovative mathematical modeling, a mechanical design in a CAD application, and an FEA analysis of the milling pretreatment equipment are presented, providing insights into the design and optimization of milling pretreatment processes. This article presents an innovative potential system for milling pretreatment in sugarcane bagasse for the production of bioethanol, heat and power, and other value-added products, contributing to a more sustainable and circular economy. [ABSTRACT FROM AUTHOR]

Copyright of Journal of Beijing University of Technology is the property of Journal of Beijing University of Technology, Editorial Department and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Introduction: The fruit wastes, in particular agricultural wastes, are considered potential and inexpensive sources of bioactive compounds. Objective: The current study was aimed at the preparation of an optimized extract of sugarcane bagasse using microwave‐assisted extraction (MAE) technology and comparative evaluation of chemical composition, antioxidant, and antidiabetic activities with extract prepared through maceration technique. Methodology: Box–Behnken Design (BDD) with response surface methodology was applied to observe interactions of three independent variables (ethanol concentrations [%], microwave power [W], and extraction time [min]) on the dependent variables (total phenolic content [TPC] and antioxidant status via 2,2‐diphenyl‐1‐picrylhydrazyl [DPPH] to establish optimal extraction conditions. The ultra‐high performance liquid chromatography‐quadrupole time‐of‐flight mass spectrometry (UHPLC‐Q‐TOF‐MS) analysis was applied for untargeted metabolite profiling, and in vitro assays were used for evaluation of the antidiabetic and antioxidant potential of the extract. Moreover, an in silico study was used to predict the interaction of five dominant compounds from the UHPLC‐Q‐TOF‐MS profile against the dipeptidyl peptidase‐IV (DPP‐IV) enzyme. Results: The optimal conditions for the extraction were established at 60% (v/v) ethanol, 500 W microwave power, and 5 min time with TPC 12.83 ± 0.66 mg GAE/g d.w. and DPPH 45.09 ± 0.07%. The UHPLC‐Q‐TOF‐MS analysis revealed the presence of a total of 106 compounds in the extract. Moreover, the extract prepared through MAE technology presented higher TPC and DPPH findings than the extract prepared through maceration. Similarly, the extract was also found with good antidiabetic activity by inhibiting the DPP‐IV enzyme which was also rectified theoretically by a molecular docking study. Conclusion: The current study presents a sustainable and an optimized approach for the preparation of sugarcane bagasse extract with functional phytoconstituents and higher antidiabetic and antioxidant activities. Box‐Behnken design was employed to determine the optimal microwave conditions for the preparation of sugarcane bagasse extract. The optimized batch was obtained by using 60% ethanol concentration, 500 W microwave power, and 5 min time. The extract exhibited high TPC, DPPH activity and 106 compounds in UHPLC‐Q‐TOF‐MS analysis. It showed potent antidiabetic activity by inhibiting DPP‐IV enzyme, confirmed by molecular docking. The MAE extract was found with higher TFC contents and antioxidant activity than the extract prepared by maceration technique. [ABSTRACT FROM AUTHOR]

Local agro-industrial wastes-based particleboards and fiberboards in Egypt are manufactured mainly from sugarcane-bagasse and flax shives. These panels are used in decorations and interior claddings. This paper aimed to broaden their market to be utilized in local low-cost and simple building envelope retrofitting packages instead of conventional packages that depend on imported expanded polystyrene and wet-rendered gypsum boards. Thermal conductivities of various existing sugarcane-bagasse and flax-shives-based panels were measured to be used in developing multilayered interior claddings with adequate thermal insulating performance to increase the thermal mass of a validated non-insulated case-study residential building as recommended by the Egyptian Code for Energy Efficiency of Residential Buildings. Models retrofitted using the developed cladding assemblies were simulated using Design Builder to determine their achieved annual energy savings and predict their profitability. Thermal conductivities of sugarcane-bagasse and flax-shives-based particleboards were lower than wood-based cladding panels, with the range of 0.05-0.1166 W/mK. Moreover, the thermal conductivities of sugarcane-bagasse fiberboard had the range of 0.0926-01,111 W/mK which is significantly lower than wood-based fiberboards. Simulation results showed that both models retrofitted, sugarcane bagasse-based and flax shives-based, achieved better energy savings, 5.07% and 5.04%, than the conventionally retrofitted model, 3.73%. Furthermore, the flax-shives-based model showed higher profitability, with positive income achieved in the 15th year, than a conventionally retrofitted model, achieved in the 20th year, and the sugarcane-bagasse-based model, achieved in the 19th year. Thus, it was recommended that although flax-shives-based wall claddings were usually 14-20% thicker than sugarcane-bagasse-based claddings, they provided similarly high annual energy savings with lower initial costs and higher profitability. [ABSTRACT FROM AUTHOR]

The increased use of sugarcane bagasse in electricity production has led to a significant rise in the dumping of sugarcane bagasse ash (SCBA). To study the efficiency of SCBA as a in the production of alkali-activated binders (AABs), which consist of quarry dust and crushed sand as fine aggregates, the present study investigates the influence of different activators, namely NaOH-Na2SiO3 and KOH-K2SiO3, and the effect of curing type (ambient and heat curing) on the mechanical and durability properties of quarry dust-SCBA incorporated AAB. Various tests, including compressive strength, water absorption, sorptivity, and sulphate resistance, along with X-ray diffraction and scanning electron microscopy were conducted for AAB characterization. The results revealed that the addition of 20% quarry dust as an alternative to crushed sand in AAB is found to be optimum. The ambient-cured SCBA-blended AAB specimens demonstrated superior performance compared to their heat-cured counterparts. The Na-based SCBA blended AABs outperformed K-based AABs in resisting compressive strength reduction. The compressive strength of 28 days ambient cured Na-based and K-based AABs were found to be 47.8 and 32.4 MPa, respectively. Microstructural analysis revealed that the main hydration products in Na-based AAB are C-A-S-H, C-S-H, and N-A-S-H, while in K-based AAB, the main hydration products were found to be C-A-S-H, C-S-H, and K-A-S-H, respectively. The AAB mixtures consisting 10% SCBA found with superior performance compared to other SCBA blended AABs. However, excessive SCBA usage weakened the microstructure in both Na-based and K-based AABs. The findings demonstrate the potential for utilizing waste materials, such as SCBA and quarry dust, in the development of eco-friendly and high-performance alkali-activated binders, contributing to the reduction of environmental impact caused by the construction industry. [ABSTRACT FROM AUTHOR]

The use of sustainable energy sources is an alternative for fossil fuels, which can represent a positive factor to alleviate many current environmental issues. In that sense, not only sustainable industrial development is important, but also sustainable practices at the local level, including households. Specifically, heating and cooking are one of the most important activities that require energy in households, where the role of biomass could be of interest, as it can provide an energy source with lower environmental impact. However, there is room for improvement in biomass stoves, whose adaptability to specific wastes, as well as their improvement in efficiency, should be accomplished. The aim of this work was to assess the improvement of combustion performance of a domestic stove by the implementation of a programmable logic converter for a better adaptation to different biomass samples (holm oak, pear tree, poplar, and sugarcane bagasse pellets). This work provides further information about the current working protocol, being an alternative for better approaches that could be implemented in future works. Thus, the working regime of the stove was controlled, especially concerning the screw conveyor (to regulate pellet feeding) and flue gas fan (to change oxygen supply). As a result, better combustion performances were obtained, with heat capacities from 5.66 to 8.67 kW for the selected samples. Also, thermal capacities of the stove (1.43, 1.60, 2.22, and 1.83 kW for holm oak, pear tree, poplar, and sugarcane bagasse, respectively) were obtained, with a better combustion performance compared to previous studies (1600 and 120 ppm peak emissions for CO and NOx, respectively, and 15% as the lowest O2 concentration). On the other hand, different improvements of the combustion stove to avoid blockages, for instance, are proposed as further steps. [ABSTRACT FROM AUTHOR]

In this work, the phase inversion approach is used to synthesize a blended mixed matrix membrane from cellulose acetate polymer and sugarcane bagasse biochar. The experiments were carried out to estimate the extent of chlorpyrifos (CPS) pesticide removal. The results showed that the removal rate was more than 99% in making the filtered water suitable enough for domestic use. The physical and functional characteristics of the membranes, such as permeability, and contact angle were identified. The changes in the membrane characteristics were observed using scanning electron microscopy, Fourier transform infrared spectroscopy, and X-ray diffraction both before and after the experimental trials. Experiments were conducted to assess not only the rejection characteristics of CPS, as a function feed concentration, but also the effect co-ions on the rejection used to analyze the composition both before and after filtration. The effects of initial CPS concentration, biochar loading, and co-ions on the membrane were investigated. The membranes showed contact angles between 70° and 97° and a permeability between 0.25 × 1010 m Pa−1 s−1 and 0.31 × 1010 m Pa−1 s−1. The effective removal of CPS from the contaminated aqueous stream was attributed to a combination of adsorptive uptake and membrane-based separation. CPS was found to get adsorbed onto the membrane matrix through an intraparticle diffusion mechanism along with an irreversible monolayer adsorption. The membrane-solute adsorptive interaction was represented by Langmuir isotherm and intraparticle diffusion models with a maximum adsorption capacity of 192.3 mg g−1. The findings indicated the efficacy of biochar-cellulose acetate mixed matrix membrane for sustainable and eco-friendly treatment of chlorpyrifos contaminated water. [ABSTRACT FROM AUTHOR]

Bagasse ash (BA) is an agricultural waste obtained from power plants using sugarcane bagasse as an energy source. Although BA is successfully used as a building material, its application in the polymer industry remains challenging due to the lack of surface reactivity. In this study, BA was purified and named PBA before being incorporated into acrylonitrile butadiene rubber (NBR). Tannic acid (TA), a naturally occurring plant polyphenol, was used as a surface‐modifying agent for improved interfacial interaction. The effect of TA content on the properties of PBA‐filled NBR was investigated. The results showed that the presence of TA resulted in cure retardation, i.e., the scorch time, cure time, and activation energy of the vulcanization reaction increased with increasing TA content. However, the increase in TA content enhanced a rubber‐filler interaction, as evidenced by the considerable increase in bound rubber content. Such an enhancement resulted in the improvement of certain mechanical properties, including hardness, modulus, tensile strength, and tear strength. This research showed that tannic acid can be used as a surface‐modifying agent in NBR/PBA composites. [ABSTRACT FROM AUTHOR]

Introduction: The drilling industry is one of the main sectors of the oil industry, and oil drilling is one of the most specialized industrial activities. Large-scale production of sugarcane bagasse in Khuzestan Province creates an environmental opportunity to utilize this agricultural byproduct in different sections as a valuable byproduct. This study aimed to investigate the ability of the raw form of bagasse and its transformed structure in heavy metal fixation in drilling mud and to investigate the efficiency of crude bagasse, processed bagasse, and biochar adsorbents in removing heavy metals from the drilling mud residues of Ahvaz oil field. Methods: Sampling of drilling mud waste from Mishan Geological Formation (MGF) and Aghajari Geological Formation (AGF) was done on a vibrating sieve. The treatments examined in this research include the contact time in six levels (30, 60, 90, 120, 150, and 180 min), amount of the adsorbent in three levels (0.1, 0.5, and 1 g), adsorbent type in three levels (crude bagasse, processed bagasse, and biochar), and the formation type in two levels (Aghajari and Mishan). After chemical digestion, the samples were placed in contact with crude bagasse, processed bagasse, and biochar according to the designed conditions. Then, the removal percentages of Ba, Ni, V, Cd, Fe, and Pb were calculated. Means were compared using Duncan's test at the 1% level. Results and Discussion: The results showed that the biochar adsorbent is the most efficient compared to other adsorbents. The maximum removal percentages of heavy metals Ba, Ni, V, Cd, Fe, and Pb by crude bagasse are 72.53%, 68.89%, 79.49%, 76.88%, 49.42%, and 85%, respectively. In addition, the results showed that the maximum removal percentages of heavy metals Ba, Ni, V, Cd, Fe, and Pb by crude bagasse are 81/72%, 83/89%, 86/67%, 83/44%, 64/41%, and 90.72%, respectively. The maximum efficiency of biochar for adsorbing heavy metals Ba, Ni, V, Cd, Fe, and Pb is 90.70%, 91.84%, 88.89%, 88.75%, 78.59%, and 97.75%, respectively. The maximum amount of heavy metals adsorbed by all adsorbents was 1 gr/L, and the adsorption efficiency increased by increasing the amount of the adsorbent from 0.2 to 1 gr/L. In examining the effect of contact time, the maximum removal percentage of heavy metals barium and cadmium was obtained in 120 min, nickel and lead in 90 min, and vanadium and iron in 60 min. After the above contact times, there was no increase in the maximum percentage of metal removal. [ABSTRACT FROM AUTHOR]

This study investigated the effects of using bagasse ash (BA) and metakaolin (MK) together as substitutes for cement in self-compacting concrete (SCC), together with the addition of glass fiber (GF), on the physical and mechanical characteristics of concrete. Eighteen SCC mixes were created, each containing different proportions of BA (0%, 10%, 15%, and 20%), MK (0%, 10%, 15%, and 20%), and BA and MK collectively (10% + 5% and 10% + 10%) as cement replacements with and without 0.1% GF. Using the results of the slump flow, T500 slump flow, V-funnel, and L-box tests, the performance of fresh SCC was determined. Furthermore, this study evaluated the strength, durability, and microstructural properties of the SCC samples. The SCC mix blended with 10% BA and 5% MK revealed better flowability as the slump flow increased from 692 mm to 715 mm. A strong linear correlation was discovered between the slump flow values (mm) and V-funnel duration (sec) and blocking ratio (H2 /H1 ) with R² = 0.8876 and R² = 0.8467, respectively. Of all test mixes, the SCC mix blended with 10% BA, 5% MK, and 0.1% GF (SCC1B10M5) demonstrated the highest degree of strength. At 56 days, the 10% BA, 5% MK, and 0.1 GF mix had 12.8%, 25.7%, and 22.2% higher compressive, flexural, and splitting tensile strengths than the control mix, respectively. SCC, combined with BA, MK, and GF, outperformed the control mix. After immersion in a 3% H2SO4 solution, the SCC mix having 10% BA, 5% MK, and 0.1% GF experienced a minimum reduction in weight loss and ultrasonic pulse velocity of 1.01% and 3.1%, respectively. Additionally, there was a decrease of 29.4% in the percentage of charges passed. The ideal composition was achieved by incorporating 10% BA, 5% MK, and 0.1% GF into the SCC mixture, resulting in a dense structure without any visible pores or cracks during the microstructural analysis. [ABSTRACT FROM AUTHOR]

Plastic is a material that is often used as a storage medium, equipment and also furniture to support human activities, but plastic is not easily broken down by the environment. Bioplastic technology is one of the efforts made to address the problem of plastic packaging which can pollute the environment. Environmentally friendly plates, bioplastic products made from tapioca, glycerol and sugar cane bagasse. This research aims to determine the effect of variations in the size of bagasse on tensile strength, elongation at break, water resistance and biodegradability of environmentally friendly plates and to obtain the best formulation of varying sizes of bagasse as raw material for making environmentally friendly plates. This research used a Completely Randomized Design (CRD) with one factor, namely variation in the size of the bagasse. The results of this research show that there is a real influence between tensile strength, water resistance and biodegradability, however, in the elongation test, variations in bagasse did not have a significant effect. Tensile strength values range from 20.00 N/mm2 to 47.72 N/mm2. The largest elongation value is 4.08%. The highest water resistance is at room temperature, namely 88.86% with a degree of curvature of 16° and in water with a temperature of 60°C, namely 85.02% with a degree of curvature of 18.75°. Variations in the size of bagasse also affect the biodegradability of environmentally friendly plates which ranges from 11.77% to 14.65%. The best treatment is a sample with a variety of bagasse sizes of 60 mesh, because it has high strength compared to other samples. [ABSTRACT FROM AUTHOR]

A validated rapid high-performance liquid chromatography (HPLC)-refractive index (RI) method was developed for the identification and quantification of glucose and xylose in hydrolyzed bagasse extract. The separation of compounds was achieved on Eurokat® H column (300 × 8 mm, 10 μm) at 75°C, using 0.01 N sulfuric acid solution as mobile phase and 0.6 mL/min as flow rate. The method was validated based on accuracy, precision, linearity, robustness, uncertainty, limit of detection (LOD) and limit of quantification (LOQ). Total chromatographic analysis time per sample was ~11 min. Calibration plots were linear over the concentration ranges 11–100 μg/100 μL for glucose and xylose. The LOD was 0.8 ppm and LOQ was 2.5 ppm. The high recovery and low relative standard deviation confirm the suitability of the method for determination of glucose and xylose in bagasse extract. The proposed HPLC-RI method was accurate, fast and robust and required less run time due to less analytes retention times and allowed optimal energy consumption owing to lower column oven temperature. [ABSTRACT FROM AUTHOR]

The aim of this research was to separate the over-the-counter nonsteroidal anti-inflammatory drug (NSAID), ibuprofen, from an aqueous solution using the adsorption method, as this NSAID is one of the most globally consumed. An adsorbent was crafted from the Agave angustifolia bagasse, a byproduct of the bacanora industry (a representative alcoholic beverage of the state of Sonora, in northwestern Mexico). Three bioadsorbents (BCT1, BCT2, and BCT3) were produced via pyrolysis at a temperature of 550 °C, with slight variations in each process for every bioadsorbent. The bioadsorbents achieved material yields of 25.65%, 31.20%, and 38.28% on dry basis respectively. Characterization of the bagasse and adsorbents involved scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The biomass morphology exhibited a cracked surface with holes induced via the bacanora production process, while the surface of the bioadsorbents before ibuprofen adsorption was highly porous, with a substantial surface area. After adsorption, the surface of the bioadsorbents was transformed into a smoother grayish layer. The macromolecules of cellulose, hemicellulose, and lignin were present in the biomass. According to functional groups, cellulose and hemicellulose degraded to form the resulting bioadsorbents, although traces of lignin persisted after the pyrolysis process was applied to the biomass. In an adsorption study, BCT1 and BCT2 bioadsorbents successfully removed 100% of ibuprofen from aqueous solutions with an initial concentration of 62.6 mg/L. In conclusion, the biocarbon derived from Agave angustifolia bagasse exhibited significant potential for removing ibuprofen via adsorption from aqueous solutions. [ABSTRACT FROM AUTHOR]

Organic solid waste treatment is crucial for enhancing environmental sustainability, promoting economic growth, and improving public health. Following our previous organic solid waste upgrading technique, a further two-step pilot-scale run, using sugarcane bagasse as the feedstock, has been successfully conducted with long-term stability. Firstly, the sugarcane bagasse was treated under mild conditions (400 °C and 1 bar of CH4), and this catalytic Methanolysis treatment resulted in a bio-oil with a yield of 60.5 wt.%. Following that, it was subjected to a catalytic Methano-Refining process (400 °C and 50 bar of CH4) to achieve high-quality renewable fuel with a liquid yield of 95.0 wt.%. Additionally, this renewable fuel can be regarded as an ideal diesel component with a high cetane number, high heating values, a low freezing point, low density and viscosity, and low oxygen, nitrogen, and sulfur contents. The successful pilot-scale catalytic upgrading of sugarcane bagasse further verified the effectiveness of this methane-assisted organic solid waste upgrading technique and confirmed the high flexibility of this innovative technology for processing a wide spectrum of agricultural and forestry residues. This study will shed light on the further valorization of organic solid waste and other carbonaceous materials. [ABSTRACT FROM AUTHOR]

High early-strength concrete and geopolymer offer advantages of faster construction and require less curing time than traditional concrete. Bagasse ash (BA), an inert pozzolan with low reactivity in alkaline media, was activated with 10M NaOH to enhance its porosity and surface area. It was then incorporated into an 80:20 wt% mixture of metakaolin (MK) and BA to improve the early-strength properties of geopolymers. This study investigates the effects of varying amounts of activated bagasse ash (ABA) on the physical and mechanical properties of a binary MK-BA-based geopolymer. The pozzolan-to-alkali ratio was maintained at 1:1, with a difference of 10M NaOH-to-Na2SiO3. The results indicated that the compressive strength of formulation with 50 wt% ABA increased by approximately 33% compared with formulation without ABA. XRD analysis showed a sodium aluminum silicate peak at 3 days, which decreased after 28 days, confirmed by SEM/EDS. The transformation of sodium aluminosilicate gel into a dense geopolymer matrix was observed, with IR spectra demonstrating the presence of Si–O-(Si/Al) bonds contributing to high compressive strength formulations. Overall, the ABA led to the early formation of the geopolymer 3D network with high compressive strength values. [ABSTRACT FROM AUTHOR]

Noise pollution is ranked as the third environmental pollution that can interfere with communication, recreation, or concentration. Hence, choosing the best materials could be one way to resolve a sustainable solution for noise pollution problems. Materials like bagasse are suitable composite materials for construction. Its natural fiber properties exhibit a good absorber characteristi c that would be used for acoustics barriers. Thus, this study aimed to investigate the sound absorption of bagasse using the twomicrophone transfer function method. Using two different thicknesses for the samples, 2.0 cm and 4.0 cm, the measured sound absorption coefficients were considerably higher than the conventional concrete. The measurements revealed that the 4.0 cm samples exhibited better sound absorption behavior between the two thicknesses, having a noise reduction coefficient (NRC) of 40% to 80%. It can be noted that it has shown consistency in the energy absorption throughout the frequency range of 250 Hz - 3000 Hz. Meanwhile, for the 2.0 cm-thickness samples, bagasse's performance is less absorptive from 250 Hz-1000 Hz but becomes more absorptive as it goes to higher frequencies with a peak value of approximately 95%. Also, the material's density and the sample's thickness influence the measured sound absorption coefficients. The result implies that bagasse, a green waste, can be a suitable candidate for acoustic building applications. Its advantages included low-cost materials from renewable sources, non-toxicity, and comparably high performance compared to standard or commercial products. These types of barriers can positively impact the noise level in the areas. [ABSTRACT FROM AUTHOR]

The aim of present work is to evaluate pyrolysis characteristics of poly(methyl methacrylate) (PMMA) and its blends with sugarcane bagasse (SB) contents of 10 and 20 mass % for the purpose of exploring the effect of SB on pyrolysis of PMMA. Non-isothermal pyrolysis determinations of three PMMA samples were performed thermogravimetrically and the initial pyrolysis temperatures of two PMMA blends are significantly lower than that of pure PMMA while the main pyrolysis shifts to higher temperature range. Using model-free isoconversional methods, pyrolysis activation energies calculated are varying within 71.7 ~ 154.0, 107.8 ~ 192.0 and 121.3 ~ 171.0 kJ·mol−1 for PMMA and its 10 or 20 mass % SB blends, respectively. The added SB turns to increase the activation energy of PMMA and thus make pyrolysis of PMMA become more arduous to accomplish. With the model-fitting method, the order-based F2/3, F3 and F3 chemical reaction models are found to be the most appropriate pyrolysis mechanisms for PMMA and its 10 or 20 mass % SB blends, respectively. Accordingly, their pre-exponential factor values are estimated to separately span in the range of 3.23 × 104 ~ 1.76 × 1011, 3.52 × 108 ~ 7.63 × 1016 and 1.55 × 1010 ~ 1.13 × 1015 min−1. The findings acquired from present work can provide necessary information for performing potential pyrolysis designs of PMMA and its biomass blended wastes. [ABSTRACT FROM AUTHOR]

Lignocellulosic biomass is a crucial renewable energy source for producing biofuels and valuable compounds, making it an attractive alternative to fossil resources. In this study, an environmentally friendly method was developed for cellulose fractionation from sugarcane bagasse using deep eutectic solvents (DESs), focusing on achieving high cellulose purity and specific physicochemical properties. The effects of different parameters were investigated by comparing four DESs: choline chloride–lactic acid (ChCl-LA), choline chloride–glycerol (ChCl-G), choline chloride–urea (ChCl-U), and choline chloride–polyalcohol (ChCl-P), under various reaction temperatures and times. The fractionation process was conducted under standard conditions at a temperature of 100 °C for 120 min with a 1:1 molar ratio. The results indicated that all DESs produced comparable cellulose recovery, ranging from 91.83% to 97.07%. A relatively high cellulose recovery was observed in the presence of ChCl-LA, at 95.47%. In addition, ChCl-LA demonstrated the highest efficiency in removing hemicellulose and lignin, at 95.36% and 93.38%, respectively, and high recovery yields of 70.45% for hemicellulose, and 70.66% for the lignin fraction. The fractionation conditions were further optimized using response surface methodology (RSM), achieving a ChCl-LA ratio of 1:2 v/v at 120 °C for 120 min. This resulted in impressive yields: 97.86% cellulose recovery, 96.50% hemicellulose removal, 74.40% hemicellulose recovery, 77.3% lignin recovery, and 71.5% lignin yield from sugarcane bagasse. These results closely match the predicted values, emphasizing the effectiveness of the process and its potential for economic application in lignocellulosic biorefinery operations. [ABSTRACT FROM AUTHOR]

Bagasse and straw are the two feedstocks used to produce cellulosic ethanol from sugarcane. Although this technology is advancing commercially, the differentiation between bagasse and straw remains elusive. This work investigates bagasse and straw supply, conditioning, and pretreatment in a pilot-scale steam-explosion continuous reactor (~ 10 kg/h feed) to illuminate the critical feedstock differences for process scale-up. Evaluating biomass across four sequential harvest seasons (2018–2021) shows that straw supplied in bales requires extra conditioning to reduce mineral matter and particle size before feeding into the reactor. Moreover, straw composition is more variable and consistently has lower contents of glucan (35.6–38.8%) and carbohydrate potential (glucose + xylose, 649–704 kg/dry tonne) compared to bagasse (40.8–42.9%; 735–760 kg/dry tonne). Biomass pretreatments without (190 °C, 5–15 min) and with sulfuric acid catalyst (149–170 °C; 5–15 min; 0.5–5.12%, m/m) show that straw differs from bagasse by presenting a higher acid neutralization capacity and about 5% of labile glucans. These results suggest that straw crushing and aqueous pre-extraction are promising strategies to reduce the dissimilarities with bagasse, thus facilitating the development of feedstock-agnostic biorefining. [ABSTRACT FROM AUTHOR]

Two α-arabinofuranosidases from the fungus Chrysoporthe cubensis COAD 3356 were partially purified, identified, characterized, and applied to the sugarcane bagasse saccharification to evaluate the potential of these enzymes to increase the sugar production from lignocellulosic biomass. The α-arabinofuranosidases were classified on GH51 (α-Ara1) and GH54/CBM42 (α-Ara2) families. After sugarcane bagasse saccharification, using the commercial cellulase-rich cocktail supplemented with α-Ara2 (15 U/g), there was an increase of 1.6, 3.9, and 6.1 times in the release of glucose, xylose, and arabinose, respectively. On the other hand, there was no increase in sugar release with α-Ara1 supplementation under the same saccharification conditions. The enzymes presented maximum activity at pH 4.0, and 60 °C. Both α-Ara1 and α-Ara2 were thermostable at 50 °C, presenting half-life values of 68 and 77 h, respectively. The enzyme α-Ara2 presented higher KMapp for synthetic substrate ρNP-α-arabinofuranoside (1.38 mmol/L) and wheat arabinoxylan (1.28 mmol/L) when compared with α-Ara1. A new fungal α-arabinofuranosidase structure, still little described in the GH51 family, was predicted. Furthermore, the results indicated that α-Ara2 is a promising molecule to be used to supplement cocktails for lignocellulose degradation. [ABSTRACT FROM AUTHOR]

Researchers are developing new techniques for clean fuel production due to environmental problems such as global warming. In this respect, bioethanol is considered among the most important renewable fuels. This study aims to investigate the energy cycle and estimate the potential environmental effects of ethanol production from sugarcane bagasse in Iran. To this end, ethanol's life cycle assessment (LCA) was conducted based on the "cradle to gate" approach. This assessment includes three stages of sugarcane farming, transportation to the factory, and bioethanol production. This study defines three scenarios for bioethanol production from sugarcane bagasse using the fermentation conversion process: fermentation, bagasse burning for electricity, and combined bioethanol and electricity production. The third scenario was chosen as the best. However, in environmental analysis, it showed the most negative effects on environmental indicators, especially in cases of abiotic depletion and global warming potential. Scenario 1 showed better results than the others. The results showed that electricity, diesel fuel, and nitrogen fertilizer had the greatest environmental impact in the mentioned process. Moreover, by replacing fossil fuels with clean energies, more energy efficiency and less environmental consequences can be achieved because fossil fuels cause air pollution leading to acid rain, eutrophication, damage to forests, and harm to wildlife. Our results show that the bioethanol production process using sugarcane bagasse as feedstock requires 27.13 MJ/L input energy, while the total output energy is 40.44 MJ/L. Energy indices were calculated, with values of 1.49, 0.037, 27.13, and 13.31 for energy ratio, efficiency, intensity, and net energy addition, respectively. [ABSTRACT FROM AUTHOR]

The examination of fungal secretomes has garnered attention for its potential to unveil the repertoire of secreted proteins, notably CAZymes (Carbohydrate-Active enzymes), across various microorganisms. This study presents findings on categorizing the secretome profile of CAZymes by their function and family, derived from the filamentous fungus Trichoderma longibrachiatum LMBC 172. The cultivation was performed through submerged fermentation with three distinct carbon sources: sugarcane bagasse, tamarind seeds, and a control simulating hemicellulose containing 0.5% beechwood xylan plus 0.5% oat spelt xylan. The secretome analysis revealed 206 distinct CAZymes. Each carbon source showed particularities and differences. Of these, 89 proteins were produced simultaneously with all the carbon sources; specifically, 41 proteins using only the hemicellulose simulation, 29 proteins when sugarcane bagasse was used as a carbon source, and only 3 when tamarind seeds were used. However, in this last condition, there was a high intensity of xyloglucanase GH74 production, thus reaffirming the richness of xyloglucan in the constitution of these seeds. When evaluating the proteins found in two conditions, 18 proteins were shown between the simulation of hemicellulose and sugarcane bagasse, 11 proteins between the simulation of hemicellulose and tamarind seeds, and 15 proteins between sugarcane bagasse and tamarind seeds. Among the proteins found, there are representatives of different families such as glycosyl hydrolases (GHs) that cleave cellulose, hemicellulose, pectin, or other components; carbohydrate esterases (CEs); polysaccharide lyases (PLs); carbohydrate-binding modules (CBMs); and auxiliary activity enzymes (AAs). These results demonstrate the importance of analyzing CAZymes secreted by microorganisms under different culture conditions. [ABSTRACT FROM AUTHOR]

Activated carbons are commonly used for adsorption/depollution applications, but only a few studies are related to their lubricating properties. In order to investigate a new family of friction reducers, the tribological properties of biochars and derived activated carbons obtained from sugar cane bagasse are investigated. Activated carbons are obtained from either a physical (steam water) or chemical (with phosphoric acid) activation process. The tribological tests show that the activated carbons present very low friction coefficients, close to 0.08. The correlation of textural and tribological investigations shows that the specific surface area of the compounds as well as the microporous and mesoporous domain extensions are key parameters to optimize the friction reduction properties of activated carbons. The friction properties of the compounds are improved if the mesoporous domain extension is above 40% of the total porous volume. This study shows that local biomass waste valorization is possible and that sugar cane bagasse-derived activated carbons appear as interesting new friction reduction additives for lubricants. [ABSTRACT FROM AUTHOR]

This research proposes an efficient alternative for dehydrating cassava bagasse to address the inherent challenges in the handling, transportation, storage, and preservation of this agro–industrial residue generated in cassava starch production plants. This residue is characterized by high moisture retention, considerable volume, and hydrophilic nature, complicating conventional drying methods. This study evaluates the impact of emerging ultrasound (US) and pulsed electric field (PEF) technologies prior to convective drying to enhance the dehydration efficiency of cassava bagasse, aiming at its valorization and contributing to the sustainability of the cassava starch industry. The findings reveal that pretreatment with ultrasound (US) and pulsed electric fields (PEF) significantly reduces the drying time of cassava bagasse compared to convective drying alone. With probe ultrasound at 26 kHz for 30 min, the drying time is reduced by 72% (3.83 h vs. 14.0 h); with bath ultrasound at 37 kHz for 30 min, it is reduced by 56.0% (6.16 h vs. 14.0 h); and with PEF at 7.5 kV/cm for 30 min, it is reduced by 52.4% (6.66 h vs. 14.0 h). These emerging technologies increased the effective diffusivity and modified the molecular structure of the bagasse, thereby improving mass transfer and drying process efficiency. These results are particularly useful for developing more efficient and sustainable strategies for drying agricultural by-products, with direct implications for the post-industrial treatment of agro–industrial residues with high water content. [ABSTRACT FROM AUTHOR]

Xylanase is commonly thought to effectively cooperate with cellulase to promote the bioconversion of lignocellulose. In this study, a novel xylanase, SipoEnXyn10A (Xyn10A), previously identified from Streptomyces ipomoeae, was employed to investigate its synergetic effects on sugarcane bagasse (SCB) transformation. It was shown that the relative increase in reducing sugars reached up to 65%, with enhanced yields of glucose and xylose by 78% and 50%, respectively, in the case of the replacement of cellulase with an equivalent amount of Xyn10A at an enzyme loading of 12.5%. The highest degrees of synergy (DS) for glucose and xylose could reach 2.57 and 1.84. Moreover, the hydrolysis rate increased evidently, and the reaction time to reach the same yield of glucose and xylose was shortened by 72 h and 96 h, respectively. This study on synergistic mechanisms demonstrated that the addition of Xyn10A could cause the destruction of substrates' morphology and the dissolution of lignin components but could not change the accessibility and crystallinity of substrate cellulose. The joint effect of cellulase and xylanase during the hydrolysis process was thought to result in a synergistic mechanism. [ABSTRACT FROM AUTHOR]

The aim of this research was to separate the over-the-counter nonsteroidal anti-inflammatory drug (NSAID), ibuprofen, from an aqueous solution using the adsorption method, as this NSAID is one of the most globally consumed. An adsorbent was crafted from the Agave angustifolia bagasse, a byproduct of the bacanora industry (a representative alcoholic beverage of the state of Sonora, in northwestern Mexico). Three bioadsorbents (BCT1, BCT2, and BCT3) were produced via pyrolysis at a temperature of 550 °C, with slight variations in each process for every bioadsorbent. The bioadsorbents achieved material yields of 25.65%, 31.20%, and 38.28% on dry basis respectively. Characterization of the bagasse and adsorbents involved scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The biomass morphology exhibited a cracked surface with holes induced via the bacanora production process, while the surface of the bioadsorbents before ibuprofen adsorption was highly porous, with a substantial surface area. After adsorption, the surface of the bioadsorbents was transformed into a smoother grayish layer. The macromolecules of cellulose, hemicellulose, and lignin were present in the biomass. According to functional groups, cellulose and hemicellulose degraded to form the resulting bioadsorbents, although traces of lignin persisted after the pyrolysis process was applied to the biomass. In an adsorption study, BCT1 and BCT2 bioadsorbents successfully removed 100% of ibuprofen from aqueous solutions with an initial concentration of 62.6 mg/L. In conclusion, the biocarbon derived from Agave angustifolia bagasse exhibited significant potential for removing ibuprofen via adsorption from aqueous solutions.

The demand for new products derived from agro-industrial residues has increased recently. Furthermore, vinasse, a wastewater from ethanol production, needs treatment to be reused in the sugarcane industry, reducing industrial water consumption. This study performed vinasse filtration with charcoal from industrial sugarcane residues and used filtered molasses dilution in ethanolic fermentation. There were five treatments in randomized blocks with three repetitions. The treatments included deionized water and natural vinasse as positive and negative controls, respectively, and filtered vinasse from charcoal made from bamboo, sugarcane bagasse, and straw. Hence, fermentation for ethanol production was performed. Compared with natural vinasse, filtered vinasse with all types of charcoal showed lower soluble solids, total residual reducing sugars, higher ethanol concentrations, and greater fermentative efficiency. Filtered vinasse from bagasse and straw charcoals had efficiencies of 81.14% and 77.98%, respectively, in terms of ethanol production, which are close to those of deionized water (81.49%). In a hypothetical industry, vinasse charcoal filtration and charcoal regeneration should prevent 84.12% of water consumption from environmental resources. This process is feasible because it uses a product of sugarcane residue to treat wastewater and reduce industrial water consumption and vinasse disposal. HIGHLIGHTS Charcoal from sugar mill residues can be used for vinasse filtration.; The filtered vinasse should be used in molasses dilution.; Filtered vinasse has a fermentation efficiency close to deionized water in molasses dilution.; Using bagasse and straw charcoal for vinasse filtration in industry is feasible.; Charcoal regeneration is possible, and it may increase porosity.;

In order to alleviate the enormous pressure that waste bagasse puts on the environment, BGO was prepared from waste bagasse. With Ca2+ crosslinked SA as the first network and BGO as the heterogeneous nucleus for the second network, the PVA/SA/BGO double-network hydrogel spheres were constructed with the help of freeze-thaw method. The structure, morphology and adsorption properties of the PVA/SA/BGO double-network hydrogel for the organic dye crystalline violet (CV) were investigated. The results show that the obtained BGO has a lamellar structure and abundant oxygen-containing groups. The maximum adsorption amount of PVA/SA/BGO double-network hydrogel toward CV is 460.21 mg ⋅ g-1, and the adsorption process is in accordance with the Langmuir adsorption model and the pseudo-second-order kinetics model. [ABSTRACT FROM AUTHOR]

The aim of the current case study is to sequentially assess the heavy metals (HMs) cadmium (Cd), iron (Fe), lead (Pb) and zinc (Zn) in five products (raw juice, bagasse, mud-cake, refined sugar and molasses) along with the effluents of the selected sugar industry (SSI) Sindh, Pakistan. Estimations of daily intake and possible toxic risk of HMs by the consumption of sugar of SSI to end-user (families of SSI workers) of age group of 2.0–5.0, 6.0–15.0, 16.0–30.0 and 31.0–50.0 years were conducted. The high contents of HMs were observed in molasses followed by mud-cake and bagasse (raw waste). The raw juice of sugarcane and refined/white sugar showed the lowest levels of these HMs. The low levels of HMs in effluents of SSI might be to their separation at different stages of sugar processing and refining into the mud-cake, bagasse and molasses. The calculated daily intake of Fe and Zn from refined/white sugar to various study groups was found to be adequate based on the recommended levels by Food and Nutrition Board (FNB). The estimated weekly intake (WI) for Cd and Pb by the consumption of SSI sugar was significantly lower (2–5 times) than the provisional acceptable WI of Cd and Pb by WHO from foodstuff. The potential toxic risk study of Cd and Pb revealed that the studied subjects were not at potential toxic risk by the consumption of SSI sugar. [ABSTRACT FROM AUTHOR]

Wastewater containing polycyclic aromatic hydrocarbons (PAHs), when improperly managed or released into the environment, can disrupt the ecosystem and degrade the quality of water bodies. Wastewater that contains PAHs needs to be treated immediately. Bagasse was pyrolyzed in this work to produce alternate biochar, which was subsequently CO2-activated. CO2-activated and non-activated biochar were characterized and evaluated for adsorption of naphthalene from an aqueous solution. Thermodynamics, equilibrium, and adsorption kinetics studies were conducted. Contrary to non-activated biochar, which had a surface area of less than 71 m2/g, CO2-activated biochar was a typical mesoporous material with a surface area of roughly 263 m2/g. Therefore, compared to non-activated biochar, CO2-activated biochar has a more significant potential for naphthalene adsorption. CO2-activated and non-activated biochar had maximal naphthalene adsorption capacities of 290.43 and 38.15 mg/g, respectively. According to the findings, both feedstocks achieved the optimal adsorption capacity at pH 7, and 0.2 g of adsorbent at 120 and 180 min for activated and non-activated biochar, respectively. Naphthalene adsorption on CO2-activated biochar proceeded according to the pseudo-second-order model's kinetics. For CO2-activated biochar, with consideration to the equilibrium adsorption isotherms, Langmuir offered the best match. Physical modification considerably enhanced the adsorption of naphthalene onto CO2-activated biochar. Naphthalene and biochar were able to bind to one another by physical interaction, electrostatic attraction, hydrogen bonds, and π–π interaction. Naphthalene adsorption on CO2-activated biochar was spontaneous, exothermic, and favorable. Hence, modified biochar (CO2-activated) has the potential to produce a substitute mesoporous adsorbent from bagasse to remediate naphthalene from wastewater. [ABSTRACT FROM AUTHOR]

The utilization of biowastes for producing biochar to remove potentially toxic elements from water represents an important pathway for aquatic ecosystem decontamination. Here we explored the significance of thiol-functionalization on sugarcane bagasse biochar (Th/SCB–BC) and rice husk biochar (Th/RH–BC) to enhance arsenite (As(III)) removal capacity from water and compared their efficiency with both pristine biochars (SCB–BC and RH–BC). The maximum As(III) sorption was found on Th/SCB–BC and Th/RH–BC (2.88 and 2.51 mg g−1, respectively) compared to the SCB–BC and RH–BC (1.51 and 1.40 mg g−1). Relatively, a greater percentage of As(III) removal was obtained with Th/SCB–BC and Th/RH–BC (92% and 83%, respectively) at a pH 7 compared to pristine SCB–BC and RH–BC (65% and 55%) at 6 mg L−1 initial As(III) concentration, 2 h contact time and 1 g L−1 sorbent dose. Langmuir (R2 = 0.99) isotherm and pseudo-second-order kinetic (R2 = 0.99) models provided the best fits to As(III) sorption data. Desorption experiments indicated that the regeneration ability of biochars decreased and it was in the order of Th/SCB–BC (88%) > Th/RH–BC (82%) > SCB–BC (77%) > RH–BC (69%) up to three sorption–desorption cycles. Fourier-transform infrared spectroscopy and X-ray photoelectron spectroscopy results demonstrated that the thiol (-S–H) functional groups were successfully grafted on the surface of two biochars and as such contributed to enhance As(III) removal from water. Spectroscopic data indicated that the surface functional moieties, such as -S–H, − OH, − COOH, and C = O were involved to increase As(III) sorption on thiol-functionalized biochars. This study highlights that thiol-grafting on both biochars, notably on SCB–BC, enhanced their ability to remove As(III) from water, which can be used as an effective technique for the treatment of As from drinking water. [ABSTRACT FROM AUTHOR]

Gap-graded aggregate combined with asphalt rubber presents a high-performance alternative for roads with heavy traffic loads, offering advantages over conventional mixtures in terms of permanent deformation (rutting), fatigue life, and texture. In this study, the conventional filler in the well-established mixture was substituted with sugarcane bagasse bottom ash (SCBA) at a proportion of 5% of the total mineral aggregates. The objective was to enhance the mechanical performance of the asphalt coating while ensuring proper disposal of this waste material. Compared to conventional filler, SCBA is less dense, has smaller dimensions, and exhibits greater roughness, thereby affecting the volumetric parameters of the Marshall mix design. Consequently, the volume of voids in mineral aggregates and voids filled with asphalt increased while maintaining the same volume of air voids (5.3%). Consequently, there was a notable increase in Marshall Stability (40%) and Indirect Tensile Test (22%) mechanical parameters. Following laboratory analysis, the modified mixtures were applied as asphalt coating on a high-traffic highway (BR-158). Field specimens revealed an 18% increase in the Resilience Modulus (4088 MPa; 3478 MPa). Additionally, its Flow Number exhibited a 73% increase (16,707; 9681), and its permanent deformation rate was 28% lower within 10,000 cycles in the dynamic creep test. This was further supported by an 11% reduction in permanent deformation rate in the Hamburg Wheel Tracking Device (HWTD) within 20,000 cycles (3.2 mm; 3.6 mm). In conclusion, the partial replacement of conventional filler with sugarcane bagasse ash within the established granulometric range has demonstrated technical feasibility both in laboratory and field settings. [ABSTRACT FROM AUTHOR]