Search

In this study, a chloride-assisted boro/carbothermal reduction method was employed to prepare HfB 2 whiskers, aiming to address the challenges associated with large-scale preparation of HfB 2 whiskers and the development of high-temperature resistant electromagnetic wave absorbing materials. When the precursors were mechanically stirred, the resulting mixture underwent calcination at 1450 °C for 3 h, leading to the formation of single-phase HfB 2 whiskers. The as-synthesized HfB 2 whiskers showed exceptional resistance to oxidation at temperatures up to 700 °C. The microwave absorption performance and mechanism of the HfB 2 whiskers/paraffin composite were also investigated. The results revealed that the composite achieved a minimum reflection loss of −41.29 dB when the HfB 2 whiskers content reached 80 wt%, while the widest effective absorption bandwidth of the composite reached 3.6 GHz when the HfB 2 whiskers content increased to 82.5 wt%. This work presents a novel candidate for high-temperature resistant materials used in absorbing electromagnetic wave. [ABSTRACT FROM AUTHOR]

In this study, a chloride-assisted boro/carbothermal reduction method was employed to prepare HfB 2 whiskers, aiming to address the challenges associated with large-scale preparation of HfB 2 whiskers and the development of high-temperature resistant electromagnetic wave absorbing materials. When the precursors were mechanically stirred, the resulting mixture underwent calcination at 1450 °C for 3 h, leading to the formation of single-phase HfB 2 whiskers. The as-synthesized HfB 2 whiskers showed exceptional resistance to oxidation at temperatures up to 700 °C. The microwave absorption performance and mechanism of the HfB 2 whiskers/paraffin composite were also investigated. The results revealed that the composite achieved a minimum reflection loss of −41.29 dB when the HfB 2 whiskers content reached 80 wt%, while the widest effective absorption bandwidth of the composite reached 3.6 GHz when the HfB 2 whiskers content increased to 82.5 wt%. This work presents a novel candidate for high-temperature resistant materials used in absorbing electromagnetic wave. [ABSTRACT FROM AUTHOR]

Compared with common monoanionic high entropy ceramics, polyanionic high entropy ceramics, with better performance, are more difficult to prepare. Since transition metal carbides have high hardness and transition metal nitrides have good toughness, it is hoped that high entropy carbonitride ceramics can combine the advantages of the two. In this paper, a series of novel (Ti 0.25 Nb 0.25 Hf 0.25 Ta 0.25)C x N 1–x (x = 0.3, 0.4, 0.5, 0.6, and 0.7) high entropy ceramics were successfully synthesized for the first time using spark plasma sintering at 1850 °C with metal carbides and metal nitrides as raw materials. The phase evolution, microstructure, hardness and fracture toughness of high carbonitride entropy ceramics were investigated. X-ray diffraction indicates the ceramics with the single-phase face-centered cubic structure were successfully prepared. It was found that the high entropy ceramics sintered at 1850 °C with four cationic components have excellent performance on fracture toughness (KIC = 7.1746 MPa m1/2). With the increase of carbide proportion, the hardness of the ceramics increased, but the fracture toughness and bending strength decreased slightly. And it was found that the differences of grain size and porosity content were the main reasons for the mechanical properties difference. The excellent hardness properties, good bending strength and outstanding fracture toughness of the high entropy ceramics provide the possibility for the application of high entropy ceramics in aerospace and other applications requiring high performance. [ABSTRACT FROM AUTHOR]

Nowadays, the increasingly severe electromagnetic (EM) wave pollution requires high-performance EM wave absorbing materials. Multi-principal-element materials are acknowledged as promising for broadening the applications owing to their tunable chemistries and structures in many fields, including as EM wave absorbers. Herein, we prepared a high-entropy MXene, (Mo 0.25 Cr 0.25 Ti 0.25 V 0.25) 3 C 2 T x. Furthermore, multi-principal-element (Mo 0.25 Cr 0.25 Ti 0.25 V 0.25) 3 C 2 T x /FeCoNi and (Mo 0.25 Cr 0.25 Ti 0.25 V 0.25) 3 C 2 T x /FeCoNiCu composites were synthesized via an in-situ hydrothermal process by combining high-entropy MXene with medium-entropy magnetic alloys. In contrast with the relatively narrow effective absorption bandwidth (EAB) of (Mo 0.25 Cr 0.25 Ti 0.25 V 0.25) 3 C 2 T x MXene (2.56 GHz), (Mo 0.25 Cr 0.25 Ti 0.25 V 0.25) 3 C 2 T x /FeCoNi composite with 50 wt% MXene can attain an optimum EAB of 4.88 GHz with the matching thickness of only 1.73 mm. As for (Mo 0.25 Cr 0.25 Ti 0.25 V 0.25) 3 C 2 T x /FeCoNiCu composites, both the absorption efficiency and absorption bandwidth are significantly enhanced. The combination of multi-principal-component strategy and composite construction endows the composites with synergistic dielectric and magnetic losses, optimized impedance matching as well as enhanced attenuation ability, thus improving EM wave absorption performances. In addition, radar cross section (RCS) simulation confirms that the prepared composites have broad application prospects as radar stealth materials. [ABSTRACT FROM AUTHOR]

In view of the lack of conformal, load‐bearing, light‐weight, and high temperature‐resistant integrated wave‐absorbing composites suitable for extremely complex conditions, the gel‐casting process was successfully applied to porous Si3N4 wave‐absorbing composites in this work. A universal low‐slurry for gel casting was prepared by using two dispersants acting together (tetramethylammonium hydroxide solution and sodium lauryl sulfate), which ensured the smooth completion of the gel casting process. Combining the thermogravimetric and differential thermal gravity curves of the composite green body, reasonable parameters of the rubber discharge process are given to avoid the problem of the green body swelling and cracking. The porous TiC/Si3N4 composites were successfully prepared by holding them at 1650°C for 3 h. The bending strength, density, minimum reflection loss, absorption bandwidth, and matched thickness in the P‐band of the composites with 30 wt.% TiC addition were 54.08 ± 3.02 MPa, 1.906 g/cm3, ‐37.75 dB, 1.9 GHz, and 4.1 mm, respectively. The electromagnetic wave loss mechanisms of the composites are a combination of conductivity loss, multiple reflections and scattering, interfacial polarization, and defect polarization. [ABSTRACT FROM AUTHOR]

The relationship between the chemical elements of high-entropy boride (HEB) ceramics and their hardness is important for the prediction of high-hardness HEB ceramics. In this work, by designing four HEB ceramics with different chemical elements, the effect of lattice parameter difference factor (δ, represents the difference-degree in lattice parameters among the five individual constitute diborides) on phase composition and lattice-distortion, and the effect of rule of mixture (ROM) average hardness and lattice-distortion on HEB ceramics hardness were studied. The results indicated that, as δ value increases, more severe lattice-distortion occurs inside the HEB ceramics, and a single solid-solution is difficult to be formed. Furthermore, lattice-distortion and the ROM average hardness codetermine the HEB ceramics hardness. The greater lattice-distortion brings about significantly higher hardness for HEB ceramics than their ROM average hardness. Among the four HEBs, (Hf 0.2 Zr 0.2 Ta 0.2 V 0.2 Nb 0.2)B 2 exhibits the high hardness of 26 GPa measured using a load of 9.8 N. [ABSTRACT FROM AUTHOR]

In view of the lack of a conformal, load-bearing, lightweight, and high-temperature resistant integrated microwave-absorbing composites for applications under extremely complex conditions, this study successfully applies gel casting craft to porous Si 3 N 4 microwave-absorbing composites. The high-temperature decomposition reaction of Ti 3 SiC 2 powder was utilized to generate uniform Ti-C x -N 1−x grains in situ and to enhance the mechanical and microwave-absorption properties of porous Ti-C x -N 1−x /Si 3 N 4 composites. The bending strength, fracture toughness, density, maximum reflection loss value, absorption bandwidth and matched thickness in P-band of the composite with 30 wt% Ti 3 SiC 2 addition were 164.87 ± 7.56 MPa, 2.61 ± 0.13 MPa·m1/2, 2.077 g/cm3, 32.42 dB, 1.74 GHz and 4.2 mm, respectively. The fracture toughness and bending strength of the composite were increased by 71.71% and 58.13%, respectively, compared with monolithic porous Si 3 N 4. The electromagnetic wave loss mechanisms of the composites are proposed as a combination of conductivity loss, multiple reflections and scattering, interfacial polarization and defect polarization. [ABSTRACT FROM AUTHOR]

The TiB 2 fibers were prepared by a chloride-assisted carbothermic method accompanied with the vapor-liquid-solid (VLS) mechanism. The influences of TiO 2 , B 2 O 3 , C 12 H 22 O 11 , and calcination temperature on the yield of TiB 2 fibers were investigated. In addition, the effects of TiB 2 fibers content on the electromagnetic (EM) parameters and microwave absorption (MA) properties of TiB 2 fibers/paraffin composite was studied in detail. The TiB 2 fibers/paraffin composite showed excellent microwave absorption performance, with an optimized reflection loss (RL) of −46.63 dB at 14 GHz and a thickness of 1.5 mm. Moreover, it exhibited a broad effective absorption bandwidth (EAB) (RL < −10 dB) of 3.9 GHz, ranging from 12 to 15.9 GHz. TiB 2 fibers exhibit promising potential as materials for high-temperature applications in the field of MA. [ABSTRACT FROM AUTHOR]

In the recent years, MXenes (2D transition metal carbides, carbon nitrides and nitrides) and its precursor MAX phases have been widely investigated in electrochemical research. In this research, we successfully prepared a core-shell structured compound——Ti 3 C 2 @Ti 2 SnC/CNFs (MXene@TSC/C) as an anode material for lithium ion battery via electrospinning method. Results showed that this type of compound has a specific capacity of 288.9 mAh·g−1 at the current density of 0.4 A g−1 after 300 cycles, accompany with a retention rate of capacity of 105.4% in the rate performance test. These performances were benefit from the core-shell structured CNFs and Ti 3 C 2 MXenes. This work supported a novel way to improve the electrochemical property of MXene and MAX phases, which was expected to further explored. [ABSTRACT FROM AUTHOR]

A sol-gel method was employed for the synthesis of new High-entropy boride (HEB) powders, (Hf 0.2 Nb 0.2 Cr 0.2 Ta 0.2 Mo 0.2)B 2 , with nanoscale. The as-synthesized powders were obtained at a relatively low temperature of 1650 °C, and had small average particle size of 62.09 nm. X-ray diffraction confirmed that the (Hf 0.2 Nb 0.2 Cr 0.2 Ta 0.2 Mo 0.2)B 2 powders were hexagonal single-phase without any oxide impurities. In particular, electrochemical performance of the (Hf 0.2 Nb 0.2 Cr 0.2 Ta 0.2 Mo 0.2)B 2 powders with multiphase and high-entropy single phase were investigated using a three-electrode system. The improved electrochemical performance of the HEB powders is realized, with 27% higher in specific capacitance compared to the powders with multiphase. The HEB powders electrode exhibits a high capacitance retention of 97.03% after 5000 cycles. [ABSTRACT FROM AUTHOR]

The new inorganic material known as "high-entropy oxides" (HEOs) has a single-phase structure and is made up of several different main metal elements. It has many useful properties, including a high specific capacity, excellent cycling performance, high structural stability, and super-electronic conductivity. For lithium-ion batteries, it is viewed as a promising electrode material (LIBs). It is significant to develop high entropy oxides with different components and study their properties. Herein, Mg, Ni and Li are added to the quaternary medium entropy (CrFeMnCo)3O4. Four new spinel high entropy oxides were synthesized by glycine-nitrate SCS method at 750 °C and their material characterization and electrochemical properties were investigated respectively. The experimental results show that the four obtained samples have uniform particle size distribution. As for the electrochemical test, the capacities of the (CrFeMnCoMg)3O4 and (CrFeMnCoNi)3O4 do not decrease significantly after 800 cycles at 2000 mA·g−1. They have better cycle stability than the (CrFeMnCoMgLi)3O4 and (CrFeMnCoNiLi)3O4. As the anode of LIBs, all HEOs show excellent cycle stability and rate capability. This work provides a new strategy for designing high-entropy energy storage materials. [ABSTRACT FROM AUTHOR]

The present study investigated the dose-dependent effect of inositol on the thermally induced crystallization and phase evolution of amorphous calcium phosphate. It has been demonstrated that the crystallization of amorphous calcium phosphate was postponed by the introduction of inositol. The initial crystallize phase under 600 °C and thermodynamic equilibrium between α/β-tricalcium phosphate (TCP) under higher temperatures were altered in a content-dependent manner. Smaller amounts of inositol could promote the formation of α-TCP-like hydroxyapatite and expand the annealing temperature range to obtain pure α-TCP, while larger amounts would exhibit the opposite effect and promote the formation of β-TCP. This discovery could be used to guide the production of α/β-TCP. [ABSTRACT FROM AUTHOR]

The composition and synthesis approach of high entropy ceramics have significant influences on their microstructures and mechanical properties. A new (Hf 0.2 Zr 0.2 Ta 0.2 V 0.2 Nb 0.2)B 2 high entropy diboride ceramic with excellent mechanical properties was successfully prepared by spark plasma sintering (SPS) at a relatively "low temperature" (1800 °C) in this work. The effects of two mixing strategies, grinding and ball milling, on the solid solubility of the calcined powders were studied. Furthermore, the effects of these two mixing strategies on the phase and morphology of the calcined powders and the mechanical properties of the SPS sintered ceramics were analyzed. Experimental results indicated that, compared with a single solid solution phase within the high entropy boride powders obtained by ball milling, incomplete solid-solution presented in the high entropy boride powders obtained using grinding treatment. It promoted the solid-state diffusion and in-situ reaction of the diborides in the ceramics during the sintering process, thereby improving the densification and the hardness of the high entropy diboride ceramics. By grinding treatment, (Hf 0.2 Zr 0.2 Ta 0.2 V 0.2 Nb 0.2)B 2 high entropy ceramic with a relative density of 94% and a hardness of up to 25.34 ± 1.5 GPa at an indentation load of 9.8 N was obtained at 1800 °C. This work not only expanded the family of high-entropy diboride ceramics but also proved the advantage of grinding treatment in preparation of high entropy diboride ceramics. [ABSTRACT FROM AUTHOR]

The boron nitride nanosheets (BNNSs)/aluminum nitride (AlN) composites were prepared by hot press sintering at 1600°C. The microstructure, mechanical properties, and thermal conductivity of the samples were measured, and the effect of adding BNNSs to AlN ceramics on the properties was studied. It is found that the addition of BNNSs can effectively improve the mechanical properties of AlN. When the additional amount is 1 wt%, the bending strength of the sample reaches the maximum value of 456.6 MPa, which is 23.1% higher than that of the AlN sample without BNNSs. The fracture toughness of the sample is 4.47 MPa m1/2, a 68.7% improvement over the sample without BNNSs. The composites obtained in the experiment have brilliant mechanical properties. [ABSTRACT FROM AUTHOR]

Biphasic calcium phosphate (BCP) is an important research field based on calcium phosphate biomaterials. In this paper, a new synthesis method of CDHA/α-TCP BCP was studied. By controlling the addition amount of citric acid, the relative contents of CDHA and α-TCP in the BCP were controlled. BCP bone cement was prepared with different proportions of BCP as raw materials. The BCP bone cement was characterized by XRD and SEM, and evaluated by measuring setting time, compressive strength, SBF immersion, and colorimetric CCK-8 assay. The results showed that the increase of CDHA content can lead to the reduction of the setting time of bone cement and delay the degradation rate of BCP bone cement. [ABSTRACT FROM AUTHOR]

The fracture toughness and oxidation resistance are crucial factors affecting the practical applications of high-entropy diboride ceramics (HEBs). In this study, silicon carbide whiskers (SiC w) were introduced as a reinforcement for HEBs for the first time. To achieve a uniform dispersion of SiC w within the HEB powders, a combination of simultaneous ultrasonic dispersion, mechanical agitation, and freeze-drying technology was employed. Consequently, a series of composites, (Hf 0.2 Zr 0.2 Ta 0.2 V 0.2 Nb 0.2)B 2 -nSiC w (n = 0–20 vol%), were densified by spark plasma sintering. The effect of SiC w on the microstructure and mechanical properties of the HEBs were studied, as well as the toughening mechanism involved. The results revealed that the introduction of SiC w led to grain-size refinement in (Hf 0.2 Zr 0.2 Ta 0.2 V 0.2 Nb 0.2)B 2 , along with significant improvements in relative density, hardness, fracture toughness, and oxidation resistance. The relative density, hardness and fracture-toughness of (Hf 0.2 Zr 0.2 Ta 0.2 V 0.2 Nb 0.2)B 2 -SiC w composites exhibited an initial increase followed by a decrease with increasing SiC w content. Specifically, the (Hf 0.2 Zr 0.2 Ta 0.2 V 0.2 Nb 0.2)B 2 –15 vol% SiC w composite simultaneously obtained the highest hardness of 25.6 GPa and fracture-toughness of 4.8 MPa·m1/2, representing a 26% improvement compared to (Hf 0.2 Zr 0.2 Ta 0.2 V 0.2 Nb 0.2)B 2 ceramics. • The effect of SiC w on microstructure, mechanical properties and oxidation resistance of HEBs were studied for the first time. • The K Ic of (Hf 0.2 Zr 0.2 Ta 0.2 V 0.2 Nb 0.2)B 2 ceramic was increased by 26% without loss of hardness by introducing SiC w. • The oxidation resistance of HEBs was greatly enhanced due to the addition of SiC whiskers. [ABSTRACT FROM AUTHOR]

Compared to 1D compressed sensing (CS), 2D CS is more efficient for compressing the plaintext image from two directions, but security level of current 2D CS-based ciphers is unsatisfactory. To solve this problem, this paper presents a novel color image compression and encryption algorithm by combining 2D CS, information entropy and chaos. Firstly, the color image is decomposed into red, green and blue components, then they are sparsely transformed by the discrete wavelet transform (DWT) to get three sparse matrices. Next, the obtained matrices are observed by two asymptotical deterministic random measurement matrices based on information entropy and counter (ADMMIC), which not only encrypts the plaintext image, but also compresses it in proportion to reduce the transmission bandwidth and storage space. Subsequently, the corresponding measurement value matrices are shuffled by a double random scrambling based on Arnold map and index vector (DRSAIV) to eliminate the correlation between adjacent pixels. Furthermore, the obtained permutated matrices are diffused by a simultaneous multiple random diffusion of inter–intra components (SMRDIC) to obtain the final cipher image, the plaintext pixel to be diffused, the key matrix involved in diffusion and the position of the obtained ciphertext pixel are all unpredictable, which makes statistical attack invalid. In addition, information entropy values of plaintext image are obtained to generate the initial values of the used chaotic systems, which greatly improve the ability to resist the known-plaintext and chosen-plaintext attacks. Simulation results and security analyses verify that this algorithm has good compression and high security. [ABSTRACT FROM AUTHOR]

In this work, we synthesized K2Ti6O13 nanowires coated with sulfur-doped carbon for the first time, with fulvic acid and cystine as the carbon source, which exhibit higher capacity and rate performance compared with pure potassium titanate. Via analyzing the cyclic voltammetry curves obtained at different scan rates, it is revealed that the capacity increase is due to the improved ion diffusivity induced by the carbon coating. Moreover, cystine is demonstrated to be a better carbon source than fulvic acid. [ABSTRACT FROM AUTHOR]

Nickel ferrite owns a lot of advantages as electrode materials for supercapacitor, such as high energy density and excellent theoretical capacity. Whereas, the electrochemical performances of NiFe 2 O 4 in terms of rate performance and cycle stability are not satisfactory due to the low conductivity. While carbon fiber is a kind of material with high conductivity. Hence, NiFe 2 O 4 @ slit modified hollow carbon fiber is obtained through the coaxial electrospinning method. The slits on hollow carbon fibers are beneficial to the contact of inner NiFe 2 O 4 nanoparticles with electrolyte. Results of electrochemical tests show that at a current density of 1 A/g, the specific capacitance of NiFe 2 O 4 @ slit modified hollow carbon fiber is calculated to be 225.4 F/g, higher than that of NiFe 2 O 4 nanoparticles of 134.8 F/g. Moreover, a better cycle and rate performances (100 % vs 80 %; 71.9 % vs 47.5 %) are achieved. This work displays that slit modified hollow carbon fiber can improve the electrochemical performance of NiFe 2 O 4 efficiently. [Display omitted] • Carbon fibers are introduced to enhance the rate and cycle performances of NiFe 2 O 4. • Slits are obtained utilizing Al 2 O 3 sacrificial hard templates. • Slits are beneficial to the contact of NiFe 2 O 4 and electrolyte. [ABSTRACT FROM AUTHOR]

• The Zn 8 B 3 H 3 O 14 nanosheets were discovered and efficiently synthesized by the one-step coprecipitate method. • This method is simple, high yield and low cost to prepare Zn 8 B 3 H 3 O 14 nanosheets. • The nanosheets have good thermal stability, and their decomposition temperature reaches 414 °C. With the rapid development of two-dimensional materials, the exploration of new two-dimensional materials has become a research hotspot. In this work, novel Zn 8 B 3 H 3 O 14 nanosheets were efficiently synthesized by the one-step coprecipitate method using the water bath reaction at 70 °C for 24 h. The preparation of Zn 8 B 3 H 3 O 14 nanosheets by this method has the advantages of a simple preparation process, low cost, low equipment requirements, and mass production. The microstructure and morphology of nanosheets were characterized in detail. In addition, the nanosheets have good thermal stability properties, and their decomposition temperature reaches 414 °C. This allows the nanosheets to adopt higher processing and service temperatures when applied to polymer materials. [ABSTRACT FROM AUTHOR]

BNNSs were prepared efficiently by magnesium borate nitridation. BNNSs/eutectic-composition Al 2 O 3 /YAG/YSZ ceramics were prepared by hot pressing sintering. The addition of BNNSs did not change the phase composition of BNNSs/eutectic-composition Al 2 O 3 /YAG/YSZ ceramics. The bending strength and fracture toughness of 1.5wt%BNNSs/ eutectic-composition Al 2 O 3 /YAG/YSZ ceramic were increased by 19.0% and 18.9% respectively. Doped BNNSs exist at the grain boundary between two or more different grains. The toughening mechanism of BNNSs contains mainly crack deflection, BNNSs pullout and BNNSs bridging. • BNNSs/eutectic-composition Al 2 O 3 /YAG/YSZ ceramics were originally prepared with excellent mechanical properties. • The toughening mechanism of BNNSs was discussed. • The effects of temperature and BNNSs doping amount on the mechanical properties of ceramics were explored. [ABSTRACT FROM AUTHOR]

In this paper, BNNSs/Al 2 O 3 composite powder was prepared by in-situ reaction using borate nitridation method and BNNSs/Al 2 O 3 composite ceramics were prepared by hot-pressing sintering. This method achieves uniform mixing of BNNSs and Al 2 O 3 ceramic matrix and reduces the introduction of impurities in the processing process. The BNNSs/Al 2 O 3 composite ceramics have excellent bending strength (549.4 MPa), fracture toughness (5.18 MPa m1/2) and hardness (21.3 GPa). The high hardness of composite ceramics is attributed to high grain boundary strength and density. The reinforcing mechanisms of ceramics include BNNSs pull-out, BNNSs bridging, crack deflection as well as the transgranular fracture and intergranular fracture of Al 2 O 3 matrix. [ABSTRACT FROM AUTHOR]

As the precursor of MXenes (2D transition metal carbides, carbon nitrides and nitrides), MAX phase materials have attracted ever-increasing attention in electrochemical applications. In this work, we have successfully hybridized a MAX phase, Ti 2 SnC, with various ratios of carbon nanofibers (CNFs) via electrospinning. The results show that the Ti 2 SnC/CNFs compounds possess a stable lithium ion storage ability as an anode material, reaching a stable specific capacity of up to 367.5 mAh·g−1 after 500 charge/discharge cycles at the current density of 1.0 A g−1, which are drastically better than some other MAX phase materials such as Ti 3 SiC 2 and Nb 2 SnC. This strategy provides a new pathway for the improvement of the electrochemical stability of MAX phase, which has a wide application prospect. • Ti 2 SnC/CNFs was successfully prepared by an electrospinning method. • CNFs retard the volume expansion of Ti 2 SnC during the charge/discharge process. • Ti 2 SnC/CNFs performed stable lithium ion capacitance (367.5 mAh·g−1 at 1.0 A g−1). [ABSTRACT FROM AUTHOR]

• The partial S-doping NiFe 2 O 4 was obtained through a facile hydrothermal method. • The d-spacing of NiFe 2 O 4 was expended caused by partial S-doping. • The impact of partial S-doping to NiFe 2 O 4 is exposed by VASP analysis. • The optimal electrode exhibited the highest specific capacitance of 284 F/g. Nickel ferrite exhibits many advantages as electrode materials in the application of supercapacitor, such as high energy capacity and excellent cycle stability. Whereas, compared with identical-metal sulfides, the specific capacitance of NiFe 2 O 4 is still insufficient. Hence, to combine the superiorities of oxides and sulfides, partial sulfur doping NiFe 2 O 4 is obtained through hydrothermal synthesis method. Analyzed by Vienna Ab-initio Simulation Package (VASP) software and high-resolution transmission electron microscopy, the lattice parameters of NiFe 2 O 4 are confirmed to be expanded by introducing sulfur atoms, which is beneficial to electrochemical performances. At a current density of 1 A/g, the specific capacitance of partial sulfur doping NiFe 2 O 4 is calculated to be 284 F/g, higher than that of the original NiFe 2 O 4 of 182.2 F/g. Moreover, a maximum energy density of 21.14 Wh/kg is achieved at a power density of 375 W/kg. This work shows that partial sulfur doping could improve the electrochemical performance of NiFe 2 O 4. To sum up, this work provides an effective way to enhance the poor electrochemical performance of oxides, greatly encouraging the application of oxides in energy storage field. [Display omitted] [ABSTRACT FROM AUTHOR]

MAX phase materials, the precursors of MXenes (2D transition metal carbides, carbon nitrides, and nitrides), have become increasingly popular in electrochemical applications. In this study, we have successfully prepared Ti 2 SnC with high lithium capacity via the in-situ formation of SnO 2. Results show that there are TiC nanowhiskers and SnO 2 inside the Ti 2 SnC MAX calcined at 800 ℃, and the initial specific capacity could reach 377 and 371 mAh·g−1 at high current densities of 400 mA·g−1 and 1.0 A·g−1, respectively. These values are higher than those of most MAX phase materials reported in previous studies, such as Ti 3 SiC 2 and Nb 2 SnC, but the stability and rate performance are inferior, which is a direction for the future. This paper provides a new pathway for the application of MAX phases in electrochemistry, which has more in-depth application prospects. ● Ti 2 SnC with in-situ formation of SnO 2 was successfully prepared by a calcination method. ● The Ti 2 SnC layered structure slows down the volume expansion of in-situ prepared SnO 2. ● This anode material performed a better specific capacitance, arriving at 377 mAh/g at the current density of 1.0 A/g. [ABSTRACT FROM AUTHOR]

Transitional metal nitrides (TMNs) are regarded as comparatively promising electrode materials for supercapacitor due to the high electronic conductivity, good corrosion resistance and special electron structure. Herein, in this work a heterostructure Co 2 N-Ni 3 N nanosheets-nanowires arrays grown on Ni foam (NF) are designed and synthesized by a simple hydrothermal reaction and nitriding treatment. The prepared Co 2 N-Ni 3 N/NF nanoarrays has a high electrical conductivity, abundant surface active sites, charge transfer channels and the synergy effect between each component, which makes it exhibit outstanding electrochemical performance. Electrochemical test results revealed that the areal capacitance of Co 2 N-Ni 3 N/NF was 2.17 F cm−2 at 1 mA cm−2 using a three-electrode system in 1 M KOH. Meanwhile, when the current density increases to 20 mA cm−2, it can still retain 62.21% of the original capacitance, suggesting a good rate capability. In addition, in two-electrode test with Co 2 N-Ni 3 N/NF as the positive electrode and activated carbon as the negative electrode, a maximum energy density of 145.65 μWh cm−2 is shown when the power density is 0.75 mW cm−2. And it has 85.90% capacitance retention after 5000 cycles. [Display omitted] • Unique Co 2 N-Ni 3 N nanoarray heterostructure was successfully synthesized. • Co 2 N-Ni 3 N/NF achieves an areal capacitance 2.17 F cm-2 at current density of 1 mA cm-2. • The Co 2 N-Ni 3 N/NF // AC exhibits good electrochemical performance in two-electrode tests. [ABSTRACT FROM AUTHOR]

How to deal with the brittleness of ceramic materials is always one of the hot topics in the field of materials science. Design of layered ceramics with textured structure is one of the effective methods to improve their fracture toughness. The introduction of additives as interlayer phases can balance fracture toughness and flexural strength. However, the research about addition of interlayer phases and their mechanisms in the layered ceramics is still limited. In this work, nacre-like alumina ceramics were successfully fabricated by freeze casting followed by hot pressing. Silicon nitride was incorporated as the interlayer phase, and the effect on the mechanical properties of the nacre-like alumina was investigated. The addition of silicon nitride was beneficial to improvement of interlayer bonding between the alumina layers due to formation of sialon phase, leading to increase of flexural strength but decease of fracture toughness. When the content of silicon nitride was 3.3 wt%, flexural strength and fracture toughness of the sample was 468 MPa and 6.2 MPa m1/2, respectively. Compared with the sample without silicon nitride, the flexural strength was enhanced significantly. Additionally, both flexural strength and fracture toughness were improved as compared the sample without any additives. This work can provide available references for design and fabrication of high-strength and high-toughness ceramics by properly tuning the layer structure and interlayer phase composition. [ABSTRACT FROM AUTHOR]

[Display omitted] • Three non-resonant SiOC-based meta-structures are synthesized by 3D printing. • The metamaterials achieve good impedance matching through structural design. • The reflection loss is −55.68 dB with an ultra-wideband absorption of 11.88 GHz. • The mechanisms between meta-structures and electromagnetic wave are investigated. Lightweight, wide-band ceramic-based electromagnetic (EM) absorbers have great application demand in the field of high-temperature EM wave absorption. However, it is difficult for traditional ceramic-based structural EM absorbing materials (EMAMs) to balance the contradiction between broadband absorption and good impedance matching due to resonance effect. Herein, three novel non-resonant SiOC-based triply periodic minimal surface (TPMS) meta-structures named Schoen G (SG), Schwarz D (SD) and Schwarz P (SP) with a density of 0.556 g/cm3 were successfully synthesized by digital light processing (DLP) 3D printing and polymer-derived ceramics (PDCs) method. Through the structural design of multilayer arrays and holes, three metamaterials achieve good impedance matching and broadband EM absorption. The effective absorption bandwidth (EAB) of all three meta-structures reaches 9.80 GHz (8.2–18.0 GHz) in a wide matching thickness range, covering the entire X-Ku band. In addition, the minimum reflection loss (RL min) of −55.68 dB is obtained at a matching thickness of 3.02 mm for SD meta-structure in X-band. Besides, the SG meta-structure tested by the arch method has an ultra-wide EAB of 11.88 GHz (6.12–18.0 GHz), exhibiting ultra-broadband EM absorption properties. It is significant that the intrinsic relationships between TPMS meta-structures and EM responses are explored by CST simulation. This work provides a new perspective for the design of lightweight, broadband ceramic-based EM metamaterial absorbers under high-temperature, harsh environments. [ABSTRACT FROM AUTHOR]

In this study, Zn 8 B 3 H 3 O 14 nanosheets were synthesized through a one-step coprecipitation process and employed as both a boron source and substrate templates for the fabrication of boron nitride nanosheets (BNNSs), which were synthesized efficiently at low temperatures by the borate nitration method using ammonia as the nitrogen source. The thickness of the synthesized BNNSs ranged from 3 to 10 nm with a flake dimension of about 2.56 μm. The prepared BNNSs using this method realized 98.8% boron source utilization and single batch yields up to gram level. In addition, BNNSs/SiO 2 microwave-transparent composites were prepared to investigate the potential for large-scale applications of the BNNSs produced by using this method. The composites demonstrated a remarkable increase in bending strength and fracture toughness, reaching 122.02 MPa and 2.31 MPa·m1/2, respectively, with the addition of only 0.5 wt% BNNSs. Compared with SiO 2 without BNNSs, the fracture toughness of the composites is increased by 106%. A novel crack plugging strong toughening mechanism of BNNSs is proposed. Simultaneously, the composites exhibit exceptional microwave-transparent properties, with dielectric constants below 4 in the real part and below 0.03 in the imaginary part. Therefore, this study has successfully achieved the low-temperature and efficient synthesis of micron-scale BNNSs, laying the groundwork for their large-scale application. [Display omitted] • Zn 8 B 3 H 3 O 14 nanosheets were used as substrate templates for the synthesis of BNNSs. • BNNSs were synthesized with high efficiency at low temperatures (900 °C). • The single batch yield of BNNSs reached up to the gram level. • The BNNSs/SiO 2 wave-transparent composites with ultrahigh toughness were obtained. • A novel mechanism for strengthening and toughening (BNNSs plugging) is proposed. [ABSTRACT FROM AUTHOR]

The microstructure and mechanical properties of (Hf 0.2 Nb 0.2 Ta 0.2 Ti 0.2 Zr 0.2)B 2 high-entropy boride (HEB) were first predicted by first-principles calculations combined with virtual crystal approximation (VCA). The results verified the suitability of VCA scheme in HEB studying. Besides, single-phase (Hf 0.2 Nb 0.2 Ta 0.2 Ti 0.2 Zr 0.2)B 2 ceramics were successfully fabricated using boro/carbothermal reduction (BCTR) method and subsequent spark plasma sintering (SPS); furthermore, the effects of different amounts of B 4 C on microstructure and mechanical properties were evaluated. Due to the addition of B 4 C and C, all samples formed single-phase solid solutions after SPS. When the excess amount of B 4 C increased to 5 wt%, the sample with fine grains exhibited superior comprehensive properties with the hardness of 18.1 ± 1.0 GPa, flexural strength of 376 ± 25 MPa, and fracture toughness of 4.70 ± 0.27 MPa m1/2. Nonetheless, 10 wt% excess of B 4 C coarsened the grains and decreased the strength of the ceramic. Moreover, the nanohardness (34.5–36.9 GPa) and Young's modulus (519–571 GPa) values with different B 4 C contents just showed a slight difference and were within ranges commonly observed in high-entropy diboride ceramics. [ABSTRACT FROM AUTHOR]

Silica is one of the most widely used ceramics due to its excellent chemical stability and dielectric property. However, its destructive brittle nature inhabits it from wider application as a functional ceramic. An improvement in toughness is a challenging topic for silica ceramic, as well as other ceramics. In the paper, silica ceramic with different types of boron nitride powders and alumina platelets was fabricated by hot-pressing. Introduction of the additives had great influence on the composites' mechanical properties and microstructure. The silica matrix composite containing micro-sized boron nitride powders possessed the best mechanical properties, including the bending strength (134.5 MPa) and the fracture toughness (1.85 Mpa·m1/2). Meanwhile, the introduction of alumina platelets combined with boron nitride nanosheets achieved an effective enhancement of fracture toughness while maintaining the bending strength. Compared with the monolithic silica, the composite with simultaneous addition of alumina platelets and boron nitride nanosheets had a fracture toughness of 2.23 Mpa·m1/2, increased by approximately 27% (1.75 Mpa·m1/2). The crack deflection and platelet pullout were contributing to enhancement of the fracture toughness. The improved mechanical properties, combined with the intrinsic excellent dielectric and chemical properties, make the silica matrix composites promising wave transparent and thermal protection materials. [ABSTRACT FROM AUTHOR]

Alumina is one of the most commonly used and researched structural ceramic because of its excellent properties. However, its intrinsic brittleness is the fatal drawback, which hinders it from wider applications. How to improve its fracture toughness as well as the bending strength is always challenging for material researchers. In this paper, alumina matrix composites were fabricated by hot-pressing, in which some additives, including zirconia, alumina platelets, and MXene, were incorporated. The influence of the introduced additives on their microstructure and mechanical properties was investigated. Compare with the monolithic alumina, both bending strength and fracture toughness of all samples were improved greatly. Incorporation of zirconia was beneficial to the mechanical properties due to the phase-transformation strengthening and toughening mechanism. While alumina platelets resulted in high fracture toughness because of the self-toughening of elongated grains. The synergistic effect of alumina platelets and MXene enormously improved the fracture toughness from 2.9 ± 0.3 MPa·m1/2 for monolithic alumina to 7.5 ± 0.4 MPa·m1/2 for the composite, which was increased by 159%. This work will provide useful references for the fabrication of high-strength and high-toughness alumina ceramics by introducing additives properly. [ABSTRACT FROM AUTHOR]

Synergic effect of graphene oxide (GO) and silicon nitride whisker (Si 3 N 4 w) on the mechanical properties of nacre-like alumina was investigated in this study. A comprehensive analysis on the composites, including microstructure, relative densities, flexural strength and fracture toughness, was carried out. The experimental results showed that, GO promoted the fracture toughness of the composites, but reduced the flexural strength slightly; while adding a certain amount of Si 3 N 4 w improved both flexural strength and fracture toughness. With the incorporation of GO and Si 3 N 4 w, the highest flexural strength reached 520 MPa and the fracture toughness reached 9.59 MPa m1/2. Microstructure observation revealed that the enhanced mechanical properties were ascribed to the synergistic toughening mechanisms induced by the nacre-like structure of alumina, GO pull-out, Si 3 N 4 w pinning and pull-out. [ABSTRACT FROM AUTHOR]

• High-entropy carbides powders were synthesized by carbothermal reduction method. • The solid-solution elements have a great influence on EMW absorption capability. • The intrinsic characteristics make the high-entropy carbides promising EMW absorbing materials. The electromagnetic wave absorption performance of high-entropy transition metal carbides, including (Ti 0.2 Zr 0.2 Hf 0.2 Nb 0.2 Ta 0.2)C, (Ti 0.2 Zr 0.2 Mo 0.2 Nb 0.2 Ta 0.2)C and (Ti 0.2 Zr 0.2 Cr 0.2 Nb 0.2 Ta 0.2)C, was investigated in the frequency from 2 GHz to 18 GHz. The electromagnetic parameter measurement and subsequent electromagnetic wave absorption evaluation showed that the high-entropy transition metal carbides possessed good electromagnetic wave absorbing properties, which had a great relation to the solid-solution elements. The (Ti 0.2 Zr 0.2 Mo 0.2 Nb 0.2 Ta 0.2)C with a 1.50 mm thickness displayed a minimal reflection loss of -32.1 dB, and the effective absorption bandwidth (<-10 dB) was in the frequency range of 13–18 GHz. Intriguingly, the minimum reflection loss reached -36.6 dB at the thickness of 2.50 mm. The electromagnetic wave absorption performance was mainly associated with conductivity loss and dipole polarization, which originated from intrinsic conductivity of the high-entropy carbides and lattice distortion resulting from solid solution of multiple elements, respectively. The experimental results show that the high-entropy transition metal carbides may be promising structural-functional integrated ceramics in wide applications. The single-phase high-entropy transition metal carbide powders without complex structure and multi phases design present excellent EMW absorption properties, including minute reflection loss and broad absorption bandwidth. [Display omitted] [ABSTRACT FROM AUTHOR]

• A distinctive strategy of Sb doped quaternary oxide material is proposed. • The enhanced Na+ diffusion kinetics and meliorative equilibrium conductance is due to the Sb substitution. • The prepared cathode O3-NaNi 0.5-x Mn 0.3 Ti 0.2 Sb 0.03 O 2 reveals discharge capacity of 147.8 mAh g −1. The poor cycle stability and rate capability for sodium-ion batteries is largely due to electrochemical irreversibility and sluggish mobility of Na+ in the cathode materials. Herein, a new strategy of introducing Sb ions into the ternary oxide NiMnTi-based layer-structured cathode material is designed. Reversible phase transition in this cathode NMTSb 0.03 restraint the rapid capacity decay issued from intense volume variation, exhibiting a reversible capacity of 147.8 mAh g−1 and retaining 103.5 mAh g−1 over 200 cycles at 1C. The enough space after Sb substitution allows the effective accommodation of Na+ intercalation and deintercalation, affording a specific capacity of 90 mAh g−1 at 8C. The improvement is attributed to the enhanced Na+ diffusion kinetics with the meliorative equilibrium conductance and the higher cohesive energy after Sb doping. Considering its simple preparation and scale-up capability, the O3-type NaNi 0.5 Mn 0.3 Ti 0.2 O 2 with Sb5+may find extensive applications in designing electrode for sodium-ion batteries. [ABSTRACT FROM AUTHOR]